timer1 is really just the mcu_timer0 node redefined for the WKUP SPL.
Remove the timer1 and replace it with the mcu_timer0 from the Linux
device tree we imported into U-Boot.
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board files unified, we now have a duplicate
wkup_uart0 node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified we now have a
duplicate vtt_supply node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
To make things as organized as possible, start from the Linux board dtbs
and apply all properties needed for U-Boot in our *-u-boot.dtsi file for
the MAIN SPL and U-Boot builds.
We can then include these files for the WKUP SPL build making further
edits to the needed properties and nodes for the WKUP SPL bootloader's
view of the am65x.
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
In order to unify the R5 board dtb file with the Linux board dtb file,
we will need to copy all bootph-pre-ram properties to the *-u-boot.dtsi
overlay.
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Pull in dtb updates for the am654 base board from v6.7-rc1 of Linux
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
The R5 board file for U-Boot should be the same as the board file copied
from Linux with a few alterations to work with the R5's view of the SoC.
First we need to unify the R5 board file and it's U-Boot overlay before
we can unify the Linux board file with this one.
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
- Make DRAM stable on i.MX8MP DHCOM SoM by using FPWM mode and updating
the DRAM timing
- Fix display artifacts when booting Linux on i.MX8M Mini/Plus eDM SBC
The current DDR subsystem configuration occasionally results in write failures,
impacting memory stability, on Verdin AM62 Solo 512MB WB IT 0072 SKU.
This commit addresses the issue by adjusting Drive Pull-Up/Down and
Write Latency to improve the eye diagram and ensure reliable write operations.
This configuration is shared with all Verdin AM62 SoM and
it does not introduce regressions.
Configurations changes from previous / default values:
- Drive Pull-Up/Down from 40 to 34.3 Ohm
- Write Latency from 8 to 10
- ODTLon / ODTLoff latency from 0 / 0 to 4 / 20 nCK
- VREF control range 1 at 27 %
- tFAW from 30 to 40 ns
Configuration is output from SysConfig [1] web tool, currently at version
1.18.1+3343 (DDR SubSystem v9.10).
[1] https://dev.ti.com/sysconfig
Fixes: 7d1a10659f ("board: toradex: add verdin am62 support")
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Turn display connector power off on boot and reboot to prevent any
bogus start up sequence of any panel potentially attached to the
display connector.
Signed-off-by: Marek Vasut <marex@denx.de>
Inhibit DTC warning in imx8mp-dhcom-pdk3-overlay-rev100.dts:
"
arch/arm/dts/imx8mp-dhcom-pdk3-overlay-rev100.dtbo: Warning (reg_format): /fragment@0/__overlay__:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
arch/arm/dts/imx8mp-dhcom-pdk3-overlay-rev100.dtbo: Warning (avoid_default_addr_size): /fragment@0/__overlay__: Relying on default #address-cells value
arch/arm/dts/imx8mp-dhcom-pdk3-overlay-rev100.dtbo: Warning (avoid_default_addr_size): /fragment@0/__overlay__: Relying on default #size-cells value
"
The DTO overwrites the 'reg' property of an ethernet PHY and is only
used on specific combination of old prototype SoM and old prototype
PDK3 carrier board, which had incorrectly placed pull resistor, which
made the PHY change its MDIO address in that specific combination and
which is already fixed on production hardware.
The DTO is implemented in this simple manner because if it contained a
full MDIO bus node reference to define #address-cells and #size-cells,
it would also require a full new copy of the PHY node, i.e.
ethernet-phy@5 { ... reg = <5>; ... }, to avoid DTC warnings about
mismatch between node unit and reg value. The node unit in SoM DT is
ethernet-phy@7 { ... }; .
This simpler approach avoids unnecessary duplication without adverse
side effects.
Reported-by: Fabio Estevam <festevam@denx.de>
Reported-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The aliases and chosen nodes are currently indented using spaces.
Fix them to use the standard tab indentation.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Commit 68dcbdd594 ("ARM: imx: Add weak default reset_cpu()") caused
the 'reset' command in U-Boot to not cause a board reset.
Fix it by switching to the watchdog driver model via sysreset, which
is the preferred method for implementing the watchdog reset
Signed-off-by: Fabio Estevam <festevam@denx.de>
USB host interface is not working on some Apalis Toradex carrier
boards with Apalis iMX8 SoM. This is due to USBH_EN pin, which
powers USB peripherals, having a strong pull-down on some boards,
and a weak pull-down on the others. This USBH_EN pin is left
unconfigured, which means it is in its default state at cold boot:
input with a strong pull-up. As a result, carrier boards with a
weak pull-down have this signal high enough to trigger power
delivery to USB peripherals, and opposite - boards with strong
pull-down on USBH_EN have this signal below the threshold needed
to trigger USB power delivery.
This change configures the USBH_EN pin as gpio hog, fixing this
issue for all Apalis carrier boards regardless of pull-down
resistor value.
Also, update apalis-imx8_defconfig via savedefconfig.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
On branch WIP/17Oct2023, the EEPROM can no longer be read:
U-Boot 2023.10-latest (Oct 17 2023 - 15:53:43 -0400)
CPU: Freescale i.MX8MNano Quad rev1.0 at 1200 MHz
Reset cause: POR
Model: Variscite VAR-SOM-MX8MN Symphony evaluation board
var_read_som_eeprom: uclass_get_device_by_of_offset() failed: -19
initcall failed at call 000000004022207c (err=-19)
Convert EEPROM-related properties to bootph-all so that the EEPROM can
also be read outside of SPL.
Fixes: 9e644284ab ("dm: core: Report bootph-pre-ram/sram node as pre-reloc after relocation")
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The OrangePi Zero 3 is a small development board featuring the Allwinner
H618 SoC, shipping with up to 4GB of DRAM, Gigabit Ethernet, a micro-HDMI
connector and two USB sockets.
The board uses LPDDR4 DRAM and an X-Powers AXP313a PMIC, support for
which was recently added to U-Boot.
Add a defconfig file selecting the right drivers and DRAM options.
Since the .dts file was synced from the Linux kernel repo already, we
just need to add one line to the Makefile to actually build the .dtb.
The DRAM parameters were derived from the values found in the BSP DRAM
drivers on the SPI NOR flash.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mikhail Kalashnikov <iuncuim@gmail.com>
Tested-by: Bob McChesney <bob@electricworry.net>
Tested-by: Stephen Graf <stephen.graf@gmail.com>
The current emac setting is not suitable for Orange Pi Zero 3,
move it back to Orange Pi Zero 2 DT. Also update phy mode and
delay values for emac on Orange Pi Zero 3.
With these changes, Ethernet now looks stable.
Fixes: 95c3b0635e ("sunxi: dts: arm64: update devicetree files from Linux-v6.6-rc6")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
As requirement of CR side, QSPI Flash usage via RPC driver shall
be disabled and leaving the control of this module to CR side.
Perform DT modification to disable the RPC SPI.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Cong Dang <cong.dang.xn@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Do not modify defconfig, modify the DT instead, this way
the RPC SPI can be enabled without recompiling the U-Boot
itself. Update commit message accordingly.]
Use the phandle reference to &rpc node in arch/arm/dts/r8a779g0.dtsi
and remove properties which are already in arch/arm/dts/r8a779g0.dtsi.
No functional change and no resulting DT change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
To quote the author:
Since commit [1], Ethernet is broken on TI AM62 and AM64 platforms.
The commit [1] is not the culprit. It just unearths the problem by fixing
the error check in k3-udma.c. This issue was silently being ignored earlier
due to wrong error check. [NULL instead of FDT_ADDR_T_NONE].
Fix the issue by adding the necessary register spaces for the u-boot K3-UDMA
driver for AM62 and AM64 platforms.
These properties will eventually make it into the SoC DTSi files [2] after
which these can be dropped from k3-*-u-boot.dtsi files.
[1] - 5fecea171de3dd ("treewide: use dev_read_addr_*_ptr() where appropriate")
[2] - https://lore.kernel.org/linux-arm-kernel/20230810174356.3322583-1-vigneshr@ti.com/
Update main_bcdma and main_pktdma nodes for native configuration in the
absence of DM services.
Drop duplicate main_pktdma node in k3-am642-sk-u-boot.dtsi.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Update main_bcdma and main_pktdma nodes for native configuration in the
absence of DM services.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
_ Fix compilation issue when SYS_DCACHE_OFF and/or SYS_DCACHE_SYS are enabled
_ Fix issue following DT sync with kernel 6.3 for stm32mp15xx-ev1 and DHSOM SoM
_ Enable TCP, IPv6, wget on DH STM32MP15 DHSOM
_ Limit u-boot.itb size to 0x160000 bytes on DH STM32MP15 DHSOM
_ Read auth stats and boot_partition from tamp
- Fix some issues Coverity has reported, update MAINTAINERS file,
another bootstd fix, typo fix in error message, gitignore fix and
update TI's URL in many places.
Provide configuration to read cpuid and generate a persistent
MAC address in ethaddr
Signed-off-by: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
RV1126 fails to boot on 2024.01-rc1.
Commit 9e644284ab ("dm: core: Report bootph-pre-ram/sram node as
pre-reloc after relocation") changed the behaviour of bootph-pre-ram, to
limit nodes to spl phase. This caused rv1126 boards to fail to boot with
the current dts.
This patch updates the pmu/grf nodes to bootph-all tags as they are
needed in all phases. This fixes the boot issue on rv1126 boards.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The patch fixed by this commit renders ST STM32MP15xx EV1 board and
all DHSOM SoM based boards unbootable from SPI NOR. Fix the damage
by updating -u-boot.dtsi to match the stm32mp15-pinctrl.dtsi update.
Fixes: 08002ffd08 ("ARM: dts: stm32mp: alignment with v6.3")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
QuartzPro64 is a Rockchip RK3588 based SBC by Pine64.
UART and boot over SD/eMMC/RJ45 are tested to work.
Linux commits from next-20231013:
8152d3d070a9 ("arm64: dts: rockchip: Add QuartzPro64 SBC device tree")
Signed-off-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Cc: Eugen Hristev <eugen.hristev@collabora.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Ondrej Jirman <megi@xff.cz>
Xilinx is using standard mtd partition layout for quite a long time. It is
used for testing purpose on evaluation boards.
Also #address/size-cells shouldn't be present without nodes which should
use them that's why move them from zynq-7000.dtsi to nand/nor nodes
directly.
The patch was tested on zc706 and zedboard(with also increasing max
frequency and rx bus width).
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/4c3348981bba32d3892194420d78fe8621c47534.1698837725.git.michal.simek@amd.com
SMMU is disabled by default and not all masters can be enabled at the same
time because of limited number of entries. That's why comment all iommu
properties but keep them for reference in DT. In XEN case they should be
added back and Xen should have SMMU enabled by default.
Also add IDs for DP and DPDMA.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/e868c27c52ded5d8ef25f75ba394b1ab3b31b80a.1698825657.git.michal.simek@amd.com
Mini U-Boot is running out of OCM and it's only purpose is to program non
volatile memories. There are different configurations which ospi/qspi can
be that's why describe them via DT.
DT binding is already approved that's why there is no reason not to add it.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/a99a8d72201a782fc811715942dea97fb5ab583b.1698329087.git.michal.simek@amd.com
Mini U-Boot is running out of OCM and it's only purpose is to program non
volatile memories. There are different configurations which ospi/qspi can
be that's why describe them via DT.
DT binding is already approved that's why there is no reason not to add it.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/9518ab1c4299a45e800b8611172edd78c9243132.1698329087.git.michal.simek@amd.com
Mini U-Boot is running out of OCM and it's only purpose is to program non
volatile memories. There are different configurations which qspi can be
that's why describe them via DT.
DT binding is already approved that's why there is no reason not to add it.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/e7d31a9d9c4a76e171eefc619f31fabd0831a614.1698329087.git.michal.simek@amd.com
Mini U-Boot is running out of OCM and it's only purpose is to program non
volatile memories. There are different configurations which qspi can be
that's why describe them via DT.
DT binding is already approved that's why there is no reason not to add it.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/28b3cdd7e91b2b4c3c36d0bf65aa5bac042f248c.1698329087.git.michal.simek@amd.com
gpio38 is used in SOM's kv260 to reset the Ethernet PHY.
At present, HW reset is not working properly as Tri-state
is enabled for MIO38, causing inappropriate PHY register reads.
Disabled Tri-state for MIO38 to make HW reset work.
Tri-state disable :
ZynqMP> md 0xFF180208 2
ff180208: 00bfe7a3 00000540
Tri-state enable :
ZynqMP> md 0xFF180208 2
ff180208: 00bfe7e3 00000540
Signed-off-by: Tejas Bhumkar <tejas.arvind.bhumkar@amd.com>
Link: https://lore.kernel.org/r/20231020050622.972750-1-tejas.arvind.bhumkar@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
