Commit graph

34 commits

Author SHA1 Message Date
Fabio Estevam
c27c07b86b ARM: mx28: Remove CONFIG_ARCH_CPU_INIT
No need to define CONFIG_ARCH_CPU_INIT.

All mx28 based boards should use arch_cpu_init().

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
2012-07-07 14:07:44 +02:00
Marek Vasut
e3ddc64603 i.MX28: Add function to adjust memory parameters
This function can be overridden at run-time and allows implementors
of new boards based on the i.MX28 chip to fine-tune the memory params.
It is possible to write into the dram_vals array because when the SPL
runs, it is located SRAM. Therefore the location is writable. There is
no possibility of these data to be read-only.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
2012-07-07 14:07:29 +02:00
Marek Vasut
39007ec8cd i.MX28: Avoid redefining serial_put[cs]()
Do not define serial_putc() and serial_puts() calls if
CONFIG_SPL_SERIAL_SUPPORT is set.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-05-15 08:31:36 +02:00
Marek Vasut
7dec1bd11f i.MX28: Add battery boot components to SPL
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
2012-05-15 08:31:36 +02:00
Marek Vasut
399d9dab3d i.MX28: Reorder battery status functions in SPL
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
2012-05-15 08:31:36 +02:00
Marek Vasut
3f3255c3d7 i.MX28: Add LRADC init to i.MX28 SPL
This code is part of battery boot support for i.MX28.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
2012-05-15 08:31:36 +02:00
Marek Vasut
8d4c759f2c i.MX28: Shut down the LCD controller before reset
If the LCD controller is on before the CPU goes into reset, the traffic on LCDIF
data pins interferes with the BootROM's boot mode sampling. So shut the
controller down.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
2012-05-15 08:31:36 +02:00
Marek Vasut
f8c4a86b5e i.MX28: Implement boot pads sampling and reporting
This patch implements code that samples i.MX28 boot pads and reports boot mode
accordingly.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
2012-05-15 08:31:35 +02:00
Marek Vasut
0239c2fb4a i.MX28: Improve passing of data from SPL to U-Boot
Pass memory size from SPL via structure located in SRAM instead of SCRATCH
registers. This allows passing more data about boot from SPL to U-Boot, like the
boot mode pads configuration.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
2012-05-15 08:31:35 +02:00
Marek Vasut
8f975865be i.MX28: Add delay after CPU bypass is cleared
This solves issues when larger amount of DRAM is used, like 256MB.
Behave the same in case of CPU bypass as we do in case of EMI
bypass, but wait 15 ms. We need to wait until the clock domain
stabilizes.

This issue seemed to have been caused by not waiting after frobbing
with the CPU bypass, it was unrelated to memory, but had a direct
impact, causing trouble. This was yet another X-File of the
imx-bootlets, sigh. The conclusion is, trying a semi-random delay
(there is delay after the EMI bypass change), the issue is fixed.

Another possible explanation is that we do not do the "simple memory
test" FSL does in their imx-bootlets (1000 R/W cycles to/from piece of
the memory, while also outputing something on the serial port). This
might have caused the similar delay in the imx-bootlets and therefore
they didn't need to add this explicitly.

For now, this seems good fix enough, but to me, whole that memory
init code in imx-bootlets is completely flunked and it'd need deeper
investigation.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
2012-05-15 08:31:35 +02:00
Marek Vasut
d2f7ae14d3 Revert "i.MX28: Enable additional DRAM address bits"
This reverts commit 69d26d09de.

Apparently, this commit got mainline only because of out-of-tree
port and causes breakage on board that is mainline. Revert.

Reason:
* The OOT board has 512MB of DRAM, enabling this additional address
  line enabled it to work fine with 512MB of RAM.
* Every mainline port has max. 256MB of DRAM, therefore this revert
  has no impact on any mainline port
* Though this caused a problem with new M28 board with 256MB of DRAM
  where the chips are wired differently. The patch-to-be-reverted
  caused the DRAM to behave like this:

  [128MB chunk #1][128MB chunk #1 again][128MB chunk #2][128MB chunk #2 again]

Therefore to retain the current one-memory-init-rules-them-all situation,
revert this patch until another board emerges and will actually be pushed
mainline that needs different setup.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
2012-05-15 08:31:32 +02:00
Marek Vasut
96666a39ae DMA: Split the APBH DMA init into block and channel init
This fixes the issue where mxs_dma_init() was called either twice or never,
without introducing any new init hooks.

The idea is to allow each and every device using the APBH DMA block to
configure and request only the channels it uses, instead of making it call init
for all the channels as is now.

The common DMA block init part, which only configures the block, is then called
from CPUs arch_cpu_init() call.

NOTE: This patch depends on:

	http://patchwork.ozlabs.org/patch/150957/

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-04-16 14:53:59 +02:00
Marek Vasut
345cd3584c i.MX28: Enable caches by default
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2012-03-29 07:57:08 +02:00
Marek Vasut
494931a674 i.MX28: Drop __naked function from spl_mem_init
Instead of compiling the function and using the result as a constant, simply use
the constant.

NOTE: This patch works around bug:

  http://gcc.gnu.org/bugzilla/show_bug.cgi?id=52546

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
2012-03-27 09:41:16 +02:00
Marek Vasut
a89300338a i.MX28: Make the stabilization delays shorter
Cut down the VDDIO/VDDA regulator stabilization delays to 500 uS. That should be
enough according to the datasheet and bootlets.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Robert Deliën <robert@delien.nl>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
2012-03-27 09:41:16 +02:00
Marek Vasut
69d26d09de i.MX28: Enable additional DRAM address bits
Enables all fourteen address lines for DRAM

Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Marek Vasut <marek.vasut@gmail.com>
2012-03-27 09:41:15 +02:00
Robert Delien
56df16f25a Fix erroneous 32-bit access to hw_clkctrl_frac0 and hw_clkctrl_frac1 registers
This patch fixes erroneous 32-bit access to registers
hw_clkctrl_frac0 and hw_clkctrl_frac1.

Signed-off-by: Robert Delien <robert@delien.nl>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
2012-03-26 23:09:24 +02:00
Robert Delien
b228e14e96 Renamed mx28_register to mx28_register_32 to prepare for mx28_register_8
This patch renames mx28_register to mx28_register_32 in order to
prepare for the introduction of an 8-bit register, mx28_register_8.

Signed-off-by: Robert Delien <robert@delien.nl>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
2012-03-26 23:09:24 +02:00
Marek Vasut
40083c52f7 i.MX28: Reformat the DRAM memory configuration data
Reformat the data so it's easier to navigate through them.

Signed-off-by: Marek Vasut <marex@denx.de>
2012-03-26 23:09:24 +02:00
Robert Delien
1e94d07faf i.mx28: Replaced magic numbers for scratch register addresses with register definitions
This patch replaces the use of magice numbers for scratch register
addresses with earlier defined register definitions.

Signed-off-by: Robert Delien <robert@delien.nl>
2012-03-26 23:09:23 +02:00
Marek Vasut
ff250f3ed8 MX28: Fix get_timer() / get_tbclk() issue
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
2012-02-27 21:19:23 +01:00
Matthias Fuchs
61698fd563 mx28: fix SPL code to make USB booting work
This patch fixes booting i.MX28 CPUs via USB download.
In this mode the CPU's bootrom implements a USB HID device that
accepts a bootstream.

When downloading the bootstream via USB, first the SPL code is
received and executed. Then the u-boot image is received and
called.

The USB bootmode is interrupt driven.

This patch fixes two things:

1) The ARM's fast interrupt mode is disabled when the SPL code
has been run. So save and restore the CPSR register.

2) Save and restore c1 control register: the exception vector
location needs to be set back to bootrom space to make the USB
interrupts work again. The SPL code needs to change this
option for the ram size probing.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
2012-02-27 21:19:23 +01:00
Marek Vasut
534dbd1219 i.MX28: Fix VDDIO and VDDA setup
The DC power STS shouldn't be checked if booting off 5V supply.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Robert Deliën <robert@delien.nl>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
2012-02-27 21:19:23 +01:00
Fabio Estevam
82182720e7 mx28: Show CPU frequency
Showing CPU frequency during boot is useful information.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-02-12 10:11:26 +01:00
Zach Sadecki
8db9eff6c5 mx28: fix clearing of IRQs in power init
There are 2 locations in the power init code for the mx28 where IRQs are not being cleared because incorrect methods to clear those bits were being used.  This was causing my board to get stuck waiting for POWER_CTRL_VDD5V_DROOP_IRQ to clear.  Using the correct method to clear the IRQs fixes it.

Signed-off-by: Zach Sadecki <zach@itwatchdogs.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
2012-01-16 08:40:10 +01:00
Fabio Estevam
5bcc6a8901 mx28: Let dram_init be common for mx28
Let dram_init function be a common function, so that other mx28 boards
can reuse it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
2012-01-16 08:40:09 +01:00
Fabio Estevam
5cb525f3d2 mx28: Let imx_get_mac_from_fuse be common for mx28
Let imx_get_mac_from_fuse function be a common function, so that other
mx28 boards can reuse it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-01-16 08:40:09 +01:00
Veli-Pekka Peltola
00699f847d mx28: remove omap specific config options
Config options for OMAP are not used with i.MX28 so remove dead code.

Signed-off-by: Veli-Pekka Peltola <veli-pekka.peltola@bluegiga.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-01-16 08:40:08 +01:00
Marek Vasut
8ba1604d34 M28: Cleanup memsize.o OOT build
The current way memsize.c is built just made a symlink into the directory
with SPL and then compiled it like any other file there. This was bad as that
broke the out-of-tree build.

The new way introduced in this patch uses the standard spl/Makefile methods
(CONFIG_SPL_LIBCOMMON_SUPPORT / CONFIG_SPL_LIBGENERIC_SUPPORT) to let files in
common/ be built. Because common/Makefile says memsize.c is always built (SPL
and non-SPL build), this fixes our issue with memsize.c out-of-tree build.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2011-12-09 17:30:10 +01:00
Marek Vasut
c944a3ef82 i.MX28: Move SPL to arch/arm/cpu/arm926ejs/mx28
This moves SPL to common location so it can be reused by multiple boards. Also,
this commit adjusts M28 SoM to avoid breakage due to the move.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2011-12-09 17:30:10 +01:00
Marek Vasut
22fe68fbdc iMX28: Fix ARM vector handling
This patch introduces proper ARM vector handling for i.MX28 CPU. This issue
wasn't addressed because the interrupts weren't enabled on any ARMv5 core,
therefore the issue wasn't noticed earlier.

In previous implementation, the vectoring code used by i.MX28 CPU when an
exception happened was that of the SPL. With this change, the branch target when
an exception happens can be reconfigured by U-Boot.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
2011-11-11 11:36:58 +01:00
Marek Vasut
6b6440def8 iMX28: Add GPIO control
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
2011-11-11 11:36:57 +01:00
Marek Vasut
d91a672b6d iMX28: Add PINMUX control
Taken from Linux kernel with minor modifications:

commit bf985969e27b507f734435a99df8bf745a3dbb2b
Author: Shawn Guo <shawn.guo@freescale.com>
Date:   Mon Dec 20 22:57:43 2010 +0800

    ARM: mxs: Add iomux support

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
2011-11-11 11:36:57 +01:00
Marek Vasut
6e9a0a3967 iMX28: Initial support for iMX28 CPU
This patch supports:
- Timers
- Debug UART
- Clock

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
2011-11-11 11:36:56 +01:00