All 32-bit Armada SoCs and also 64-bit Armada 3720 SoC can load and boot
firmware from SATA disk. This adds support for updating firmware binary for
these SoCs. On 32-bit Armada SoC is firmware stored at sector 1 and on
Armada 3720 is stored at MBR partition 0x4d or GPT partition with type GUID
6828311A-BA55-42A4-BCDE-A89BB5EDECAE (Marvell Armada 3700 Boot partition).
Signed-off-by: Pali Rohár <pali@kernel.org>
Support for burning into the correct eMMC HW boot partition was broken and
removed in commit 96be2f0727 ("mvebu: bubt: Drop dead code"). Reimplement
this functionality and bring it back again.
Fixes: 96be2f0727 ("mvebu: bubt: Drop dead code")
Signed-off-by: Pali Rohár <pali@kernel.org>
Despite the official specification, Marvell BootROM does not interpret
srcaddr from SATA image as number of sectors the beginning of the hard
drive, but as number of sectors relative to the main header.
Reject invalid and accept valid SATA images.
Fixes: 5a06534933 ("cmd: mvebu/bubt: Check for A38x image data checksum")
Signed-off-by: Pali Rohár <pali@kernel.org>
Despite the official specification, Marvell BootROM does not interpret
srcaddr from SDIO image as offset in number of sectors (like for SATA
image), but as offset in bytes (like for all other images except SATA).
To ensure that we do not store invalid SDIO image to the boot location
(read by the Marvell BootROM), we need to check that image is valid
and srcaddr is intepreted in bytes, in the same way as it is done by
Marvell BootROM.
This fixes rejecting valid and accepting invalid SDIO images by bubt command.
Fixes: 5a06534933 ("cmd: mvebu/bubt: Check for A38x image data checksum")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reserved blocks are used for storing bad block tables. With "nand bad"
command, these reserved blocks are shown as bad blocks. This is leading
to confusion when compared with Linux bad blocks. Hence, display
"bbt reserved" when printing reserved blocks with "nand bad" command.
To acheive this, return 2 which represents reserved from nand_isbad_bbt()
instead of 1 in case of reserved blocks and catch it in cmd/nand.c.
"nand bad" command display's hexadecimal numbers, so add "0x" prefix.
Example log will show up as below.
ZynqMP> nand bad
Device 0 bad blocks:
0x00400000
0x16800000
0x16c00000
0x17000000
0x3d800000
0x3e400000
0xe8400000
0xff000000 (bbt reserved)
0xff400000 (bbt reserved)
0xff800000 (bbt reserved)
0xffc00000 (bbt reserved)
0x116800000
0x116c00000
0x1ff000000 (bbt reserved)
0x1ff400000 (bbt reserved)
0x1ff800000 (bbt reserved)
0x1ffc00000 (bbt reserved)
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-By: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Measures the DTB passed to the EFI application upon new boolean config
switch CONFIG_EFI_TCG2_PROTOCOL_MEASURE_DTB. For platforms where the
content of the DTB passed to the OS can change across reboots, there is
not point measuring it hence the config switch to allow platform to not
embed this feature.
Co-developed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Tested-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
- mvebu: Support for 2 new Armada 385 boards (Tony)
- mvebu: Minor misc board enhancements (Tony)
- kirkwood: Serial driver fixes (Kconfig & dtsi) (Tony)
- cmd: return code when tlv_eeprom incorrectly called (Heinrich)
A command called with incorrect parameters should set $? to 1 (false).
Instead of calling cmd_usage(cmdtp) and then returning 0 just return
CMD_RET_FAILURE.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
At the moment every subcommand of "fdt", except "addr" itself, requires
the DT address to be set first. We explicitly check for that before even
comparing against the subcommands' string.
This early bailout also affects the "move" subcommand, even though that
does not require or rely on a previous call to "fdt addr". In fact it
even sets the FDT address to the target of the move command, so is a
perfect beginning for a sequence of fdt commands.
Move the check for a previously set FDT address to after we handle the
"move" command also, so we don't need a dummy call to "fdt addr" first,
before being able to move the devicetree.
This skips one pointless "fdt addr" call in scripts which aim to alter
the control DT, but need to copy it to a safe location first (for
instance to $fdt_addr_r).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The "fdt move" subcommand was using the provided DTB addresses directly,
without trying to "map" them into U-Boot's address space. This happened
to work since on the vast majority of "real" platforms there is a simple
1:1 mapping of VA to PAs, so either value works fine.
However this is not true on the sandbox, so the "fdt move" command fails
there miserably:
=> fdt addr $fdtcontroladdr
=> cp.l $fdtcontroladdr $fdt_addr_r 40 # simple memcpy works
=> fdt move $fdtcontroladdr $fdt_addr_r
Segmentation fault
Use the proper "map_sysmem" call to convert PAs to VAs, to make this
more robust in general and to enable operation in the sandbox.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The clock UCLASS need to be probed to allow availability of the
private data (struct clk *), get in show_clks() with dev_get_clk_ptr()
before use them.
Without this patch the clock dump can cause crash because all the
private data are not available before calling the API clk_get_rate().
It is the case for the SCMI clocks, priv->channel is needed for
scmi_clk_get_rate() and it is initialized only in scmi_clk_probe().
This issue causes a crash for "clk dump" command on STM32MP135F-DK board
for SCMI clock not yet probed.
Fixes: 1a725e2290 ("clk: fix clock tree dump to properly dump out every registered clock")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20221213145708.v2.1.Ia0bc6b272f1e2e3f37873c61d79138c2663c4055@changeid
Documentation:
* Provide page with links to talks on U-Boot
UEFI:
* Enable CTRL+S to save the boot order in eficonfig command
* Run attribute check for QueryVariableInfo() only for the file store
* Bug fixes
Others:
* Improve output formatting of the coninfo command
-----BEGIN PGP SIGNATURE-----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=HVHT
-----END PGP SIGNATURE-----
Merge tag 'efi-2023-04-rc2' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2023-04-rc2
Documentation:
* Provide page with links to talks on U-Boot
UEFI:
* Enable CTRL+S to save the boot order in eficonfig command
* Run attribute check for QueryVariableInfo() only for the file store
* Bug fixes
Others:
* Improve output formatting of the coninfo command
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 10 Feb 2023 12:15:45 PM EST
# gpg: using RSA key 6DC4F9C71F29A6FA06B76D33C481DBBC2C051AC4
# gpg: Good signature from "Heinrich Schuchardt <xypron.glpk@gmx.de>" [unknown]
# gpg: aka "[jpeg image of size 1389]" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 6DC4 F9C7 1F29 A6FA 06B7 6D33 C481 DBBC 2C05 1AC4
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_EFI_SECURE_BOOT defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_EFI_MM_COMM_TEE defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_VIDEO_ANSI defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 2 usages of this option to the non-SPL form, since there is
no SPL_VIDEO defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_USB_FUNCTION_FASTBOOT defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_UDP_FUNCTION_FASTBOOT defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
This converts 5 usages of this option to the non-SPL form, since there is
no SPL_SYS_LONGHELP defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
The change boot order menu in eficonfig can have at most INT_MAX lines
and it is troublesome to scroll down to the "Save" entry.
This commit assigns CTRL+S to save the boot order.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
On the sandbox called without "--terminal raw" CTRL+C leaves U-Boot,
"ESC/CTRL+C to quit" is misleading.
Let's remove CTRL+C to quit key handling from bootmenu and eficonfig menu.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Device name are typically longer than 8 characters. This leads to ragged
output.
Only the I and O bit of the device flags are of interest for the user.
Writing a hexadecimal number is just confusing.
Before the patch the output looked like this:
=> coninfo
List of available devices:
pl011@9000000 00000007 IO stdin stdout stderr
serial 00000003 IO
usbkbd 00000001 I.
With the patch the output looks like this:
=> coninfo
List of available devices
|-- pl011@9000000 (IO)
| |-- stdin
| |-- stdout
| |-- stderr
|-- serial (IO)
|-- usbkbd (I)
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts 3 usages of this option to the non-SPL form, since there is
no SPL_CMD_TFTPPUT defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_CMD_NVEDIT_EFI defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 2 usages of this option to the non-SPL form, since there is
no SPL_CMD_EFICONFIG defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a command to load SEAMA (Seattle Image), a NAND flash
on-flash storage format.
This type of flash image is found in some D-Link routers such
as DIR-645, DIR-842, DIR-859, DIR-860L, DIR-885L, DIR890L and
DCH-M225, as well as in WD and NEC routers on the ath79
(MIPS), Broadcom BCM53xx, and RAMIPS platforms.
This U-Boot command will read and decode a SEAMA image from
raw NAND flash on any platform. As it is always using big endian
format for the data decoding is always necessary on platforms
such as ARM.
The command is needed to read a SEAMA-encoded boot image on the
D-Link DIR-890L router for boot from NAND flash in an upcoming
port of U-Boot to the Broadcom Northstar (BCM4709, BCM53xx)
architecture.
A basic test and documentation is added as well. The test must
be run on a target with NAND flash support and at least one
resident SEAMA image in flash.
Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is currently in the cmd/ file but we want to call it from a driver.
Move it into a common place. Tidy up the header-file order while we are
here.
Signed-off-by: Simon Glass <sjg@chromium.org>
This uses casts all over the place. Use the correct type so that these
can be avoided, as is done with other commands. Also simplify a few
conditionals.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is sometimes useful to have one without the other, e.g. on a device
without a display, since at present the expo feature requires CONFIG_VIDEO
to be enabled.
Update the Makefile and bootflow command to support this, as well as the
EXPO dependency.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add more capable "bkops" command which allows enabling and disabling both
manual and automatic bkops. The existing 'mmc bkops-enable' subcommand is
poorly named to cover all the possibilities, hence the new-ish subcommand.
Note that both commands are wrappers around the same common code.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The current eficonfig menu does not support vertical scroll,
so it can not display the menu entries greater than
the console row size.
This commit add the vertial scroll support.
The console size is retrieved by
SIMPLE_TEXT_OUTPUT_PROTOCOL.QueryMode() service, then
calculates the row size for menu entry by subtracting
menu header and description row size from the console row size.
"start" and "end" are added in the efimenu structure.
"start" keeps the menu entry index at the top, "end" keeps
the bottom menu entry index. item_data_print() menu function
only draws the menu entry between "start" and "end".
This commit also fixes the issue that "Save" and "Quit"
entries can be moved by BKEY_PLUS in change boot order menu.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This commit removes the change boot order specific
menu implementation. The change boot order implementation
calls eficonfig_process_common() same as other menus.
The change boot order menu requires own item_data_print
and item_choice implementation, but display_statusline
function can be a same function as other menus.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Current change boot order implementation does not call
eficonfig_process_common() and call own menu functions
for display_statusline, item_data_print and item_choice.
Change boot order functionality should call
eficonfig_process_common() to improve maintenanceability.
This commit is a preparation to remove the change boot
order specific implementation. The menu functions
(display_statusline, item_data_print and item_choice) are
added as argument of eficonfig_process_common().
The menu description string displayed at the bottom of
the menu is also added as argument.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
* Use 16 digits on 64 bit systems.
* Use 64 bit patterns on 64 bit systems.
* Expect the sign bit in bit 63 on 64 bit systems.
* Adjust the formatting of a constant.
* Always print result on new line
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Stefan Roese <sr@denx.de>
If the offset or the size passed to the 'sf erase' command exceeds
the size of the SPI flash displaying the command usage is not
helpful. Return CMD_RET_FAILURE instead of CMD_RET_USAGE.
Use the CMD_RET_* constants instead of 0, 1, -1.
Simplify a logical expression in the final return statement.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Acked-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
CMD_RET_USAGE == -1. The special handling of this value at the end of
do_spi_flash() does not make any sense.
To avoid future confusion use the CMD_RET_* constants and simplify the
code.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
If the offset or the size passed to the 'sf write' or 'sf read' command
exceeds the size of the SPI flash displaying the command usage is not
helpful. Return CMD_RET_FAILURE instead of CMD_RET_USAGE.
Use the CMD_RET_* constants instead of 0, 1, -1.
Simplify a logical expression in the final return statement.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This function is not used outside tests. Drop it and rename
bootflow_scan_dev() since it is how we start a scan now.
Signed-off-by: Simon Glass <sjg@chromium.org>
We want to support scanning a single label, like 'mmc' or 'usb0'. Add
this feature by plumbing the label through to the iterator, setting a
flag to indicate that only siblings of the initial device should be used.
This means that scanning a bootdev by its name is not supported anymore.
That feature doesn't seem very useful in practice, so it is no great loss.
Add a test for bootdev_find_by_any() while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current extension code is designed to be used from commands. We want
to add a boot driver which uses it. To help with this, split the code into
the command processing and a function which actually does the scan.
Really the extension code should be in common/ or use driver model, but
this is a start.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a flag to control whether hunters are used when scanning for
bootflows. Enable it by default and tidy up the flag comments a little.
Fow now this has no effect, until a future patch enables this feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
These are associated with the ethernet boot device but do not match its
uclass name, so handle them as special cases.
Provide a way to pass flags through with the bootdev so that we know
how to process it. The flags are checked by the bootmeths, to ensure that
only the selected bootmeth is used.
While these both use the network device, they work quite differently. It
is common to run only one of these, or to run PXE before DHCP. Provide
bootflow flags to control which methods are used. Check these in the two
bootmeths so that only the chosen one is used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some bootmeths provide a way to load a device tree as well as the base
OS image. Add a way to store this in the bootflow. Update the
'bootflow info' command to show this information.
Note that the device tree is not allocated, but instead is stored at
an address provided by an environment variable. This may need to be
adjusted at some point, but for now it works well and fits in with the
existing distro-boot scripts.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this must be done by executing the command. Also it involves
fiddling with the environment to determine the correct autoload behaviour.
Ideally it should be possible to run network operations without even
having the command line present (CONFIG_CMDLINE).
For now, add a function to handle DHCP, so it can be called from a bootdev
more easily.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add a way to run a bootdev hunter to find bootdevs of a certain type. Add
this to the 'bootdev hunt' command. Test for this are added in a later
patch, since a useful test needs some hunters to work with.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some bootdevs must be enumerated before they appear. For example, USB
bootdevs are not visible until USB is enumerated.
With standard boot this needs to happen automatically, since we only
want to enumerate a bus if it is needed.
Add a way to define bootdev 'hunters' which can be used to hunt for
bootdevs of a given type. Track which ones have been used and add a
command to list them.
Include a clang work-around which seems to be needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
This needs to be able to work (at least partially) without the bloblist
active. Add a condition for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
At this point, the remaining places where we have a symbol that is
defined as CONFIG_... are in fairly odd locations. While as much dead
code has been removed as possible, some of these locations are simply
less obvious at first. In other cases, this code is used, but was
defined in such a way as to have been missed by earlier checks. Perform
a rename of all such remaining symbols to be CFG_... rather than
CONFIG_...
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This implements the following command:
part type mmc 0:1
-> print partition type UUID
part type mmc 0:1 uuid
-> set environment variable to partition type UUID
"part type" can be useful when writing a bootcmd which searches for a
specific partition type to enable automatic discovery of partitions and
their intended usage or mount point.
Signed-off-by: Enric Balletbo i Serra <eballetbo@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Fix when CONFIG_PARTITION_TYPE_GUID is disabled and have the
command check for "types" before "type"]
Signed-off-by: Tom Rini <trini@konsulko.com>
The event framework is just that, a framework. Enabling it by itself
does nothing, so we shouldn't ask the user about it. Reword (and correct
typos) around this the option and help text. This also applies to
DM_EVENT and EVENT_DYNAMIC. Only EVENT_DEBUG and CMD_EVENT should be
visible to the user to select, when EVENT is selected.
With this, it's time to address the larger problems. When functionality
uses events, typically via EVENT_SPY, the appropriate framework then
must be select'd and NOT imply'd. As the functionality will cease to
work (and so, platforms will fail to boot) this is non-optional and
where select is appropriate. Audit the current users of EVENT_SPY to
have a more fine-grained approach to select'ing the framework where
used. Also ensure the current users of event_register and also select
EVENT_DYNAMIC.
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reported-by: Oliver Graute <Oliver.Graute@kococonnector.com>
Reported-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Fixes: 7fe32b3442 ("event: Convert arch_cpu_init_dm() to use events")
Fixes: 42fdcebf85 ("event: Convert misc_init_f() to use events")
Fixes: c5ef202557 ("dm: fix DM_EVENT dependencies")
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The first name is taken from command name that's why shouldn't be listed in
help. The similar change was also done by commit a84d3b6c56 ("cmd: pwm:
Remove additional pwm description").
Also remove additional spaces in help message.
Before:
event event list - list event spies
After:
event list - list event spies
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Create an expo to handle the boot menu. For now this is quite simple, with
just a header, some menu items and a pointer to show the current one.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some operating systems provide a logo in bmp format. Read this in if
present so it can be displayed in the menu.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add the concept of an OS name to the bootflow. This typically includes the
OS name, version and kernel version.
Implement this for the distro and script bootmeths so that it works with
Armbian and older version of Fedora.
Signed-off-by: Simon Glass <sjg@chromium.org>
Support for fonts currently depends on the type of vidconsole in use. Add
two new methods to enumerate fonts and to set the font.
Fix a few other method comments while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should use the cmd/ directory for commands rather than for common code
used elsewhere in U-Boot. Move the common 'source' code into
image-board.c to achieve this.
The image_source_script() function needs to call run_command_list() so
seems to belong better in the command library. Move and rename it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Split this functionality out of the 'source' command so it can be used
from another place. For now leave it where it is, but a future patch will
move it out of cmd/
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the return value to save having to pass around a pointer. This also
resolves any ambiguity about what *key contains when the function is
called.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the return value to save having to pass around a pointer. This also
resolves any ambiguity about what *key contains when the function is
called.
Signed-off-by: Simon Glass <sjg@chromium.org>
When only sspi is entered, help information can be printed.
Signed-off-by: chenzhipeng <chenzhipeng@eswincomputing.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make sure the 'exit' command as well as 'exit $val' command exits
from environment scripts immediately and propagates return value
out of those scripts fully. That means the following behavior is
expected:
"
=> setenv foo 'echo bar ; exit 1' ; run foo ; echo $?
bar
1
=> setenv foo 'echo bar ; exit 0' ; run foo ; echo $?
bar
0
=> setenv foo 'echo bar ; exit -2' ; run foo ; echo $?
bar
0
"
As well as the followin behavior:
"
=> setenv foo 'echo bar ; exit 3 ; echo fail'; run foo; echo $?
bar
3
=> setenv foo 'echo bar ; exit 1 ; echo fail'; run foo; echo $?
bar
1
=> setenv foo 'echo bar ; exit 0 ; echo fail'; run foo; echo $?
bar
0
=> setenv foo 'echo bar ; exit -1 ; echo fail'; run foo; echo $?
bar
0
=> setenv foo 'echo bar ; exit -2 ; echo fail'; run foo; echo $?
bar
0
=> setenv foo 'echo bar ; exit ; echo fail'; run foo; echo $?
bar
0
"
Fixes: 8c4e3b79bd ("cmd: exit: Fix return value")
Reviewed-by: Hector Palacios <hector.palacios@digi.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Much of the fastboot code predates the introduction of Kconfig and
has quite a few #ifdefs in it which is unnecessary now that we can use
IS_ENABLED() et al.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # on vim3l
When the number of parameters is wrong, the return value should be processed in
the same way as other cmds, return CMD_RET_USAGE so that it can print the information.
Signed-off-by: Shenlin Liang <liangshenlin@eswincomputing.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The two configuration CONFIG_MTDIDS_DEFAULT and CONFIG_MTDPARTS_DEFAULT
are not needed with mtd configuration CONFIG_SYS_MTDPARTS_RUNTIME which
allows the MTDIDS and MTDPARTS to be configured at runtime.
This patch has no defconfig impacts because CONFIG_SYS_MTDPARTS_RUNTIME
is only used by two platforms (stm32mp and igep00x0) which don't define
CONFIG_MTDIDS_DEFAULT or CONFIG_MTDPARTS_DEFAULT.
This patch solves an UBI environment load issue for NAND boot for
stm32mp15 platform. In mtd_uboot.c, when GD_FLG_ENV_READY is not set,
env_get_f() return a EMPTY string, define in default_environment[]
because CONFIG_MTDIDS_DEFAULT="" and CONFIG_MTDPARTS_DEFAULT="",
but a NULL pointer is expected to allow call of board_mtdparts_default.
Without mtdparts, the env partition [CONFIG_ENV_UBI_PART="UBI"] is not
found in env/ubi.c [CONFIG_ENV_IS_IN_UBI].
It is not a problem when env becomes ready, as these empty variables are
removed form U-Boot environment in env_import() / himport_r().
Fixes: a331017c23 ("Complete migration of MTDPARTS_DEFAULT / MTDIDS_DEFAULT, include in environment")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
It is incorrect to keep commands in the arch/ folder.
Signed-off-by: Alexey Romanov <avromanov@sberdevices.ru>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230110105650.54580-3-avromanov@sberdevices.ru
[narmstrong: moved after cmd/sound in index.rst]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
A parameter starting with a hyphen leads to an endless loop in the sound
play command.
Leave it to dectoul() to handle the hyphen. It will return 0 for a negative
number.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As discussed previously [1,2], the source command is not safe to use with
verified boot unless there is a key with required = "images" (which has its
own problems). This is because if such a key is absent, signatures are
verified but not required. It is assumed that configuration nodes will
provide the signature. Because the source command does not use
configurations to determine the image to source, effectively no
verification takes place.
To address this, allow specifying configuration nodes. We use the same
syntax as the bootm command (helpfully provided for us by fit_parse_conf).
By default, we first try the default config and then the default image. To
force using a config, # must be present in the command (e.g. `source
$loadaddr#my-conf`). For convenience, the config may be omitted, just like
the address may be (e.g. `source \#`). This also works for images
(`source :` behaves exactly like `source` currently does).
[1] https://lore.kernel.org/u-boot/7d711133-d513-5bcb-52f2-a9dbaa9eeded@prevas.dk/
[2] https://lore.kernel.org/u-boot/042dcb34-f85f-351e-1b0e-513f89005fdd@gmail.com/
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This simplifies a few lines and corrects an error message.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The wget command uses TCP, but fails to select PROT_TCP in Kconfig.
Instead it selects the non-existing symbol TCP. Fix the typo.
Signed-off-by: Michael Walle <michael@walle.cc>
This functionality is part of the legacy I2C subsystem and is currently
unused anywhere. Remove the remaining references.
Signed-off-by: Tom Rini <trini@konsulko.com>
The signed null key with authenticated header is used to clear
the PK, KEK, db and dbx. When CONFIG_EFI_MM_COMM_TEE is enabled
(StMM and OP-TEE based RPMB storage is used as the EFI variable
storage), clearing KEK, db and dbx by enrolling a signed null
key does not work as expected if EFI_VARIABLE_APPEND_WRITE
attritube is set.
This commit checks the selected file is null key, then
EFI_VARIABLE_APPEND_WRITE attibute will not be used for the null key.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The current code calls efi_set_variable_int() to delete the
invalid boot option between calls to efi_get_next_variable_name_int(),
it may produce unpredictable results.
This commit moves removal of the invalid boot option outside
of the efi_get_next_variable_name_int() calls.
EFI_NOT_FOUND returned from efi_get_next_variable_name_int()
indicates we retrieved all EFI variables, it should be treated
as EFI_SUCEESS.
To address the checkpatch warning of too many leading tabs,
combine two if statement into one.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
To retrieve the EFI variable name by efi_get_next_variable_name_int(),
the sequence of alloc -> efi_get_next_variable_name_int ->
realloc -> efi_get_next_variable_name_int is required.
In current code, this sequence repeatedly appears in
the several functions. It should be curved out a common function.
This commit also fixes the missing free() of var_name16
in eficonfig_delete_invalid_boot_option().
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Currently the sound command accepts only one value each for duration and
frequency. Allowing more duration and frequency arguments enables playing a
tune.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Complete the migration of MTDPARTS_DEFAULT / MTDIDS_DEFAULT in Kconfig;
this patch removes the support of MTDIDS_DEFAULT / MTDPARTS_DEFAULT
in the configuration files (include/configs/*.h).
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
As reported by patch [1], the `mtd erase' command should not erase bad
blocks.
To force bad block erasing you have to use the `mtd erase.dontskipbad'
command.
This patch tries to fix the same issue without modifying code taken
from the linux kernel, in order to make further upgrades easier.
[1] https://lore.kernel.org/all/20221006031501.110290-2-mikhail.kshevetskiy@iopsys.eu/
Suggested-by: Michael Trimarchi <michael@amarulasolutions.com>
Co-developed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Co-developed-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Tested-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Extract the information about ecc strength and ecc step size
from mtd controller. This information is usefull to check if
what we think as ecc is what we really configured.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20220922133937.277463-1-michael@amarulasolutions.com
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
As there are no more non-DM_ETH cases for networking, remove this legacy
file and update the Makefile to match current usage.
Signed-off-by: Tom Rini <trini@konsulko.com>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_SDRAM
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NUM
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Implement ping6 command to ping hosts using IPv6. It works the same way as
an ordinary ping command. There is no ICMP request so it is not possible
to ping our host. This patch adds options in Kconfig and Makefile to
build ping6 command.
Series-changes: 3
- Added structures and functions descriptions
- Added to ping6_receive() return value instead of void
Series-changes: 4
- Fixed structures and functions description style
Signed-off-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The command tftpboot uses IPv4 by default. Add the possibility to use IPv6
instead. If an address in the command is an IPv6 address it will use IPv6
to boot or if there is a suffix -ipv6 in the end of the command it also
force using IPv6. All other tftpboot features and parameters are left
the same.
Signed-off-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make it clear that if only 1 parameter is provided this is the duration.
The ISO symbol for hertz is Hz.
Fixes: c0c88533ff ("Sound: Add command for audio playback")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
eficonfig command reads all possible UEFI load options
from 0x0000 to 0xFFFF to construct the menu. This takes too much
time in some environment.
This commit uses efi_get_next_variable_name_int() to read all
existing UEFI load options to significantlly reduce the count of
efi_get_var() call.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Some commands need to enumerate the existing UEFI load
option variable("Boot####"). This commit transfers some code
from cmd/efidebug.c to lib/efi_loder/, then exposes
efi_varname_is_load_option() function to check whether
the UEFI variable name is "Boot####".
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Use u16_strsize() to simplify the u16 string buffer
size calculation.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The directory name in eficonfig menu entry contains the
'\' separator. strcmp() argument ".." is wrong and one directory
up handling does not work correctly. strcmp() argument must
include '\' separator.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
EFI_LOADER_DATA/CODE is reserved for EFI applications.
Memory allocated by U-Boot for internal usage should be
EFI_BOOT_SERVICES_DATA or _CODE or EFI_RUNTIME_SERVICES_DATA or _CODE.
Reported-by: François-Frédéric Ozog <ff@ozog.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: François-Frédéric Ozog <ff@ozog.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This commit adds a simple wget command that can download files
from http server.
The command syntax is
wget ${loadaddr} <path of the file from server>
Signed-off-by: Duncan Hare <DuncanCHare@yahoo.com>
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
It seems this symbol was missed when renaming DM_VIDEO -> VIDEO. Update
it.
Fixes: b86986c7b3 ("video: Rename CONFIG_DM_VIDEO to CONFIG_VIDEO")
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: John Keeping <john@metanate.com>
Return value -1 cause U-Boot to print usage message. Return value
1 (CMD_RET_FAILURE) indicates failure. So fix return value when ubifs
command starts it execution and fails.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Always increment both the iterator and pointer into the string
property value by length of the current element + 1 (to cater
for the string delimiter), otherwise the element extracted from
the string property value would be extracted from an offset that
is multiple of the length of the first element, instead of sum
of element lengths until select index.
This fixes 'fdt get value' operation for index above 1 (counting
from index 0).
Acked-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Fixes: 13982ced2c ("cmd: fdt: Add support for reading stringlist property values")
Signed-off-by: Marek Vasut <marex@denx.de>
This commit adds the menu-driven interface to show the
signature list content.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This commit adds the menu-driven UEFI Secure Boot Key
enrollment interface. User can enroll PK, KEK, db
and dbx by selecting file.
Only the signed EFI Signature List(s) with an authenticated
header, typically '.auth' file, is accepted.
To clear the PK, KEK, db and dbx, user needs to enroll the null key
signed by PK or KEK.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
EFI_SIMPLE_FILE_SYSTEM_PROTOCOL is not always provided
by U-Boot. Use protocol interface functions instead of
U-Boot internal functions.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Following commits are adding support for UEFI variable management
via the eficonfig menu. Those functions needs to use
eficonfig_create_device_path() to construct the full device path
from device path of the volume and file path, so move it
out of their static declarations.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
All the eficonfig menus other than "Change Boot Order"
use 'eficonfig_entry' structure for each menu entry.
This commit refactors change boot order implementation
to use 'eficonfig_entry' structure same as other menus
to have consistent menu handling.
This commit also simplifies the data->active handling when
KEY_SPACE is pressed, and sizeof() parameter.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Following commits are adding support for UEFI variable management
via the eficonfig menu. Those functions needs to use
append_entry() and append_quit_entry() to construct the
menu, so move them out of their static declarations.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
eficonfig_select_file_handler() is commonly used to select the
file. eficonfig_display_select_file_option() adds an additional
menu to clear the selected file.
eficonfig_display_select_file_option() is not always necessary
for the file selection process, so it must be outside of
eficonfig_select_file_handler().
This commit also renames the following functions to avoid confusion.
eficonfig_select_file_handler() -> eficonfig_process_select_file()
eficonfig_select_file() -> eficonfig_show_file_selection()
eficonfig_display_select_file_option() -> eficonfig_process_show_file_option()
Finally, test_eficonfig.py need to be updated to get aligned with
the above modification.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The 'ret' variable must be initialized before use
in eficonfig_delete_invalid_boot_option().
Fixes: c416f1c0bc ("bootmenu: add removable media entries")
Addresses-Coverity: 376207 ("Uninitialized variables")
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Goto for an immediately succeeding label is superfluous.
Fixes: 87d791423a ("eficonfig: menu-driven addition of UEFI boot option")
Addresses-Coverity: 376202 ("Identical code for different branches")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This converts the following to Kconfig:
CONFIG_SYS_LOADS_BAUD_CHANGE
CONFIG_LOADS_ECHO
As part of this, we move CMD_SAVES to be after CMD_LOADS as they are
logically related (load or save an s-record format file) and this makes
grouping of CONFIG_SYS_LOADS_BAUD_CHANGE easier.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update the sandbox implementation to use UCLASS_HOST and adjust all
the pieces to continue to work:
- Update the 'host' command to use the new API
- Replace various uses of UCLASS_ROOT with UCLASS_HOST
- Disable test_eficonfig since it doesn't work (this should have a unit
test to allow this to be debugged)
- Update the blk test to use the new API
- Drop the old header file
Unfortunately it does not seem to be possible to split this change up
further.
Signed-off-by: Simon Glass <sjg@chromium.org>
On 64-bit platforms where int is 32-bit wide, the eeprom command
parse_numeric_param() routine truncates the memory address parameter to
the lower 32-bit. Make parse_numeric_param() return long to allow
read/write of addresses beyond the lower 4GB.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
A hlist is headed by just a single pointer, so can only be traversed
forwards, and insertions can only happen at the head (or before/after
an existing list member). But each list node still consists of two
pointers, so arbitrary elements can still be removed in O(1).
This is precisely what we need for the cyclic_list - we never need to
traverse it backwards, and the order the callbacks appear in the list
should really not matter.
One advantage, and the main reason for doing this switch, is that an
empty list is represented by a NULL head pointer, so unlike a
list_head, it does not need separate C code to initialize - a
memset(,0,) of the containing structure is sufficient.
This is mostly mechanical:
- The iterators are updated with an h prefix, and the type of the
temporary variable changed to struct hlist_node*.
- Adding/removing is now just hlist_add_head (and not tail) and
hlist_del().
- struct members and function return values updated.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Tim Harvey <tharvey@gateworks.com> # imx8mm-venice-*
Add a command to read the metadata as specified in the FWU
specification and print the fields of the metadata.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Etienne Carriere <etienne.carriere@linaro.org>
The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE
and this makes it imposible to use CONFIG_VAL().
Rename it to resolve this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
- simplefb rotation support
- support splash as raw image from MMC
- enhancements to Truetype console (multiple fonts and sizes)
- drop old LCD support
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCY17nfA4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXPPoAJ0UYyt3kwslUlAJhOC+KU9UlYnVuwCbBXIQyBua
K5clq+GyxXfaDl2Hnvc=
=XXVp
-----END PGP SIGNATURE-----
Merge tag 'video-20221030' of https://source.denx.de/u-boot/custodians/u-boot-video
- fix [hv]sync active vs back porch in dw_mipi_dsi
- simplefb rotation support
- support splash as raw image from MMC
- enhancements to Truetype console (multiple fonts and sizes)
- drop old LCD support
This option should not have the SYS_ in it. Drop it so it fits in with the
other video options.
Also simplify the alignment code in gunzip_bmp(), since malloc() always
returns a 32-bit-aligned pointer.
Signed-off-by: Simon Glass <sjg@chromium.org>
The bmp command already has a way to centre the image. Using this CONFIG
option to also centre it makes it impossible to control where images are
placed on the screen. Drop the extra check.
Simplify the Kconfig file we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a new 'font' command which allows the fonts to be listed as well as
selecting a different font and size.
Allow the test to run on sandbox, where multiple font/size combinations
are supported, as well as sandbox_flattree, where they are not.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is enabled for LCD but not for VIDEO. Enable it since it is useful
to be able to clear the screen and adds very little code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move these commands and the implementation to the cmd/ directory, which is
where most commands are kept.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
[agust: keep vidconsole_position_cursor() in vidconsole uclass]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
uclass_first_device/uclass_next_device return value will be removed,
don't use it.
With the current implementation dev is equivalent to !ret. It is
redundant to check both, ret check can be replaced with dev check, and
ret check inside the iteration is dead code.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently the 'sf update' command fails in case the 'start' offset is
not aligned to SPI NOR erase block size. Add the missing alignment
calculation. In case the start offset is in the middle of erase block,
round start address down to the nearest aligned one, compare only the
updated data between what is in the SPI NOR and what is being written,
copy new data at offset of the compare buffer, and write back the entire
erase block.
This is useful e.g. on i.MX6Q where the u-boot-with-spl.imx is at
offset 0x400 in the SPI NOR, while the SPI NOR may have erase block
size e.g. 0x1000 bytes.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
For some blk operations, it's possible that a different hw partition
gets selected via blk_dselect_hwpart().
In that case, only the region of the device covered by that partition
is accessible.
This breaks "bcb load" which attempts to read the gpt and assumes it's
on the user(0) hw partition:
=> bcb load 2 misc
GUID Partition Table Header signature is wrong: 0xDE7B17AD07D9E5D6 != 0x5452415020494645
find_valid_gpt: *** ERROR: Invalid GPT ***
GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645
find_valid_gpt: *** ERROR: Invalid Backup GPT ***
Error: mmc 2:misc read failed (-2)
Add a fail-safe in __bcb_load() to ensure we will always read from the
user(0) hwpartition.
This fixes the following fastboot sequence:
$ fastboot erase mmc2boot1 # switch to hwpart1
$ fastboot reboot bootloader # switch to hwpart0, then reads GPT
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
When we try to load a kernel via the QEMU firmware device, we currently
"return -1;" if no kernel was specified on the QEMU command line. This
leads to the usage output, which is confusing (since nothing on the
command line was really wrong), but also somewhat hides the actual error
message.
Return CMD_RET_FAILURE (1), as it's a proper error, and make the message
more clear that this is not only a "warning".
This helps to call this command in boot scripts, and to gracefully
continue if this doesn't work.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
At the moment the QEMU firmware command just prints the size of the
loaded binaries on the console.
To go with all the other load methods, and many boot scripts'
expectations, also store the size of the file loaded last in the
environment variable "filesize".
We first put the kernel size in there, but overwrite this with the
initrd size, should we have one, because this is probably the more
prominent user of $filesize (in the booti or bootz command).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Adds an "ncsi" command to manually start NC-SI configuration.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Beside some rather unexciting sync of the DTs from the kernel tree, and
some Kconfig cleanup, there are some improvements for the ARMv5 Allwinner
family, to support boards with the F1C200s (64MB DRAM) better. We will
get actual board support as soon as the DTs have passed the Linux review
process.
There is also support for the X96 Mate TV Box, featuring the H616 SoC and
a full 4GB of DRAM.
Also we found the secret to enable SPI booting on the H616 (pin PC5 must
be pulled to GND), so the SPI boot support patch is now good to go.
Passed the gitlab CI, plus briefly tested on Pine64-LTS, LicheePi Nano,
X96 Mate and OrangePi Zero.
In the sbi command use the same short texts for the legacy extensions
as the SBI specification 1.0.0.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Rick Chen <rick@andestech.com>
If calling 'Get SBI specification version' fails, write an error message
and return CMD_RET_FAILURE.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The SBI command can print out the version number of the SBI implementation.
Choose the correct output format for RustSBI.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Some configuration symbols formerly defined in header files were
recently converted to Kconfig symbols. This moved their value definition
into *every* defconfig file, even though those values are hardly board
choices.
Use the new Kconfig option to define per-SoC default values, in just one
place, which makes the definition in each defconfig file redundant.
We refrain from setting a sunxi specific value for CONFIG_SYS_BOOTM_LEN,
so this defaults to a much better 64MB for uncompressed arm64 kernels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The working FDT is the one which comes from the OS and is fixed up by
U-Boot. When the bootm command runs, it sets up the working FDT to be the
one it is about to pass to the OS, so that fixups can happen.
This seems like an important step, so add a message indicating that the
working FDT has changed. This is shown during the running of the bootm
command.
Signed-off-by: Simon Glass <sjg@chromium.org>
Functions which implement commands must return a CMD_RET_... error code.
At present bootm can return a negative errno value in some cases, thus
causing strange behaviour such as trying to exit the shell and printing
usage information.
Fix this by returning the correct value.
Signed-off-by: Simon Glass <sjg@chromium.org>
There are a few commands that iterate uclass with
uclass_first_device/uclass_next_device or the _err variant.
Use the _check class iterator variant to get devices that fail to probe
as well, and print the status.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Loadfile2 code is installing two protocols on it's own handle
and uses efi_delete_handle() to clean it up on failure(s). However
commit 05c4c9e21a ("efi_loader: define internal implementations of
install/uninstallmultiple") prepares the ground for us to clean up
efi_delete_handle() used in favor of Install/UninstallMultipleProtocol.
While at it clean up the non needed void casts to (void *) on the
protolcol installation.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
* don't use EFI_CALL() for variable services
* don't use runtime pointer to access exported function
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
To allow easily iterate over all UBI volumes, add a new command which
either print all user UBI volumes on output or set them into env variable.
As UBI volumes can have arbitrary name/label, in most cases it is useful to
iterate them by their numbers. This can be achieved by -numeric flag.
This functionality is similar to already existing 'part list' command which
prints partitions on formatted block device.
Signed-off-by: Pali Rohár <pali@kernel.org>
Currently, there is no way for users to check the readings from thermal
sensors from U-boot console, only some boards print it during boot.
So, lets add a simple "temperature" command that allows listing thermal
uclass devices and getting their value.
Note that the thermal devices are intenionally probed if list is used as
almost always they will not get probed otherwise and there is no way for
users to manually call probe on a certain device from console.
Assumption is made that temperature is returned in degrees C and not
milidegrees like in Linux as this is what most drivers seem to return.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add xxd command to print file content as hexdump to standard out
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Roger Knecht <rknecht@pm.me>
When host issues "fastboot reboot fastboot", it's expected that the
board drops the USB connection before resetting.
On some boards, such as Khadas VIM3L and SEI610, this is not the case.
We observe the following error:
$ fastboot reboot fastboot
Rebooting into fastboot OKAY [ 0.004s]
fastboot: error: Failed to boot into userspace fastboot; one or more components might be unbootable.
This does not happen when we use the RST button on the board.
It can be reproduced in linux with:
# echo b > /proc/sysrq-trigger
In this case, we hit a undefined hardware behavior, where D+ and D-
are in an unknown state. Therefore the host can't detect usb
disconnection.
Make sure we always call usb_gadget_release() when a "fastboot reboot"
command is issued.
Note: usb_gadget_release() should be called before g_dnl_unregister()
because g_dnl_unregister() triggers a complete() call on each
endpoint (thus calling do_reset()).
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
The cls command works fine on the serial console. There is no reason to
let it depend on the availability of video.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
In general handles should only be deleted if the last remaining protocol
is removed. Instead of explicitly calling
efi_create_handle -> efi_add_protocol -> efi_delete_handle which blindly
removes all protocols from a handle before removing it, use
InstallMultiple/UninstallMultiple which adheres to the EFI spec and only
deletes a handle if there are no additional protocols present
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Currently we have subcommands 'efidebug dh' which shows protocols per
handle and 'efidebug devices' which shows the device path. None shows which
U-Boot device matches the handle.
Change 'efidebug dh' to show the device path and the U-Boot device if any
is associated with the handle.
Remove 'efidebug devices'.
Old output of 'efidebug dh':
Handle Protocols
================ ====================
000000001b22e690 Device Path, Block IO
000000001b22e800 Device Path, Block IO, system, Simple File System
New output of 'efidebug dh':
000000001b22e690 (host0)
/VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/VenHw(bbe4e671-5773-4ea1-9aab-3a7dbf40c482,00)
Block IO
000000001b22e800 (host0:1)
/VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/VenHw(bbe4e671-5773-4ea1-9aab-3a7dbf40c482,00)/HD(1,GPT,7e5c17c5-3f5f-49d0-ae96-511b21d7f273,0x800,0x3f7df)
Block IO
system
Simple File System
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This is not needed and we should avoid typedefs. Use the struct instead
and rename it to indicate that it really is a legacy struct.
Signed-off-by: Simon Glass <sjg@chromium.org>
In a lot of cases kernel resets UART HW. To ensure that U-Boot messages
printed before booting the kernel are not lost, call new U-Boot console
flush() function.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Changing baudrate is a sensitive operation. To ensure that U-Boot messages
printed before changing baudrate are not lost, call new U-Boot console
flush() function.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The fdt command currently handles stringlists as strings in 'fdt get value'
subcommand. Since strings in FDT stringlists are separated by '\0', only
the first value gets inserted into the environment variable passed to the
'fdt get value' command.
Example, consider the following DT snippet:
/ { compatible = "foo", "bar" };
The following command only reports the first string in stringlist:
=> fdt get value var / compatible ; print var
foo
It is not possible to assign list of null-terminated strings into U-Boot
environment variable. Add optional 'index' parameter to the subcommand
'fdt get value <var> <path> <prop> [<index>]' which lets user specify which
string within the stringlist should be assigned into the 'var' variable.
The default value of 'index' is 0 in case it is not present. This way the
'fdt' command API does not change and existing scripts are not broken.
The following command now reports the Nth string in stringlist, counting
from zero:
=> fdt get value var / compatible 1 ; print var
bar
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Globally replace all occurances of WATCHDOG_RESET() with schedule(),
which handles the HW_WATCHDOG functionality and the cyclic
infrastructure.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
We currently have an if_type (interface type) and a uclass id. These are
closely related and we don't need to have both.
Drop the if_type values and use the uclass ones instead.
Maintain the existing, subtle, one-way conversion between UCLASS_USB and
UCLASS_MASS_STORAGE for now, and add a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
This condition is not needed for these commands, since BLK is enabled for
all boards which use block devices and commands are not available in SPL,
so even if SPL_BLK is not enabled, it doesn't affect commands.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now when loadx and loady commands could be aborted / cancelled by CTRL+C,
allow to configure timeout for initial x/y-modem packet via env variable
$loadxy_timeout and by default use value from new compile-time config
option CONFIG_CMD_LOADXY_TIMEOUT. Value is in seconds and zero value means
infinite timeout. Default value is 90s which is the value used before this
change for loadx command.
Other load commands loadb and loads already waits infinitely. Same behavior
for loadx and loady commands can be achieved by setting $loadxy_timeout or
CONFIG_CMD_LOADXY_TIMEOUT to 0.
Signed-off-by: Pali Rohár <pali@kernel.org>
UEFI:
Implement a command eficonfig to maintain Load Options and boot order via
menus.
-----BEGIN PGP SIGNATURE-----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=P89S
-----END PGP SIGNATURE-----
Merge tag 'efi-next-2022-09-14' of https://source.denx.de/u-boot/custodians/u-boot-efi into next
Pull request for efi next
UEFI:
Implement a command eficonfig to maintain Load Options and boot order via
menus.
This commit adds the menu entry to update UEFI BootOrder variable.
User moves the entry with UP/DOWN key, changes the order
with PLUS/MINUS key, press SPACE to activate or deactivate
the entry, then finalizes the order by ENTER key.
If the entry is activated, the boot index is added into the
BootOrder variable in the order of the list.
The U-Boot menu framework is well designed for static menu,
this commit implements the own menu display and key handling
for dynamically change the order of menu entry.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
UEFI specification requires booting from removal media using
a architecture-specific default image name such as BOOTAA64.EFI.
This commit adds the removable media entries into bootmenu,
so that user can select the removable media and boot with
default image.
The bootmenu automatically enumerates the possible bootable
media devices supporting EFI_SIMPLE_FILE_SYSTEM_PROTOCOL,
add it as new UEFI boot option(BOOT####) and update BootOrder
variable. This automatically generated UEFI boot option
has the dedicated guid in the optional_data to distinguish it from
the UEFI boot option user adds manually. This optional_data is
removed when the efi bootmgr loads the selected UEFI boot option.
This commit also provides the BOOT#### variable maintenance feature.
Depending on the system hardware setup, some devices
may not exist at a later system boot, so bootmenu checks the
available device in each bootmenu invocation and automatically
removes the BOOT#### variable corrensponding to the non-existent
media device.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
This commit adds the menu entry to delete the UEFI boot option.
User moves the entry with UP/DOWN key, changes, then presses
ENTER key to delete the selected boot option.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
This commit adds the menu entry to edit the existing
BOOT#### variable contents.
User selects the item from the boot option list, then
user can edit the description, file path and optional_data.
Note that automatically generated boot option entry by bootmenu
to support the removable media device is filtered out and user
can not edit the automatically generated entry.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
This commit add the "eficonfig" command.
The "eficonfig" command implements the menu-driven UEFI boot option
maintenance feature. This commit implements the addition of
new boot option. User can select the block device volume having
efi_simple_file_system_protocol and select the file corresponding
to the Boot#### variable. User can also enter the description and
optional_data of the BOOT#### variable in utf8.
This commit adds "include/efi_config.h", it contains the common
definition to be used from other menus such as UEFI Secure Boot
key management.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
This patch adds the cyclic command, which currently only supports the
'list' subcommand, to list all currently registered cyclic functions.
Here an example:
=> cyclic list
function: cyclic_demo, cpu-time: 7010 us, frequency: 99.80 times/s
function: cyclic_demo2, cpu-time: 1 us, frequency: 1.13 times/s
As you can see, the cpu-time is accounted, so that cyclic functions
that take too long might be discovered. Additionally the frequency is
logged.
The 'cyclic demo' commands registers the cyclic_demo() function to
be executed all 'cycletime_ms' milliseconds. The only thing this
function does is delaying by 'delay_us' microseconds.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add bdinfo_print_size() helper to display size variables (such as cache
sizes) in bdinfo format. The size is printed as "xxx Bytes", "xxx KiB",
"xxx MiB", "xxx GiB", etc as needed;
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Reviewed-by: Jason Liu <jason.hui.liu@nxp.com>
Link: https://lore.kernel.org/r/20220829170205.1274484-3-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
For obvious reasons BootROMS rejects unsigned images when secure boot is
enabled in OTP secure bits. So check for OPT secure bits and do not allow
flashing unsigned images when secure boot is enabled. Access to OTP via
U-Boot fuse API is currently implemented only for A38x and A37xx SoCs.
Additionally Armada 3700 BootROM rejects signed trusted image when secure
boot is not enabled in OTP. So add also check for this case. On the other
hand Armada 38x BootROM acceps images with secure boot header when secure
boot is not enabled in OTP.
OTP secure bits may have burned also boot device source. Check it also and
reject flashing images to target storage which does not match OTP.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Currently for A38x image is checked only header checksum.
So check also for image data checksum to prevent flashing broken image.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The command's name is a misnomer.
The command loads a file but does not run (boot) it.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Calling tftpput with less than 2 arguments must lead to a failure.
If tftpput is called with two arguments, these are the address and
the size of the file to be transferred.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the FIT loading process of the fpga command to use
fit_get_data_node.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Format the KVM implementation number in a human readable form.
With the patch output of the sbi command for Linux 5.19.1 looks like:
=> sbi
SBI 0.3
KVM 5.19.1
Machine:
Vendor ID 0
Architecture ID 7005c
Implementation ID 7005c
Extensions:
SBI Base Functionality
Timer Extension
IPI Extension
RFENCE Extension
Hart State Management Extension
System Reset Extension
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
It is useful to read information about the current TPM state, where
supported, e.g. for debugging purposes when verified boot fails.
Add support for this to the TPM interface as well as Cr50. Add a simple
sandbox test.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This feature is used for measured boot, so we can add a log entry to the
TCPA with some information about where the digest comes from. It is not
currently supported in the TPM drivers, but add it to the API so that
code which expects it can signal its request.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This command is being introduced with the goal of allowing user-friendly
"generic use case" U-Boot builds to pause until user input under some
situations.
The main use case would be when a boot failure happens, to pause until
the user has had time to acknowledge the current state.
Tested using:
make && ./u-boot -v -T -c 'ut lib lib_test_hush_pause'
Signed-off-by: Samuel Dionne-Riel <samuel@dionne-riel.com>
Cc: Simon Glass <sjg@chromium.org>
fit_image_get_comp() should not set value -1 in case it can't read
the compression node. Instead, leave the value untouched in that case
as it can be absent and a default value previously defined by the
caller of fit_image_get_comp() should be used.
As a result the warning message
WARNING: 'compression' nodes for ramdisks are deprecated, please fix your .its file!
no longer shows if the compression node is actually absent.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This reinstates fix from commit 8f8c04bf1e ("i2c: fix stack buffer
overflow vulnerability in i2c md command") without the changes unrelated
to the actual fix. Avoid the underflow by setting only nbytes and
linebytes as unsigned integers.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Nicolas Iooss <nicolas.iooss+uboot@ledger.fr>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tim Harvey <tharvey@gateworks.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
This reverts commit 8f8c04bf1e.
The commit is largely wrong and breaks most of i2c command functionality.
The problem described in the aforementioned commit commit message is valid,
however the commit itself does many more changes unrelated to fixing that
one problem it describes. Those extra changes, namely the handling of i2c
device address length as unsigned instead of signed integer, breaks the
expectation that address length may be negative value. The negative value
is used by DM to indicate that address length of device does not change.
The actual bug documented in commit 8f8c04bf1e
can be fixed by extra sanitization in separate patch.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Nicolas Iooss <nicolas.iooss+uboot@ledger.fr>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
other minor fixes
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmMJZZ8RHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZ8pggAjYxdCTEtTMJamt67hht8xjeZLom4KX3G
HZJhXHAXHgnw2vku4nYKEZp6B5+if184I34Gbw6AGHJib7tfGBPFHeb0lIg+NHlB
bb7hMSKJwZJAASWB5Txqtmx2iFdnTZVnUUMp5Jl8Fpd0yhd8YxsaDKrt7BUTTZgM
84ht/zv+laFoDvM0Xj81TVkPym8ShIylsUc44Sn8je5KC8kg1lmukqnBHAOj0DKG
cE/hGOmdq5HLu7Ylj3XQ8tl6jpPMn6hltoIMku6ePsJeaTOdsXg2i3RN/Xga835D
7/KW+qasl2+5XwqYyAXjLW6YncbGzxmsLfJ6HrzInLtp9rkOt/z0hA==
=09Bs
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-26aug22' of https://source.denx.de/u-boot/custodians/u-boot-dm
binman/patman documentation improvements
other minor fixes
Avoid enabling this command by default. This saves about 1KB of code
space.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
PCIe config space has address range 0-4095. So do not allow reading from
addresses outside of this range. Lot of U-Boot drivers do not expect that
passed value is not in this range. PCI DM read function is extended to
fill read value to all ones or zeros when it fails as U-Boot callers
ignores return value.
Calling U-Boot command 'pci display.b 0.0.0 0 0x2000' now stops printing
config space at the end (before 0x1000 address).
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Currently message is not intended that prompt end up at the end of debug
line. For example like this:
DFU alt info setting: done
DFU entities configuration failed!
(partition table does not match dfu_alt_info?)
Firmware update failed: <NULL>
Cannot handle a capsule at 10000000Zynq>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Add support for handling this concept in bootflows. Update the 'bootflow'
command to allow only the normal bootmeths to be used. This alllows
skipping EFI bootmgr and VBE, for example.
Signed-off-by: Simon Glass <sjg@chromium.org>
With global bootmeths we want to scan without a bootdev. Update the logic
to allow this.
Change the bootflow command to show the bootdev only when valid.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current way of handling things like EFI bootmgr is a bit odd, since
that bootmeth handles selection of the bootdev itself. VBE needs to work
the same way, so we should support it properly.
Add a flag that indicates that the bootmeth is global, rather than being
invoked on each bootdev. Provide a helper to read a bootflow from the
bootmeth.
Signed-off-by: Simon Glass <sjg@chromium.org>
We want to use VBE to mean Verfiied Boot for Embedded in U-Boot. Rename
the existing VBE (Vesa BIOS extensions) to allow this.
Verified Boot for Embedded is documented doc/develop/vbe.rst
Signed-off-by: Simon Glass <sjg@chromium.org>
Remove the dependency on CMD_PXE from BOOTMETH_DISTRO by introducing a
new hidden kconfig symbol to control whether pxe_utils is compiled,
allowing bootstd's distro method to be compiled without needing
networking support enabled.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Correct build errors when CMD_BOOTM is not enabled:
Signed-off-by: Simon Glass <sjg@chromium.org>
A large number of files include <flash.h> as it used to be how various
SPI flash related functions were found, or for other reasons entirely.
In order to migrate some further CONFIG symbols to Kconfig we need to
not include flash.h in cases where we don't have a NOR flash of some
sort enabled. Furthermore, in cases where we are in common code and it
doesn't make sense to try and further refactor the code itself in to new
files we need to guard this inclusion.
Signed-off-by: Tom Rini <trini@konsulko.com>
If 'extension apply all' is executed and no extension is found, the return
value of do_extension_apply() is undefined. Return CMD_RET_FAILURE in this
case.
Fixes: 2f84e9cf06 ("cmd: add support for a new "extension" command")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
The source code contains an error:
- argv[2] contains <channel> arg, variable for env_set is in argv[3]
- number of args is 4
Revert 54d24d7260
cmd: simplify do_adc_single()
Fixes 9de612ae4d
cmd: adc: Add support for storing ADC result in env variable
Reviewed-by: Simon Glass <sjg@chromium.org>
The 'rng' command dumps a number of random bytes on the console. Add a
set of tests for the 'rng' command. The test function performs basic
sanity testing of the command.
Since a unit test is being added for the command, enable it by default
in the sandbox platforms.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Use a statically allocated buffer on stack instead of using malloc for
reading the random bytes. Using a local array is faster than
allocating heap memory on every initiation of the command.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The 'rng' u-boot command is used for printing a select number of
random bytes on the console. Currently, the RNG device from which the
random bytes are read is fixed. However, a platform can have multiple
RNG devices, one example being qemu, which has a virtio RNG device and
the RNG pseudo device through the TPM chip.
Extend the 'rng' command so that the user can provide the RNG device
number from which the random bytes are to be read. This will be the
device index under the RNG uclass.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Negative return value from cmd main function cause U-Boot to print criplic
error message: exit not allowed from main input shell.
Set return value on error to 1.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Armada 3700 BootROM supports also images with sha512 checksums and
mox-imager tool [1] generates such bootable images. Without sha512 support
U-Boot bubt command just prints error message:
Error: Unsupported hash_algorithm_id = 64
Error: Image header verification failed
This patch adds support for sha512 checksum validation for Armada 3700
images. With it bubt prints:
Image checksum...OK!
[1] - https://gitlab.nic.cz/turris/mox-boot-builder.git
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
net_loop() returns signed int type and negative value represents error.
tftp_read_file() returns unsigned size_t type and zero value represents
error. Casting signed negative value to unsigned size_t type cause losing
information about error and bubt thinks that no error happened, and
continue erasing SPI-NOR which cause malfunction device.
Fix this issue by correctly propagating failure during tftp transport.
With this change when there is no eth link, bubt does not erase SPI-NOR
anymore.
=> bubt
Burning U-Boot image "flash-image.bin" from "tftp" to "spi"
ethernet@30000 Waiting for PHY auto negotiation to complete......... TIMEOUT !
ethernet@30000: No link.
Error: Failed to read file flash-image.bin from tftp
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Current image type verification code is specific to 32-bit Armada SoCs but
used only for Armada 38x. Implement image type verification for Armada 3700
and enable Armada 38x image verification for all 32-bit Armada SoCs.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
add arguments for mmc wp to assign which boot partition to protect.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
These flags may be used to check whether an FPGA driver is able to
load a particular FPGA bitstream image.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Tested-by: Ricardo Salveti <ricardo@foundries.io>
Tested-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Link: https://lore.kernel.org/r/20220722141614.297383-7-oleksandr.suvorov@foundries.io
Signed-off-by: Michal Simek <michal.simek@amd.com>
It allows using this feature without enabling the "fpga loads"
command.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Co-developed-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Tested-by: Ricardo Salveti <ricardo@foundries.io>
Tested-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Link: https://lore.kernel.org/r/20220722141614.297383-2-oleksandr.suvorov@foundries.io
Signed-off-by: Michal Simek <michal.simek@amd.com>
Fix diacritics in some instances of my name and change my e-mail address
to kabel@kernel.org.
Add corresponding .mailmap entries.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Do not suggest successful operation if a flash area to be changed is
actually locked, thus will not execute the request. Rather report an
error and bail out. That's way more user-friendly than asking them to
manually check for this case.
Derived from original patch by Chao Zeng.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
efi_dp_str() allocates memory which should be released after use.
Use %pD printf code. Adjust message wording.
Fixes: d837cb1e3b ("efi: Add debugging to efi_set_bootdev()")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This converts the following to Kconfig:
CONFIG_SYS_BOOTM_LEN
As part of this, rework error handling in boot/bootm.c so that we pass
the buffer size to handle_decomp_error as CONFIG_SYS_BOOTM_LEN will not
be available to host tools but we do know the size that we passed to
malloc().
Cc: Soeren Moch <smoch@web.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
The "autoload" environment variable is always checked with env_get_yesno
as it can be set to any form of no. The default behavior of
env_get_yesno is to return -1 on variables that are not set, which acts
as true in general (we test for non-zero return). To convert
CONFIG_SYS_AUTOLOAD to Kconfig, given that it was almost always used to
set autoload to no, first rename to CONFIG_SYS_DISABLE_AUTOLOAD for
consistency sake. Then, make it so that if enabled we set autoload=0 in
the default environment. Migrate all platforms which set
CONFIG_SYS_AUTOLOAD to non-true or that set autoload to false in their
default environment to using CONFIG_SYS_DISABLE_AUTOLOAD
Signed-off-by: Tom Rini <trini@konsulko.com>
