Finally, found the root cause of the issue already once mentioned back
here [2] which caused the following error message during boot:
imx_wdt watchdog@30280000:
pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19
Turns out while the watchdog node itself was already u-boot,dm-spl its
pinctrl node was not which caused it to be unavailable at that early
stage. Note that any and all other boards I checked also seem to be
missing this. However, I can't judge whether or not they might indeed
need a similar fix or not.
[2] https://marc.info/?l=u-boot&m=161786572422973
Fixes: commit d304e7ace3
("ARM: imx8m: Fix reset in SPL on Toradex iMX8MM Verdin")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This powers some peripherals on the carrier board e.g. the USB hub.
Related-to: ELB-3206
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Prepare for DEK blob encapsulation support through "dek_blob" command.
On ARMv8, u-boot runs in non-secure, thus cannot encapsulate a DEK blob
for encrypted boot.
The DEK blob is encapsulated by OP-TEE through a trusted application
call. U-boot sends and receives the DEK and the DEK blob binaries
through OP-TEE dynamic shared memory.
To enable the DEK blob encapsulation, add to the defconfig:
CONFIG_SECURE_BOOT=y
CONFIG_FAT_WRITE=y
CONFIG_CMD_DEKBLOB=y
Taken from NXP's commit 56d2050f40 ("imx8m: Add DEK blob encapsulation
for imx8m").
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The devicetree submitted and approved for the mainline linux kernel is
slightly different than the one present here. This syncs both
devicetrees (for the Rockchip SFC node at least) present on the PX30
and the Odroid Go Advance. Changes include renaming the flash node,
reordering the values in the SFC node for the rk3326-odroid-go2,
changing the name of the cs pinctrl node to cs0, and updating the
u-boot specific tree to utilize the new flash node value.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Starting with commit 92f1e9a4b3 ("clk: Detect failure to set
defaults") the clk driver for the PX30 would fail to probe for the
Odroid Go Advance. This patch is to remove the clock for the GPU from
the U-Boot specific devicetree, as that clock is not supported by the
U-Boot clk_px30 driver.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command
-----BEGIN PGP SIGNATURE-----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=S4kl
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20211012' of https://source.denx.de/u-boot/custodians/u-boot-stm
- Disable ATAGS for STM32 MCU and MPU boards
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command
Signed-off-by: Tom Rini <trini@konsulko.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmFlfXAcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyHzuB/4pV2iAeFBjNf6YYsuk
uvBQm7+j+AQzy0J337bDwulvw8wTKKlaid4qfOpEjW316DI9oXN1bXTlwNsjtQvO
zTILW7MoBjDRhZHsSkeSfIuD+Sc80juAoLBv+GXskQdZOTQUbWdmi2o60gdY5Ba4
WN0i4zOGVqd7xoDuDgM3XC1M2RnKerxDeVt20Ji+5dFfmes11m7br6sWj2j/45f+
q3G1ufHl+ea+8oRLZGjn2ddKCb1wLLOrNZA+74dsZ5SN0LCN0vFsE3+JAk4RZ2A5
omiHVApjE+J3vAjwiVY7apjcIdVEeyb5AioiXSBAEZiq1l1UI7eKDQT75bDkaKSs
4wBV
=78ME
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.01-b' of https://source.denx.de/u-boot/custodians/u-boot-at91
Second set of u-boot-at91 features for the 2022.01 cycle:
This small feature set adds the support for PWM driver for the sama5d2
SoC. It also adds a node in the DT for this SoC.
The bulk of it is Samuel's DM_I2C rework, which removes the nasty I2C
deprecation warnings for most 32-bit boards. It also includes some
smaller refactorings that pave the way for more changes, mostly driven
by needing to support the Allwinner RISC-V SoC later on.
Board wise we gain support for the FriendlyARM NanoPi R1S H5 router
board and official Pinetab support.
Build-tested for all 160 sunxi boards, and boot tested on a A64, A20,
H3, H6, and H616 board. USB, SD card, eMMC, and Ethernet all work there
(where applicable).
This fixes the usage of the USB 3.0-capable port under U-Boot as USB
2.0-only port.
Original patch by Chao Zeng.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Account for the changes done between merge proposal and the final merge.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Registers for adjusting the spread spectrum clocking (SSC) have been
added. As reported by the TI spruhl7x RM, SSC is supported only for LCD
and MPU PLLs, but the PRCM_CM_SSC_DELTAMSTEP_DPLL_XXX and
PRCM_CM_SSC_MODFREQDIV_DPLL_XXX registers, as well as the enable field
in the PRCM_CM_CLKMODE_DPLL_XXX registers are mapped for all PLLs (CORE,
MPU, DDR, PER, DISP, EXTDEV).
Link: https://lore.kernel.org/r/20210606202253.31649-5-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Registers for adjusting the spread spectrum clocking (SSC) have been
added. As reported by the TI spruh73x RM, SSC is supported only for LCD
and MPU PLLs, but the CM_SSC_DELTAMSTEP_DPLL_XXX and
CM_SSC_MODFREQDIV_DPLL_XXX registers, as well as the enable field in the
CM_CLKMODE_DPLL_XXX registers are mapped for all PLLs (CORE, MPU, DDR,
PER, DISP).
Link: https://lore.kernel.org/r/20210606202253.31649-4-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
This adds support for the NanoPi R1S H5 board.
Allwinner H5 SoC
512MB DDR3 RAM
10/100/1000M Ethernet x 2
RTL8189ETV WiFi 802.11b/g/n
USB 2.0 host port (A)
MicroSD Slot
Reset button
Serial Debug Port
WAN - LAN - SYS LED
The dts file is taken from Linux 5.14 tag.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Current CP1 pinctrl that is set on the Puzzle M801 is incorrect.
CP1 pins are only used for the SMI bus and the MSS I2C, all other
pins are just GPIO-s.
Due to this being set completely wrong, the pinctrl was actually
ended up being hardcoded in the board_early_init_f() step so that
SMI would work.
That is obviously not the right thing to do, so convert the register
hex values that were being written to individual pin modes and set it
in the DTS.
Add the SMI pins to the CP1 MDIO node as otherwise CP1 pinctrl does
not get probed without an consumer.
Fixes: 2ae2b8a2 ("arm: mvebu: Initial iEi Puzzle-M801 support")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Commit 079b35a261 ("arm: a37xx: pci: Increase PCIe MEM size from 16 MiB
to 127 MiB") increased size of PCIe MEM to 127 MiB, which is the maximal
possible size for allocated 128 MiB PCIe window. PCIe IO size in that
commit was unchanged.
Armada 3720 PCIe controller supports 32-bit IO space mapping so it is
possible to assign more than 64 KiB if address space for IO.
Currently controller has assigned 127 MiB + 64 KiB memory and therefore
there is 960 KiB of unused memory. So assign it to IO space by increasing
IO window from 64 KiB to 1 MiB.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 079b35a261 ("arm: a37xx: pci: Increase PCIe MEM size from 16 MiB to 127 MiB")
Reviewed-by: Stefan Roese <sr@denx.de>
Use the common imx8mm-venice-u-boot.dtsi (dtb for the
'DEFAULT_DEVICE_TREE) so that it inherits things like binman.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Use the common imx8mm-venice-u-boot.dtsi (dtb for the
'DEFAULT_DEVICE_TREE) so that it inherits things like binman.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Use the common imx8mm-venice-u-boot.dtsi (dtb for the
'DEFAULT_DEVICE_TREE) so that it inherits things like binman.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The Kontron SoM-Line i.MX8MM (N801x) by Kontron Electronics GmbH is a SoM
module with an i.MX8M-Mini SoC, 1/2/4 GB LPDDR4 RAM, SPI NOR, eMMC and PMIC.
The matching evaluation boards (Board-Line) have 2 Ethernets, USB 2.0, HDMI/LVDS,
SD card, CAN, RS485 and much more.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Remove board_ehci_hcd_init function that is not used with DM_USB
and replace its functionality with device-tree configuraton that treats
USB HUB RST# as a gpio enable for the usbh1 vbus regulator.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
This adds support for i.MX6UL/ULL-based evaluation kits with SoMs by
Kontron Electronics GmbH.
Currently there are the following SoM flavors (SoM-Line):
* N6310: SOM with i.MX6UL-2, 256MB RAM, 256MB SPI NAND
* N6311: SOM with i.MX6UL-2, 512MB RAM, 512MB SPI NAND
* N6411: SOM with i.MX6ULL, 512MB RAM, 512MB SPI NAND
And the according evaluation boards (Board-Line):
* N6310-S: Baseboard with SOM N6310, eMMC, display (optional), ...
* N6311-S: Baseboard with SOM N6311, eMMC, display (optional), ...
* N6411-S: Baseboard with SOM N6411, eMMC, display (optional), ...
Currently U-Boot describes i.MX6UL and i.MX6ULL through separate config
options at compile-time. Though the differences are so minor, that for
the scope of these SoMs we just use a single defconfig that is compatible
with both SoCs.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Synchronize the u-boot and kernel imx device trees, using tuned
script from commit c0157bdcafa1 ("ARM: dts: imx: use generic name bus")
Per devicetree specification, generic names are recommended to be
used, such as bus.
i.MX AIPS is an AHB - IP bridge bus, so we could use bus as node
name.
Script:
sed -i "s/\<aips@/bus@/" arch/arm/dts/imx*.dtsi
sed -i "s/\<aips@/bus@/" arch/arm/dts/vf*.dtsi
sed -i "s/\<aips-bus@/bus@/" arch/arm/dts/imx*.dtsi
sed -i "s/\<aips-bus@/bus@/" arch/arm/dts/vf*.dtsi
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add u-boot.dtsi specific to imx6-apalis with a watchdog enabled.
If OP-TEE is loaded by SPL, it may use a watchdog to handle fails of
u-boot running. Enable the watchdog in SPL to use it by OP-TEE.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Since c6df0e2ffd ("net: phy: micrel: add support for DLL setup on ksz9131")
the Micrel PHY driver correctly configures the delay register. The Verdin PHY
is RGMII-ID, so reflect that in DT, otherwise the ethernet no longer works.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
binman conversion made flashing flash.bin
and u-boot.itb necessary. Update binman config
to create a single flash.bin image again.
This updates imx8mp_evk and phyCORE-i.MX8MP as they share the
same binman config.
Updated also imx8mp_evk documentation.
Tested on phyCORE-i.MX8MP.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Currently imx8mm-cl-iot-gate_defconfig fails to produce a working boot
binary due to the lack of fip.bin:
" BINMAN all
Image 'main-section' is missing external blobs and is non-functional: blob-ext
Some images are invalid"
To make the build process more consistent with the other i.MX8M targets,
split the defconfig in two:
- imx8mm-cl-iot-gate_defconfig: standard defconfig that only
requires ATF / DDR firmware.
- imx8mm-cl-iot-gate-optee_defconfig: "more advanced" defconfig that
requires ATF / Optee / mbedtls / DDR firmware.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
After the enforcement of DM_MMC the microSD card is not detected. Fix by
correctly configuring the card detect in the devicetree.
Signed-off-by: Andrej Rosano <andrej.rosano@f-secure.com>
Import the initial dts queued for Linux 5.16.y
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Alpha sort the Amlogic dtb list (same as the kernel).
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add support for new home automation devices.
JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation controller with the following features:
- DIN Rail Mounting case
- Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 512Mb/1GB DDR3
- 8/16GB eMMC flash
- 1 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac, Bluetooth 4.2.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- 2 x gpio LEDS
- GPIO user Button
- 1 x 1-Wire
- 2 x RS-485
- 4 x dry contact digital GPIO inputs
- 3 x relay GPIO outputs
- DC source with a voltage of 9 to 56 V / Passive POE
JetHome Jethub H1 (http://jethome.ru/jethub-h1) is a home automation controller with the following features:
- Square plastic case
- Amlogic S905W (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 1GB DDR3
- 8/16GB eMMC flash
- 2 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth RTL8822CS IEEE 802.11a/b/g/n/ac, Bluetooth 5.0.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- MicroSD 2.x/3.x/4.x DS/HS cards.
- 1 x gpio LED
- ADC user Button
- DC source 5V microUSB with serial console
Patches from:
- JetHub H1
https://lore.kernel.org/r/20210915085715.1134940-4-adeep@lexina.inhttps://git.kernel.org/amlogic/c/abfaae24ecf3e7f00508b60fa05e2b6789b8f607
- JetHub D1
https://lore.kernel.org/r/20210915085715.1134940-5-adeep@lexina.inhttps://git.kernel.org/amlogic/c/8e279fb2903990cc6296ec56b3b80b2f854b6c79
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: removed unused variable value]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Beelink GS-King X is a variant of the GS King boards but with an internal
USB to SATA bridge and advanced audio features.
[narmstrong: add missing CONFIG_SYS_LOAD_ADDR from defconfig]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Odroid-HC4 is a variant of the Odroid-C4 board but with a PCIe-SATA bridge
instead of the USB3 ports.
[narmstrong: add missing CONFIG_SYS_LOAD_ADDR from defconfig]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Since Linux commmit [1], the order is fixed with aliases, in order to keep the
MMC device order, set it back to HW order in U-Boot dtsi files.
[1] ab547c4fb39f ("arm64: dts: amlogic: Assign a fixed index to mmc devices")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Import Amlogic DT changes from Linux commit 7d2a07b76933 ("Linux 5.14"),
dt-bindings clock changes and new meson-g12b-gsking-x.dts,
meson-sm1-bananapi-m5 & odroid-hc4 boards.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This allows to use the watchdog in custom scripts but does not enforce
that the OS has to support it as well.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Prepares for the addition of the IOT2050 board which is based on the TI
AM65x. The board comes in four variants, Basic and Advanced, each as
product generation 1 (SR1.0) and 2 (SR2.x), so there are separate dts
files needed. Furthermore, the SPL has its own device tree.
Based on original board support by Le Jin, Gao Nian and Chao Zeng.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
The WDT devices described in the general .dtsi file
should be marked as "disabled" by default.
A WDT should be then enabled in the board specific
.dts file on demands.
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
This resyncs the dts files for all of the currently in-tree K3
platforms, along with relevant bindings, with the v5.14 Linux Kernel
release. Of note are that the main-navss/mcu-navss nodes were renamed
to main_navss / mcu_navss and so the u-boot.dtsi files needed to be
updated to match.
Tested on j721e_evm and am65x_evm.
Signed-off-by: Tom Rini <trini@konsulko.com>
zynq:
- Enable capsule update for qspi and mmc
- Update zed DT qspi compatible string
zynqmp:
- Add missing modeboot for EMMC
- Add missing nand DT properties
- List all eeproms for SC on vck190
- Add vck190 SC psu_init
clk:
- Handle only GATE type clock for Versal
watchdog:
- Update versal driver to handle system reset
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYVWWZgAKCRDKSWXLKUoM
IY3MAJ43Mlut5tK9gv45bp4HpyVOMuSvJwCfTiVr7ZxrBE8I8QC5+zHzBTmuM6g=
=aQtT
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.01-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2022.01-rc1
zynq:
- Enable capsule update for qspi and mmc
- Update zed DT qspi compatible string
zynqmp:
- Add missing modeboot for EMMC
- Add missing nand DT properties
- List all eeproms for SC on vck190
- Add vck190 SC psu_init
clk:
- Handle only GATE type clock for Versal
watchdog:
- Update versal driver to handle system reset
