To enable video driver at SPL, need to compile video-uclass,
vidconsole-uclass, backlight-uclass, panel-uclass, simple-panel, add
rules to compile them at SPL and u-boot proper. To support
splash_display at SPL, need to compile video-bmp, add rule to compile at
SPL and u-boot proper.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Compile video driver at SPL using CONFIG_SPL_VIDEO.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # qemu-x86_64
Add Kconfigs which enable the video driver and splash screen at SPL
stage only and not at u-boot proper. The existing Kconfigs from u-boot
proper were not used to make SPL splash screen independent to them.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Makes it possible to use e.g mcu_spi0 for custom board detection.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
For setting up the master firewalls present in the K3 SoCs, the arm64
clusters need to be powered on.
Re-locates the code for atf/optee authentication.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Configuring master firewalls require the power of the cluster to be
enabled before configuring them, change the load of rproc to configure
the gtc clocks and start the cluster along with configuring the boot
vector.
The start of rproc will only start the core.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
This matches AM64 and J721e and removes the need to forward
declare k3_spl_init(), k3_mem_init(), and check_rom_loaded_sysfw()
in sys_proto.h.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
These probably should be in some system wide header given their use.
Until then move them out of K3 sys_proto.h so we can finish cleaning
that header out.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This matches how it was done for pre-K3 TI platforms and it allows
us to move the forward declaration out of sys_proto.h.
It also removes the need for K3_BOARD_DETECT as one is free to simply
override the weak function in their board files as needed.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This header is only used locally by K3 init files, no need to have it
up with the global mach includes. Move into local includes.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This function is the same for each device when it needs to shutdown
the R5 core. Move this to the common section and move the remaining
device specific ID list to the device hardware include.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
The J7200 EVM will not include this file, this J7200 checks look
to be a copy/paste errora from j721e_evm.h, which J7200 *can* include.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
The TARGET_x_R5_EVM check is already enough to limit these defines to
only the correct builds. Remove the extra outer check.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
The K3 JTAG and SoC ID information is already stored in the K3 arch
hardware file, include that and use its definitions here.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This belongs in the J721e specific file as it is the only place
this is used. Any board level users should use the SOC driver.
While here, move the J721e and J7200 SoC IDs out of sys_proto.h
and into hardware.h. Use a macro borrowed from Rockchip and add
the rest of the SoC IDs for completeness and later use.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
The MSMC fixup is something we do based on SoC, not based on the board.
So this fixup does not belong in the board files. Move this to the
mach-k3 common file so that it does not have to be done in each board
that uses these SoCs.
We use ft_system_setup() here instead of ft_board_setup() since it is no
longer board level. Enable OF_SYSTEM_SETUP in the configurations that use
this to keep functionality the same.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This reverts commit 5717294230. This
does not exist in upstream kernel.org and breaks boot on DRA7-EVMs.
Drop the same.
Signed-off-by: Andrew Davis <afd@ti.com>
This is a collection of all the whitespace, renames, comment, and other
changes that should not change the DT functionality from Linux v6.3-rc6.
Signed-off-by: Andrew Davis <afd@ti.com>
This is a collection of all the whitespace, renames, comment, and other
changes that should not change the DT functionality from Linux v6.3-rc6.
Signed-off-by: Andrew Davis <afd@ti.com>
This is a collection of all the whitespace, renames, comment, and other
changes that should not change the DT functionality from Linux v6.3-rc6.
Signed-off-by: Andrew Davis <afd@ti.com>
This is a collection of all the whitespace, renames, comment, and other
changes that should not change the DT functionality from Linux v6.3-rc6.
Signed-off-by: Andrew Davis <afd@ti.com>
This is a collection of all the whitespace, renames, comment, and other
changes that should not change the DT functionality from Linux v6.3-rc6.
Signed-off-by: Andrew Davis <afd@ti.com>
Several DTS files have been updated in the Linux kernel with a new
PADCONF macro replacing the IOPAD version. Sync for the same here.
Signed-off-by: Andrew Davis <afd@ti.com>
This member is used in series.MakeCcFile() so should be declared in the
Series class.
Add a declaration to silence the warning.
Signed-off-by: Simon Glass <sjg@chromium.org>
- Add rk3588 evb support;
- Update pinctrl for rk3568 and rk3588;
- Update rk3288 dts;
- Update mmc support for rk3568 and rk3588;
- Add rng support for rk3588;
- Add DSI support for rk3568;
- Some other misc fixes in dts, config, driver;
- watchdog: arm_smc_wdt: add watchdog support (Lionel)
- watchdog: ftwdt010: return a previously deleted driver now ported to
DM (Sergei)
- watchdog: Add a watchdog driver for Raspberry Pi boards (Etienne)
