The read-only-write-enable bit is set by default and must be cleared
to prevent overwriting read-only registers. This should be done
immediately after resetting the PCI Express controller.
Reviewed-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Tony O'Brien <tony.obrien@alliedtelesis.co.nz>
[York S: Move SYS_FSL_ERRATUM_A007815 to Kconfig]
Reviewed-by: York Sun <york.sun@nxp.com>
Core hang occurs when using L1 stashes. Workaround is to disable L1
stashes so software uses L2 cache for stashes instead.
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Darwin Dingel <darwin.dingel@alliedtelesis.co.nz>
Cc: York Sun <york.sun@nxp.com>
[York S: Move SYS_FSL_ERRATUM_A007907 to Kconfig]
Reviewed-by: York Sun <york.sun@nxp.com>
Erratum A-009663 workaround requires to set DDR_INTERVAL[BSTOPRE] to 0
before setting DDR_SDRAM_CFG[MEM_EN] and set DDR_INTERVAL[BSTOPRE]
to the desired value after DDR initialization has completed.
When DDR controller is configured to operate in auto-precharge
mode(DDR_INTERVAL[BSTOPRE]=0), this workaround is not needed.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
move arch/powerpc/include/asm/fsl_errata.h to include/fsl_errata.h
to make it public for both ARM and POWER SoCs.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: fix soc.h path in fsl_errata.h]
Reviewed-by: York Sun <yorksun@freescale.com>
Add a delay of 1 microsecond before issuing soft reset to the
controller to let ongoing ULPI transaction complete.
This prevents corruption of ULPI Function Control Register which
eventually prevents phy clock from entering to low power mode
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
XFI does not work stable on current board, it's due to heat sink issue,
to make it work stable the board needs additional heat sink, enable two
XFI lanes only. Right now we do not have such an erratum for the issue,
so use a define CONFIG_SYS_FSL_B4860QDS_XFI_ERR to identify it.
The workaround will only be used in XFI protocols and only if the
hwconfig indicates that XFI is prefered.
A new VSC3308 config function is used instead of re-use the original
function, to avoid making the function complex and ugly.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T2080 v1.0 has this errata while v1.1 has fixed
this errata by hardware, add a new function has_errata_a007186
to check the SVR_SOC_VER, SVR_MAJ and SVR_MIN first,
if the sil has errata a007186, then run the errata code,
if not, doesn't run the code.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Workaround of Errata A-008044 was implemented without errata number and it is
enabled by default. Errata A-008044 is only valid for T1040 Rev 1.0.
So put errata number and make it conditional.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When device is configured to load RCW from NAND flash IFC_A[16:31] are driven
low after RCW loading. Hence Devices connected on IFC_CS[1:7] and using
IFC_A[16:31] lines are not accessible.
Workaround is already in-place.
Put the errata number to adhere errata handling framework.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Set TXFIFOTHRESH to adjust ddr pipeline delay for successful large
usb writes
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Move USB Errata checking code from "arch/powerpc" to architecture independent
file "fsl_usb.h" so that errata(s) become independent of the architecture.
For each erratum checking function for PPC arch, define a nop function for
non PPC arch for successful compilation in either case
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SerDes PLL is calibrated at reset. When the junction temperature
delta from the time the PLL is calibrated exceeds +56C/-66C,
jitter may increase and can cause PLL to unlock.
This workaround overwrite the SerDes registers with new values,
to calibrate SerDes registers.
These values are known to work fine for all temperature ranges.
This workaround is valid for B4, T4 and T2 platforms, so
added in their config.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <Poonam.Aggrwal@freescale.com>
[York Sun: replaced typedef ccsr_sfp_regs_t with struct ccsr_sfp_regs]
Reviewed-by: York Sun <yorksun@freescale.com>
When the DDR controller is initialized below a junction temperature of
0°C and then operated above a junction temperature of 65°C, the DDR
controller may cause receive data errors, resulting ECC errors and/or
corrupted data. This erratum applies to the following SoCs and their
variants: MPC8536, MPC8569, MPC8572, P1010, P1020, P1021, P1022, P1023,
P2020.
Signed-off-by: York Sun <yorksun@freescale.com>
By default, all PEX inbound windows PEX_PEXIWARn[TRGT] are
mapped to 0xF, which is local memory. But for BSC9132, 0xF
is CCSR, 0x0 is local memory.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Erratum A007212 for DDR is about a runaway condition for DDR PLL
oscilliator. Please refer to erratum document for detail.
For this workaround to work, DDR PLL needs to be disabled in RCW.
However, u-boot needs to know the expected PLL ratio. We put the
ratio in a reserved field RCW[18:23]. U-boot will skip this workaround
if DDR PLL ratio is set, or the reserved field is not set.
Workaround for erratum A007212 applies to selected versions of
B4/T4 SoCs. It is safe to apply the workaround to all versions. It
is helpful for upgrading SoC without changing u-boot. In case DDR
PLL is disabled by RCW (part of the erratum workaround), we need this
u-boot workround to bring up DDR clock.
Signed-off-by: York Sun <yorksun@freescale.com>
Put a delay of 5 millisecond after reset so that ULPI phy
gets enough time to come out of reset. Erratum A007075 applies
to following SOCs and their variants, if any
P1010 rev 1.0
B4860 rev 1.0, 2.0
P4080 rev 2.0, 3.0
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
USB spec says that the minimum disconnect threshold should be
over 525 mV. However, internal USB PHY threshold value is below
this specified value. Due to this some devices disconnect at
run-time. Hence, phy settings are tweaked to increased disconnect
threshold to be above 525mV by using this workaround.
Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SerDes PLLs may not lock reliably at 5 G VCO configuration(A006384)
and at cold temperatures(A006475), workaround recalibrate the
PLLs with some SerDes configuration
Both these errata are only applicable for b4 rev1.
So, make workaround for these errata conditional,
depending upon soc version.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Erratum A006379 says CPCHDBCR0 bit field [10:14] has incorrect default
value after POR. The workaround is to set this field before enabling
CPC to 0x1e.
Erratum A006379 applies to
T4240 rev 1.0
B4860 rev 1.0, 2.0
Signed-off-by: York Sun <yorksun@freescale.com>
In a very rare condition, a system hang is possible when the e500 core
initiates a guarded load to PCI / PCIe /SRIO performs a coherent write
to memory. Please refer to errata document for more details. This erratum
applies to the following SoCs and their variants, if any.
BSC9132
BSC9131
MPC8536
MPC8544
MPC8548
MPC8569
MPC8572
P1010
P1020
P1021
P1022
P1023
P2020
C29x
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
Multiple read/write transactions initiated by security
engine may cause system to hang.
Workaround: set MCFGR[AXIPIPE] to 0 to avoid hang.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
This workaround is for the erratum I2C A004447. Device reference
manual provides a scheme that allows the I2C master controller
to generate nine SCL pulses, which enable an I2C slave device
that held SDA low to release SDA. However, due to this erratum,
this scheme no longer works. In addition, when I2C is used as
a source of the PBL, the state machine is not able to recover.
At the same time, delete the reduplicative definition of SVR_VER
and SVR_REV. The SVR_REV is the low 8 bits rather than the low 16
bits of svr. And we use the CONFIG_SYS_FSL_A004447_SVR_REV macro
instead of hard-code value 0x10, 0x11 and 0x20.
The CONFIG_SYS_FSL_A004447_SVR_REV = 0x00 represents that one
version of platform has this I2C errata. So enable this errata
by IS_SVR_REV(svr, maj, min) function.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
Erratum A-005812 Incorrect reservation clearing in Write Shadow mode can
result in invalid atomic operations. For u-boot, this erratum only impacts
SoCs running in write shadow mode.
Signed-off-by: York Sun <yorksun@freescale.com>
Erratum A-006593 is "Atomic store may report failure but still allow
the store data to be visible".
The workaround is: "Set CoreNet Platform Cache register CPCHDBCR0 bit
21 to 1'b1. This may have a small impact on synthetic write bandwidth
benchmarks but should have a negligible impact on real code."
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
On P204x/P304x/P50x0 Rev1.0, USB transmit will result in false internal
multi-bit ECC errors, which has impact on performance, so software should
disable all ECC reporting from USB1 and USB2.
In formal release document, the errata number should be USB14 instead of USB138.
Signed-off-by: xulei <Lei.Xu@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: xulei <B33228@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When CoreNet Fabric (CCF) internal resources are consumed by the cores,
inbound SRIO messaging traffic through RMan can put the device into a
deadlock condition.
This errata workaround forces internal resources to be reserved for
upstream transactions. This ensures resources exist on the device for
upstream transactions and removes the deadlock condition.
The Workaround is for the T4240 silicon rev 1.0.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Due to SerDes configuration error, if we set the PCI-e controller link width
as x8 in RCW and add a narrower width(such as x4, x2 or x1) PCI-e device to
PCI-e slot, it fails to train down to the PCI-e device's link width. According
to p4080ds errata PCIe-A003, we reset the PCI-e controller link width to x4 in
u-boot. Then it can train down to x2 or x1 width to make the PCI-e link between
RC and EP.
Signed-off-by: Yuanquan Chen <B41889@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The work-around for erratum A-004580 ("Internal tracking loop can falsely
lock causing unrecoverable bit errors") is implemented via the PBI
(pre-boot initialization code, typically attached to the RCW binary).
This is because the work-around is easier to implement in PBI than in
U-Boot itself.
It is still useful, however, for the 'errata' command to tell us whether
the work-around has been applied. For A-004580, we can do this by verifying
that the values in the specific registers that the work-around says to
update.
This change requires access to the SerDes lane sub-structure in
serdes_corenet_t, so we make it a named struct.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The work-around for erratum A-004849 ("CoreNet fabric (CCF) can exhibit a
deadlock under certain traffic patterns causing the system to hang") is
implemented via the PBI (pre-boot initialization code, typically attached
to the RCW binary). This is because the work-around is easier to implement
in PBI than in U-Boot itself.
It is still useful, however, for the 'errata' command to tell us whether
the work-around has been applied. For A-004849, we can do this by verifying
that the values in the specific registers that the work-around says to
update.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
After DDR controller is enabled, it performs a calibration for the
transmit data vs DQS paths. During this calibration, the DDR controller
may make an inaccurate calculation, resulting in a non-optimal tap point.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Boot space translation utilizes the pre-translation address to select
the DDR controller target. However, the post-translation address will be
presented to the selected DDR controller. It is possible that the pre-
translation address selects one DDR controller but the post-translation
address exists in a different DDR controller when using certain DDR
controller interleaving modes. The device may fail to boot under these
circumstances. Note that a DDR MSE error will not be detected since DDR
controller bounds registers are programmed to be the same when configured
for DDR controller interleaving.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Erratum: A-004034
Affects: SRIO
Description: During port initialization, the SRIO port performs
lane synchronization (detecting valid symbols on a lane) and
lane alignment (coordinating multiple lanes to receive valid data
across lanes). Internal errors in lane synchronization and lane
alignment may cause failure to achieve link initialization at
the configured port width.
An SRIO port configured as a 4x port may see one of these scenarios:
1. One or more lanes fails to achieve lane synchronization.
Depending on which lanes fail, this may result in downtraining
from 4x to 1x on lane 0, 4x to 1x on lane R (redundant lane).
2. The link may fail to achieve lane alignment as a 4x, even
though all 4 lanes achieve lane synchronization, and downtrain
to a 1x. An SRIO port configured as a 1x port may fail to complete
port initialization (PnESCSR[PU] never deasserts) because of
scenario 1.
Impact: SRIO port may downtrain to 1x, or may fail to complete
link initialization. Once a port completes link initialization
successfully, it will operate normally.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
P4080 Rev3.0 fixes ESDHC13 errata, so update the code to make the
workaround conditional.
In formal release document, the errata number should be ESDHC13 instead
of ESDHC136.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Erratum A004510 says that under certain load conditions, modified
cache lines can be discarded, causing data corruption.
To work around this, several CCSR and DCSR register updates need to be
made in a careful manner, so that there is no other transaction in
corenet when the update is made.
The update is made from a locked cacheline, with a delay before to flush
any previous activity, and a delay after to flush the CCSR/DCSR update.
We can't use a readback because that would be another corenet
transaction, which is not allowed.
We lock the subsequent cacheline to prevent it from being fetched while
we're executing the previous cacheline. It is filled with nops so that a
branch doesn't cause us to fetch another cacheline.
Ordinarily we are running in a cache-inhibited mapping at this point, so
we temporarily change that. We make it guarded so that we should never
see a speculative load, and we never do an explicit load. Thus, only the
I-cache should ever fill from this mapping, and we flush/unlock it
afterward. Thus we should avoid problems from any potential cache
aliasing between inhibited and non-inhibited mappings.
NOTE that if PAMU is used with this patch, it will need to use a
dedicated LAW as described in the erratum. This is the responsibility
of the OS that sets up PAMU.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This erratum applies to the following SoCs:
P4080 rev 1.0, 2.0, fixed in rev 3.0
P2041 rev 1.0, 1.1, fixed in rev 2.0
P3041 rev 1.0, 1.1, fixed in rev 2.0.
Workaround for erratum NMG_CPU_A011 is enabled by default. This workaround
may degrade performance. P4080 erratum CPU22 shares the same workaround.
So it is always enabled for P4080. For other SoCs, it can be disabled by
hwconfig with syntax:
fsl_cpu_a011:disable
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Erratum NMG_CPU_A011 applies to P4080 rev 1.0, 2.0, fixed in rev 3.0.
It also applies to P3041 rev 1.0, 1.1, P2041 rev 1.0, 1.1. It shares the
same workaround as erratum CPU22. Rearrange registers usage in assembly
code to avoid accidental overwriting.
Signed-off-by: York Sun <yorksun@freescale.com>
We don't care E bit of SVR in most cases. Clear E bit for SVR_SOC_VER().
This will simplify the coding. Use IS_E_PROCESSOR() to identify SoC with
encryption. Remove all _E entries from SVR list and CPU list.
Signed-off-by: York Sun <yorksun@freescale.com>
Erratum A-003474: Internal DDR calibration circuit is not supported
Impact:
Experience shows no significant benefit to device operation with
auto-calibration enabled versus it disabled. To ensure consistent timing
results, Freescale recommends this feature be disabled in future customer
products. There should be no impact to parts that are already operating
in the field.
Workaround:
Prior to setting DDR_SDRAM_CFG[MEM_EN]=1, do the following:
1. Write a value of 0x0000_0015 to the register at offset
CCSRBAR + DDR OFFSET + 0xf30
2. Write a value of 0x2400_0000 to the register at offset
CCSRBAR + DDR OFFSET + 0xf54
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Erratum A-003999: Running Floating Point instructions requires special
initialization.
Impact:
Floating point arithmetic operations may result in an incorrect value.
Workaround:
Perform a read modify write to set bit 7 to a 1 in SPR 977 before
executing any floating point arithmetic operation. This bit can be set
when setting MSR[FP], and can be cleared when clearing MSR[FP].
Alternatively, the bit can be set once at boot time, and never cleared.
There will be no performance degradation due to setting this bit.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Erratum NMG_eTSEC129 (eTSEC86 in MPC8548 document) applies to some early
verion silicons. This workaround detects if the eTSEC Rx logic is properly
initialized, and reinitialize the eTSEC Rx logic.
Signed-off-by: Gong Chen <g.chen@freescale.com>
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The erratum NMG_LBC103 is LBIU3 in MPC8548 errata document.
Any local bus transaction may fail during LBIU resynchronization
process when the clock divider [CLKDIV] is changing. Ensure there
is no transaction on the local bus for at least 100 microseconds
after changing clock divider LCRR[CLKDIV].
Refer to the erratum LBIU3 of mpc8548.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
