For the first eMMC read of data for upload, use the "large" dfu_buf (now
configurable) instead of usb request buffer allocated at composite layer
(which is 4KiB) [*].
For eMMC the whole file is read, which usually is larger than the buffer [*]
provided with usb request.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Tom Rini <trini@ti.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
In the following commit:
"dfu: Support larger than memory transfers."
SHA1: ea2453d56b
The ext4{read|write} command formatting has been changed. It removed
a write mandatory [sizebytes] parameter.
It extents DFU_FS_EXT4 case at mmc_file_op to provide mandatory
parameter for DFU write.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Tom Rini <trini@ti.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
The omap_gpio driver is used by AM33XX, OMAP3/4, OMAP54XX and DRA7XX SoCs.
These SoCs have different gpio count but currently omap_gpio driver uses hard
coded 192 which is wrong.
This patch fixes this issue by:
1. Move define of OMAP_MAX_GPIO to all arch/arm/include/asm/arch-omap*/gpio.h.
2. Update gpio bank settings and enable GPIO modules 7 & 8 clocks for OMAP5.
Thanks for Lubomir Popov to provide valuable comments to fix this issue.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Acked-by: Heiko Schocher <hs@denx.de>
During SDRAM_AUTO_DETECTION MA is not configured.
For Soc's > OMAP4460 MA is present. So populating
MA for the same.
Tested on OMAP4430 PANDA, OMAP4460 PANDA.
Reported-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Fix the wrong mapping between the DDR I/O control registers on AM33XX
SoCs and the software representation in the SPL code.
The most recent public TRM defines the following DDR I/O control registers
offsets:
* ddr_cmd0_ioctrl : offset 0x44E11404
* ddr_cmd1_ioctrl : offset 0x44E11408
* ddr_cmd2_ioctrl : offset 0x44E1140C
* ddr_data0_ioctrl: offset 0x44E11440
* ddr_data1_ioctrl: offset 0x44E11444
While the struct ddr_cmdtctrl has also some reserved bits in the beginning.
The struct is mapped to the address 0x44E11404. As a result "cm0ioctl" points
to the ddr_cmd1_ioctrl register, "cm1ioctl" to the ddr_cmd2_ioctrl and etc.
Registers ddr_cmd0_ioctrl and ddr_data0_ioctrl are never configured because
of this mapping mismatch.
Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
This patch fix the omap access to the transceiver
configuration registers using the ulpi bus. As reported by
the documentation the bit31 is used only to check if the
transaction is done or still running and the reading and
writing operation have different offset and have different
values. What we need to do at the end of a transaction is
leave the bus in done state. Anyway an error using the ulpi
omap register is not recoverable so any error give out the
usage of this interface.
Tested on a custom OMAP5430 board with a TUSB1210 ULPI PHY
on USBB1.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Commit 35fc84fa1f broke bootm on avr32. It
requires to call do_bootm_linux() with flag set to BOOTM_STATE_OS_PREP before
calling it again with flag set to BOOTM_STATE_OS_GO.
Fix this by allowing flag set to BOOTM_STATE_OS_PREP, this however will
require a complete refactoring later on.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
[trini: Apply to m68k, microblaze, nds32, nios2, openrisc, sh and sparc]
Signed-off-by: Tom Rini <trini@ti.com>
Remove CONFIG_SPLASH_SCREEN_PREPARE from README
Add doc/README.splashprepare to document functionality
Signed-off-by: Robert Winkler <robert.winkler@boundarydevices.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Create splash.c/h to put the function and any future common splash
screen code in.
Signed-off-by: Robert Winkler <robert.winkler@boundarydevices.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
When compressed image is loaded, it must be decompressed
to an aligned address + 2 to avoid unaligned access exception
on some ARM platforms.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Anatolij Gustschin <agust@denx.de>
CC: Wolfgang Denk <wd@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Some ARM compilers may emit code that makes unaligned accesses when
faced with constructs such as:
const char format[] = "r5g6b5";
Make this data static since it doesn't chagne; the compiler will simply
place it into the .rodata section directly, and avoid any unaligned run-
time initialization.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch change 'data_to_send' array to static to avoid
unaligned access exeption on some platforms (ex Trats2).
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
CC: Anatolij Gustschin <agust@denx.de>
This trivial patch adds the definition of the vid/pid for the Ver C1 of the
USB Ethernet adapter D-Link DUB-E100.
Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
CC: Marek Vasut <marex@denx.de>
while playing with dfu, I tapped in an unaligned access
when doing on the host side a "lsusb -d [vendornr]: -v"
I get on the board:
GADGET DRIVER: usb_dnl_dfu
data abort
MAYBE you should read doc/README.arm-unaligned-accesses
pc : [<8ff71db8>] lr : [<8ff75aec>]
sp : 8ef40d18 ip : 00000005 fp : 00000000
r10: 00000000 r9 : 47401410 r8 : 8ef40f38
r7 : 8ef4aae8 r6 : 0000000a r5 : 8ef4ab28 r4 : 8ef4ab80
r3 : 0000000a r2 : 00000006 r1 : 00000006 r0 : 8ef4aae8
Flags: Nzcv IRQs off FIQs on Mode SVC_32
Resetting CPU ...
reason is that in the "struct usb_composite_dev" the
"struct usb_device_descriptor desc;" is on an odd address,
and this struct gets accessed in
drivers/usb/gadget/composite.c device_qual()
Fix it, by align this var "struct desc" fix to an aligned
address.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
This subtle change fix problem with too small amount of allocated
memory to store DFU function pointers.
One needs to allocate extra space for sentinel NULL pointer in this array
of function pointers.
With the previous code, the NULL value overwrites malloc internal data
and afterwards free(f_dfu->function) crashes.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
add a weak dummy function g_dnl_fixup to add the possibility to update
the device_desc board specific. Used on the upcoming siemens board
support, where idVendor and idProduct is stored in an eeprom.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
- set in to_dfu_mode() f_dfu->dfu_state = DFU_STATE_dfuIDLE
as after every to_dfu_mode call this is done, so move
this into to_dfu_mode
- switch in dfu_bind() into dfu mode:
This fixes wrong "dfu-util -l" output, when calling
"dfu-util -l" after a board reset, without doing a
download before. See also discussion here:
http://lists.denx.de/pipermail/u-boot/2013-June/157272.html
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@ti.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Samuel Egli <samuel.egli@siemens.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
This patch memcpy is used instead of an assignment to
avoid unaligned access execption on some ARM platforms.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
This patch use get|put_unaligned_le16 to access structure data
to avoid data abort on some ARM platforms.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Marek Vasut <marex@denx.de>
Dfu transfer uses a buffer before writing data to the
raw storage device. Make the size (in bytes) of this buffer
configurable through environment variable "dfu_bufsiz".
Defaut value is configurable through CONFIG_SYS_DFU_DATA_BUF_SIZE
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@ti.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Tom Rini <trini@ti.com>
Patch 35fc84fa1 [Refactor the bootm command to reduce code duplication]
breaks booting Linux (compressed uImage with fdt) on powerpc.
boot_jump_linux() mustn't be called before boot_prep_linux() and
boot_body_linux() have been called. So remove the superfluous call
to boot_jump_linux() in arch/powerpc/lib/bootm.c as its called later on
in this function.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@ti.com>
At present mkimage is set up to always build with image signing support.
This means that the SSL libraries (e.g. libssl-dev) are always required.
Adjust things so that mkimage can be built with and without image signing,
controlled by the presence of CONFIG_FIT_SIGNATURE in the board config file.
If CONFIG_FIT_SIGNATURE is not enabled, then mkimage will report a warning
that signing is not supported. If the option is enabled, but libraries are
not available, then a build error similar to this will be shown:
lib/rsa/rsa-sign.c:26:25: fatal error: openssl/rsa.h: No such file or directory
Signed-off-by: Simon Glass <sjg@chromium.org>
This restores the ordering of interrupt disable to what it what before
commit 35fc84fa. It seems that on some archiectures (e.g. PowerPC) the
OS is loaded into an interrupt region, which can cause problems if
interrupts are still running.
Tested-by: Stefan Roese <sr@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
With 35fc84fa1 [Refactor the bootm command to reduce code duplication]
we stopped checking the return value of bootm_load_os (unintentionally!)
and simply returned if we had a non-zero return value from the function.
This broke the valid case of a legacy image file of a single kernel
loaded into an overlapping memory area (the default way of booting
nearly all TI platforms).
The best way to fix this problem in the new code is to make
bootm_load_os be the one to see if we have a problem with this, and if
it's fatal return BOOTM_ERR_RESET and if it's not BOOTM_ERR_OVERLAP, so
that we can avoid calling lmb_reserve() but continue with booting. We
however still need to handle the other BOOTM_ERR values so re-work
do_bootm_states so that we have an error handler at the bottom we can
goto for problems from bootm_load_os, or problems from the other callers
(as the code was before). Add a comment to do_bootm_states noting the
existing restriction on negative return values.
Signed-off-by: Tom Rini <trini@ti.com>
---
Changes in v2:
- Rework so that only bootm_load_os and boot_selected_os head down into
the err case code, and other errors simply return back to the caller.
Fixes 'spl export'.
We've been dropping SoC name from U-Boot prompt as it increase
complexity for automatic testing and makes line longer for no good
reason.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Andy Voltz <andy.voltz@timesys.com>
This adds a default environment which should be able to support both
3.0.15 from Timesys and upcoming 3.11.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Andy Voltz <andy.voltz@timesys.com>
Currently we have the following on boot:
CPU: Freescale i.MX28 rev1.2 at 454 MHz
BOOT: SSP SD/MMC #0, 3V3
DRAM: 128 MiB
MMC: MXS MMC: 0
Video: MXSFB: 'videomode' variable not set!In: serial
Break the line of the warning message in order to have a better reading format.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
enum boot_mode is defined twice once in spl.h and also in
spl_boot.c, hence removing the same from spl_boot.c and including
the header file.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
In a714321 we add a check at the end of findfdt to make sure we have
updated it from undefined and if not, warn the user. This however
forgot a ';' on the end of the previous last test.
Signed-off-by: Tom Rini <trini@ti.com>
SDRAMC_DARCn_BA() macro worked fine when the BA is 0x00000000 even
though the macro is incorrect. It causes the BA to be set incorrctly
for other base addresses. This patch fixes the macro so that base
addresses other than zero can be used with the MCF5235.
Signed-off-by: Steve deRosier <derosier@gmail.com>
There is a debug call in board.c befor serial interface was initialized.
This moves the debug code behind serial_initialize call.
Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Newer gcc versions warn about unused variables. This patch corrects a few of
those warnings that popped up in a build for the palmtreo680 board.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Create a README.mxs file that contains instructions on how to use U-boot for
both MX23 and MX28.
As boot from NAND has only been tested on mx28, make it clear that it only
applies to MX28.
While at it, do some small cleanups for the sake of consistency:
- Use "MX28" instead of "i.MX28"
- Use "section" instead of "chapter" when referring to specific parts of the
reference manual chapters.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
MX28 can boot from SSP0 or SSP1, so it is better not to hardcode the SSP port
in the instructions.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
In order to improve readability keep the text within 80 columns.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
