Add support for the Arm Versatile Express config bus that is
being used for exposing various subsystems via a generic
configuration bus. This driver adds support for generating
transactions on this configuration bus and can be used by
other drivers to abstract the communication with the actual
function providers.
Signed-off-by: Liviu Dudau <liviu.dudau@foss.arm.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
- fixes to rkimage for SPL boot via USB
- fixes to make_fit_atf.py, incl. entry-point calculation and python3
compatibility
- OP-TEE support for ARMv7-based SoCs
- fixes to RGMII/GMII selection on the RK3328
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbt0FOAAoJECaAFcEOcohNZmcH/A1mKO0/R4tHCqFP2j0I+OuP
PClkA1HUZuD5phvPMaxdHQBwsq7sAa8AljK1oPCNkslP7mFxToUUBx7xc0vB89P/
D+XsI4uce89hIyTULR2FdhR22MOk41zaLVeNicpQ1keCNbzCwsHsHTA+B4XN/xNe
tdPpu6wN2D+g88DAv+/ebVYgjmxRvFD4qpL9bbZpOqqA8XCcD31ukCR2E4fsESgn
mzwKaKcX6SeYgTVCT8Q15SLTNI1WRUY1Y1laj1WKl4abY+HsTt4Whm9imM2l3K5W
ODj6vnFlwEC9rgdxmtXGcmBfwtyXubSfuZDrMGFAiOlyIUgpPXWZI7i8LYQbZ7s=
=NdBl
-----END PGP SIGNATURE-----
Merge tag 'rockchip-for-v2018.11-rc2' of git://git.denx.de/u-boot-rockchip
Rockchip-focused changes for v2018.11-rc2:
- fixes to rkimage for SPL boot via USB
- fixes to make_fit_atf.py, incl. entry-point calculation and python3
compatibility
- OP-TEE support for ARMv7-based SoCs
- fixes to RGMII/GMII selection on the RK3328
Signed-off-by: Tom Rini <trini@konsulko.com>
Using PHY internal delays in combination with the phy-mode
rgmii-id/rxid/txid was not possible. Only rgmii was supported.
Now we can disable rockchip's gmac delay lines and also use
rgmii-id/rxid/txid.
Based on commit eaf70ad14cbb ("net: stmmac: dwmac-rk: Add
handling for RGMII_ID/RXID/TXID") for mainline linux kernel.
Signed-off-by: Janine Hagemann <j.hagemann@phytec.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
We have to use RK3328_RXCLK_DLY_ENA_GMAC_ENABLE instead of
RK3328_RXCLK_DLY_ENA_GMAC_MASK in rk3328_gmac_set_to_rgmii()
to enable the RX delay.
The MASK was used in a wrong way.
Signed-off-by: Janine Hagemann <j.hagemann@phytec.de>
Reviewed-by: Philipp Tomisch <philipp.tomisch@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds the SPI driver for the MediaTek MT7688 SoC (and
derivates). Its been tested on the LinkIt Smart 7688 and the Gardena
Smart Gateway with and SPI NOR on CS0 and on the Gardena Smart
Gateway additionally with an SPI NAND on CS1.
Note that the SPI controller only supports a max transfer size of 32
bytes. This driver implementes a workaround to enable bigger xfer
sizes to speed up the transfer especially for the SPI NAND support.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Piotr Dymacz <pepe2k@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch adds support for Gigadevices SPI NAND device to the new SPI
NAND infrastructure in U-Boot. Currently only the 128MiB GD5F1GQ4UC
device is supported.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: Jagan Teki <jagan@openedev.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
This patch adds support for 2 new XMC (Wuhan Xinxin Semiconductor
Manufacturing Corp) SPI NOR chips.
This support can be enabled by selecting the SPI_FLASH_XMC Kconfig
option.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Change to use managed resource function devm_kcalloc(),
so it will auto free memory when driver is removed.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add a PHY driver for the R-Car Gen3 which allows configuring
USB OTG PHY on Gen3 into host mode and toggles VBUS in case a
dedicated regulator is present.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The Arm Versatile Express I2C controller is a simple register-based
controller that uses a register to control the state of the SCL and
SDA lines. Add support for it.
Signed-off-by: Liviu Dudau <liviu.dudau@foss.arm.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This is the PR for SPI-NAND changes along with few spi changes.
[trini: Re-sync changes for ls1012afrwy_qspi*_defconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add DM support to the SH QSPI driver while retaining non-DM support.
The later is required as this driver is used in SPL which has a size
limitation of 16 kiB.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
[jagan: use proper commit head]
Reviewed-by: Jagan Teki <jagan@openedev.com>
Convert fsl_qspi.c to complete DM mode.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Tested-by: Rajat Srivastava <rajat.srivastava@nxp.com>
Tested-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add code to reset all reset signals as in SPI DT node. A reset property
is an optional feature, so only print out a warning and do not fail if a
reset property is not present.
If a reset property is discovered, then use it to deassert, thus
bringing the IP out of reset.
Release reset when _remove().
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
There should not be a 'nand' command, a 'sf' command and certainly not
a new 'spi-nand' command. Write a 'mtd' command instead to manage all
MTD devices/partitions at once. This should be the preferred way to
access any MTD device.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Instead of collecting partitions in a flat list, create a hierarchy
within the mtd_info structure: use a partitions list to keep track of
the partitions of an MTD device (which might be itself a partition of
another MTD device), a pointer to the parent device (NULL when the MTD
device is the root one, not a partition).
By also saving directly in mtd_info the offset of the partition, we
can get rid of the mtd_part structure.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Using an MTD device (resp. partition) name in mtdparts is simple and
straightforward. However, for a long time already, another name was
given in mtdparts to indicate a device (resp. partition) so the
"mtdids" environment variable was created to do the match.
Let's create a function that, from an MTD device (resp. partition)
name, search for the equivalent name in the "mtdparts" environment
variable thanks to the "mtdids" string.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
The current parser is very specific to U-Boot mtdparts implementation.
It does not use MTD structures like mtd_info and mtd_partition. Copy
and adapt the current parser in drivers/mtd/mtd-uclass.c (to not break
the current use of mtdparts.c itself) and write some kind of a wrapper
around the current implementation to allow other commands to benefit
from this parsing in a user-friendly way.
This new function will allocate an mtd_partition array for each
successful call. This array must be freed after use by the caller.
The given 'mtdparts' buffer pointer will be moved forward to the next
MTD device (if any, it will point towards a '\0' character otherwise).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
The user might want to trigger the probe of any MTD device, export these
functions so they can be called from a command source file.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
The rk3188 works nicely with the rockchip mmc driver, so we just need
to add the different compatible for it - as used in the Linux kernel.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
While trying to enable the dw_mmc on rk3188 I managed to confuse
and hang the dw_mmc controller into not delivering further data.
The fifo state never became ready and the driver was iterating in
the while loop reading 0-byte packets forever.
So inspired by how other implementations handle this, check the fifo-
state beforhand and add a timeout to catch any glaring fifo issues
without hanging uboot altogether.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
MSM uses the chipidea controller IP, however it requires
to reinit the phy after controller reset. in EHCI mode there's a
dedicated callback for it.
In device mode however there's no such callback.
Add implementaion of ci_init_after_reset() to implement the above
requirement in case CI_UDC driver is used.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
MSM variant of Chipidea must reinitalize the phy
after controller reset.
Introduce ci_init_after_reset() weak function that
can be used to achieve the above init.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Add a PHY driver for the Qualcomm dragonboard 410c which
allows switching on/off and resetting the phy connected
to the EHCI controllers and USBHS controller.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
platdata_auto_alloc_size was not initialized in structure.
Caused null pointer dereference when configuring device as
gadget.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Since commit 7b3b74d321 ("serial: serial_stm32: Enable overrun")
on STM32F7xx based boards, the first lines of serial output are
missing during boot (we no more see the U-Boot release version,
board model and DRAM size).
By enabling the uart FIFO on STM32F7, the complete U-boot log
can be sent correctly.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The Arm Versatile Express and Juno development boards contain an
OSC clock generator that can be accessed through the Versatile
Express config bus. The generators are quite often being controlled
by some MCU and the config bus offers a uniform way of exposing them.
Signed-off-by: Liviu Dudau <liviu.dudau@foss.arm.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add a test which verifies that all subnodes under "/firmware"
nodes are scanned.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added 'imply FIRMWARE' to sandbox Kconfig to fix test failures, fixed
ordering of lines in arch/sandbox/dts/test.dts and test/dm/Makefile,
updated #if condition in drivers/firmware/firmware-uclass.c:
Signed-off-by: Simon Glass <sjg@chromium.org>
There is no prompt string for FIRMWARE config. Without this,
FIRMWARE config cannot be enabled through menuconfing or
config file. Fix this by adding prompt summary.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since there is no canonical "board device" that can be used in board
files, it is difficult to use DM function for board initialization in
these cases.
Hence, add a uclass that implements a simple "board device", which can
hold devices not suitable anywhere else in the device tree, and is also
able to read encoded information, e.g. hard-wired GPIOs on a GPIO
expander, read-only memory ICs, etc. that carry information about the
hardware.
The devices of this uclass expose methods to read generic data types
(integers, strings, booleans) to encode the information provided by the
hardware.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
We cannot use device structures to disable devices, since getting
them with the API functions would bind and activate the device, which
would fail if the underlying device does not exist.
Reviewed-by: Simon Glass <sjg@chromium.org>
Implement a set of functions to manipulate properties in a live device
tree:
* ofnode_write_prop() to set generic properties of a node
* ofnode_write_string() to set string properties of a node
* ofnode_set_enabled() to either enable or disable a node
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
LS1043A, LS1046A, LS1088A, LS2088A.
Switch to driver model for SATA on LS1021A and LS1043A.
Add support for LS1012AFRWY rev C board.
Enable SMMU for LS1043A.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XRFI
-----END PGP SIGNATURE-----
Merge tag 'fsl-qoriq-for-v2018.11-rc1' of git://git.denx.de/u-boot-fsl-qoriq
Switch to driver model for eSDHC on Layerscape SoCs including LS1021A,
LS1043A, LS1046A, LS1088A, LS2088A.
Switch to driver model for SATA on LS1021A and LS1043A.
Add support for LS1012AFRWY rev C board.
Enable SMMU for LS1043A.
With DM_GPIO and DM_MMC translating GPIO_ACTIVE_LOW, any boards
using the 'cd-invert' option will no longer need to do this. This
patch removes the support for 'invert' from the MMC driver.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Fix warning over when !DM_GPIO]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add a driver that supports Maxim 1 wire EEPROMs families
DS24B33 and DS2431.
Can be extended for other families as well.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
[eugen.hristev@microchip.com: reworked driver]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
When a new device is discovered, this may be a w1 eeprom device.
Attempt to find the proper node and driver from the w1-eeprom subsystem.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
