The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
A number of PowerPC platforms define this, for SPL. To move this to
Kconfig, it needs to be CONFIG_SPL_SYS_CCSR_DO_NOT_RELOCATE, so use
CONFIG_IS_ENABLED() to check for usage. A number of layerscape
platforms bring this logic from PowerPC, but only need a small part of
it, for the fman driver. Remove their unused portion at least.
Signed-off-by: Tom Rini <trini@konsulko.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
Rx Compliance tests may fail intermittently at high
jitter frequencies using default register values
Program register USB_PHY_RX_OVRD_IN_HI in certain sequence
to make the Rx compliance test pass.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.bhagat@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
Low Frequency Periodic Singaling (LFPS) Peak-to-Peak Differential
Output Voltage Test Compliance fails using default transmitter settings
Change config of transmitter signal swings by setting register
PCSTXSWINGFULL to 0x47 to pass compliance tests.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
The default setting for USB High Speed Squelch Threshold results
in a threshold close to or lower than 100mV. This leads to Receive
Compliance test failure for a 100mV threshold.
Shift the threshold from ~100mV towards ~130mV by setting SQRXTUNE
to 0x0 to pass USB High Speed Receiver Sensitivity Compliance test.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
USB High Speed (HS) EYE Height Adjustment
USB HS speed eye diagram fails with the default value at
many corners, particularly at a high temperature
Optimal eye at TXREFTUNE value to 0x9 is observed, change
set the same value.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
CoreLink Cache Coherent Interconnect (CCI) provides full cache
coherency between two clusters of multi-core CPUs and I/O coherency
for devices and I/O masters.
This patch add new config option SYS_FSL_HAS_CCI400 and moves
existing register space definaton of CCI-400 bus to fsl_immap to be
shared. CONFIG_SYS_CCI400_ADDR is replaced with SYS_CCI400_OFFSET
in Kconfig.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
[YS: revised commit message, squashed patches for armv8 and armv7]
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds definitions of all the regesters necessary for
system sleep.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
A function is created to detrmine if the boot mode is secure
or non-secure for differnt SoC's.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This is a workaround for hardware erratum.
Write the value of 63b2_0042h to EDDRTQCFG will optimal the
memory controller performance.
The value: 63b2_0042h comes from the hardware team.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Enable the IP feature's snoop signal to support
hardware snoop for cache coherence.
SNPCNFGCR contains the bits to drive snoop signal
for various masters.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch addresses a problem mentioned recently on this mailing list:
[1].
In that posting a LS1021 based system was locking up at about 5 minutes
after boot, but the problem was mysteriously related to the toolchain
used for building u-boot. Debugging the problem reveals a stuck
interrupt 29 on the GIC.
It appears Freescale's LS1021 support in u-boot erroneously sets the
64-bit ARM generic PL1 physical time CompareValue register to all-ones
with a 32-bit value. This causes the timer compare to fire 344 seconds
after u-boot configures it. Depending on how fast u-boot gets the
kernel booted, this amounts to about 5-minutes of Linux uptime before
locking up.
Apparently the bug is masked by some toolchains. Perhaps this is
explained by default compiler options, word sizes, or binutils versions.
At any rate this patch makes the manipulation explicitly 64-bit which
alleviates the issue.
[1]
https://lists.yoctoproject.org/pipermail/meta-freescale/2015-June/014400.html
Signed-off-by: Chris Kilgour <techie@whiterocker.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale ARM-based Layerscape LS102xA contain a SATA controller
which comply with the serial ATA 3.0 specification and the
AHCI 1.3 specification.
This patch adds SATA feature on ls1021aqds and ls1021atwr boards.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Enable snooping for CAAM read & write transactions by
programming the SCFG snoop configuration register:
SCFG_SNPCNFGCR[SECRDSNP]
SCFG_SNPCNFGCR[SECWRSNP]
Signed-off-by: Horia Geantă <horia.geanta@freescale.com>
Reviewed-by: Zhengxiong Jin <Jason.Jin@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Replace the DMACTRL[LE] hack with recommended settings
for ETSECDMAMCR to get the same end effect - obtaining
big-endian buffer descriptors and frame data for eTSEC.
The reset / default value for ETSECDMAMCR is preserved,
excepting the BD and FR bits which are cleared to enable
the BE mode in accordance with the H/W specifications.
Fixes: 52d00a8 "ls102xa: etsec: Add etsec support for LS102xA"
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
Tested-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Move USB controller Base address mapping from ls102xa immap
to fsl xhci header. This is required to remove any warnings when
controller base addresses are mapped for multiple platforms
in their respective files.
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
As SCFG_ENDIANCR register is added to choose little-endian or big-endian
for audio IPs on Rev2.0 silion, little-endian mode is selected.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
ccsr_ddr structure is already defined in fsl_immap.h. Remove
this duplicated define. Move fixed timing into ls1021atwr.h.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Alison Wang <alison.wang@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
For LS102xA, some workarounds are only used in VER1.0, so silicon
version detection are added for QDS and TWR boards.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch is to define default values for some CCSR macros
to make header files cleaner.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
CAAM is connected to CCI-400 S0 slave interface. Disable snooping for
S0 will cause CAAM self test failure. This patch is to enable snooping
for S0 slave interface. These CCI-400 operations are moved to
board_early_init_f() to be initialized earlier. For S4 slave interface,
issuing of snoop requests and DVM message requests are enabled.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch reverts to use ge0_clk125 for eTSEC clock muxing. For SAI and
CAN which are pin multiplexed with RGMII1 in EC1 of RCW, ge2_clk125 will
be used via hwconfig.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Enable hypervisors utilizing the ARMv7 virtualization extension
on the LS1021A-QDS/TWR boards with the A7 core tile, we add the
required configuration variable.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds NAND boot support for LS1021AQDS board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from NAND flash to DDR, finally SPL transfer control to u-boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds QSPI boot support for LS1021AQDS/TWR board.
The QSPI boot image need to be programmed into the QSPI flash
first. Then the booting will start from QSPI memory space.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SCFG_SCFGREVCR is SCFG bit reverse register. This register
must be written with 0xFFFFFFFF before writing to any other
SCFG register. Then other SCFG register could be written in
big-endian mode.
Address: 157_0000h base + 200h offset = 157_0200h
Bit 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15|16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
W/R SCFGREV
Reset 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0-31
SCFGREV SCFG Bit Reverse Control Filed
32'h 0000_0000 - No bit reverse is applied
32'h FFFF_FFFF - Bit reverse is applied; so 31:0 will be stored/read as
0:31
This patch removes the bit reversing for SCFG registers in
u-boot. It will be implemented through PBI commands in RCW
.pbi
write 0x570200, 0xffffffff
.end
So other SCFG register could be written in big-endian mode
in u-boot or kernel directly.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Disable the snoop for slave interface 0, 1 and 2
to avoid the interleaving on the CCI400 BUS.
Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
There are 8 SCFG_SPARECR registers in SCFG memory block, not one.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The QorIQ LS1 family is built on Layerscape architecture,
the industry's first software-aware, core-agnostic networking
architecture to offer unprecedented efficiency and scale.
Freescale LS102xA is a set of SoCs combines two ARM
Cortex-A7 cores that have been optimized for high
reliability and pack the highest level of integration
available for sub-3 W embedded communications processors
with Layerscape architecture and with a comprehensive
enablement model focused on ease of programmability.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
