Add USB0 OTG support.
Currently, the USB0 OTG nodes are not enabled in the Linux kernel
devicetree.
For this reason, enable the USB0 OTG nodes inside imx8mp-evk-u-boot.dtsi
for now.
Also select several useful options such as USB gadget and fastboot.
Tested by running "ums 0 mmc 2".
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Move the crypto and sec_jr* nodes from board-specific
u-boot.dtsi files into the common files. Additionally protect the
nodes with ifdef CONFIG_FSL_CAAM as they don't serve any purpose if
that is not enabled.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Move the firmware/optee node to the common imx8mp-u-boot.dtsi and
protect it with an ifdef CONFIG_OPTEE as it is a meaningless node
without the optee driver enabled.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The assigned-clock no longer have to be dropped, the clock are now
defined in clk-imx8mp.c and used by DWMAC driver to configure the
DWMAC clock. Drop the workarounds from U-Boot specific DT extras.
Signed-off-by: Marek Vasut <marex@denx.de>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The correct compatible string for i.MX8MP variant of DWC EQoS MAC
is "nxp,imx8mp-dwmac-eqos", use it. Drop the two current users of
the current wrong compatible string to avoid breaking them.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
i.MX8MP EVK has two ethernet ports. Add relevant nodes and properties
for EQoS port to the EVK DTS file.
In -u-boot.dtsi, change the u-boot eqos compatible string, add PHY
reset gpio and remove assigned clocks as not supported in CCF.
Signed-off-by: Ye Li <ye.li@nxp.com>
Factor out the common node settings for dm-spl and dm-pre-reloc
and move them to imx8mp-u-boot.dtsi
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add DEK blob encapsulation support for IMX8M through "dek_blob" command.
On ARMv8, u-boot runs in non-secure, thus cannot encapsulate a DEK blob
for encrypted boot.
The DEK blob is encapsulated by OP-TEE through a trusted application call.
U-boot sends and receives the DEK and the DEK blob binaries through OP-TEE
dynamic shared memory.
To enable the DEK blob encapsulation, add to the defconfig:
CONFIG_SECURE_BOOT=y
CONFIG_FAT_WRITE=y
CONFIG_CMD_DEKBLOB=y
Signed-off-by: Clement Faure <clement.faure@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add phy-reset-duration and phy-reset-post-delay to FEC node for PHY
reset, otherwise the PHY does not work correctly.
Signed-off-by: Ye Li <ye.li@nxp.com>
i.MX8M series provide support for high speed grades in their
usdhc controllers, which has eMMC and SDHC connected to them.
Enable this support across the entire i.MX8M family by providing quirks
to usdhc controllers designated by storage media connected to them.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Some SD Card controller and power circuitry has increased capacitance,
which keeps the internal logic remains powered after regulator is switch
off. This is generally the case when card is switched to SD104 mode,
where a power cycle should be performed. In case if the card internal
logic remains powered, it causes a subsequent failure of mode
transition, effectively leading to failed enumeration.
Introduce a delay of 20 msec in order to provide a possibility for
internal card circuitry to drain voltages and perform a power cycle
correctly.
Similar fix is done in commit c49d0ac38a ("ARM: dts: rmobile: Increase
off-on delay on the SD Vcc regulator") targeted Renesas SOCs.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Stefano Babic <sbabic@denx.de>
Board files should not re-implement do_reset() to work around this
function not being defined in for specific configurations. Rather,
the fix is to compile in drivers which implement this properly.
This patch enables sysreset and watchdog drivers in SPL and ties
them together to implement the same as the do_reset() hack in the
board file, except correctly in the DM/DT framework.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Flavio Suligoi <f.suligoi@asem.it>
Cc: Harald Seiler <hws@denx.de>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
