Commit graph

3624 commits

Author SHA1 Message Date
Cyril Chemparathy
da1ec42aaf ARM1176: TI: TNETV107X soc initial support
TNETV107X is a Texas Instruments SoC based on an ARM1176 core, and with a
bunch on on-chip integrated peripherals.  This is an initial commit with
basic functionality, more commits with drivers, etc. to follow.

Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-06-07 14:13:32 -04:00
Cyril Chemparathy
b87996d24a ARM1176: Coexist with other ARM1176 platforms
The current ARM1176 CPU specific code is too specific to the SMDK6400
architecture.  The following changes were necessary prerequisites for the
addition of other SoCs based on ARM1176.

Existing board's (SMDK6400) configuration has been modified to keep behavior
unchanged despite these changes.

1. Peripheral port remap configurability
The earlier code had hardcoded remap values specific to s3c64xx in start.S.
This change makes the peripheral port remap addresses and sizes configurable.

2. U-Boot code relocation support
Most architectures allow u-boot code to run initially at a different
address (possibly in NOR) and then get relocated to its final resting place
in RAM.  Added support for this capability in ARM1176 architecture.

3. Disable TCM if necessary
If a ROM based bootloader happened to have initialized TCM, we disable it here
to keep things sane.

4. Remove unnecessary SoC specific includes
ARM1176 code does not really need this SoC specific include.  The presence
of this include prevents builds on other ARM1176 archs.

5. Modified virt-to-phys conversion during MMU disable
The original MMU disable code masks out too many bits from the load address
when it tries to figure out the physical address of the jump target label.
Consequently, it ends up branching to the wrong address after disabling the
MMU.

Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-06-07 14:13:27 -04:00
George G. Davis
409a07c9d7 ARM1136: Fix cache_flush() error and correct cpu_init_crit() comments
The ARM1136 cache_flush() function uses the "mcr p15, 0, rn, c7, c7, 0"
instruction which means "Invalidate Both Caches" when in fact the intent
is to clean and invalidate all caches.  So add an "mcr p15, 0, %0, c7,
c10, 0" instruction to "Clean Entire Data Cache" prior to the "Invalidate
Both Caches" instruction to insure that memory is consistent with any
dirty cache lines.

Also fix a couple of "flush v*" comments in ARM1136 cpu_init_crit() so
that they correctly describe the actual ARM1136 CP15 C7 Cache Operations
used.

Signed-off-by: George G. Davis <gdavis@mvista.com>
2010-06-01 06:44:09 -05:00
Tom
39c209546a ARM Update mach-types
Fetched from http://www.arm.linux.org.uk/developer/machines/download.php
And built with

repo http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm
commit 3defb2476166445982a90c12d33f8947e75476c4

Signed-off-by: Tom <Tom@bumblecow.com>
2010-05-28 13:23:16 -05:00
Tom
551bd947bd ARM Update mach-types
Fetched from http://www.arm.linux.org.uk/developer/machines/download.php
And built with

repo http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm
commit 257dab81413b31b8648becfe11586b3a41e5c29a

Signed-off-by: Tom <Tom@bumblecow.com>
2010-05-28 11:49:42 -05:00
Wolfgang Denk
40792d675a a320evb: fix udelay / __udelay confusion
Fix the following compiler problems:

arch/arm/cpu/arm920t/a320/liba320.a(timer.o): In function `udelay':
/home/wd/git/u-boot/work/arch/arm/cpu/arm920t/a320/timer.c:160: multiple definition of `udelay'
lib/libgeneric.a(time.o):/home/wd/git/u-boot/work/lib/time.c:34: first defined here
lib/libgeneric.a(time.o): In function `udelay':
time.c:(.text+0x1c): undefined reference to `__udelay'

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-05-21 23:14:53 +02:00
Wolfgang Denk
92381c41c7 ARM: */timer.c: fix spelling and vertical alignment
Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-05-21 23:13:18 +02:00
Wolfgang Denk
8a452c2c17 Merge branch 'master' of git://git.denx.de/u-boot-imx 2010-05-21 22:22:23 +02:00
Wolfgang Denk
cd4b02be1b ARM: add __aeabi_unwind_cpp_pr0() function to avoid linker complaints
Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Thomas Weber <weber@corscience.de>
2010-05-15 19:50:36 +02:00
Fabio Estevam
60381d6878 MX51: Fix MX51 CPU detect message
Fix MX51 CPU detect message.

Original string was:
CPU:   Freescale i.MX51 family 3.0V at 800 MHz

which can be misinterpreted as  3.0 Volts instead of the silicon revision.

,change it to:
CPU:   Freescale i.MX51 family rev3.0 at 800 MHz

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2010-05-05 09:48:41 +02:00
Asen Dimov
d6b91e30d3 at91: define matrix registers bit fields
Signed-off-by: Asen Dimov <dimov@ronetix.at>
2010-04-30 05:23:26 -05:00
Stefano Babic
eab40f819d MX31: Support 128MB RAM on QONG module
The QONG module can be downsized and delivered
with 128MB instead of 256MB. The patch adds
run time support for the two different memory
configurations.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-04-30 05:23:26 -05:00
Stefano Babic
efb9591069 MX31: add pin definitions for NAND controller
Add pin definitions ralted to the NAND controller to be used
to set up the pin multiplexer.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-04-30 05:23:25 -05:00
Stefano Babic
7d27cd08b4 MX31: add accessor function to get a gpio
The patch adds an accessor function to get the value of a gpio.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-04-30 05:23:25 -05:00
John Rigby
34196b0a8b MX25 print arm clock instead of mpllclk on boot
Replace call to imx_get_mpllclk with imx_get_armclk
to show frequency of ARM core instead of mpll internal
bus in print_cpuinfo.

Signed-off-by: John Rigby <jcrigby@gmail.com>
CC: Stefano Babic <sbabic@denx.de>
2010-04-30 05:23:24 -05:00
Stefano Babic
5e1fe88fe3 Moved board specific values in config file
The lowlevel_init file contained some hard-coded values
to setup the RAM. These board related values are moved into
the board configuration file.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-04-30 05:23:24 -05:00
Heiko Schocher
1e65c2beb5 arm, mx27: add support for SDHC1 pin init
Signed-off-by: Heiko Schocher <hs@denx.de>
2010-04-30 05:23:23 -05:00
Minkyu Kang
3bb6b037e8 SAMSUNG: make s5p common gpio functions
Because of s5pc1xx gpio is same as s5p seires SoC,
move gpio functions to drvier/gpio/
and modify structure's name from s5pc1xx_ to s5p_.

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2010-04-30 05:23:23 -05:00
Minkyu Kang
46a3b5c8df SAMSUNG: serial: modify name from s5pc1xx to s5p
Because of other s5p series SoC will use these serial functions,
modify function's name and structure's name.

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2010-04-30 05:23:23 -05:00
Alexander Holler
47eb08a97e at91: add defines for RTT and GPBR
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
2010-04-30 05:23:22 -05:00
trix
7bc8768039 ARM Update mach-types
Fetched from http://www.arm.linux.org.uk/developer/machines/download.php
And built with

repo http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm
commit 85b3cce880a19e78286570d5fd004cc3cac06f57

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2010-04-30 05:23:21 -05:00
Peter Tyser
84ad688473 arm: Move cpu/$CPU to arch/arm/cpu/$CPU
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-04-13 09:13:24 +02:00
Peter Tyser
819833af39 Move architecture-specific includes to arch/$ARCH/include/asm
This helps to clean up the include/ directory so that it only contains
non-architecture-specific headers and also matches Linux's directory
layout which many U-Boot developers are already familiar with.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-04-13 09:13:12 +02:00
Peter Tyser
ea0364f1bb Move lib_$ARCH directories to arch/$ARCH/lib
Also move lib_$ARCH/config.mk to arch/$ARCH/config.mk

This change is intended to clean up the top-level directory structure
and more closely mimic Linux's directory organization.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-04-13 09:13:03 +02:00