Add a new CONFIG_USB_HUB_DEBOUNCE_TIMEOUT to increase the
HUB_DEBOUNCE_TIMEOUT value, for example to 2s because some usb device
needs around 1.5s or more to make the hub port status to be
connected steadily after being powered off and powered on.
This 2s value is aligned with Linux driver and avoids to configure
"usb_pgood_delay" as a workaround for connection timeout on
some USB device; normally the env variable "usb_pgood_delay" is used
to delay the first query after power ON and thus the device answer,
but this variable not used to increase the connection timeout delay.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This enables MMC support, which is available
on Condor board, by default.
Signed-off-by: Andrey Dolnikov <andrey.dolnikov@cogentembedded.com>
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
The eMMC card has two supplies, VCC and VCCQ. The VCC supplies the NAND
array and the VCCQ supplies the bus. On Condor, the VCC is connected to
3.3V rail, while the VCCQ is connected to 1.8V rail. Adjust the pinmux
to match the bus, which is always operating in 1.8V mode.
Based on Linux commit 69efe4bbeda50745 ("arm64: dts: renesas: condor:
Switch eMMC bus to 1V8") from Wolfram Sang
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
This board requires SPI NOR fast-read, otherwise the SPI NOR
access returns corrupted data. Enable the fast-read explicitly
in DT as it has been disabled in the MTD subsystem by commit
d008190920 ("mtd: spi-nor: Mask out fast read if not requested in DT")
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Since R-Car Gen3 already enables position independent build, also set
CONFIG_TEXT_BASE=0x0 to finalize the switch. This is possible since
534f0fbd65 ("arm64: Fix relocation of env_addr if POSITION_INDEPENDENT=y")
fixed current env_get_char() crash with CONFIG_TEXT_BASE=0x0 .
This change permits us to start U-Boot from any location in DRAM instead
of specific TEXT_BASE.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Since R-Car Gen3 already enables position independent build, also set
CONFIG_TEXT_BASE=0x0 to finalize the switch. This is possible since
534f0fbd65 ("arm64: Fix relocation of env_addr if POSITION_INDEPENDENT=y")
fixed current env_get_char() crash with CONFIG_TEXT_BASE=0x0 .
This change permits us to start U-Boot from any location in DRAM instead
of specific TEXT_BASE.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Enable LTO (link time optimization) to improve optimization
and reduce code size by cca. 30 kiB.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Enable LTO (link time optimization) to improve optimization
and reduce code size by cca. 29 kiB.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Enable LTO (link time optimization) to improve optimization
and reduce code size by cca. 34 kiB.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Enable LTO (link time optimization) to improve optimization
and reduce code size by cca. 32 kiB.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Enable LTO (link time optimization) to improve optimization
and reduce code size by cca. 32 kiB.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Enable LTO (link time optimization) to improve optimization
and reduce code size by cca. 31 kiB.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Add calibration support for stm32-adc
Linux kernel v6.1 DT synchronization for stm32mp151.dtsi
stm32mp157a-dk1-scmi-u-boot.dtsi update
Add support of OP-TEE and STM32MP13x in bsec driver
ECDSA various fixes for stm32mp
-----BEGIN PGP SIGNATURE-----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=SNID
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20230113' of https://source.denx.de/u-boot/custodians/u-boot-stm
Add driver to manage onboard hub supplies
Add calibration support for stm32-adc
Linux kernel v6.1 DT synchronization for stm32mp151.dtsi
stm32mp157a-dk1-scmi-u-boot.dtsi update
Add support of OP-TEE and STM32MP13x in bsec driver
ECDSA various fixes for stm32mp
With U-Boot having access to ROM API call table, it is possible to use
the ROM API call it authenticate e.g. signed kernel fitImages using the
BootROM ECDSA support. Make this available by pulling the ECDSA BootROM
call support from SPL-only guard.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
The ROM API table pointer is no longer accessible from U-Boot, fix
this by passing the ROM API pointer through. This makes it possible
for U-Boot to call ROM API functions to authenticate payload like
signed fitImages.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
The STM32MP15xx platform currently comes with two incompatible
implementations of save_boot_params() weak function override.
Factor the save_boot_params() implementation into common cpu.c
code and provide accessors to read out both ROM API table address
and DT address from any place in the code instead.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
In case Dcache is enabled while the ECDSA authentication function is
called via BootROM ROM API, the MMU tables are set up and the BootROM
region is not marked as executable, so an attempt to run code from it
results in a hang. Mark the BootROM region as executable as suggested
by Patrick to prevent the hang.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
In efi_disk_add_dev() we have to open protocols with BY_DRIVER and
BY_CHILD_CONTROLLER. Provide the handle of the EFI block driver. The actual
usage of the value will follow in a later patch.
Change function descriptions to Sphinx style.
Remove a TODO: tag.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add a test for the case when the HII database protocol
set_keyboard_layout() function is called with a NULL key_guid argument.
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
As per the EFI specification, the HII database protocol function
set_keyboard_layout() must return EFI_INVALID_PARAMETER when it is called
with a NULL key_guid argument. Modify the function accordingly to improve
conformance.
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
After calling EFI_ENTRY we have to call EFI_EXIT before returning.
Add a missing EFI_EXIT().
Fixes: 1ccf87165e ("efi_loader: Enable RISCV_EFI_BOOT_PROTOCOL support")
Reported-by: Dave Jones <dave.jones@canonical.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Sunil V L <sunilvl@ventanamicro.com>
_relocate() needs the information in .rela* for self relocation
of the EFI binary.
Fixes: d7ddeb66a6 ("efi_loader: fix building aarch64 EFI binaries")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add infodocs target to CI testing.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Remove non-existent parameter 'n' from function description.
Fixes: 7a9b366cd9 ("lib: add function u16_strcasecmp()")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
- Bring in a number of assorted updates, some of which have been waiting
around for a bit. Make silent console really be silent, get rid of
gpio_hog_probe_all, add RNG for imx6, make net/fm use fs_loader, get
rid of a bad __weak usage and set distro_bootpart_uuid in another case.
The gpio_hog_probe_all() functionality can be perfectly well replaced by
DM_FLAG_PROBE_AFTER_BIND DM flag, which would trigger .probe() callback
of each GPIO hog driver instance after .bind() and thus configure the
hogged GPIO accordingly.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Currently, dm_probe_devices checks that the flags of the device contains
DM_FLAG_PRE_RELOC. However DM_FLAG_PRE_RELOC is a driver - and not a
device - flag. This means that the check in pre_reloc_only mode would
always fail.
Instead, what was aimed to be checked is that either the driver of the
device has the flag set, or that the device has the u-boot,dm-pre-reloc
Device Tree property set.
So let's fix the check to allow u-boot,dm-pre-reloc devices to be
probed.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
The assignment of block device nodes in Linux is not deterministic by
default, i.e. a newly added eMMC controller or other block device can
change the assignment of /dev/mmcblkN (or other block device node like
e.g. /dev/sdXy) and prevent the system from picking the correct block
device for root filesystem in case the root filesystem is specified on
kernel command line using 'root=/dev/mmcblkNpM' (or 'root=/dev/sdXy'
etc.).
One way out is to derive PARTUUID in U-Boot, which is unique identifier
of a partition, and pass that as root=PARTUUID=<partuuid> to Linux via
kernel command line. Linux would then find the partition using PARTUUID,
no matter on which block device the partition resides and which node was
assigned to that block device.
Derive the PARTUUID before scanning for extlinux presence and assign it
into distro_bootpart_uuid environment variable, which can then be used
in extlinux.conf kernel command line specifier.
Note that it is not possible to do this in scan_dev_for_extlinux script
because this script is called from scan_dev_for_boot script, which is
called for both block devices as well as UBI volumes, and we can not
derive PARTUUID for UBI volumes.
Signed-off-by: Marek Vasut <marex@denx.de>
This reverts commit 65ba7add0d.
A weak extern is a nasty sight to behold: If the symbol is never
defined, on ARM, the linker will replace the function call with a NOP.
This behavior isn't well documented but there are at least some hints
to it [1].
When timer_read_counter() is not defined, this obviously does the wrong
thing here and it does so silently. The consequence is that a board
without timer_read_counter() will sleep for random amounts and generally
have erratic get_ticks() values.
Drop the __weak annotation of the extern so a linker error is raised
when timer_read_counter() is not defined. This is okay, the original
reason for the reverted change - breaking the sandbox build - no longer
applies.
Final sidenote: This was the only weak extern in the entire tree at
this time as far as I can tell. I guess we should avoid introduction of
them again as they are obviously a very big footgun.
[1]: https://stackoverflow.com/questions/31203402/gcc-behavior-for-unresolved-weak-functions
Fixes: 65ba7add0d ("time: add weak annotation to timer_read_counter declaration")
Reported-by: Serge Bazanski <q3k@q3k.org>
Signed-off-by: Harald Seiler <hws@denx.de>
This adds a new method to load Fman firmware from a filesystem. This
allows users to use regular files instead of hard-coded offsets for the
firmware.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
In order to read the firmware from the filesystem, we need a file name.
Read the firmware name from the device tree, using the firmware-name
property. This property is commonly used in Linux to determine the
correct name to use (and can be seen in several device trees in U-Boot).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The fs_loader device is used to pull in settings via the chosen node.
However, there was no library function for this, so arria10 was doing it
explicitly. This function subsumes that, and uses ofnode_get_chosen_node
instead of navigating the device tree directly. Because fs_loader pulls
its config from the environment by default, it's fine to create a device
with nothing backing it at all. Doing this allows enabling
CONFIG_FS_LOADER without needing to modify the device tree.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This commit adds configs required for using dcp_rng driver in imx6ull
defconfig files.
Signed-off-by: Kshitiz Varshney <kshitiz.varshney@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
This commit introduces Random number generator to uboot. It uses DCP
driver for number generation.
RNG driver can be invoked by using below command on uboot prompt:-
rng <number of bytes>
Signed-off-by: Kshitiz Varshney <kshitiz.varshney@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Instead of always retuning success, return actual result of
load_simple_fit_image or spl_parse_image_header, otherwise we
might end up jumping on uninitialized spl_image->entry_point.
Signed-off-by: Nikita Shubin <n.shubin@yadro.com>
Reviewed-by: Stefan Roese <sr@denx.de>
When only sspi is entered, help information can be printed.
Signed-off-by: chenzhipeng <chenzhipeng@eswincomputing.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a config-option which forces the console to stay silent until the
proper environment is loaded from flash.
This is important when the default environment does not silence the
console but no output must be printed when 'silent' is set in the flash
environment.
After the environment from flash is loaded, the console will be
silenced/unsilenced depending on it. If PRE_CONSOLE_BUFFER is also
used, the buffer will now be flushed if the console should not be
silenced.
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Activate the command stm32key with CONFIG_CMD_STM32KEY.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Activate the command fuse to access on STM32MP13x OTP with
the BSEC driver.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add support for "st,stm32mp13-bsec" for STM32MP13x in the
bsec driver based on OP-TEE pseudo TA STM32MP BSEC.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
When OP-TEE is used, the SMC for BSEC management are not available and
the STM32MP BSEC pseudo TA must be used (it is mandatory for STM32MP13
and it is a new feature for STM32MP15x).
The BSEC driver try to open a session to this PTA BSEC at probe
and use it for OTP read or write access to fuse or to shadow.
This patch also adapts the commands stm32key and stboard to handle
the BSEC_LOCK_PERM lock value instead of 1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Remove unnecessary return in stm32mp_bsec_write_lock and replace tab
by space for plat_auto opts.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The timer units in the stm32mp15x CPUs have interrupts, depending on the
timer flavour either one "global" or four dedicated ones. Add the irqs
to the timer units on stm32mp15x.
Sync the DT Files with linux kernel v6.1 and with commit a9b70102253ce
("ARM: dts: stm32: Add timer interrupts on stm32mp15")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Remove unnecessary space in device tree stm32mp15xx-dkx.dtsi.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The include file stm32mp1-clksrc.h is not necessary for the SCMI STM32MP15
dtsi files as the clock tree is not defined in the U-Boot SCMI device tree;
these SCMI device tree only support TFABOOT with stm32mp15_defconfig,
SPL with the basic boot defconfig is not supported.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add support of offset and linear calibration for STM32MP15.
The calibration is performed once at probe. The ADC is set in power on
state for calibration. It remains in this state after calibration,
to give to the kernel the opportunity to retrieve calibration data,
directly from the ADC.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
