Commit graph

793 commits

Author SHA1 Message Date
Wolfgang Denk
670c24f6f3 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
* 'master' of git://git.denx.de/u-boot-mpc85xx:
  fsl_lbc: add printout of LCRR and LBCR to local bus regs
  sbc8548: Fix up local bus init to be frequency aware
  sbc8548: enable support for hardware SPD errata workaround
  sbc8548: relocate fixed ddr init code to ddr.c file
  sbc8548: Make enabling SPD RAM configuration work
  sbc8548: Fix LBC SDRAM initialization settings
  sbc8548: enable ability to boot from alternate flash
  sbc8548: relocate 64MB user flash to sane boundary
  Revert "SBC8548: fix address mask to allow 64M flash"
  MPC85xxCDS: Fix missing LCRR_DBYP bits for 66-133MHz LBC
  eXMeritus HWW-1U-1A: Add support for the AT24C128N I2C EEPROM
  eXMeritus HWW-1U-1A: Minor environment variable tweaks
2012-01-13 20:38:49 +01:00
Paul Gortmaker
3e3262bd14 sbc8548: enable support for hardware SPD errata workaround
Existing boards by default have an issue where the LBC SDRAM
SPD EEPROM and the DDR2 SDRAM SPD EEPROM both land at 0x51.

After the hardware modification listed in the README is made,
then the DDR2 SPD EEPROM appears at 0x53.  So this implements
a board specific get_spd() by taking advantage of the existing
weak linkage, that 1st tries reading at 0x53 and then if that
fails, it falls back to the old 0x51.

Since the old dependency issue of "SPD implies no LBC SDRAM"
gets removed with the hardware errata fix, remove that restriction
in the code, so both LBC SDRAM and SPD can be selected.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-01-11 13:59:14 -06:00
Paul Gortmaker
7e44f2b710 sbc8548: Make enabling SPD RAM configuration work
Previously, SPD configuration of RAM was non functional on
this board.  Now that the root cause is known (an i2c address
conflict), there is a simple end-user workaround - remove the
old slower local bus 128MB module and then SPD detection on the
main DDR2 memory module works fine.

We make the enablement of the LBC SDRAM support conditional on
being not SPD enabled.  We can revisit this dependency as the
hardware workaround becomes available.

Turning off LBC SDRAM support revealed a couple implict dependencies
in the tlb/law code that always expected an LBC SDRAM address.

This has been tested with the default 256MB module, a 512MB
a 1GB and a 2GB, of varying speeds, and the SPD autoconfiguration
worked fine in all cases.

The default configuration remains to go with the hard coded
DDR config, so the default build will continue to work on boards
where people don't bother to read the docs.  But the advantage
of going to the SPD config is that even the small default module
gets configured for CL3 instead of CL4.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-01-11 13:59:07 -06:00
Paul Gortmaker
f0aec4ea33 sbc8548: enable ability to boot from alternate flash
This board has an 8MB soldered on flash, and a 64MB SODIMM
flash module.  Normally the board boots from the 8MB flash,
but the hardware can be configured for booting from the 64MB
flash as well by swapping CS0 and CS6.  This can be handy
for recovery purposes, or for supporting u-boot and VxBoot
at the same time.

To support this in u-boot, we need to have different BR0/OR0
and BR6/OR6 settings in place for when the board is configured
in this way, and a different TEXT_BASE needs to be used due
to the larger sector size of the 64MB flash module.

We introduce the suffix _8M and _64M for the BR0/BR6 and the
OR0/OR6 values so it is clear which is being used to map what
specific device.

The larger sector size (512k) of the alternate flash needs
a larger malloc pool, otherwise you'll get failures when
running saveenv, so bump it up accordingly.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-01-11 13:58:14 -06:00
Paul Gortmaker
3fd673cf36 sbc8548: relocate 64MB user flash to sane boundary
The current situation has the 64MB user flash at an awkward
alignment; shifted back from 0xfc00_0000 by 8M, to leave an 8MB hole
for the soldered on boot flash @ EOM.  But to switch to optionally
supporting booting off the 64MB flash, the 64MB will then be mapped
at the sane address of 0xfc00_0000.

This leads to awkward things when programming the 64MB flash prior
to transitioning to it -- i.e. even though the chip spans from
0xfb80_0000 to 0xff7f_ffff, you would have to program a u-boot image
into the two sectors from 0xfbf0_0000 --> 0xfbff_ffff so that it was
in the right place when JP12/SW2.8 were switched to make the 64MB on
/CS0. (i.e. the chip is only looking at the bits in mask 0x3ff_ffff)

We also have to have three TLB entries responsible for dealing with
mapping the 64MB flash due to this 8MB of misalignment.

In the end, there is address space from 0xec00_0000 to 0xefff_ffff
where we can map it, and then the transition from booting from one
config to the other will be a simple 0xec --> 0xfc mapping.  Plus we
can toss out a TLB entry.

Note that TLB0 is kept at 64MB and not shrunk down to the 8MB boot
flash; this means we won't have to change it when the alternate
config uses the full 64MB for booting, in TLB0.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-01-11 13:58:10 -06:00
Thierry Reding
314284b156 mmc: Change board_mmc_getcd() function prototype.
The new API no longer uses the extra cd parameter that was used to store
the card presence state. Instead, this information is returned via the
function's return value. board_mmc_getcd() returns -1 to indicate that
no card-detection mechanism is implemented; 0 indicates that no card is
present and 1 is returned if it was detected that a card is present.

The rationale for this change can be found in the following email
thread:

	http://lists.denx.de/pipermail/u-boot/2011-November/110180.html

In summary, the old API was not consistent with the rest of the MMC API
which always passes a struct mmc as the first parameter. Furthermore the
cd parameter was used to mean "card absence" in some implementations and
"card presence" in others.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Jason Liu <jason.hui@linaro.org>
2012-01-08 21:28:27 -06:00
Wolfgang Denk
145afab32c Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm:
  tegra2: Optimize out-of-tree build for Ventana.
  tegra: Move boards over to use arch-level board UART function
  tegra: Add support for UART init in cpu board.c
  tegra: Add a function mux feature
  tegra: add clock_ll_start_uart() to enable UART prior to reloc
  tegra: Move clock_early_init() to arch_cpu_init()
  tegra: Move cpu_init_cp15() to arch_cpu_init()
  arm: Tegra: Fix Harmony and Ventana builds in u-boot-tegra/master
  tegra: Fix build error in plutux, medcom
  tegra2: Add Avionic Design Medcom support.
  tegra2: Add Avionic Design Plutux support.
  tegra2: Add common Avionic Design Tamonten support.
  tegra2: Move tegra2_mmc_init() prototype to public header.
  tegra2: Change CONFIG_SYS_TEXT_BASE to 0x00108000.
  tegra2: Always build with USE_PRIVATE_LIBGCC=yes.
  tegra2: Plumb in SPI/UART switch code
  tegra2: spi: Support SPI / UART switch
  tegra2: Implement SPI / UART GPIO switch
  tegra2: Enable SPI environment on Seaboard
  tegra2: config: Enable SPI flash on Seaboard
  tegra2: spi: Add SPI driver for Tegra2 SOC
  tegra2: Add UARTB support
  tegra2: Tidy UART selection
  arm, davinci: Fix build warnings for cam_enc_4xx
  Devkit8000: Switch over to enable_gpmc_cs_config
  arm, davinci: Add support for generating AIS images to the Makefile
  mkimage: Fix variable length header support
  arm, da850evm: Add an SPL for SPI boot
  arm, davinci: Add SPL support for DA850 SoCs
  sf: Add spi_boot() to allow booting from SPI flash in an SPL
  spl: display_options.o is required for SPI flash support in SPL
  ARM: omap3: add support to Technexion twister board
  ARM: omap3: added common configuration for Technexion TAM3517
  vision2: Fix checkpatch warning
2012-01-05 16:38:50 +01:00
Tom Rini
2620368a61 git-mailrc: Add self to davinci/omap, add ti
Adding a 'ti' alias since not all parts are "omap" or "davinci" and
adding myself to that alias as co-custodian of u-boot-ti

Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-01-05 15:59:47 +01:00
Christian Riesch
3d2c8e6c7f arm, da850evm: Add an SPL for SPI boot
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Heiko Schocher <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Tom Rini <trini@ti.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
2011-12-24 10:23:30 +01:00
Christian Riesch
32b1127397 sf: Add spi_boot() to allow booting from SPI flash in an SPL
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Heiko Schocher <hs@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Scott Wood <scottwood@freescale.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2011-12-24 10:23:30 +01:00
Horst Kronstorfer
49fbf4371e doc/mkimage.1: Fix -D/-f options formatting
Signed-off-by: Horst Kronstorfer <hkronsto@frequentis.com>
2011-12-23 20:11:46 +01:00
Horst Kronstorfer
7aecfdd0f8 doc/mkimage.1: Fix some typos
Signed-off-by: Horst Kronstorfer <hkronsto@frequentis.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2011-12-21 20:27:18 +01:00
Wolfgang Denk
6b62b9a31d Coding Style cleanup
Fix trailing white space, indentation by spaces instead of TABs,
excessive blank lines, trailing blank lines.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-12-19 12:03:40 +01:00
Wolfgang Denk
3f3110d78b MIPS: remove broken "tb0229" board
The "tb0229" board has long been unmaintained, and is broken.
Remove it.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-12-12 14:26:48 +01:00
Marek Vasut
ea098e0fb8 M28: Document that units has to be set to sectors on SD bootcard
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
2011-12-09 17:30:10 +01:00
Wolfgang Denk
fb82fd7a32 MPC850: remove obsolete "rmu" Board
The "rmu" board has long been unmaintained, and is broken.
Remove it.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-12-08 20:51:39 +01:00
Wolfgang Denk
309a292e41 MPC8240: remove obsolete "OXC" board
The OXC board has long been unmaintained, and is broken.
Remove it.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-12-08 20:51:33 +01:00
Wolfgang Denk
c53043b7f1 MPC7xx: remove obsolete "BAB7xx" board
The BAB7xx boards are almost deceased.  They cause build warnings, an
it's not worth the effort to fix these.  Remove the dead body.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Frank Gottschling <fgottschling@eltec.de>
2011-12-08 20:51:28 +01:00
Marek Vasut
c477d72c04 PXA: Drop XM250 board
The board is unmaintained and maintainer doesn't respond.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Anatolij Gustschin <agust@denx.de>
2011-12-06 23:59:31 +01:00
Marek Vasut
d299173139 PXA: Drop PLEB2 board
The board is unmaintained and maintainer doesn't respond.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Anatolij Gustschin <agust@denx.de>
2011-12-06 23:59:31 +01:00
Marek Vasut
00c4acaa97 PXA: Drop CRADLE board
The board is unmaintained and maintainer doesn't respond.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Anatolij Gustschin <agust@denx.de>
2011-12-06 23:59:31 +01:00
Marek Vasut
f13eba66fd PXA: Drop CERF250 board
The board is unmaintained and maintainer doesn't respond.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Anatolij Gustschin <agust@denx.de>
2011-12-06 23:59:31 +01:00
Mike Frysinger
8b0b0c59b5 add a git mailrc file for maintainers
This should make sending out e-mails to the right people easier.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-12-06 21:32:19 +01:00
Andy Fleming
1cdabc4bc7 miiphy: Note that miiphy_* API is deprecated
We want to move everything to phylib, and we definitely don't want
new drivers using the miiphy infrastructure.

Signed-off-by: Andy Fleming <afleming@freescale.com>
2011-12-05 22:17:06 +01:00
Nobuhiro Iwamatsu
c67ce95433 sh: Add updating method of SPI ROM to README of sh7757lcr
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2011-12-02 13:46:21 +09:00
Shengzhou Liu
ae6b03fefc powerpc/p3060qds: Add board related support for P3060QDS platform
The P3060QDS is a Freescale reference board for the six-core P3060 SOC.

P3060QDS Board Overview:
 Memory subsystem:
  - 2G Bytes unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
  - 128M Bytes NOR flash single-chip memory
  - 16M Bytes SPI flash
  - 8K Bytes AT24C64 I2C EEPROM for RCW
 Ethernet:
  - Eight Ethernet controllers (4x1G + 4x1G/2.5G)
  - Three VSC8641 PHYs on board (2xRGMII + 1xMII)
  - Suport multiple Vitesse VSC8234 SGMII Cards in Slot1/2/3
 PCIe: Two PCI Express 2.0 controllers/ports
 USB:  Two USB2.0, USB1(TYPE-A) and USB2(TYPE-AB) on board
 I2C:  Four I2C controllers
 UART: Supports two dUARTs up to 115200 bps for console
 RapidIO:  Two RapidIO, sRIO1 and sRIO2

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-29 08:48:06 -06:00
Stelian Pop
762e63754b Fix Stelian's email address
Change my old email address which is no longer valid.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-11-27 19:44:21 +01:00
Marek Vasut
b68d57c310 M28: Add doc/README.m28 documentation
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
2011-11-11 11:36:58 +01:00
Wolfgang Denk
5721385b18 Merge branch 'master' of git://git.denx.de/u-boot-mpc83xx
* 'master' of git://git.denx.de/u-boot-mpc83xx:
  powerpc/mpc83xx: Add 33.33MHz support for mpc8360emds
  powerpc/mpc83xx: Add 512MB DDR support for mpc8360emds
  mpc83xx: Rename CONFIG_SYS_DDR_CONFIG and cleanup DDR csbnds code
  mpc83xx: Cleanup usage of LBC constants
  mpc83xx: Cleanup usage of DDR constants
  mpc83xx: Cleanup usage of BAT constants
  mpc83xx: cosmetic: vme8349.h checkpatch compliance
  mpc83xx: cosmetic: ve8313.h checkpatch compliance
  mpc83xx: cosmetic: sbc8349.h checkpatch compliance
  mpc83xx: cosmetic: mpc8308_p1m.h checkpatch compliance
  mpc83xx: cosmetic: kmeter1.h checkpatch compliance
  mpc83xx: cosmetic: TQM834x.h checkpatch compliance
  mpc83xx: cosmetic: SIMPC8313.h checkpatch compliance
  mpc83xx: cosmetic: MVBLM7.h checkpatch compliance
  mpc83xx: cosmetic: MPC837XERDB.h checkpatch compliance
  mpc83xx: cosmetic: MPC837XEMDS.h checkpatch compliance
  mpc83xx: cosmetic: MPC8360ERDK.h checkpatch compliance
  mpc83xx: cosmetic: MPC8360EMDS.h checkpatch compliance
  mpc83xx: cosmetic: MPC8349ITX.h checkpatch compliance
  mpc83xx: cosmetic: MPC8349EMDS.h checkpatch compliance
  mpc83xx: cosmetic: MPC832XEMDS.h checkpatch compliance
  mpc83xx: cosmetic: MPC8323ERDB.h checkpatch compliance
  mpc83xx: cosmetic: MPC8315ERDB.h checkpatch compliance
  mpc83xx: cosmetic: MPC8313ERDB.h checkpatch compliance
  mpc83xx: cosmetic: MPC8308RDB.h checkpatch compliance
  mpc83xx: cosmetic: MERGERBOX.h checkpatch compliance
  mpc83xx: Fix ipic structure definition
  powerpc, mpc83xx: add DDR SDRAM Timing Configuration 3 definitions
  cosmetic, powerpc, mpc83xx: checkpatch cleanup
  powerpc/83xx: move km 83xx specific i2c code to km83xx_i2c
  mpc83xx: fix global timer structure definition
2011-11-08 07:44:52 +01:00
Jerry Huang
6be55ee225 powerpc/mpc83xx: Add 33.33MHz support for mpc8360emds
The new MPC8360EMDS board changes the oscillator to 33.33MHz
in order to support QE 500MHz since 2008.

Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-07 18:34:40 -06:00
Michael Jones
84d7a0171f OMAP3: mvblx: Initial support for mvBlueLYNX-X
Add support for the MATRIX VISION mvBlueLYNX-X, an OMAP3-based
intelligent camera.

Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-04 13:54:33 -04:00
Heiko Schocher
4dd834906d arm, davinci: add cam_enc_4xx support
- DM368 SOC
- booting with spl not with UBL from TI
- before loading u-boot from NAND into RAM, test
  the RAM with the post memory test. If error
  is found, switch all LEDs on and halt system.
- SPI Flash
  Dataflash Typ: M25PE80
- Ethernet DM9161BI
- MMC
- USB

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-03 22:56:25 +01:00
Heiko Schocher
435199f380 arm, davinci: add support for new spl framework
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-03 22:56:25 +01:00
Heiko Schocher
18e8ff18fa spl: add option for adding post memory test to the SPL framework
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-03 22:56:24 +01:00
Simon Schwarz
3a0d60c504 SPL: Add DMA library
Adding a DMA library to the SPL. It is used if CONFIG_SPL_DMA_SUPPORT is
defined.

Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-10-27 21:56:34 +02:00
Simon Schwarz
4c4bb19d05 omap3: Add interface for omap3 DMA
Adds an interface to use the OMAP3 DMA.

Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-10-27 21:56:34 +02:00
Simon Glass
eea63e05d0 fdt: ARM: Add fdtcontroladdr to set device tree address in environment
This adds support for a new environment variable called 'fdtcontroladdr'. If
defined, the hex address is used as the address of the control fdt for U-Boot.

Note: I have not changed CONFIG_PRAM section as I already have an
outstanding patch on that.

Signed-off-by: Simon Glass <sjg@chromium.org>
2011-10-26 21:40:16 +02:00
Simon Glass
bbb0b128c3 fdt: Add support for embedded device tree (CONFIG_OF_EMBED)
This new option allows U-Boot to embed a binary device tree into its image
to allow run-time control of peripherals. This device tree is for U-Boot's
own use and is not necessarily the same one as is passed to the kernel.

The device tree compiler output should be placed in the $(obj)
rooted tree. Since $(OBJCOPY) insists on adding the path to the
generated symbol names, to ensure consistency it should be
invoked from the directory where the .dtb file is located and
given the input file name without the path.

This commit contains my entry for the ugliest Makefile / shell interaction
competition.

Signed-off-by: Simon Glass <sjg@chromium.org>
2011-10-26 21:38:59 +02:00
Anton staaf
46a6d51c82 cache: add ALLOC_CACHE_ALIGN_BUFFER macro
This macro is used to allocate cache line size aligned stack
buffers for use with DMA hardware.

Signed-off-by: Anton Staaf <robotboy@chromium.org>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Aneesh V <aneesh@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Wolfgang Denk <wd@denx.de>
2011-10-25 09:23:10 +02:00
Wolfgang Denk
e877fabeb9 MPC85xx: remove broken "mpq101" board
The board stopped building some time ago, and the board maintainer
agrtees to drop it - see
http://article.gmane.org/gmane.comp.boot-loaders.u-boot/112674

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
2011-10-23 17:00:47 +02:00
Joe Hershberger
b3f44c21ea common: cosmetic: CONFIG_BOOTFILE checkpatch compliance
Remove MK_STR from places that consume CONFIG_BOOTFILE to force all definitions to be string literals.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2011-10-22 01:21:35 +02:00
Macpaul Lin
afc1ce8288 doc/README: documents and readme for NDS32 arch
Documents and READMEs for NDS32 architecture.
It patch also provides usage of SoC AG101 and board ADP-AG101.

Signed-off-by: Macpaul Lin <macpaul@andestech.com>
2011-10-22 00:54:45 +02:00
Simon Glass
744d9859a7 sandbox: Add architecture header files
This adds required header files for the sandbox architecture, and a basic
description of what sandbox is (README.sandbox).

Signed-off-by: Simon Glass <sjg@chromium.org>
2011-10-17 22:45:50 +02:00
Jason Hobbs
06283a6401 Add pxe command
Add pxe command, which is intended to mimic PXELINUX functionality.
'pxe get' uses tftp to retrieve a file based on UUID, MAC address or IP
address. 'pxe boot' interprets the contents of PXELINUX config like file
to boot using a specific initrd, kernel and kernel command line.

This patch also adds a README.pxe file - see it for more details on the
pxe command.

Signed-off-by: Jason Hobbs <jason.hobbs@calxeda.com>
2011-10-17 22:25:35 +02:00
Jason Hobbs
b41bc5a82d common, menu: use abortboot for menu timeout
Signed-off-by: Jason Hobbs <jason.hobbs@calxeda.com>
2011-10-17 22:25:33 +02:00
Jason Hobbs
b69bf52dfe Add generic, reusable menu code
This will be used first by the pxe code, but is intended to be
generic and reusable for other jobs in U-boot.

Signed-off-by: Jason Hobbs <jason.hobbs@calxeda.com>
2011-10-17 22:25:33 +02:00
York Sun
6f5e1dc531 powerpc/8xxx: Add support for interactive DDR programming interface
Interactive DDR debugging provides a user interface to view and modify SPD,
DIMM parameters, board options and DDR controller registers before DDR is
initialized. With this feature, developers can fine-tune DDR for board
bringup and other debugging without frequently having to reprogram the flash.

To enable this feature, define CONFIG_FSL_DDR_INTERACTIVE in board header
file and set an environment variable to activate it. Syntax:

setenv ddr_interactive on

After reset, U-boot prompts before initializing DDR controllers
FSL DDR>

The available commands are
print      print SPD and intermediate computed data
reset      reboot machine
recompute  reload SPD and options to default and recompute regs
edit       modify spd, parameter, or option
compute    recompute registers from current next_step to end
next_step  shows current next_step
help       this message
go         program the memory controller and continue with u-boot

The first command should be "compute", which reads data from DIMM SPDs and
board options, performs the calculation then stops before setting DDR
controller. A user can use "print" and "edit" commands to view and modify
anything. "Go" picks up from current step with any modification and
compltes the calculation then enables the DDR controller to continue u-boot.
"Recompute" does it over from fresh reading.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-09 17:57:53 -05:00
Mike Frysinger
e2a53458a7 net: drop !NET_MULTI code
This is long over due.  All but two net drivers have been converted, but
those have now been dropped.

The only thing left to do is actually delete all references to NET_MULTI
and code that is compiled when that is not defined.  So here we scrub the
core code.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-10-05 22:22:16 +02:00
Mike Frysinger
1285a2808a mkconfig: start deprecating Makefile config targets
Now that we've got boards.cfg and most people have converted over,
start warning people who have yet to so we can phase board configs
completely out of the Makefile.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-10-05 22:22:15 +02:00
Wolfgang Denk
4f7549d2dc Merge branch 'master' of git://git.denx.de/u-boot-nand-flash
* 'master' of git://git.denx.de/u-boot-nand-flash:
  PPC: Fix socrates NAND problem
  PPC: Fix fsl_upm.c by renaming nand handling functions
  NAND: Make page, erase, oob size available via cmd_nand
  mtd: eLBC NAND: remove elbc_fcm_ctrl->oob_poi
  NAND: Add -y option to nand scrub command
  NAND: Add nand read.raw and write.raw commands
  NAND: Really ignore bad blocks when scrubbing
  spl, nand: add 4bit HW ecc oob first nand_read_page function
  mxc_nand: fix a problem writing more than 32MB
  mxc_nand: fixed some typos (cosmetic)
  nand: increase chip_delay in mv kirkwood nand driver
2011-10-04 22:20:25 +02:00
Wolfgang Denk
1fed668b3f Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
* 'master' of git://git.denx.de/u-boot-mpc85xx:
  powerpc/p3060: Add SoC related support for P3060 platform
  powerpc/85xx: Add support for setting up RAID engine liodns on P5020
  powerpc/85xx: Refactor some defines out of corenet_ds.h
  fm-eth: Add ability for board code to disable a port
  powerpc/mpc8548: Add workaround for erratum NMG_LBC103
  powerpc/mpc8548: Add workaround for erratum NMG_DDR120
  powerpc/mpc85xxcds: Fix PCI speed
  powerpc/mpc8548cds: Fix booting message
  powerpc/p4080: Add support for secure boot flow
  powerpc/85xx: Add Secure Boot support on P1010RDB for NOR, NAND & SPIFLASH
  powerpc/85xx: Add PBL & SECUREBOOT support on P3041/P5020DS boards
  powerpc/p2041rdb: remove watch dog related codes
  powerpc/p2041rdb: updated description of cpld command
  powerpc/p2041rdb: add more ddr frequencies support
  powerpc/p2041rdb: set sysclk according to status of physical switch SW1
  powerpc/p2041rdb: update cpld reset command according to CPLD 2.0
  powerpc/mpc8349emds: Migrate from spd_sdram to unified DDR driver
  powerpc/mpc83xx: Migrate from spd_sdram to unified DDR driver
  powerpc/mpc8xxx: Add DDR2 to unified DDR driver
  powerpc/mpc8xxx: Fix picos_to_mclk() and get_memory_clk_period_ps()
  powerpc/mpc8xxx: Add SPD EEPROM address for single controller 2 slots
  powerpc/mpc8xxx: Fix DDR code for empty first DIMM slot and enable DQS_en
  powerpc/85xx: Refactor P2041RDB to use common p_corenet files
  powerpc/85xx: refactor common P-Series CoreNet files for FSL boards
  powerpc/85xx: Enable CMD_REGINFO on corenet boards
  powerpc/85xx: p2041rdb - Remove unused 'execute' perm in TLB entries
  powerpc/85xx: Fix USB protocol definitions for P1020RDB
  powerpc/corenet_ds: Use separated speed tables for UDIMM and RDIMM
  powerpc/mpc8xxx: Move DDR RCW overriding to common code
  powerpc/mpc8xxx: Extend CWL table
  powerpc/85xx: Cleanup how SVR_MAJ() is defined on MPC8536
  powerpc/85xx: Cleanup extern in corenet_ds board code
  powerpc/p2041rdb: Add ethernet support on P2041RDB board
  powerpc/85xx: Add networking support to P1023RDS
  powerpc/hydra: Add ethernet support on P5020/P3041 DS boards
  powerpc/85xx: Add FMan ethernet support to P4080DS
  powerpc/85xx: Add support for FMan ethernet in Independent mode
  powerpc/mpc8548cds: Cleanup mpc8548cds.c
  powerpc/mp: add support for discontiguous cores
  powerpc/85xx: corenet_ds - Remove unused 'execute' perm in TLB entries
  fdt: Add new fdt_create_phandle helper
  fdt: Rename fdt_create_phandle to fdt_set_phandle
  powerpc/85xx: Fix compile warnings/errors if CONFIG_SYS_DPAA_FMAN isn't set
  fsl_ifc: Add the workaround for erratum IFC A-003399(enabled on P1010)
  powerpc/P1010: Add workaround for erratum P1010-A003549 (related to IFC)
  fsl_ifc: Add the workaround for erratum IFC-A002769 (enable on P1010)
  powerpc/85xx: Expanding the window of CCSRBAR in AS=1 from 4k to 1M
  powerpc/85xx: Add NAND/NAND_SPL support to P1010RDB
  nand: Freescale Integrated Flash Controller NAND support
  powerpc/85xx: Add basic support for P1010RDB
  powerpc/85xx: Add support for new P102x/P2020 RDB style boards
  powerpc/85xx: relocate CCSR before creating the initial RAM area
  powerpc/85xx: introduce and document CONFIG_SYS_CCSRBAR macros
  powerpc/85xx: Enable internal USB UTMI PHY on p204x/p3041/p50x0
  powerpc/85xx: Add ULPI and UTMI USB Phy support for P1010/P1014
2011-10-04 22:08:13 +02:00
Marek Vasut
fb3659ac42 NAND: Add nand read.raw and write.raw commands
These commands should work around various "hardware" ECC and BCH methods.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
[scottwood@freescale.com: s/write the page/access the page/]
Signed-off-by: Scott Wood <scottwood@freescale.com>
2011-10-03 18:35:12 -05:00
Heiko Schocher
337c433383 arm, davinci: add NOR Boot Configuration Word
to add the "NOR Boot Configuration Word" on AM18xx based boards,
define CONFIG_SYS_DV_NOR_BOOT_CFG.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Paulraj Sandeep <s-paulraj@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-30 22:00:59 +02:00
Simon Schwarz
682b3a81ee spl: Add POWER library to new spl
Adds power library to the new spl

Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-30 22:00:54 +02:00
Simon Schwarz
12c2f1ee3c spl: add NAND Library to new SPL
Adds NAND library to SPL.

Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-30 22:00:54 +02:00
York Sun
4e57382faa powerpc/mpc8xxx: Add DDR2 to unified DDR driver
DDR2 has different ODT table and values. Adding table according to Samsung
application note.

Fix additive latency calculation to avoid interger underflow.

Also converted typedef dynamic_odt_t to struct dynamic_odt.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:06 -05:00
Li Yang
14aa71e660 powerpc/85xx: Add support for new P102x/P2020 RDB style boards
The following boards share a common design but with minor variations
between them:

P1020MSBG-PC
P1020RDB-PC
P1020UTM-PC
P1021RDB-PC
P1024RDB
P1025RDB
P2020RDB-PC

The P1020RDB-PC shares its roots in the existing P1020RDB board design,
however uses DDR3 instead of DDR2.
P2020RDB-PC differs from the P102x RDB-PC with 64-bit DDR and 100Mhz SYSCLK.

Key features on these boards include:
* DDR3
* NOR flash
* NAND flash (on RDB's only)
* SPI flash (on RDB's only)
* SDHC/MMC card slot
* VSC7385 Ethernet switch (on P1020MBG, P1020RDB, & P1021RDB)
* PCIE slot and mini-PCIE slots

As these boards use soldered DDR chips not regular DIMMs, an on-board EEPROM
is used to store SPD data. In case of absent or corrupted SPD, falling back
to timing data embedded in the source code will be used. Raw timing data is
extracted from DDR chip datasheet. Different speeds of DDR are supported
with this approach. ODT option is forced to fit this set of boards, again
because they don't have regular DIMMs.

CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS is defined as 5ms to meet
specification for writing timing.

VSC firmware Address is defined by default in config file for eTSEC1.

SD width is based off DIP switch. DIP switch is detected on the
board by reading i2c bus and setting the appropriate mux values.

Some boards have QE module in the silicon (P1021 and P1025). QE and eLBC
have pins multiplexing. QE function needs to be disabled to access Nor Flash
and CPLD. QE-UEC and QE-UART can be enabled for linux kernel by setting "qe"
in hwconfig. In addition, QE-UEC and QE-TDM also have pins multiplexing, to
enable QE-TDM for linux kernel, set "qe;tdm" in hwconfig. Syntax is as below

'setenv hwconfig qe' to enable QE UEC/UART and disable Nor-Flash/CPLD.
'setenv hwconfig 'qe;tdm'' to enalbe QE TDM and disable Nor-Flash/CPLD.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Zhao Chenhui <b26998@freescale.com>
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Tang Yuantian <b29983@freescale.com>
Signed-off-by: ramneek.mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Akhil Goyal <akhil.goyal@freescale.com>
2011-09-29 19:01:04 -05:00
Wolfgang Denk
ff4dea0383 doc/README.scrapyard: Update board removal commit IDs
Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-09-28 20:42:00 +02:00
Albert ARIBAUD
0ca8eb7137 ARM: remove broken "ixdp425" and "ixpdg425" boards
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Stefan Roese <sr@denx.de>
2011-09-27 08:58:04 +02:00
Vladimir Zapolskiy
7de17781a4 doc: provide a correct board_init_r definition path
This is a trivial fix in the documentation, which corrects
board_init_r() source reference.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2011-09-23 08:12:28 +02:00
Sanjeev Premi
3b690ebbbf omap: gpio: generic changes after changing API
This patch contains the generic changes required after
change to generic API in the previous patch.

Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-13 08:25:15 +02:00
Wolfgang Denk
04e5ae7931 Minor coding style cleanup.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-09-11 21:24:09 +02:00
Wolfgang Denk
b66521a6c1 ARM: PXA: remove broken "zylonite" board.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
2011-09-07 22:00:37 +02:00
Wolfgang Denk
5df092d781 ARM: remove broken "shannon" board.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Rolf Offermanns <rof@sysgo.de>
2011-09-07 21:46:40 +02:00
Wolfgang Denk
9c62815bf7 ARM: remove broken "modnet50" board.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Thomas Elste <info@elste.org>
2011-09-07 21:46:40 +02:00
Wolfgang Denk
d1a067a34a ARM: remove broken "lpc2292sodimm" board.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2011-09-07 21:46:40 +02:00
Wolfgang Denk
3d57573986 ARM: remove broken "lart" board.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Alex Züpke <azu@sysgo.de>
2011-09-07 21:46:40 +02:00
Wolfgang Denk
c1f8750f9f ARM: remove broken "impa7" board.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Marius Gröger <mag@sysgo.de>
2011-09-07 21:46:40 +02:00
Wolfgang Denk
2c650e2010 ARM: remove broken "gcplus" board.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: George G. Davis <gdavis@mvista.com>
2011-09-07 21:46:40 +02:00
Wolfgang Denk
26e670ea43 ARM: remove broken "evb4510" board.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Curt Brune <curt@cucy.com>
2011-09-07 21:46:39 +02:00
Wolfgang Denk
c8f63b415f ARM: remove broken "ep7312" board.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Marius Gröger <mag@sysgo.de>
2011-09-07 21:46:39 +02:00
Wolfgang Denk
fc5e5ceec4 ARM: remove broken "dnp1110" board.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Alex Züpke <azu@sysgo.de>
2011-09-07 21:46:39 +02:00
Wolfgang Denk
6aac646f58 ARM: remove broken "SMN42" board.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2011-09-07 21:45:34 +02:00
Wolfgang Denk
8b075814fd doc/README.scrapyard: Update commit IDs or board removals
Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-09-07 21:44:25 +02:00
Aneesh V
cba4b1809f arm: do not force d-cache enable on all boards
c2dd0d4554 added dcache_enable()
to board_init_r(). This enables d-cache for all ARM boards.
As a result some of the arm boards that are not cache-ready
are broken. Revert this change and allow platform code to
take the decision on d-cache enabling.

Also add some documentation for cache usage in ARM.

Signed-off-by: Aneesh V <aneesh@ti.com>
2011-09-04 11:36:16 +02:00
Wolfgang Denk
1c85752258 ARM: remove broken "at91rm9200dk" board
Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-09-04 11:36:15 +02:00
Wolfgang Denk
b1a2bd4bb3 ARM: remove broken "m501sk" board
Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-09-04 11:36:15 +02:00
Wolfgang Denk
5bd3814bb7 ARM: remove broken "kb9202" board
Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-09-04 11:36:14 +02:00
Wolfgang Denk
d14af08466 ARM: remove broken "csb637" board
Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-09-04 11:36:14 +02:00
Wolfgang Denk
37a9b4d0b7 ARM: remove broken "cmc_pu2" board
Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-09-04 11:36:14 +02:00
Wolfgang Denk
b550834458 ARM: remove broken "at91cap9adk" board
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stelian Pop <stelian.pop@leadtechdesign.com>
2011-09-04 11:36:14 +02:00
Wolfgang Denk
1b793a472e ARM: remove broken "voiceblue" board
Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-09-04 11:36:14 +02:00
Wolfgang Denk
ad218a868b ARM: remove broken "smdk2400" board
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Gary Jennejohn <garyj@denx.de>
2011-09-04 11:36:14 +02:00
Wolfgang Denk
1f7f0edd3c ARM: remove broken "sbc2410x" board
Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-09-04 11:36:14 +02:00
Wolfgang Denk
6ea2405489 ARM: remove broken "netstar" board
Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-09-04 11:36:14 +02:00
Wolfgang Denk
69624195a3 ARM: remove broken "mx1fs2" board
Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-09-04 11:36:13 +02:00
Wolfgang Denk
957731eda0 ARM: remove broken "lpd7a40x" boards
Remove lpd7a400 and lpd7a404 boards.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-09-04 11:36:13 +02:00
Wolfgang Denk
716f7ade10 ARM: remove broken "edb93xx" boards
Remove edb9301, edb9302, edb9302a, edb9307, edb9307a, edb9312,
edb9315 and edb9315a boards.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-09-04 11:36:13 +02:00
Wolfgang Denk
5dcf53696f ARM: remove broken "B2" board
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Andrea Scian <andrea.scian@dave-tech.it>
2011-09-04 11:36:13 +02:00
Wolfgang Denk
be28857072 ARM: remove broken "armadillo" board
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Rowel Atienza <rowel@diwalabs.com>
2011-09-04 11:36:13 +02:00
Wolfgang Denk
c91e90db8c ARM: remove broken "assabet" board
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: George G. Davis <gdavis@mvista.com>
2011-09-04 11:36:13 +02:00
David Jander
9db1bfa110 ARM: MX51: PLL errata workaround
This is a port of the official PLL errata workaround from Freescale to
mainline u-boot.
The PLL's in the i.MX51 processor can go out of lock due to a metastable
condition in an analog flip-flop when used at high frequencies.
This workaround implements an undocumented feature in the PLL (dither
mode), which causes the effect of this failure to be much lower (in terms
of frequency deviation), avoiding system failure, or at least decreasing
the likelihood of system failure.

Signed-off-by: David Jander <david@protonic.nl>
2011-09-04 11:36:11 +02:00
Simon Glass
4fdbcf8113 Add documentation for USB Host Networking
This describes what it is for, devices supported, how to enable for your
board in U-Boot, setting up the server, and notes about MAC addresses.

Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Eric Bénard <eric@eukrea.com>
2011-08-08 21:05:23 +02:00
Albert ARIBAUD
fa82f871c8 Convert ISO-8859 files to UTF-8
There was a mix of UTF-8 and ISO-8859 files in the U-Boot source
tree, which could cause issues with the patchwork review system.
This commit converts all ISO-8859 files to UTF-8.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2011-08-04 23:34:02 +02:00
Andreas Bießmann
15d93d7c06 README.at91-soc: remove AT91(RM9200) joining notice
Since all currently supported at91rm9200 boards are migrated to at91
support the joining notice can be removed.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2011-08-03 13:00:55 +02:00
Mike Williams
1626308797 cleanup: Fix typos and misspellings in various files.
Recieve/Receive
recieve/receive
Interupt/Interrupt
interupt/interrupt
Addres/Address
addres/address

Signed-off-by: Mike Williams <mike@mikebwilliams.com>
2011-07-28 21:27:36 +02:00
Heiko Schocher
7816f2cf81 mkimage: add UBL header support for booting davinci cpus
creating an u-boot.ubl file, which contains the UBL Header
needed for booting from NAND with the RBL from TI. For more
information read doc/README.ublimage.

Signed-off-by: Heiko Schocher <hs@denx.de>
2011-07-28 16:52:41 +02:00
Andreas Pretzsch
7130a579fd add command fitupd to run an update from a FIT image
Command calls update_tftp() analogous to automatic update described
in doc/README.update.

Usage:
fitupd [addr]
        - run update from FIT image at addr
          or from tftp 'updatefile'

Signed-off-by: Andreas Pretzsch <apr@cn-eng.de>
2011-07-26 16:58:48 +02:00
Daniel Schwierzeck
6a11cf48a5 spl: add initial support for a generic SPL framework
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2011-07-26 14:42:12 +02:00
Mingkai Hu
4f1d1b7d1e powerpc/p2041rdb: Add p2041rdb board support
P2041RDB Specification:
-----------------------
Memory subsystem:
 * 4Gbyte unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
 * 128 Mbyte NOR flash single-chip memory
 * 256 Kbit M24256 I2C EEPROM
 * 16 Mbyte SPI memory
 * SD connector to interface with the SD memory card

Ethernet:
 * dTSEC1: connected to the Vitesse SGMII PHY (VSC8221)
 * dTSEC2: connected to the Vitesse SGMII PHY (VSC8221)
 * dTSEC3: connected to the Vitesse SGMII PHY (VSC8221)
 * dTSEC4: connected to the Vitesse RGMII PHY (VSC8641)
 * dTSEC5: connected to the Vitesse RGMII PHY (VSC8641)

PCIe:
 * Lanes E, F, G and H of Bank1 are connected to one x4 PCIe SLOT1
 * Lanes C and Land D of Bank2 are connected to one x4 PCIe SLOT2

SATA: Lanes C and Land D of Bank2 are connected to two SATA connectors

USB 2.0: connected via a internal UTMI PHY to two TYPE-A interfaces

I2C:
 * I2C1: Real time clock, Temperature sensor, Memory module
 * I2C2: Vcore Regulator, 256Kbit I2C Bus EEPROM, PCIe slot1/2

UART: supports two UARTs up to 115200 bps for console

Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-17 11:03:36 -05:00
Ramneek Mehresh
636c316f9b powerpc/85xx: Specify hwconfig usage for USB controller
Specify hwconfig usage for USB mode and phy change

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-11 13:24:20 -05:00
Roy Zang
3f7f6b8592 powerpc/85xx: Add basic support for P1023RDS board
The P1023RDS board is the reference board for the P1023 SoC.

Add support for booting it from NOR or NAND, with fixed 2G of DDR, PCIe,
UART, I2C, etc.

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-11 13:24:20 -05:00
Andre Schwarz
7fb3e7a2d6 mpc83xx: Add support for MergerBox board
Includes board config file, documentation, maintainer and boards.cfg
entries, and board specific files in vendor dir.

Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-07-06 19:09:27 -05:00
Ben Gardiner
c9494866df cmd_nand: add nand write.trimffs command
Add another nand write. variant, trimffs. This command will request of
nand_write_skip_bad() that all trailing all-0xff pages will be
dropped from eraseblocks when they are written to flash as-per the
reccommended behaviour of the UBI FAQ [1].

The function that implements this timming is the drop_ffs() function
by Artem Bityutskiy, ported from the mtd-utils tree.

[1] http://www.linux-mtd.infradead.org/doc/ubi.html#L_flasher_algo

Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Artem Bityutskiy <dedekind1@gmail.com>
CC: Detlev Zundel <dzu@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2011-07-01 15:56:51 -05:00
Wolfgang Denk
566e5cf451 ARM: drop unsupported 'trab' board
The 'trab' board configuration is broken, and there is nobody who is
interested and willing to fix it.  Drop it.

This includes support for VFD displays which have always been used by
this board only.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-06-22 20:00:51 +02:00
Marek Vasut
9f084b1e04 Move wepep250,delta,xsengine to scrapyard
Drop wepep250 board from MAINTAINERS and add all these three boards to
doc/README.scrapyard

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2011-06-01 21:53:57 +02:00
Wolfgang Denk
cd6881b519 Minor coding style cleanup.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-05-19 22:22:44 +02:00
Ben Gardiner
7124015ada README.arm-relocation: get relocated address in gdb
When your emulator is connected at reset (or is used to load u-boot)
it is possible to get the relocation address from the gd->relocaddr
since gd is always in r8 (on ARM) it is addressable before the
gdb has remapped symbols.

Document this alternate method in-line with the original method
written by Heiko Schocher.

Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Heiko Schocher <hs@denx.de>
CC: Wolfgang Denk <wd@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2011-05-12 23:34:02 +02:00
Ben Gardiner
f4379ceff0 README.arm-relocation: get relocated address from bdinfo
The bdinfo command prints the relocaddr on ARM as it does
on PPC.

Update the debugging instructions for arm relocation to
reflect this fact rather than requiring that the user
rebuild the u-boot image using -DDEBUG.

Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Wolfgang Denk <wd@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2011-05-12 23:33:32 +02:00
Eric Bénard
25ee9616de mp2usb: finish the removal
- remove from boards.cfg
- add to doc/README.scrapyard

Signed-off-by: Eric Bénard <eric@eukrea.com>
2011-05-12 23:28:40 +02:00
Timur Tabi
a5dbdc81ea video: parse the video-mode environment variable
Add function video_get_video_mode(), which parses the "video-mode" environment
variable and returns each of its components.  The format matches the video=
command-line option used for Linux:

	video-mode=<driver>:<xres>x<yres>-<depth>@<freq><,option=string>

	<driver> The video driver, ignored by U-Boot
	<xres> The X resolution (in pixels) to use.
	<yres> The Y resolution (in pixels) to use.
	<depth> The color depth (in bits) to use.
	<freq> The frequency (in Hz) to use.
	<options> A comma-separated list of device-specific options

Signed-off-by: Timur Tabi <timur@freescale.com>
2011-04-28 21:31:02 +02:00
Graeme Russ
b3acbb221d x86: Update MAINTAINERS and delete README files
The README files are totally out-of-date to the point where they do more
harm than good

Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
2011-04-13 19:43:30 +10:00
Graeme Russ
fea2572001 x86: Rename i386 to x86
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
2011-04-13 19:43:28 +10:00
Wolfgang Denk
17e967b3df Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2011-04-10 21:24:40 +02:00
Jiang Yutang
b93f81a418 powerpc/85xx: Add support usb2/etsec and tdm/audio pin multiplex on P1022DS
For soc which have pin multiplex relation, some of them can't enable
simultaneously. This patch add environment var 'hwconfig' content
defination for them. you can enable some one function by setting
environment var 'hwconfig' content and reset board. Detail setting
please refer doc/README.p1022ds

Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-10 11:17:55 -05:00
Timur Tabi
6c7a29a5b4 p4080ds: add README.p4080ds which documents the "serdes" hwconfig option
Add documentation for the "serdes" hwconfig option, which is used to
specify the status of SerDes banks two and three for the SERDES8 erratum
work-around.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-10 11:17:32 -05:00
Andreas Schallenberg
2fc32deab5 Blackfin: dnp5370: new board port
Info about the hardware can be found here:
	http://www.dilnetpc.com/dnp0086.htm

Signed-off-by: Andreas Schallenberg <Andreas.Schallenberg@3alitydigital.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08 00:44:26 -04:00
Daniel Schwierzeck
b38a569901 MIPS: Purple: Remove Purple support
The Purple SoC and eval board are not actively maintained since years.
This patch removes the support completely as aggreed with Wolfgang Denk.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
2011-04-02 22:07:12 +09:00
Wolfgang Denk
14666418e9 Coding Style cleanup: remove trailing empty lines
Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-03-27 21:48:08 +02:00
Simon Glass
89d48367ed Add USB host ethernet adapter support
This adds support for using USB Ethernet dongles in host mode. This is just
the framework - drivers will come later. A new config option called
CONFIG_USB_HOST_ETHER can be defined in board config files to switch this
on.

The was originally written by NVIDIA and was cleaned up for release by the
Chromium authors.

Signed-off-by: Simon Glass <sjg@chromium.org>
2011-02-19 20:32:36 +01:00
Wolfgang Denk
4bfa18fb99 Merge branch 'master' of git://git.denx.de/u-boot-sh 2011-02-04 20:38:27 +01:00
Wolfgang Denk
d1a24f0618 Minor Coding Style Cleanup.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-02-02 22:36:10 +01:00
Yoshihiro Shimoda
8e9c897b21 sh: add support for sh7757lcr board
The R0P7757LC0030RL board has SH7757, 256MB DDR3-SDRAM, SPI ROM,
Ethernet, and more.

This patch supports the following functions:
 - 256MB DDR3-SDRAM
 - SPI ROM
 - Ethernet

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2011-02-02 16:38:41 +09:00
Mike Rapoport
36b4e2dddd OMAP3: add CM-T35 board
This patch adds support for CM-T35 board

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-02-02 00:54:43 +01:00
Stefano Babic
eae4988b45 Add support for Freescale's mx35pdk board.
The patch adds suupport for the Freescale's mx35pdk board
(known as well as mx35_3stack).

The board boots from the NOR flash. Following devices
are supported:
 - two ethernet devices (FEC and SMC911x on debug board)
 - I2C
 - PMIC (MC13892) via I2C interface
 - UART
 - NOR flash (64MB)
 - NAND flash (2GB)
 - basic access to mc9sdz60 registers via I2C interface

Signed-off-by: Stefano Babic <sbabic@denx.de>
2011-02-02 00:54:43 +01:00
Liu Hui-R64343
8a1edd7d54 imximage: Add MX53 boot image support
This patch add the MX53 boot image support.

This patch has been tested on Freescale MX53EVK board
and MX51EVK board.

Signed-off-by: Jason Liu <r64343@freescale.com>
2011-02-02 00:54:42 +01:00
Wolfgang Denk
5aebe3b072 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2011-01-25 21:13:04 +01:00
York Sun
e1fd16b6f5 mpc85xx: Enable unique mode registers and dynamic ODT for DDR3
Added fsl_ddr_get_version() function to for DDR3 to poll DDRC IP version
(major, minor, errata) to determine if unique mode registers are available.
If true, always use unique mode registers. Dynamic ODT is enabled if needed.
The table is documented in doc/README.fsl-ddr. This function may also need
to be extend for future other platforms if such a feature exists.

Enable address parity and RCW by default for RDIMMs.

Change default output driver impedance from 34 ohm to 40ohm. Make it 34ohm for
quad-rank RDIMMs.

Use a formula to calculate rodt_on for timing_cfg_5.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19 22:58:23 -06:00
York Sun
47df8f03f4 mpc8xxx: Enable ECC on/off control in hwconfig
Add fsl_ddr:ecc=on in hwconfig. If ECC is enabled in board configuration file,
ECC can be turned on/off by this switch. If this switch is omitted, it is ON by
default.

Updated hwconfig calls to use local buffer.

Syntax is
hwconfig=fsl_ddr:ecc=on

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19 22:58:23 -06:00
Loïc Minier
3f1266d6d5 Escape minus signs in manpage
By default, "-" chars are interpreted as hyphens (U+2010) by groff, not
as minus signs (U+002D). Since options to programs use minus signs
(U+002D), this means for example in UTF-8 locales that you cannot cut
and paste options, nor search for them easily.

(Reported by lintian.)

Signed-off-by: Loc Minier <loic.minier@linaro.org>
2011-01-19 00:07:51 +01:00
Heiko Schocher
466f0137e8 mpc5200, digsy_mtc: add support for rev5 board version
difference to previous board version:
- M29W128GH flash from Numonyx
- SDRAM ISSI IS45S16800 (Option A2 105°C)
- rev5 uses RTC RV-3029-C2
- update cs0 and cs1 baseaddr and length
  depending on the detected flash size.
- added Werner Pfister <Pfister_Werner@intercontrol.de>
  as maintainer for the digsy board variants
- As the M29W128GH needs a special flash_cmd_reset()
  document that in the new file doc/README.cfi.
- move "#endif /* CONFIG_CMD_IDE */" to the right place
- remove LOWBOOT config option for digsy_mtc and digsy_mtc_rev5
  boards
- change doc/README.cfi as Stefan Roese suggested

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
cc: Wolfgang Denk <hs@denx.de>
cc: Stefan Roese <sr@denx.de>
cc: Werner Pfister <Pfister_Werner@intercontrol.de>
cc: Detlev Zundel <dzu@denx.de>
2011-01-18 23:34:26 +01:00
Becky Bruce
810c442749 85xx boards: Rename CONFIG_DDR_DLL to CONFIG_SYS_FSL_ERRATUM_DDR_MSYNC_IN
This config option is for an erratum workaround; rename it to be more
clear.  Also, drop it from config files don't need it and were
undefining it.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:19 -06:00
Kumar Gala
d761fa6205 powerpc/85xx: Removed support for ATUM8548 board
The ATUM8548 board is no longer maintained and thus we are removing
support for it.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:17 -06:00
Sughosh Ganu
48571ff005 Add board support for hawkboard
The patch adds basic board support for TI's OMAP-L138 based
Hawkboard. This board is pretty similar to the da850 EVM. Support for
nand and network access is added in this version.

The following bootup procedure is used.

At reset, the Rom Boot Loader(RBL), initialises the ddr and the nand
controllers and copies the second stage bootloader(nand_spl) to
RAM. The secondary bootloader then copies u-boot from a predefined
location in the nand flash to the RAM, and passes control to the
u-boot image.

Three config options are supported
* hawkboard_config - Used to create the u-boot.bin. Tftp the
 u-boot.bin image to the RAM from u-boot, and flash to the nand flash
 at address 0xe0000.

* hawkboard_nand_config - Used to generate the secondary
 bootloader(nand_spl) image. This creates an elf file u-boot-spl
 under nand_spl/. Create an AIS signed image using this file, and
 flash it to the nand flash at address 0x20000. The ais file should
 fit in one block.

* hawkboard_uart_config - This is same as the first image, but with
 the TEXT_BASE as expected by the RBL(0xc1080000). Create the AIS

Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-30 11:25:01 -05:00
Wolfgang Denk
afaa27bdd6 barco: drop unsupported board configuration
The barco board appears to be unmaintained since it was added about 5
years ago. The environment location has probably never been correct.
Drop it.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Marc Leeman <marc.leeman@barco.com>
Acked-by: Stefan Roese <sr@denx.de>
2010-11-26 22:08:18 +01:00
Wolfgang Denk
93b1140090 ERIC: drop unsupported board configuration
The ERIC board appears to be unmaintained for more than 9 years. The
environment location has probably never been correct, and has been
definitely broken since for at least a year.  Drop it.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Swen Anderson <sand@peppercon.de>
Acked-by: Stefan Roese <sr@denx.de>
2010-11-26 22:08:17 +01:00
Sekhar Nori
4f6fc15b42 DA850 EVM: passing maximum clock rate information to kernel
The TI DA850/OMAP-L138/AM18x EVM can be populated with devices
having different maximum allowed CPU clock rating.

The maximum clock the chip can support can only be determined from
the label on the package (not software readable).

Introduce a method to pass the maximum allowed clock rate information
to kernel using ATAG_REVISION. The kernel uses this information to
determine the maximum cpu clock rate reachable using cpufreq.

Note that U-Boot itself does not set the CPU clock rate. The CPU
clock is setup by a primary bootloader ("UBL"). The rate setup by
UBL could be different from the maximum clock rate supported by the
device.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-19 16:29:11 -05:00
Sekhar Nori
718f746427 DA850 EVM: add information regarding DA850 in README.davinci
The README.davinci in documentation folder is missing information
regarding DA850 which is a supported DaVinci device.

Add this information.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-19 16:29:06 -05:00
Wolfgang Denk
a9aa392629 Drop support for CONFIG_SYS_ARM_WITHOUT_RELOC
When this define was introduced, the idea was to provide a soft
migration path for ARM boards to get adapted to the new relocation
support.  However, other recent changes led to a different
implementation (ELF relocation), where this no longer works.  By now
CONFIG_SYS_ARM_WITHOUT_RELOC does not only not help any more, but it
actually hurts because it obfuscates the actual code by sprinkling it
with lots of dead and non-working debris.

So let's make a clean cut and drop CONFIG_SYS_ARM_WITHOUT_RELOC.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2010-10-29 21:39:59 +02:00
Wolfgang Denk
2e5167ccad Replace CONFIG_RELOC_FIXUP_WORKS by CONFIG_NEEDS_MANUAL_RELOC
By now, the majority of architectures have working relocation
support, so the few remaining architectures have become exceptions.
To make this more obvious, we make working relocation now the default
case, and flag the remaining cases with CONFIG_NEEDS_MANUAL_RELOC.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2010-10-29 21:32:07 +02:00
Wolfgang Denk
071bc92330 Coding Style cleanup
Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-27 22:48:30 +02:00
Wolfgang Denk
26fe3d2b8f VoVPN-GW_100MHz: drop unsupported board configuration
The 100MHz configuation of the VoVPN-GW has never been supported, so
drop it now.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-24 15:46:08 +02:00
Wolfgang Denk
f2b382ea06 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2010-10-23 21:59:42 +02:00
Peter Tyser
9d921f19b3 post/i2c: Add ability to ignore I2C devices
Add the ability to not report an I2C POST error for a set of given I2C
addresses on bootup.  This is useful for cases when a device may or may
not be present, and neither case is considered an error.  For example:

- Some form factors such as XMC and Compact PCI Express have an I2C
  EEPROM whose address changes based on geographical address.  Eg
  installed in one slot its EEPROM address is, 0x50, in another its
  0x51, etc.  This allows multiple devices to have their EEPROMs present
  on the same I2C bus.  Thus the I2C devices present for an XMC or
  CPCIe card depend on if and where other cards are installed in the
  same system.

- Some cards have optional I2C devices.  Eg one hardware build
  configuration has different I2C devices than another and software
  can't determine if the optional device should be present or not.

- Some cards have optional daughtercards with I2C devices on them.

- I2C EEPROMs address range depends on their size.  Its possible to
  support differently size EEPROMs by only probing the EEPROM's base
  address and ignoring the other addresses that are impacted by its
  size.

A new CONFIG_SYS_POST_I2C_IGNORES define has been added which specifies
a list of I2C addresses for the I2C POST to ignore.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-22 02:19:14 -05:00
Peter Tyser
60aaaa0782 post/i2c: Rename I2C_ADDR_LIST to CONFIG_SYS_POST_I2C_ADDRS
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-22 02:19:00 -05:00
Ilya Yanok
e03e4b7312 led_display: remove unused DISPLAY_MARK define
DISPLAY_MARK subcommand of display_set() is not used anywhere so
we can remove it safely.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
2010-10-21 22:25:04 +02:00
York Sun
ebbe11dd36 Add memory test feature for mpc85xx POST.
The memory test is performed after DDR initialization when U-boot stills runs
in flash and cache. On recent mpc85xx platforms, the total memory can be more
than 2GB. To cover whole memory, it needs be mapped 2GB at a time using a
sliding TLB window. After the testing, DDR is remapped with up to 2GB memory
from the lowest address as normal.

If memory test fails, DDR DIMM SPD and DDR controller registers are dumped for
further debugging.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-20 02:28:00 -05:00
Wolfgang Denk
b18815752f Merge branch 'master' of git://git.denx.de/u-boot-arm 2010-10-20 00:10:07 +02:00
Stefan Roese
ae8082c7e0 Add UBI README
This patch adds a small README to describe the usage of the
U-Boot UBI commands.

Signed-off-by: Stefan Roese <sr@denx.de>
2010-10-19 23:53:45 +02:00
Wolfgang Denk
923527aace doc/README.scrapyard: add documentation for abandoned boards
Add a document to maintain a list of boards removed from the current
source tree, so archeologists can check more easily if here is
something they might want to dig for...

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-19 21:46:25 +02:00
Wolfgang Denk
6d8d4ef994 Merge branch 'elf_reloc'
Conflicts:
	arch/arm/include/asm/config.h
	board/LaCie/edminiv2/config.mk
	board/karo/tx25/config.mk
	board/logicpd/imx27lite/config.mk
	doc/README.arm-relocation

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-19 21:07:52 +02:00
Wolfgang Denk
c8d76eaf60 Rename TEXT_BASE: fix merge conflicts
Commit 14d0a02a "Rename TEXT_BASE into CONFIG_SYS_TEXT_BASE" missed a
few places, especially for boards that were added inbetween. Fix the
remaining issues.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-18 23:48:15 +02:00
Wolfgang Denk
2ae1824196 Makefile: move all Power Architecture boards into boards.cfg
Clean up Makefile, and drop a lot of the config.mk files on the way.

We now also automatically pick all boards that are listed in
boards.cfg (and with all configurations), so we can drop the redundant
entries from MAKEALL to avoid building these twice.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-18 22:12:04 +02:00
Wolfgang Denk
14d0a02a16 Rename TEXT_BASE into CONFIG_SYS_TEXT_BASE
The change is currently needed to be able to remove the board
configuration scripting from the top level Makefile and replace it by
a simple, table driven script.

Moving this configuration setting into the "CONFIG_*" name space is
also desirable because it is needed if we ever should move forward to
a Kconfig driven configuration system.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-18 22:07:10 +02:00
Albert Aribaud
92d5ecba47 arm: implement ELF relocations
ELF relocation tables generated with linker option -pie can
be used to fixup code and data in a single loop at relocation,
removing the need for manual fixups anywhere else in the code.

Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
2010-10-13 10:10:21 +02:00
Ilya Yanok
7f0d241d5c led_display: split led display support into generic and hw-dependent parts
Split the display command into generic interface and hardware-specific
realization for PDSP188x LED display found on hmi1001 and manroland
boards. Simple interface for LED displays is defined in
include/led-display.h and described in doc/README.LED_display.
Driver-specific implementation was moved into drivers/misc/pdsp188x.c
file (enabled with CONFIG_PDSP188x set).

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
2010-10-12 22:44:33 +02:00
Timur Tabi
a2d12f8812 p1022ds: add audclk hwconfig setting to enable codec reference clock
The Freescale P1022DS can use either a 12.288MHz or a 11.2896MHz reference
clock for the audio codec, but by default both are disabled.  Add a 'audclk'
hwconfig option that allows the user to choose which clock he wants.

The 12.288MHz clock allows the codec to use sampling rates of 16, 24, 32, 48,
64, and 96KHz.  The 11.2896 clock allows 14700, 22050, 29400, 44100, 58800, and
88200Hz.

Also configure a pin muxing to select some SSI signals, which will disable
I2C1.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-07 09:49:47 -05:00
Wolfgang Denk
d483a22eca CONFIG_SYS_ARM_WITHOUT_RELOC: document feature removal
Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-04 10:56:25 +02:00
Stefan Roese
24956642ef Remove unused CONFIG_SERIAL_SOFTWARE_FIFO feature
This patch removes the completely unused CONFIG_SERIAL_SOFTWARE_FIFO
feature from U-Boot. It has only been implemented for PPC4xx and was not
used at all. So let's remove it and make the code smaller and cleaner.

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
2010-09-23 09:02:05 +02:00
Heiko Schocher
ab86f72c35 ARM: implement relocation for ARM926
Change the implementation for arm926 to relocate the code to
an arbitrary address in RAM.

Adapt the TX25 (i.MX25), magnesium board to test the changes.

On the tx25 board TEXT_BASE is set to the final relocation
address to prevent one more copying of u-boot code
when relocating. More info see:
doc/README.arm-relocation

da850 board:
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>

Portions of this work were supported by funding from
the CE Linux Forum.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
2010-09-19 19:29:54 +02:00
Heiko Schocher
f1d2b313c9 ARM: add relocation support
!! This breaks support for all arm boards !!

To compile in old style, you must define
CONFIG_SYS_ARM_WITHOUT_RELOC or you can compile
with "CONFIG_SYS_ARM_WITHOUT_RELOC=1 ./MAKEALL board"

!! This define will be removed soon, so convert your
board to use relocation support

Portions of this work were supported by funding from
the CE Linux Forum.

Signed-off-by: Heiko Schocher <hs@denx.de>

Fix boot from NAND for non-ARM systems
Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-09-19 19:29:53 +02:00
Wolfgang Denk
2d941de9d5 Prepare v2010.09-rc1
Coding style cleanup.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-09-10 00:16:19 +02:00
Reinhard Meyer
1592ef8596 AT91: MCI: add SD/MMC driver using mmc framework
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2010-09-03 11:19:01 +02:00
Wolfgang Denk
b9d51fbb18 Merge branch 'master' of git://git.denx.de/u-boot-arm 2010-08-10 23:03:15 +02:00
Wolfgang Denk
fe8d63c8c7 Merge branch 'master' of git://git.denx.de/u-boot-marvell 2010-08-10 22:37:27 +02:00
Kim Phillips
78b7a8ef8b net: rename "FSL UECx" net interfaces "UECx"
continuation of commit 2ecc2262d66a286e3aac79005bcb5f461312dea8
"net ppc: fix ethernet device names with spaces" (currently in
u-boot-net.git) for QE based parts.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-08-09 11:52:29 -07:00
Heiko Schocher
48690d8024 net ppc: fix ethernet device names with spaces
since commit 1384f3bb8a ethernet names
with spaces drop a

Warning: eth device name has a space!

message. This patch fix it for:

- "FEC ETHERNET" devices found on
  mpc512x, mpc5xxx, mpc8xx and mpc8220 boards.
  renamed to "FEC".
- "SCC ETHERNET" devices found on
  mpc8xx, mpc82xx based boards. Renamed to "SCC".
- "HDLC ETHERNET" devices found on mpc8xx boards
  Renamed to "HDLC"
- "FCC ETHERNET" devices found on mpc8260 and mpc85xx based
  boards. Renamed to "FCC"

Tested on the kup4k board.

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-08-09 11:52:28 -07:00
Nobuhiro Iwamatsu
cd1535564c Add mkimage manpage
Some Linux distributions include the "mkimage" as a package.
This commit provides a manual page for mkimage.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Added documentation for FIT images and examples.
Moved to doc/ directory.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-08-08 21:14:37 +02:00
Albert Aribaud
f2a37fcd9b ide: add configuration
CONFIG_IDE_SWAP_IO

This configuration option replaces a complex conditional
in cmd_ide.c with an explicit define to be added to SoC or
board configs.

Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
2010-08-08 05:17:05 +05:30
york
7fd101c97b powerpc/8xxx: Enabled address hashing for 85xx
For 85xx silicon which supports address hashing, it can be activated by
hwconfig.

Signed-off-by: York Sun <yorksun@freescale.com>
2010-07-26 13:16:09 -05:00
york
076bff8f47 powerpc/8xxx: Fix bug in memctrl interleaving & bank interleaving on cs0~cs4
Verified on MPC8641HPCN with four DDR2 dimms. Each dimm has dual
rank with 512MB each rank.

Also check dimm size and rank size for memory controller interleaving

Signed-off-by: York Sun <yorksun@freescale.com>
2010-07-26 13:16:09 -05:00
Kumar Gala
79e4e6480b powerpc/8xxx: Enabled hwconfig for memory interleaving
Replace environmental variables memctl_intlv_ctl and ba_intlv_ctl with
hwconfig parameters. The syntax is

    setenv hwconfig "fsl_ddr:ctlr_intlv=<mode>,bank_intlv=<mode>"

The mode values for memory controller interleaving are
    cacheline
    page
    bank
    superbank

The mode values for bank interleaving are
    cs0_cs1
    cs2_cs3
    cs0_cs1_and_cs2_cs3
    cs0_cs1_cs2_cs3

Signed-off-by: York Sun <yorksun@freescale.com>
2010-07-26 13:16:08 -05:00
Vipin KUMAR
5b1b1883ff SPEAr : Network driver support added
Designware network driver support added.
This is a Synopsys ethernet controller

Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-07-12 00:08:05 -07:00
Wolfgang Denk
54841ab50c Make sure that argv[] argument pointers are not modified.
The hush shell dynamically allocates (and re-allocates) memory for the
argument strings in the "char *argv[]" argument vector passed to
commands.  Any code that modifies these pointers will cause serious
corruption of the malloc data structures and crash U-Boot, so make
sure the compiler can check that no such modifications are being done
by changing the code into "char * const argv[]".

This modification is the result of debugging a strange crash caused
after adding a new command, which used the following argument
processing code which has been working perfectly fine in all Unix
systems since version 6 - but not so in U-Boot:

int main (int argc, char **argv)
{
	while (--argc > 0 && **++argv == '-') {
/* ====> */	while (*++*argv) {
			switch (**argv) {
			case 'd':
				debug++;
				break;
			...
			default:
				usage ();
			}
		}
	}
	...
}

The line marked "====>" will corrupt the malloc data structures and
usually cause U-Boot to crash when the next command gets executed by
the shell.  With the modification, the compiler will prevent this with
an
	error: increment of read-only location '*argv'

N.B.: The code above can be trivially rewritten like this:

	while (--argc > 0 && **++argv == '-') {
		char *arg = *argv;
		while (*++arg) {
			switch (*arg) {
			...

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2010-07-04 23:55:42 +02:00
Thomas Chou
1117cbf2ad nios: remove nios-32 arch
The nios-32 arch is obsolete and broken. So it is removed.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
2010-05-28 10:56:04 -04:00
Thomas Chou
0df01fd3d7 nios2: fix r15 issue for gcc4
The "-ffixed-r15" option doesn't work well for gcc4. Since we
don't use gp for small data with option "-G0", we can use gp
as global data pointer. This allows compiler to use r15. It
is necessary for gcc4 to work properly.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
2010-05-28 10:56:03 -04:00
Wolfgang Denk
445093d175 Fix "par[t]ition" typo.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-05-21 22:05:05 +02:00
Ben Warren
ecee9324d7 Program net device MAC addresses after initializing
Add a new function to the eth_device struct for programming a network
controller's hardware address.

After all network devices have been initialized and the proper MAC address
for each has been determined, make a device driver call to program the
address into the device.  Only device instances with valid unicast addresses
will be programmed.

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Acked-by: Detlev Zundel <dzu@denx.de>
Tested-by: Prafulla Wadaskar <prafulla@marvell.com>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Thomas Chou <thomas@wytron.com.tw>
2010-05-03 14:52:49 -07:00
Stefan Roese
a47a12becf Move arch/ppc to arch/powerpc
As discussed on the list, move "arch/ppc" to "arch/powerpc" to
better match the Linux directory structure.

Please note that this patch also changes the "ppc" target in
MAKEALL to "powerpc" to match this new infrastructure. But "ppc"
is kept as an alias for now, to not break compatibility with
scripts using this name.

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Anatolij Gustschin <agust@denx.de>
2010-04-21 23:42:38 +02:00
Peter Tyser
6a8a2b7058 nios: Move cpu/nios/* to arch/nios/cpu/*
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-04-13 09:13:27 +02:00
Peter Tyser
e9a882803e i386: Move cpu/i386/* to arch/i386/cpu/*
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-04-13 09:13:26 +02:00
Peter Tyser
a414553485 m68k: Move cpu/$CPU to arch/m68k/cpu/$CPU
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-04-13 09:13:24 +02:00
Peter Tyser
84ad688473 arm: Move cpu/$CPU to arch/arm/cpu/$CPU
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-04-13 09:13:24 +02:00
Peter Tyser
8d1f268204 ppc: Move cpu/$CPU to arch/ppc/cpu/$CPU
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-04-13 09:13:16 +02:00
Peter Tyser
ea0364f1bb Move lib_$ARCH directories to arch/$ARCH/lib
Also move lib_$ARCH/config.mk to arch/$ARCH/config.mk

This change is intended to clean up the top-level directory structure
and more closely mimic Linux's directory organization.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-04-13 09:13:03 +02:00
Peter Tyser
03b7004dda Create CPUDIR variable
The CPUDIR variable points to the location of a target's CPU directory.
Currently, it is set to cpu/$CPU.  However, using $CPUDIR will allow for
more flexibility in the future.  It lays the groundwork for reorganizing
U-Boot's directory structure to support a layout such as:

  arch/$ARCH/cpu/$CPU/* (architecture with multiple CPU types)
  arch/$ARCH/cpu/*      (architecture with one CPU type)

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-04-13 09:12:59 +02:00
Andre Schwarz
1f2463d764 Add initial support for Matrix Vision mvSMR board based on MPC5200B.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
2010-04-10 00:06:05 +02:00
Minkyu Kang
abbe18c353 s5pc1xx: update the README file
Because adds support the GPIO Interface, README file is updated.

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2010-04-03 15:24:26 -05:00
Heiko Schocher
8e64d6efd8 net, doc: How to setup MAC address correctly
As this seems unclear, document how the flow of setting up
the MAC address is correct.

Signed-off-by: Heiko Schocher <hs@denx.de>

Text changed slightly, adding input from Mike Frysinger.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-03-31 15:13:32 +02:00
Felix Radensky
d5a64237d5 doc: Fix ramdisk examples in doc/uImage.FIT/multi.its
The ramdisk sections in doc/uImage.FIT/multi.its lack
load address and entry point properties. Using examples
from this file will result in unbootable image, u-boot
will issue the following error messages:

Can't get ramdisk subimage load address!
Ramdisk image is corrupt or invalid

This patch adds missing properties to ramdisk sections.

Signed-off-by: Felix Radensky <felix@embedded-sol.com>
2010-03-31 15:13:31 +02:00
Wolfgang Denk
a574cff121 ml300: remove support for broken, orphaned board
The ml300 board has a number of issues, but nobody cares about this
long-orphaned board any more.  Remove it.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Michal Simek <monstr@monstr.eu>
2010-03-28 00:18:58 +01:00
Wolfgang Denk
93910edb59 Prepare v2010.03-rc1
Coding style cleanup, update CHANGELOG.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-03-12 23:06:04 +01:00
Frans Meulenbroeks
3920bbedcf Fix MPC8536DS documentation
This patch corrects small mistake in the register list in
doc/README.mpc8536ds. These registers are 32 bits and this one starts
at ....c not ....e

When using the ...c address I can boot from sd, when using the ...e
address I cannot.

Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Acked-by: Hu Mingkai <B21284@freescale.com>
2010-03-12 00:15:55 +01:00
Heiko Schocher
ab68f4dd19 doc: add README for CONFIG_HWCONFIG option
Signed-off-by: Heiko Schocher <hs@denx.de>
2010-03-12 00:09:25 +01:00
Jens Scharsig
98250e8e17 prepare joining at91rm9200 into at91
* prepare joining at91 and at91rm9200
 * add modified copy of soc files to cpu/arm920t/at91 to make
   possible to compile at91rm9200 boards in at91 tree instead
   of at91rm9200
 * add header files with c structure defs for AT91 MC, ST and TC
 * the new cpu files are using at91 c structure soc access
 * please read README.soc-at91 for details

Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
2010-02-12 12:31:55 -06:00
Jens Scharsig
425de62d40 add new CONFIG_AT91_LEGACY
* add's the new temporary CONFIG_AT91_LEGACY to all board configs
 This will need for backward compatiblity, while change the SoC access
 to c structures. If CONFIG_AT91_LEGACY is defined, the deprecated
 SoC is used.

Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
2010-02-12 12:31:54 -06:00
Stefano Babic
8edcde5e4e mkimage: Add Freescale imx Boot Image support (imximage)
This patch adds support for "imximage" (MX Boot Image)
to the mkimage utility. The imximage is used on the Freescales's
MX.25, MX.35 and MX.51 processors.

Further details under doc/README.imximage.

This patch was tested on a Freescale mx51evk board.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-01-25 23:58:29 +01:00
Vipin KUMAR
6fffcdf8c8 SPEAr : Adding README.spear in doc
README.spear contains information about SPEAr architecture and
build options etc

Signed-off-by: Vipin <vipin.kumar@st.com>
2010-01-23 08:15:49 -06:00
Anton Vorontsov
2e95004deb mpc83xx: Add NAND boot support for MPC8315E-RDB boards
The core support for NAND booting is there already, so this patch
is pretty straightforward.

There is one trick though: top level Makefile expects nand_spl to
be in nand_spl/board/$(BOARDDIR), but we can fully reuse the code
from mpc8313erdb boards, and so to not duplicate the code we just
symlink nand_spl/board/freescale/mpc8315erdb to mpc8313erdb.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>

o silence make during ln echo
o update documentation
o and avoid:

$ ./MAKEALL MPC8315ERDB_NAND
Configuring for MPC8315ERDB board...
sdram.o: In function `fixed_sdram':
/home/r1aaha/git/u-boot/nand_spl/board/freescale/mpc8313erdb/sdram.c:72: undefined reference to `udelay'

by renaming udelay -> __udelay in the spirit of commit
3eb90bad65 "Generic udelay() with watchdog
support".

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2010-01-07 18:33:52 -06:00
Wolfgang Denk
2a49bf3149 Merge branch 'master' into next
Conflicts:
	board/esd/plu405/plu405.c
	drivers/rtc/ftrtc010.c

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-12-05 02:11:59 +01:00
Sandeep Paulraj
6406d6daea TI DaVinci: Adding a README for the DaVinci series of SOC's
Adding an initial README for the DaVinci series of SOC's

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2009-11-27 16:26:18 -06:00
Ira W. Snyder
824d82997f Fix example FIT image source files
The example FIT image source files do not compile with the latest dtc and
mkimage. The following error message is produced:

DTC: dts->dtb  on file "kernel.its"
Error: kernel.its 7:0 - 1:0 syntax error
FATAL ERROR: Unable to parse input tree
./mkimage: Can't read kernel.itb.tmp: Invalid argument

The FIT image source files are missing the "/dts-v1/;" directive at the
beginning of the file. Add the directive to the examples.

Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
2009-11-24 23:44:16 +01:00
Mike Frysinger
e5c5d9e083 clarify eth driver halt/recv steps
The dev->halt() func can be called at any time, and the dev->recv() func
does not need to use NetRxPackets[] when calling NetReceive().

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-11-09 10:40:39 -08:00
Wolfgang Denk
4946775c6d Coding Style cleanup; update CHANGELOG, prepare -rc1
Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-10-28 00:49:47 +01:00
Minkyu Kang
8bc4ee9e82 s5pc1xx: add support SMDKC100 board
Adds new board SMDKC100 that uses s5pc100 SoC

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com>
2009-10-13 21:13:55 -05:00
Luigi 'Comio' Mantellini
4ba31ab33a Rewrite the miiphybb (Bit-banged MII bus driver) in order to support an arbitrary number of mii buses.
This feature is useful when your board uses different mii buses for different
phys and all (or a part) of these buses are implemented via bit-banging mode.

The driver requires that the following macros should be defined into the board
configuration file:

CONFIG_BITBANGMII       - Enable the miiphybb driver
CONFIG_BITBANGMII_MULTI - Enable the multi bus support

If the CONFIG_BITBANGMII_MULTI is not defined, the board's config file needs
to define at least the following macros:

MII_INIT      - Generic code to enable the MII bus (optional)
MDIO_DECLARE  - Declaration needed to access to the MDIO pin (optional)
MDIO_ACTIVE   - Activate the MDIO pin as out pin
MDIO_TRISTATE - Activate the MDIO pin as input/tristate pin
MDIO_READ     - Read the MDIO pin
MDIO(v)       - Write v on the MDIO pin
MDC_DECLARE   - Declaration needed to access to the MDC pin (optional)
MDC(v)        - Write v on the MDC pin

The previous macros make the driver compatible with the previous version
(that didn't support the multi-bus).

When the CONFIG_BITBANGMII_MULTI is also defined, the board code needs to fill
the bb_miiphy_buses[] array with a record for each required bus and declare
the bb_miiphy_buses_num variable with the number of mii buses.
The record (struct bb_miiphy_bus) has the following fields/callbacks (see
miiphy.h for details):

char name[]            - The symbolic name that must be equal to the MII bus
                         registered name
int (*init)()          - Initialization function called at startup time (just
                         before the Ethernet initialization)
int (*mdio_active)()   - Activate the MDIO pin as output
int (*mdio_tristate)() - Activate the MDIO pin as input/tristate pin
int (*set_mdio)()      - Write the MDIO pin
int (*get_mdio)()      - Read the MDIO pin
int (*set_mdc)()       - Write the MDC pin
int (*delay)()         - Delay function
void *priv             - Private data used by board specific code

The board code will look like:

struct bb_miiphy_bus bb_miiphy_buses[] = {
 { .name = miibus#1, .init = b1_init, .mdio_active = b1_mdio_active, ... },
 { .name = miibus#2, .init = b2_init, .mdio_active = b2_mdio_active, ... },
 ...
int bb_miiphy_buses_num = sizeof(bb_miiphy_buses) /
                          sizeof(bb_miiphy_buses[0]);

Signed-off-by: Luigi 'Comio' Mantellini <luigi.mantellini@idf-hit.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-10-10 23:16:53 -07:00
Ben Warren
99dbd4efd6 Add information about return values of xxx_eth_register() in documentation
As discussed on mailing list, <0 indicates failure, >=0 indicates number
of interfaces found.

Also added blurb about private data

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-10-05 00:02:51 -07:00
Mike Frysinger
1f1e774ec6 document network driver framework
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-10-04 23:03:06 -07:00
Mingkai Hu
693a048d8a Add README.mpc8536ds
Add boot from NAND/eSDHC/eSPI description

Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-09-30 08:42:12 -05:00
Paul Gortmaker
dd9ca98f26 sbc8548: reclaim wasted sector in boot flash
By nature of being based off the MPC8548CDS board, this
board inherited an ENV_SIZE setting of 256k.  But since
it has a smaller flash device (8MB soldered on), it has
a native sector size of 128k, and hence the ENV_SIZE was
causing 2 sectors to be used for the environment.

By removing the unused sector, we can push TEXT_BASE up
closer to the end of address space and reclaim that
sector for any other application.  This also fixes the
mismatch between TEXT_BASE and MONITOR_LEN reported by
Kumar earlier.

Since this board also supports the ability to boot off
the 64MB SODIMM flash, this change is forward looking
with that in mind; i.e. the settings for MONITOR_LEN
and ENV_SIZE will work when the 512k sectors of the
SODIMM flash are used for alternate boot in the future.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-09-30 08:29:47 -05:00
Paul Gortmaker
bd42bbb858 sbc8548: replace README with completely new document
The previous README.sbc8548 was pretty much content-free. Replace
it with something that actually gives the end user some relevant
hardware details, and also lists the u-boot configuration choices.

Also in the cosmetic department, fix the bogus line in the Makefile
that was carried over from the SBC8560 Makefile, and the typo in
the sbc8548.c copyright.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-09-24 12:04:59 -05:00
Peter Tyser
3202d33169 Remove deprecated 'autoscr' command/variables
The more standard 'source' command provides identical functionality to
the autoscr command.

Environment variable names/values on the MVBC_P, MVBML7, kmeter1,
mgcoge, and km8xx boards are updated to no longer refernce 'autoscr'.

The 'autoscript' and 'autoscript_uname' environment variables are
also removed.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Acked-by: Heiko Schocher <hs@denx.de>
2009-09-22 23:03:24 +02:00
Mike Frysinger
1c20e4a9fb tools/netconsole: use ncb automatically if available
The standard netcat, while ubiquitous, doesn't handle broadcast udp packets
properly.  The local ncb util does however.  So if ncb can be located in
the standard locations, automatically use that instead.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-09-15 22:55:45 +02:00
Prafulla Wadaskar
aa0c7a86cd mkimage: Add Kirkwood Boot Image support (kwbimage)
This patch adds support for "kwbimage" (Kirkwood Boot Image)
image types to the mkimage code.

For details refer to docs/README.kwbimage

This patch is tested with Sheevaplug board

Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Ron Lee <ron@debian.org>

Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
2009-09-10 22:58:48 +02:00
Wolfgang Denk
3ea43ff773 Merge branch 'master' of git://git.denx.de/u-boot-arm 2009-09-07 23:12:46 +02:00
Frederik Kriewitz
c35d7cf071 Add support for the DevKit8000 board
This patch adds support for the DevKit8000 board.

Signed-off-by: Frederik Kriewitz <frederik@kriewitz.eu>
2009-09-05 01:33:14 +02:00
Robin Getz
c4db335c2e Blackfin: change global data register from P5 to P3
Since the Blackfin ABI favors higher scratch registers by default, use the
last scratch register (P3) for global data rather than the first (P5).
This allows the compiler's register allocator to use higher number scratch
P registers, which in turn better matches the Blackfin instruction set,
which reduces the size of U-Boot by more than 1024 bytes...

Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-09-02 05:14:02 -04:00
Poonam Aggrwal
728ece343e 85xx: Add support for P2020RDB board
The code base adds P1 & P2 RDB platforms support.
The folder and file names can cater to future SOCs of P1/P2 family.
P1 & P2 processors are 85xx platforms, part of Freescale QorIQ series.

Tested following on P2020RDB:
1. eTSECs
2. DDR, NAND, NOR, I2C.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-28 17:12:38 -05:00
Paul Gortmaker
c0d660fbbe mpc83xx: sbc8349 - make enabling PCI more user friendly
Prior to this commit, to enable PCI, you had to go manually
edit the board config header, which isn't really user friendly.
This adds the typical PCI make targets to the toplevel Makefile
in accordance with what is being done with other boards.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-08-21 17:09:21 -05:00
Paul Gortmaker
fe613cdd4e sbc8349: combine HRCW flash and u-boot image flash
Up to this point in time, the sbc8349 board was storing the u-boot
image in flash 2x.  One for the HRCW value at the beginning of
flash (0xff80_0000), and once close to the end of flash (0xfff8_0000)
for the actual image that got executed.

This moves the TEXT_BASE to be the beginning of flash, which makes
the second copy of the image redundant, and frees up the flash
from the end of the environment storage to the end of the flash
device itself.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-07-27 18:35:53 -05:00
Wolfgang Denk
10c7604d02 Prepare 2009.08-rc1
Update CHANGELOG, minor coding style fix.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-07-27 00:24:55 +02:00
Jens Scharsig
50217deeb0 new video driver for bus vcxk framebuffers
This patch adds a new video driver

* adds common bus_vcxk framebuffer driver

Signed-off-by: Jens Scharsig <esw@bus-elektronik.de>
[agust@denx.de: fixed lots of style issues before applying]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2009-07-26 13:17:21 +02:00
Wolfgang Denk
28958b8bea Coding Style cleanup; update CHANGELOG.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-07-23 22:23:23 +02:00
Robin Getz
1a32bf4188 Add DNS support
On 04 Oct 2008 Pieter posted a dns implementation for U-Boot.

http://www.mail-archive.com/u-boot-users@lists.sourceforge.net/msg10216.html
>
> DNS can be enabled by setting CFG_CMD_DNS. After performing a query,
> the serverip environment var is updated.
>
> Probably there are some cosmetic issues with the patch. Unfortunatly I
> do not have the time to correct these. So if anybody else likes DNS
> support in U-Boot and has the time, feel free to patch it in the main tree.

Here it is again - slightly modified & smaller:
  - update to 2009-06 (Pieter's patch was for U-Boot 1.2.0)
  - README.dns is added
  - syntax is changed (now takes a third option, the env var to store
    the result in)
  - add a random port() function in net.c
  - sort Makefile in ./net/Makefile
  - dns just returns unless a env var is given
  - run through checkpatch, and clean up style issues
  - remove packet from stack
  - cleaned up some comments
  - failure returns much faster (if server responds, don't wait for
    timeout)
  - use built in functions (memcpy) rather than byte copy.

Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Pieter Voorthuijsen <pieter.voorthuijsen@prodrive.nl>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-07-22 22:53:44 -07:00
Scott Wood
be33b046b5 Remove legacy NAND and disk on chip code.
Legacy NAND had been scheduled for removal.  Any boards that use this
were already not building in the previous release due to an #error.

The disk on chip code in common/cmd_doc.c relies on legacy NAND,
and it has also been removed.  There is newer disk on chip code
in drivers/mtd/nand; someone with access to hardware and sufficient
time and motivation can try to get that working, but for now disk
on chip is not supported.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-07-16 19:07:47 -05:00
Wolfgang Denk
87abce6e91 Merge branch 'master' of /home/wd/git/u-boot/master 2009-07-14 00:00:04 +02:00
Wolfgang Denk
c3ae126c2c Merge branch 'master' of git://git.denx.de/u-boot-arm 2009-07-13 23:45:02 +02:00
Sedji Gaouaou
5ccc2d99d6 at91: Introduction of at91sam9g10 SOC.
AT91sam9g10 is an ARM 926ej-s SOC. It is an evolution of the at91sam9261 with a
faster clock speed: 266/133MHz.

Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
2009-07-12 17:56:11 +02:00
Sedji Gaouaou
22ee647380 at91: Introduction of at91sam9g45 SOC.
AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz.
It embeds USB high speed host and device, LCD, DDR2 RAM, and a full set of
peripherals.

The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES.
On the board you can find 2 USART, USB high speed,
a 480*272 LG lcd, ethernet, gpio/joystick/buttons.

Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
2009-07-12 17:43:34 +02:00
Jon Smirl
c9969947a4 board support patch for phyCORE-MPC5200B-tiny
Add support for the Phytec phyCORE-MPC5200B-tiny.
Code originally from Pengutronix.de.
Created CONFIG_SYS_ATA_CS_ON_TIMER01 define for when IDE CS is on
Timer 0/1

Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
2009-07-10 23:21:32 +02:00
David Brownell
6e29ed8e57 davinci_nand: cleanup II (CONFIG_SYS_DAVINCI_BROKEN_ECC)
Remove CONFIG_SYS_DAVINCI_BROKEN_ECC option.  It's not just nasty;
it's also unused by any current boards, and doesn't even match the
main U-Boot distributions from TI (which use soft ECC, or 4-bit ECC
on newer chips that support it).

DaVinci GIT kernels since 2.6.24, and mainline Linux since 2.6.30,
match non-BROKEN code paths for 1-bit HW ECC.  The BROKEN code paths
do seem to partially match what MontaVista/TI kernels (4.0/2.6.10,
and 5.0/2.6.18) do ... but only for small pages.  Large page support
is really broken (and it's unclear just what software it was trying
to match!), and the ECC layout was making three more bytes available
for use by filesystem (or whatever) code.

Since this option itself seems broken, remove it.  Add a comment
about the MV/TI compat issue, and the most straightforward way to
address it (should someone really need to solve it).

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-07-07 17:58:01 -05:00
Wolfgang Denk
8e5e9b940c Coding style cleanup; update CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-07-07 22:35:02 +02:00
Alessandro Rubini
f7aa59b29a arm nomadik: allow Nand and OneNand to coexists
The evaluation kit has both Nand and OneNand, both drivers are there
and the two configurations only select a different default for the
jffs partition. This adds the OneNand driver and cleans up storage.

Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
2009-07-06 21:53:06 +02:00
Alessandro Rubini
ee1363f2da arm nomadik: rename board to nhk8815
This is an error in my side in the initial submission: nobody
calls it ""nmdk8815", it's "nomadik hardware kit", nhk8815, instead.

Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
2009-07-06 21:53:00 +02:00
Jean-Christophe PLAGNIOL-VILLARD
1b3b7c640d at91sam9263ek: add nor flash support
this will allow you to store use it for the env and to boot directly U-Boot from

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-21 16:18:11 +02:00
Wolfgang Denk
92afd368bb Merge branch 'next' of ../master 2009-06-14 22:05:42 +02:00
Wolfgang Denk
6b1f78ae6a Prepare v2009.06
Update CHANGELOG, fix minor coding stylke issue. Update Makefile.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-06-14 21:30:39 +02:00
Peter Tyser
2c7920afaf 83xx: Replace CONFIG_MPC83[0-9]X with MPC83[0-9]x
Use the standard lowercase "x" capitalization that other Freescale
architectures use for CPU defines to prevent confusion and errors

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-06-12 20:47:17 +02:00
Peter Tyser
0f89860494 83xx: Replace CONFIG_MPC83XX with CONFIG_MPC83xx
Use the standard lowercase "xx" capitalization that other Freescale
architectures use for CPU defines to prevent confusion and errors

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-06-12 20:47:17 +02:00
Tom Rix
7caa13fdd2 Fix a typo in the instructions on using omap3's gpio interface.
Using the example for reading a gpio, shows the problem.
NULL should be the gpio number.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
2009-06-12 20:45:47 +02:00
Tom Rix
0c872ecd01 OMAP3 Port kernel omap gpio interface.
Port version 2.6.27 of the linux kernel's omap gpio interface to u-boot.
The orignal source is in linux/arch/arm/plat-omap/gpio.c

See doc/README.omap3 for instructions on use.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-06-12 20:39:50 +02:00
Tom Rix
376aee78dd ZOOM2 Add initial support for Zoom2
Zoom2 is a new board from Texas Instruments and LogicPD

The logicpd web site is a good source for general information on this board.
Please start looking here if the below links are broken.
http://www.logicpd.com

This is a pdf of the product
http://www.logicpd.com/sites/default/files/1012659A_Zoom_OMAP34x-II_MDP_Brief.pdf
This is the product description web page
http://www.logicpd.com/products/development-kits/texas-instruments-zoom%E2%84%A2-omap34x-ii-mdp

This patch provides a zoom2 base target by copying zoom1 and by making some
obvious changes.

To configure, run
make omap3_zoom2_config

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-06-12 20:39:50 +02:00
Tom Rix
65fd21c80f LED Add documentation describing the status_led and colour led API.
This document describes the u-boot status LED API.
This allows common u-boot commands to use a board's leds to
provide status for activities like booting and downloading files.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-06-12 20:39:49 +02:00
Peter Tyser
0f89c54be9 i2c: Update references to individual i2c commands
The individual i2c commands imd, imm, inm, imw, icrc32, iprobe, iloop,
and isdram are no longer available so all references to them have been
updated to the new form of "i2c <cmd>".

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-06-12 20:39:46 +02:00
Peter Tyser
d48eb5131d i2c: Remove deprecated individual i2c commands
The following individual I2C commands have been removed: imd, imm, inm,
imw, icrc32, iprobe, iloop, isdram.

The functionality of the individual commands is still available via
the 'i2c' command.

This change only has an impact on those boards which did not have
CONFIG_I2C_CMD_TREE defined.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-06-12 20:39:46 +02:00
Haiying Wang
6e2aebc33f 85xx: Add README for MPC8569MDS
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-06-12 09:13:27 -05:00
Ben Warren
c404cc5884 Schedule removal of non-CONFIG_NET_MULTI net driver API
This will make CONFIG_NET_MULTI the only net driver configuration and
we'll be able to remove this option.

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-05-15 21:32:52 +02:00
Wolfgang Denk
c0a14aedc3 Update CHANGELOG, coding style cleanup. 2009-04-05 00:27:57 +02:00
Jean-Christophe PLAGNIOL-VILLARD
843a2654bc at91sam9: add watchdog support
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-04-04 20:42:19 +02:00
Peter Tyser
1cd300de5e tools/Makefile: Compile ncb when CONFIG_NETCONSOLE
Also conditionally add ncb.o to OBJ_FILES list

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-04-04 01:12:25 +02:00
unsik Kim
75eb82ec7c mflash: Initial mflash support
Mflash is fusion memory device mainly targeted consumer eletronic and
mobile phone.
Internally, it have nand flash and other hardware logics and supports
some different operation (ATA, IO, XIP) modes.

IO mode is custom mode for the host that doesn't have IDE interface.
(Many mobile targeted SoC doesn't have IDE bus)

This driver support mflash IO mode.

Followings are brief descriptions about IO mode.

1. IO mode based on ATA protocol and uses some custom command. (read
   confirm, write confirm)
2. IO mode uses SRAM bus interface.

Signed-off-by: unsik Kim <donari75@gmail.com>
2009-04-03 23:47:06 +02:00
Wolfgang Denk
8ddfe804c4 Merge branch 'master' of git://git.denx.de/u-boot-nand-flash 2009-04-03 22:48:05 +02:00
Scott Wood
99067b08f4 Noisily disable the legacy NAND subsystem.
Legacy NAND is marked for feature removal after April 2009 (i.e. this
upcoming release).  There are still several boards that reference it
(though many do so only for disk-on-chip support which has been silently
disabled for a while now).  These boards will now fail to build
with #error, though the code is still there if the user removes #error.

The plan is to remove the code outright in the next release, along with
any board code that refers to it (such as board/esd/common/auto_update.c).

Also, remove the legacy NAND API description from README.nand.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-04-03 15:27:26 -05:00
Wolfgang Denk
74de7aefd7 Add "source" command; prepare removal of "autoscr" command
According to the doc/feature-removal-schedule.txt, the "autoscr"
command will be replaced by the "source" command in approximately 6
months from now.

This patch prepares this change and starts a 6 month transition
period as follows:

- The new "source" command has been added, which implements exactly
  the same functionlaity as the old "autoscr" command before
- The old "autoscr" command name is kept as an alias for compatibility
- Command sequences, script files atc. have been adapted to use the
  new "source" command
- Related environment variables ("autoscript", "autoscript_uname")
  have *not* been adapted yet; these will be renamed resp. removed in
  a separate patch when the support for the "autoscr" command get's
  finally dropped.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-04-03 22:01:42 +02:00
Wolfgang Denk
78237df552 Add "GPL cleanup" task to feature-removal-schedule.txt
Announce removal of all non-GPL or GPL-incompatible files
after August 2009.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-04-03 22:00:56 +02:00
Wolfgang Denk
aaa0e0812f Merge branch 'master' of git://git.denx.de/u-boot-at91 2009-03-26 22:27:45 +01:00
Haavard Skinnemoen
8206bfae3a Merge branch 'mimc200' 2009-03-23 10:22:41 +01:00
Nicolas Ferre
df486b1fa3 at91: Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC.
AT91sam9g20 is an evolution of the at91sam9260 with a faster clock speed.

The AT91SAM9G20-EK board is an updated revision of the AT91SAM9260-EK board.
It is essentially the same, with a few minor differences.

Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/product_card.asp?part_id=4337

Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-22 14:48:16 +01:00
Mike Frysinger
6ff4137f2a doc/README.enetaddr: document proper MAC usage
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Ben Warren <biggerbadderben@gmail.com>
2009-03-20 22:39:09 +01:00
Yoshihiro Shimoda
ada9318252 sh: Add support 32-Bit Extended Address Mode to sh7785lcr
We can built 'make sh7785lcr_32bit_config'. And add new command "pmb"
for this mode. This command changes PMB for using 512MB system memory.

Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2009-03-12 23:58:30 +09:00
Haavard Skinnemoen
ea393eb1d6 Merge branch 'cleanups' into next 2009-02-23 10:27:15 +01:00
Wolfgang Denk
f15c6515fc Coding style cleanup; update CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-02-12 00:08:39 +01:00
Peter Tyser
5fc56b907d Add feature-removal-schedule.txt
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-02-11 23:21:07 +01:00
Wolfgang Denk
6c6e042ab3 Merge branch 'master' of git://git.denx.de/u-boot-arm 2009-02-01 21:38:07 +01:00
Larry Johnson
f20405e316 ppc4xx: Add variable "korat_usbcf" for Korat board
The new environment variable "korat_usbcf" selects the USB
port used by the Korat board's CompactFlash controller.

Signed-off-by: Larry Johnson <lrj@acm.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-01-29 10:55:56 +01:00
Dirk Behme
7379f45a7b OMAP3: Add Zoom1 board support
Support for Zoom MDK with OMAP3430. Details of Zoom MDK available here:
http://www.logicpd.com/products/devkit/ti/zoom_mobile_development_kit

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
2009-01-28 21:40:16 +01:00
Dirk Behme
2be2c6cc67 OMAP3: Add Pandora support
Add Pandora support.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
2009-01-28 21:39:58 +01:00
Dirk Behme
ad9bc8e52d OMAP3: Add EVM board
Add EVM board support.

Signed-off-by: Manikandan Pillai <mani.pillai@ti.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
2009-01-28 21:39:58 +01:00
Dirk Behme
9d0fc8110e OMAP3: Add Overo board
Add Overo board support.

Signed-off-by: Steve Sakoman <sakoman@gmail.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
2009-01-28 21:39:57 +01:00
Dirk Behme
f904cdbb68 OMAP3: Add common power code, README, and BeagleBoard
Add BeagleBoard support, common power code and README.

Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-01-28 21:39:15 +01:00
Wolfgang Denk
6450a84858 Update CHANGELOG, tiny coding style cleanup.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-01-28 00:29:26 +01:00
Alessandro Rubini
d5254f149d Initial support for Nomadik 8815 development board
The NMDK8815 board is distributed by ST Microelectornics.
Other (proprietary) code must be run to unlock the CPU before
U-Boot runs. doc/README.nmdk8815 outlines the boot sequence.

This is the initial port, with basic infrastructure and
a working serial port.

Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stnwireless.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-01-24 18:10:37 +01:00
Wolfgang Denk
8f86a3636e Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2009-01-24 02:17:02 +01:00
Wolfgang Denk
1ea0823786 Merge branch 'master' of git://git.denx.de/u-boot-mpc83xx 2009-01-24 02:08:31 +01:00
Shinya Kuribayashi
36ede4d63e nios: Move README.nios_CONFIG_SYS_NIOS_CPU to doc/ dir
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
2009-01-24 01:29:23 +01:00
Kim Phillips
833d94bcdc Merge branch 'next' 2009-01-23 17:48:24 -06:00
Heiko Schocher
de0443614a powerpc: 83xx: add support for the kmeter1 board
This patch adds support for the kmeter1 board from Keymile,
based on a Freescale MPC8360 CPU.

- serial console on UART 1
- 256 MB DDR2 RAM
- 64 MB NOR Flash
- Ethernet RMII Mode over UCC4
- PHY SMSC LAN8700

Signed-off-by: Heiko Schocher <hs@denx.de>
2009-01-24 00:36:19 +01:00
Haiying Wang
30837e5b21 Add README file for MPC8572DS board
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
2009-01-23 17:03:12 -06:00
Ron Madrid
5bb907a492 mpc83xx: New board support for SIMPC8313
This patch will create a new board, SIMPC8313, from Sheldon Instruments.  This
board boots from NAND devices and is configureable for either large or small
page devices.  The board supports non-soldered DDR2, one ethernet port, a
Marvell 88E1118 PHY, and PCI host support.  The board also has a FPGA connected
to the eLBC providing glue logic to a TMS320C67xx DSP.

Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-01-23 11:31:18 -06:00
Wolfgang Grandegger
6c869637fe NAND: rename NAND_MAX_CHIPS to CONFIG_SYS_NAND_MAX_CHIPS
This patch renames NAND_MAX_CHIPS to CONFIG_SYS_NAND_MAX_CHIPS and
changes the default from 8 to 1 for the legacy and the new MTD
NAND layer. This allows to remove all NAND_MAX_CHIPS definitions
in the board config files because none of the boards use multi
chip support (NAND_MAX_CHIPS > 1) so far. The bamboo and the DU440
define

 #define NAND_MAX_CHIPS          CONFIG_SYS_MAX_NAND_DEVICE

but that's bogus and did not work anyhow.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-01-23 10:32:51 -06:00
Kim Phillips
be4880ebe4 Merge branch 'master' into next 2009-01-21 18:38:51 -06:00
Nicolas Ferre
4e170b1662 at91: add at91sam9xeek board support
At91sam9xe is basically an at91sam9260 with embedded flash. We can manage
it as another entry for at91sam9260 in the Makefile.

Check documentation at :
http://www.atmel.com/dyn/products/product_card.asp?part_id=4263

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-01-06 21:37:19 +01:00
Haavard Skinnemoen
cb54732052 Merge branch 'fixes' into cleanups
Conflicts:

	board/atmel/atngw100/atngw100.c
	board/atmel/atstk1000/atstk1000.c
	cpu/at32ap/at32ap700x/gpio.c
	include/asm-avr32/arch-at32ap700x/clk.h
	include/configs/atngw100.h
	include/configs/atstk1002.h
	include/configs/atstk1003.h
	include/configs/atstk1004.h
	include/configs/atstk1006.h
	include/configs/favr-32-ezkit.h
	include/configs/hammerhead.h
	include/configs/mimc200.h
2008-12-17 16:53:07 +01:00
Jean-Christophe PLAGNIOL-VILLARD
b616f2b545 MIPS: qemu_mips: update doc to generate and to use qemu flash, ide file
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
2008-12-17 22:29:05 +09:00
Jean-Christophe PLAGNIOL-VILLARD
16cdf81677 MIPS: qemu_mips: update doc to use all disk and boot linux kernel
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
2008-12-17 22:28:41 +09:00
Mike Frysinger
bcb6dd9187 tools/netconsole: new script for working with netconsole over UDP
While the doc/README.NetConsole does have a snippet for people to
create their own netcat script, it's a lot easier to make a simple
dedicated script and tell people to use it.

Also spruce it up a bit to make it user friendly.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2008-12-10 09:23:11 +01:00
Wolfgang Denk
13d36ec849 Merge branch 'master' of git://git.denx.de/u-boot-at91 2008-12-09 01:06:14 +01:00
Gary Jennejohn
16a28ef219 IOMUX: Add console multiplexing support.
Modifications to support console multiplexing.  This is controlled using
CONFIG_SYS_CONSOLE_MUX in the board configuration file.

This allows a user to specify multiple console devices in the environment
with a command like this: setenv stdin serial,nc.  As a result, the user can
enter text on both the serial and netconsole interfaces.

All devices - stdin, stdout and stderr - can be set in this manner.

1) common/iomux.c and include/iomux.h contain the environment setting
implementation.
2) doc/README.iomux contains a somewhat more detailed description.
3) The implementation in (1) is called from common/cmd_nvedit.c to
handle setenv and from common/console.c to handle initialization of
input/output devices at boot time.
4) common/console.c also contains the code needed to poll multiple console
devices for input and send output to all devices registered for output.
5) include/common.h includes iomux.h and common/Makefile generates iomux.o
when CONFIG_SYS_CONSOLE_MUX is set.

Signed-off-by: Gary Jennejohn <garyj@denx.de>
2008-12-07 01:23:35 +01:00
Nicolas Ferre
89a7a87f08 at91: Choose environment variables location within make config target
This patch adds the possiblity to choose the media where the environment will
be located. This allow to choose this fundamental configuration without editing
config files.

Documentation file added.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Stelian Pop <stelian@popies.net>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-12-06 13:11:14 +01:00
Becky Bruce
29382d4064 mpc8641: Fix error in README
I made some updates to the code that didn't make it into the
README - fix this

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-12-01 10:28:52 -06:00
Heiko Schocher
fed36ac5ae powerpc: 83xx: add support for the kmeter1 board
This patch adds support for the kmeter1 board from Keymile,
based on a Freescale MPC8360 CPU.

- serial console on UART 1
- 256 MB DDR2 RAM
- 64 MB NOR Flash
- Ethernet RMII Mode over UCC4
- PHY SMSC LAN8700

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-11-20 15:29:32 -06:00
Becky Bruce
3111d32c49 mpc8641: Support 36-bit physical addressing
This patch creates a memory map with all the devices
in 36-bit physical space, in addition to the 32-bit map.
The CCSR relocation is moved (again, sorry) to
allow for the physical address to be 36 bits - this
requires translation to be enabled.  With 36-bit physical
addressing enabled, we are no longer running with VA=PA
translations.  This means we have to distinguish between
the two in the config file.  The existing region name is
used to indicate the virtual address, and a _PHYS variety
is created to represent the physical address.

Large physical addressing is not enabled by default.
Set CONFIG_PHYS_64BIT in the config file to turn this on.

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-11-10 10:10:05 -06:00
Becky Bruce
c759a01a00 mpc8641: Change 32-bit memory map
The memory map on the 8641hpcn is modified to look more like
the 85xx boards; this is a step towards a more standardized
layout going forward. As part of this change, we now relocate
the flash.

The regions for some of the mappings were far larger than they
needed to be.  I have reduced the mappings to match the
actual sizes supported by the hardware.

In addition I have removed the comments at the head
of the BAT blocks in the config file, rather than updating
them.  These get horribly out of date, and it's a simple
matter to look at the defines to see what they are set to
since everything is right here in the same file.

Documentation has been changed to reflect the new map, as this
change is user visible, and affects the OS which runs post-uboot.

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-11-10 10:10:04 -06:00
TsiChung Liew
536e7dac16 ColdFire: Add MCF5301x CPU and M53017EVB support
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
2008-11-03 09:45:58 -07:00
Bartlomiej Sieka
7c84fe6a06 Fix to the auto-update feature documentation (CONFIG_UPDATE_TFTP_MSEC_MAX)
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
2008-10-31 09:50:25 +01:00
Scott Wood
5cdade07b1 mpc8313erdb: Document NAND boot.
Previously, the documentation claimed that NAND boot is not supported.
This is no longer true.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-10-29 14:35:56 -05:00
Haiying Wang
c9ffd839b1 Check DDR interleaving mode
* Check DDR interleaving mode from environment by reading memctl_intlv_ctl and
ba_intlv_ctl.
* Print DDR interleaving mode information
* Add doc/README.fsl-ddr to describe the interleaving setting

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
2008-10-18 21:54:05 +02:00
Jean-Christophe PLAGNIOL-VILLARD
6d0f6bcf33 rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-10-18 21:54:03 +02:00
Bartlomiej Sieka
4bae90904b Automatic software update from TFTP server
The auto-update feature allows to automatically download software updates
from a TFTP server and store them in Flash memory during boot. Updates are
contained in a FIT file and protected with SHA-1 checksum.

More detailed description can be found in doc/README.update.

Signed-off-by: Rafal Czubak <rcz@semihalf.com>
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
2008-10-18 21:54:00 +02:00
Peter Tyser
abbb90666d Remove unused CFG_EEPROM_PAGE_WRITE_ENABLE references
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2008-10-14 14:45:31 +02:00