The ci_req->hw_buf can be NULL, test whether it is and if so,
avoid accessing it. Else, the system may crash.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Peter Chen <peter.chen@nxp.com>
Cc: Li Jun <jun.li@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
The imx8mm and imx8mn appear compatible with imx7d-usb
flags in the OTG driver. If the dr_mode is defined as
host or peripheral, the device appears to operate correctly,
however the auto host/peripheral detection results in an error.
The solution isn't just adding checks for imx8mm and imx8mn to
the check for imx7, because the USB clock needs to be running
to read from the USBNC_PHY_STATUS_OFFSET register or it will hang.
Marek requested that I not enable the clocks in ehci_usb_of_to_plat,
so I modified that function to return an unknown state if the
device tree does not explicitly state whether it is a host
or a peripheral.
When the driver probes, it looks to see if it's in the unknown
state, and only then will it read the register to auto-detect.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
In DFU v1.1 specification [1] the DFU_UPLOAD (Short Frame)
is handled only in dfuUPLOADIDLE state:
- Figure A.1 Interface state transition diagram
- the state description in chapter A.2
A.2.3 State 2 dfuIDLE
on Receipt of the DFU_UPLOAD request,and bitCanUpload = 1
the Next State is dfuUPLOADIDLE
A.2.10 State 9 dfuUPLOAD-IDLE
When the length of the data transferred by the device in response
to a DFU_UPLOAD request is less than wLength. (Short frame)
the Next State is dfuIDLE
In current code, when an UPLOAD is completely performed after the first
request (for example with wLength=200 and data read = 9), the DFU state
stay at dfuUPLOADIDLE until receiving a DFU_UPLOAD or a DFU_ABORT request
even it is unnecessary as the previous DFU_UPLOAD request already reached
the EOF.
This patch proposes to finish the DFU uploading (don't go to dfuUPLOADIDLE)
and completes the control-read operation (go to DFU_STATE_dfuIDLE) when
the first UPLOAD response has a short frame as an end of file (EOF)
indicator even if it is not explicitly allowed in the DFU specification
but this seems logical.
[1] https://www.usb.org/sites/default/files/DFU_1.1.pdf
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
binman support for bintools (binary tools)
minor tools improvements in preparation for FDT signing
various minor fixes and improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmHyEeYRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYYlgf8C7tQVklXz9ZHhxVrFaPHWwgmBzEZJSrc
7SWhDX9yBrAYBUk8Q4OMnJz6nXW8Rz5Td9GfBNWcJag1HjJqno4BxkqwGk2tshgj
GIY0D1cGfKJzB4E6/rK/ETwmX4KVUyEf7S2IdJ0oydkn9t7OwDkUX5WtGXo70E7q
ZJGYlX5NQCVBRAF9NYDuyVFljrPzAiyT58VCtXY3q63C7PmRYvag8r56ug+8lkk3
9EbOTcwETqq9SbT1vucyBxwbUmoKhb2BF32jEcIhozowIM3GNsSpkdzQCUnylqfa
LYI/p0oVTKLfFRBRvQjLgdB/OQP8MLkby8A++Db2OW49mBXhn/5JWA==
=PdpE
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-26jan22' of https://source.denx.de/u-boot/custodians/u-boot-dm
acpi refactoring to allow non-x86 use
binman support for bintools (binary tools)
minor tools improvements in preparation for FDT signing
various minor fixes and improvements
Add support for CDC ACM using the new UDC and gadget API. This protocol
can be used for serial over USB data transfer and is widely supported
by various OS (GNU/Linux, MS-Windows, OSX...). The usual purpose of
such link is to access device debug console and can be useful for
products not exposing regular UART to the user.
A default stdio device named 'usbacm' is created, and can be used
to redirect console to USB link over CDC ACM:
> setenv stdin usbacm; setenv stdout usbacm
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
This commit converts i.MX28's EHCI USB host driver to driver model
(DM_USB). It is a straightforward conversion (to reuse as much code
as possible), based on ehci-mx5.c code.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Those functions will be re-used when the ehci MXS driver (for imx28)
will be converted to also support CONFIG_DM_USB.
No functional changes introduced - only cosmetic changes (u32 type)
and alignment to pass checkpatch.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This function is going to be reused with the CONFIG_DM_USB enabled in
the imx28 mxs USB ehci driver.
No functional changes introduced.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
For whatever reason, usb_setup_ehci_gadget removes and probes USB device
0. However, not all systems have a device 0. Use the first device
instead.
The device probed should probably have something to do with the
controller (as specified by e.g. ums <controller> or fastboot
<controller>). In fact, I find it odd that we probe the USB device in
the first place, because this is just to set up the gadget itself.
Presumably, the controller should be probed by usb_gadget_initialize
somehow.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- fdt_support: Add fdt_for_each_node_by_compatible() helper macro
(Marek)
- turris_omnia: Fixup SATA or PCIe nodes at runtime in DT blob (Pali)
- pci_mvebu: Add support for Kirkwood PCIe controllers (Pali)
- SPL: More verifications for kwbimage in SPL (Pali)
- mvebu: Remove comphy_update_map() (Pali)
- Minor misc stuff
Add parameter spl_boot_device to spl_parse_board_header(), which allows
the implementations to see from which device we are booting and do
boot-device-specific checks of the image header.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Fix fastboot flash bug.
If the downloading file size is equal to the partition size, "fastboot
flash" can't work, at least in sunxi platform, because used an
uninitalized point: ep->desc.
This patch also fixed 'data abort' bug in am335x platform.
Reproduce: fastboot flash loader1 spl/sunxi-spl.bin.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Fastboot support has been broken on platforms using dwc2 controller
since the gadget gets its max packet size from it.
This patch is the equivalent of 723fd5668f which fixed the same issue
but for the chipidea controller.
Fixes: 27c9141b11 ("usb: gadget: fastboot: use correct max packet size")
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
This ensures the USB_MUSB_PIO_ONLY config is set to an apppropriate
value from the changes enabling USB_MUSB_GADGET does.
Namely, USB_MUSB_PIO_ONLY default to =y on USB_MUSB_SUNXI being y.
Signed-off-by: Samuel Dionne-Riel <samuel@dionne-riel.com>
Add support for the proper dwc3 device tree binding support as specified
in the offical device tree spec.
Initially, add support for the LS1028A support. Other SoCs should be
easy to add by just adding the corresponding compatible string.
Unfortunately, the device trees of all other layerscape SoCs are not
converted and uses a wrong compatible string only known in u-boot.
To maintain backwards compatibility with current u-boot device trees,
add the generic "fsl,layerscape-dwc3" compatible string.
OTG mode is not supported yet. The dr_mode in the devicetree will either
have to be set to peripheral or host.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
[backport from linux commit d9612c2f0449e24983a8b689603210486a930c90]
Enable the undefined length INCR burst type and set INCRx.
Different platform may has the different burst size type.
In order to get best performance, we need to tune the burst
size to one special value, instead of the default value.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
[backport from linux commit db2be4e9e30c6e43e48c5749d3fc74cee0a6bbb3]
Add adjust_frame_length_quirk for writing to fladj register
which adjusts (micro)frame length to value provided by
"snps,quirk-frame-length-adjustment" property thus avoiding
USB 2.0 devices to time-out over a longer run
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Both dr_mode and maximum-speed properties are usually optional. Drivers
will still try to fetch the properties nonetheless, which leads to error
messages, although they are no errors. Change pr_err() to pr_debug().
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The official ls1028a binding of the driver uses the following as
compatibles:
compatible = "fsl,ls1028a-dwc3", "snps,dwc3";
Change the ls1028a device tree and add this new compatible to the fsl
specific xhci driver, otherwise the generic dwc3 driver will be used
with the compatibles above.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When allocate the GPD ring, and tell its address to the controller, then
the driver starts or resumes the QMU, the controller will try to access
the first GPD, so need flush the first one to avoid wrong GPD status.
Reported-by: Xin Lin <Xin.Lin@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
dev_err seems to be moved to different header file. Include
dm/device_compat.h file to compile properly.
Fixes: 69dae8902b ("linux/compat.h: Remove redefinition of dev_xxx macros")
Signed-off-by: Stefan Agner <stefan@agner.ch>
On mvebu this is defined if and only if !ARM64.
Otherwise it is defined for boards with ARCH_MX23, ARCH_TEGRA and
ARCH_ZYNQ, and also for SOC_AR934X (tplink_wdr4300).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
This option is only used for
mx23evk_defconfig
mx23_olinuxino_defconfig
which are the only i.MX23 boards.
Add depend on ARCH_MX23 and default to y.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
In preparation for moving this option to Kconfig, rename it to be
consistent with other USB EHCI Kconfig options.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command
-----BEGIN PGP SIGNATURE-----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=S4kl
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20211012' of https://source.denx.de/u-boot/custodians/u-boot-stm
- Disable ATAGS for STM32 MCU and MPU boards
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command
Signed-off-by: Tom Rini <trini@konsulko.com>
Add usb_gadget_handle_interrupts(), usb_gadget_register_driver()
and usb_gadget_unregister_driver() to be able to test
binding usb gadget.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add an entry in usb_gadget_controller_number() for the DWC2
gadget controller. It is used to bind the USB Ethernet driver.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reported-by: Herbert Poetzl <herbert@13thfloor.at>
Cc: Marek Vasut <marex@denx.de>
Cc: Herbert Poetzl <herbert@13thfloor.at>
As part of migrating to DM_GPIO and DM_PINCTRL, eventually we will
remove the asm/arch/gpio.h header. In preparation, clean up the various
files that include it.
Some files did not contain any GPIO code at all, so this header was
completely unused.
A few files contained only legacy platform-specific GPIO code for
setting up pin muxes. They were left unchanged, as that code will be
completely removed by the DM_PINCTRL migration.
The remaining files contain some combination of DM_GPIO and legacy GPIO
code. For those, switch to including asm/gpio.h (if it wasn't included
already). Right now, this header provides both sets of functions,
because ARCH_SUNXI selects GPIO_EXTRA_HEADER. This will still be the
right header to include once the DM_GPIO migration is complete and
GPIO_EXTRA_HEADER is no longer needed.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Upstream Linux uses the "amlogic,meson-axg-usb-ctrl" for AXG SoCs.
This adds it to the compatible list for this driver.
Reported-by: Vyacheslav Bocharov <adeep@lexina.in>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Vyacheslav Bocharov <adeep@lexina.in>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last ARCH_MX25 platform, remove those
references as well.
Cc: Matthias Weisser <weisserm@arcor.de>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last mx35 platform, remove that support as
well.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This converts the following to Kconfig:
CONFIG_OMAP_EHCI_PHY1_RESET_GPIO
CONFIG_OMAP_EHCI_PHY2_RESET_GPIO
CONFIG_OMAP_EHCI_PHY3_RESET_GPIO
To do this, we also introduce CONFIG_HAS_CONFIG_OMAP_EHCI_PHYn_RESET_GPIO
options to get setting the GPIO number.
Signed-off-by: Tom Rini <trini@konsulko.com>
At this point in time, all platforms that had previously used
drivers/usb/phy/omap_usb_phy.c have been migrated to DM and related
options. Remove this now unused code and some related unused defines.
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds support for the DWC_sub31 controllers such as those
found on Apple's M1 SoC. This version of the controller
seems to work fine with the existing driver.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Allow using different PHY interfaces for multiple USB controllers. When no
value is set in DT, we fall back to CONFIG_MXC_USB_PORTSC for now to stay
compatible with current board configurations.
This also adds support for the HSIC mode of the i.MX7.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Import usb_phy_interface enum values and DT match strings from the Linux
kernel.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Some platforms, like the Allwinner H6, do not have a separate glue layer
around the dwc3. Instead, they rely on the clocks/resets/phys referenced
from the dwc3 DT node itself. Add support for enabling the clocks/resets
referenced from the dwc3 DT node.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Resetting an XHCI controller inside xhci_register undoes any register
setup performed by the platform driver. And at least on the Allwinner
H6, resetting the XHCI controller also resets the PHY, which prevents
the controller from working. That means the controller must be taken out
of reset before initializing the PHY, which must be done before calling
xhci_register.
The logic in the XHCI core was added to support the Raspberry Pi 4
(although this was not mentioned in the commit log!), which uses the
xhci-pci platform driver. Move the reset logic to the platform driver,
where it belongs, and where it cannot interfere with other platform
drivers.
This also fixes a failure to call reset_free if xhci_register failed.
Fixes: 0b80371b35 ("usb: xhci: Add reset controller support")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
