Commit graph

50351 commits

Author SHA1 Message Date
Michal Simek
5b410deac6 watchdog: cadence: Show used timeout value
Debug message was showing timeout value which was passed to start
function but there is a checking if this value can be setup.
The patch is moving this debug printf function below checking.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-11 09:23:43 +02:00
Michal Simek
e00656b2a9 arm64: zynqmp: Reset FPD Watchdog on zcu100
Low level configuration didn't reset FPD Watchdog that's why accessing
it caused u-boot hang.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-11 09:23:43 +02:00
Siva Durga Prasad Paladugu
9fdde6c4bb nand: zynq: Send address cycles as per onfi parameter page
Send address cycles as per value read from onfi parameter
page for Read and write commands instead of using a
hard coded value. This may vary for different parts and
hence use it from onfi parameter page value.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-11 09:23:43 +02:00
Siva Durga Prasad Paladugu
9ca8388059 nand: zynq: Add support for 16-bit buswidth
This patch adds support for 16-bit buswidth by determining
the bus width based on mio configuration.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-11 09:23:43 +02:00
Michal Simek
6de7a5b907 MAINTAINERS: zynqmp: Point to proper zynqmp folder
Point to Zynqmp arm64 cpu folder not to Zynq arm32.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-11 09:23:43 +02:00
Michal Simek
d93c666c4c serial: zynq: Remove header depedency on arm header structure
There is no need to have arm hardware header in this driver.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-11 09:23:43 +02:00
Michal Simek
72c37d1221 timer: Add Cadence TTC timer counter support
This driver was tested on Xilinx ZynqMP SoC.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-11 09:23:43 +02:00
Siva Durga Prasad Paladugu
83ec537dfb microblaze: Dont enable UBI support by default
This patch removes UBI support from defconfig and it can
be enabled from menuconfig as per need.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-11 09:23:43 +02:00
Siva Durga Prasad Paladugu
04ab29ab25 arm64: zynqmp: Add new defconfig for zc1275 revB
This patch enables support zc1275 revB board. It has
SD added compared to revA. The same configuration will
work for RevC boards aswell.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-11 09:23:43 +02:00
Michal Simek
c3898a8891 scsi: ceva: Convert driver to use UCLASS_AHCI instead of SCSI
In v2018 the patch
"dm: ahci: Correct uclass private data"
(sha1: bfc1c6b483)
was causing an issue for ceva_sata.
But this issue is not in v2018.05-rc1 but still converting to
UCLASS_AHCI would make more sense.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-11 09:23:43 +02:00
Michal Simek
0b4b82ad14 arm: zynq: Remove checkboard and enable DISPLAY_CPUINFO
Now that showing silicon version is part of the CPU
info display, let's remove checkboard().

Note that the generic show_board_info() will still
show the DT 'model' property. For instance:

U-Boot 2018.05-rc2-00025-g611b3ee0159b (Apr 19 2018 - 11:23:12 +0200)

CPU:   Zynq 7z045
Silicon: v1.0
Model: Zynq ZC706 Development Board
I2C:   ready

Based on patches from Ariel D'Alessandro <ariel@vanguardiasur.com.ar>,
and Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>

mini configuration doesn't need to show this information.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-11 09:23:43 +02:00
Michal Simek
4aba5fb857 arm: zynq: Rework FPGA initialization
This commit moves the FPGA descriptor definition
to mach-zynq, where it makes more sense.

Based on patches from Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
and Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-11 09:23:43 +02:00
Michal Simek
57213c5f37 arm: zynq: Enable debug_uart_init in spl when enabled
In past this code was commented and was used for debug purpose.
But there is no reason not to enabled it based on macros.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-11 09:23:43 +02:00
Tom Rini
3aba3fd654 Merge git://git.denx.de/u-boot-socfpga 2018-05-10 22:57:41 -04:00
Tom Rini
f739fcd831 SPDX: Convert a few files that were missed before
As part of the main conversion a few files were missed.  These files had
additional whitespace after the '*' and before the SPDX tag and my
previous regex was too strict.  This time I did a grep for all SPDX tags
and then filtered out anything that matched the correct styles.

Fixes: 83d290c56f ("SPDX: Convert all of our single license tags to Linux Kernel style")
Reported-by: Heinrich Schuchardt <xypron.debian@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-10 20:38:35 -04:00
Heinrich Schuchardt
b14619ba62 tools/file2include: avoid incorrect comments
Avoid creating incorrect comments like /* ...*/... */ by printing
'.' instead of '*' inside comments.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2018-05-10 20:38:34 -04:00
Heinrich Schuchardt
4a8e72954e include: update log2 header from the Linux kernel
Without the patch gcc 8 produces:
warning: ignoring attribute ‘noreturn’ because it conflicts with
attribute ‘const’ [-Wattributes]
 int ____ilog2_NaN(void);

So let's update the include from Linux kernel v4.16.

This removes static checks of ilog2() arguments.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2018-05-10 20:38:34 -04:00
Heinrich Schuchardt
23c648982b xyz-modem: va_start() must be matched by va_end()
Every va_start() call must be matched by a va_end() call.

scripts/checkpatch.pl required reformatting the complete function
zm_dprintf().

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2018-05-10 20:38:34 -04:00
Heinrich Schuchardt
e75ac7039a tools/file2include: create Linux style SPDX header
file2include is used to convert a binary file to a C include.
With the patch the SPDX header is written to the first line as
expected by scripts/checkpatch.pl.

Cf. https://www.kernel.org/doc/html/v4.16/process/license-rules.html

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-05-10 20:38:34 -04:00
Hannes Schmelzer
7f1cb1d588 bootm: fix 'memory-fixup' for vxWorks boot
The check for having a memory node within the fdt blob is made wrong, we
fix this here.

Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
2018-05-10 20:38:34 -04:00
Alex Kiernan
8140816eea Fix Ymodem build when DEBUG and CONFIG_USE_TINY_PRINTF are selected
Attempting to build with both DEBUG and CONFIG_USE_TINY_PRINTF along
with CONFIG_SPL_YMODEM_SUPPORT fails at link time:

  common/built-in.o: In function `zm_dprintf':
  common/xyzModem.c:190: undefined reference to `vsprintf'

Disable Ymodem debug if we don't have full vsprintf support.

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
2018-05-10 20:38:33 -04:00
Fabio Estevam
53deb24dda board/freescale: Remove invalid fsl email addresses
These fsl email addresses are no longer valid and they do not have a
correspondent nxp.com entry.

Remove all invalid fsl email addresses and mark the boards as orphan.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-05-10 20:38:33 -04:00
Fabio Estevam
ba74491e24 p1022ds: Change Timur's email address
timur@freescale.com is not a valid email for quite some time, so change
it to Timur's updated email.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Timur Tabi <timur@tabi.org>
2018-05-10 20:38:33 -04:00
Lukasz Majewski
4c0d0ffd4c bootcount: display5: config: Enable boot count feature in the display5 board
The boot count is enabled in both SPL and proper u-boot.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
2018-05-10 20:38:33 -04:00
Lukasz Majewski
2dbd5cd966 bootcount: display5: spl: Extend DISPLAY5 board SPL to support bootcount checking
This patch is necessary for providing basic bootcount checking in the case
of using "falcon" boot mode in that board.

It forces u-boot proper boot, when we exceed the number of errors.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
2018-05-10 20:38:32 -04:00
Lukasz Majewski
a8be249463 bootcount: spl: Extend SPL to support bootcount incrementation
This patch adds support for incrementation of the bootcount in SPL.
Such feature is necessary when we do want to use this feature with
'falcon' boot mode (which loads OS directly in SPL).

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-05-10 20:38:32 -04:00
Lukasz Majewski
bc8c440fa4 bootcount: Rewrite autoboot to use wrapper functions from bootcount.h
The code has been refactored to use common wrappers from bootcount.h
header.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Alex Kiernan <alex.kiernan@gmail.com>
2018-05-10 20:38:25 -04:00
Lukasz Majewski
0da7041218 bootcount: Add function wrappers to handle bootcount increment and error checking
Those two functions can be used to provide easy bootcount management.

Signed-off-by: Lukasz Majewski <lukma@denx.de>

Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2018-05-10 20:37:05 -04:00
Lukasz Majewski
c1cd21db62 bootcount: Add include guards into bootcount.h file
This patch adds missing include guards for bootcount.h file.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Alex Kiernan <alex.kiernan@gmail.com>
2018-05-10 20:37:05 -04:00
Lukasz Majewski
afa9609eca bootcount: spl: Enable bootcount support in SPL
New, SPL related config option - CONFIG_SPL_BOOTCOUNT_LIMIT has been
added to allow drivers/bootcount code re-usage in SPL.

This code is necessary to use and setup bootcount in SPL in the case of
falcon boot mode.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Alex Kiernan <alex.kiernan@gmail.com>
2018-05-10 20:37:05 -04:00
Marcel Ziswiler
71cb3d7c78 apalis_t30: fix optional pcie port reset for reliable pcie operation
Allow optionally bringing up the Apalis type specific 4 lane PCIe port
as well as the PCIe switch as found on the Apalis Evaluation board. In
order to avoid violating the PCIe reset timing do this by overriding the
tegra_pcie_board_port_reset() function. Note however that both the
Apalis type specific 4 lane PCIe port as well as the regular Apalis PCIe
port are also left disabled in the device tree by default.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2018-05-10 16:34:30 -07:00
Marcel Ziswiler
b4f9010428 apalis_t30: fix pcie port 0 and 1 pin muxing
Fix optional Apalis type specific 4 lane PCIe port 0 and Apalis PCIe
port 1 pin muxing.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2018-05-10 16:34:30 -07:00
Marcel Ziswiler
6ab8a2b0ee apalis_t30: describe pcie ports
Add some more comments describing the various PCIe ports available.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2018-05-10 16:34:30 -07:00
Marcel Ziswiler
f1333417e8 apalis-tk1: fix pcie reset for reliable gigabit ethernet operation
It turns out that the current PCIe reset implementation in the PCIe
board init function is not quite working reliably due to PCIe reset
timing violations. Fix this by overriding the
tegra_pcie_board_port_reset() function.

Also allow optionally bringing up the PCIe switch as found on the Apalis
Evaluation board. Note however that the Apalis PCIe port is also left
disabled in the device tree by default.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2018-05-10 16:34:21 -07:00
Marcel Ziswiler
de42975141 power: as3722: add as3722_ldo_set_voltage signature to header file
Just like the already present as3722_sd_set_voltage() add the currently
missing signature of the as3722_ldo_set_voltage() function to its header
file.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2018-05-10 16:34:21 -07:00
Marcel Ziswiler
355560d588 pci: tegra: introduce weak tegra_pcie_board_port_reset() function
Introduce a weak tegra_pcie_board_port_reset() function by default
calling the existing tegra_pcie_port_reset() function. Additionally add
a tegra_pcie_port_index_of_port() function to retrieve the specific PCIe
port index if required. This allows overriding the PCIe port reset
functionality from board specific code as e.g. required for Apalis T30
and Apalis TK1.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2018-05-10 16:34:21 -07:00
Marcel Ziswiler
4616e33b6a power: as3722: fix ldo_get/set_enable for ldo index bigger than 7
Fix ldo_get_enable() and ldo_set_enable() functions for LDOs with an
index > 7. Turns out there are actually two separate AS3722_LDO_CONTROL
registers AS3722_LDO_CONTROL0 and AS3722_LDO_CONTROL1. Actually make use
of both. While at it also actually use the enable parameter of the
ldo_set_enable() function which now truly allows disabling as opposed to
only enabling LDOs.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2018-05-10 16:34:20 -07:00
Marcel Ziswiler
c0cb8c8e86 apalis-tk1: add missing as3722 gpio0 configuration
As the AS3722 GPIO0 is also a not connected on our Apalis TK1 module
explicitly configure it to high-impedance as well.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2018-05-10 16:34:20 -07:00
Sanchayan Maity
1c1238f1e1 configs: apalis-tk1: fix boot failure using ext4 rootfs
Trying to boot from an ext4 rootfs fails due to us defaulting to ext3.
While the downstream T20/T30 L4T kernel has issues with ext4 later TK1
L4T should work just fine with it. Hence enable ext4 for sdboot and
usbboot on TK1.

Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2018-05-10 16:34:20 -07:00
Marcel Ziswiler
51cd5a147d configs: colibri_t20: enable mtd
Enable CONFIG_MTD as well to make sure UCLASS_MTD is available

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2018-05-10 16:34:10 -07:00
Marcel Ziswiler
fa91fda8c3 configs: harmony: enable live tree, mtd and ubi
U-Boot on Harmony recently got broken by ongoing driver model resp. live
tree migration work:

U-Boot 2018.03-rc3 (Feb 21 2018 - 15:43:08 +0100)

TEGRA20
Model: NVIDIA Tegra20 Harmony evaluation board
Board: NVIDIA Harmony
DRAM:  1 GiB
Video device 'dc@54200000' cannot allocate frame buffer memory -ensure
the device is set up before relocation
Error binding driver 'tegra_lcd': -28
Some drivers failed to bind
Error binding driver 'generic_simple_bus': -28
Some drivers failed to bind
initcall sequence 3ffa86d0 failed at call 00121dc0 (err=-28)

This commit fixes this by enabling live tree, MTD and UBI for Harmony as
well.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2018-05-10 16:34:10 -07:00
Marcel Ziswiler
4b11a6296a mtd: nand: tegra: convert to driver model and live tree
The Tegra NAND driver recently got broken by ongoing driver model resp.
live tree migration work:

NAND:  Could not decode nand-flash in device tree
Tegra NAND init failed
0 MiB

A patch for NAND uclass support was proposed about a year ago:
https://patchwork.ozlabs.org/patch/722282/

It was not merged and I do not see on-going work for this.

This commit just provides a driver model probe hook to retrieve further
configuration from the live device tree. As there is no NAND ulass as of
yet (ab)using UCLASS_MTD. Once UCLASS_NAND is supported, it would be
possible to migrate to it.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2018-05-10 16:34:10 -07:00
Tom Rini
da342f06b3 Merge git://git.denx.de/u-boot-ubi 2018-05-10 07:17:14 -04:00
Tom Rini
e8f80a5a58 Merge git://git.denx.de/u-boot-sunxi 2018-05-09 12:58:06 -04:00
Yogesh Gaur
a6f2a6eafe driver: net: fsl-mc: updated copyright info
Updated copyright info for the issues reported after running
check-legal test.

Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-05-09 09:17:51 -05:00
Jagdish Gediya
e8c669a3e6 mtd: nand: fsl_ifc: Fix nand waitfunc return value
As per the IFC hardware manual, Most significant byte in nand_fsr
register is the outcome of NAND READ STATUS command.

So status value need to be shifted as per the nand framework
requirement.

Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-05-09 09:17:51 -05:00
Hou Zhiqiang
8b40f22900 armv8/fsl-lsch2: make the workaround for PIN MUX erratum A010539 robust
Mask HRESET_B after cleared the the RCW_SRC, because in the workaround
we override the RCW_SRC and if HRESET_B is issued after the override
then SoC cannot find valid RCW as the RCW_SRC was overwritten and
result in hang. So we need to mask HRESET_B in case user asserts it,
and the PORESET_B should be asserted which leads to resampling of
cfg_rcw_src pins and loading of correct RCW_SRC.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-05-09 09:17:51 -05:00
Hou Zhiqiang
945fad57be armv8/fsl-lsch2: correct QMAN clock
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-05-09 09:17:51 -05:00
Sumit Garg
8044900a5b armv8: sec_firmware: Add support for multiple loadables
Enable support for multiple loadable images in SEC firmware FIT image.
Also add example "sec_firmware_ppa.its" file.

Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-05-09 09:17:51 -05:00
Takuma Ueba
6a265aba30 powerpc: mpc85xx: Improve Work-around for Erratum A005125
Work-around for Erratum A005125 must be applied to all cores.

Signed-off-by: Yoshihisa Morizumi <yoshi.morizumi@jp.fujitsu.com>
Signed-off-by: Takuma Ueba <ueba.takuma@jp.fujitsu.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-05-09 09:17:51 -05:00