Adding the register definitions for omap3 DMA controller to cpu.h
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Adding the base register address of OMAP3 DMA controller.
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
All ddr configurations(geometry/timings) are done automatically
by detecting the device connected at run time. Though this
is a useful feature, making this as a default setting increases
the code size by about 2K bytes. This is quite big, especially
in the case of SPL which runs from a smaller SRAM. So do not
use this feature as the default setting, instead use the
precalculated tables.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
MDSTAT.STATE occupies bits 0..5 according to all available documentation, so fix
the mask which previously was leaving out the intermediate state indicator bit.
While at it, introduce two #define's for that mask -- unfortunately, we can't
use a single #define as the assembly code can't include <asm/arch/hardware.h>
due to C-specfic constructs in it.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Not all padconfs are the same between 4430 and 4460, so instead of
working around this with an if, we should have an specific padconf
structure for both chips (like handling the differences between the LEDs
GPIOs and TPS).
Signed-off-by: Ricardo Salveti de Araujo <ricardo.salveti@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
OMAP4460 has a different set of values for the ID code, so moving the
old ones to be related just with 4430.
Signed-off-by: Ricardo Salveti de Araujo <ricardo.salveti@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
For files like the drivers/serial/serial.c, it must include the
platform file, as the CONFIG_SYS_NS16550_COM1 must reference to
the definition in the platform definition files.
Include the platform definition file in the config file, so that it
would decouple the dependence for the driver files.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Build pass with following config:
dkb_config
aspenite_config
edminiv2_config
openrd_ultimate_config
sheevaplug_config
mv88f6281gtw_ge_config
rd6281a_config
guruplug_config
km_kirkwood_config
Signed-off-by: Lei Wen <leiwen@marvell.com>
Acked-by: Wolfgang Denk <wd@denx.de>
For files like the drivers/serial/serial.c, it must include the
platform file, as the CONFIG_SYS_NS16550_COM1 must reference to the
definition in the platform definition files.
Include the platform definition file in the config file, so that it
would decouple the dependence for the driver files.
Signed-off-by: Lei Wen <leiwen@marvell.com>
For files like the drivers/serial/serial.c, it must include the
platform file, as the CONFIG_SYS_NS16550_COM1 must reference to the
definition in the platform definition files.
Include the platform definition file in the config file, so that it
would decouple the dependence for the driver files.
Updated cpu.h to remove build errors for gplugd board (by prafulla)
Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
For files like the drivers/serial/serial.c, it must include the platform
file, as the CONFIG_SYS_NS16550_COM1 must reference to the definition in
the platform definition files.
Include the platform definition file in the config file, so that it
would decouple the dependence for the driver files.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Copied wholeheartedly from board/Marvell/guruplug and modified to add support
for SPI NOR flash.
CONFIG_MACH_DREAMPLUG defined in include/configs/dreamplug.h until Linus's
kernel.org tree adds it to mach-types.h. Once it trickles down, the definition
can be removed from include/configs/dreamplug.h.
Signed-off-by: Jason Cooper <u-boot@lakedaemon.net>
Fix checkpatch warning and errors in several i.MX related files.
While at it also address a checkpatch warning at arch/arm/cpu/armv7/mx5/soc.c
regarding the usage of extern in a C file.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Switch to new pmic generic driver.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Jason Liu <jason.hui@linaro.org>
Acked-by: Jason Liu <jason.hui@linaro.org>
Instead of using directly the i2c_set_bus() function,
the I2C_SET_BUS macro must be used to avoid build
errors for targets without multibus I2C.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Switch to new pmic generic driver.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Enable support for new PMIC driver at GONI reference target.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
This commit adds support for MAX8998 PMIC driver.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
I2C or SPI PMIC devices can be accessed.
Separate files: pmic_i2c.c and pmic_spi.c are responsible
for handling transmission over I2C or SPI bus.
New flags:
CONFIG_PMIC - enable PMIC general device.
CONFIG_PMIC_I2C/SPI - specify the interface to be used.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Currently there are two config options for building a U-boot binary for MX31PDK:
make mx31pdk_config
or,
make mx31pdk_nand_config
mx31pdk_config was developed first when no NAND SPL support was available for
MX31 and it requires that the U-boot binary is loaded into RAM via JTAG and it
forces SKIP_LOWLEVEL_INIT.
mx31pdk_nand_config was added later and it allows booting from NAND Flash.
Leave just one config option called mx31pdk so that it produces a binary that can boot from NAND Flash.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
setup_weimcs() and some macros are added to support the setup
for i.MX31 WEIM chip selects. As a compromise between verbosity
and readability an ASCII-art'ish bit comment is used instead of
bitfields.
All i.MX31 boards have been patched to use this approach using a
helper program to verify the changes.
Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
Acked-by: Stefano Babic <sbabic@denx.de>
This commit updates the mach-types based on the latest in Linus's head
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
This function is also defined in omap-common/spl_mmc.de so the implementation
in devkit8000.c was protected by a ifdef.
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
This adds the required GPIO and pinmux configuration to make eMMC / SD work
on Seaboard.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Warren <twarren@nvidia.com>
