This adds a dev argument to some functions so dev_xxx always has a device
to log with. In one instance we must use use a different log function when
we are compiled without DM_USB.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX2x4MgAKCRDKSWXLKUoM
IZQtAJ9HpNwG5q3nHt9WedzLCTkr3YoLAACeJJ0Wlpp5p5xPzuPmnoo/Vi4MtNQ=
=yxRo
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.01' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.01
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
Zynq/ZynqMP/Versal IPs should be possible to called also from Microblaze in
PL and vice versa. That's why change dependencies and do not limit enabling
just for some platforms.
This is follow up patch based on commit 664e16ce99 ("xilinx: kconfig:
Change Kconfig dependencies for Xilinx drivers").
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
As the error message is now displayed by generic phy functions,
the pr_err can be change to pr_debug.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
As the error message is now displayed by generic phy functions,
the dev_err can be change to dev_dbg.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
When unregister gadget driver in ci_udc, the usb device is not
removed or stop. This causes next "usb start" fails to work.
Add a new interface "usb_remove_ehci_gadget" in usb-uclass to
remove the usb device for DM driver. Using "usb_lowlevel_stop" for
non-DM driver.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To help this tedious work, this commit converts devfdt_get_addr_ptr()
to dev_read_addr_ptr() by coccinelle. I also removed redundant casts
because dev_read_addr_ptr() returns an opaque pointer.
To generate this commit, I ran the following semantic patch
excluding include/dm/.
<smpl>
@@
type T;
expression dev;
@@
-(T *)devfdt_get_addr_ptr(dev)
+dev_read_addr_ptr(dev)
@@
expression dev;
@@
-devfdt_get_addr_ptr(dev)
+dev_read_addr_ptr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
node varaible is used as iterator into ofnode_for_each_subnode()
loop, when exiting of it, node is no more a valid ofnode.
Use dwc3_node instead as parameter of ofnode_valid()
Fixes: ac28e59a57 ("usb: Migrate to support live DT for some driver")
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Some platforms, like MIPS Octeon, use mapped addresses (virtual address
!= physical address). On these platforms we need to make sure, that the
local virtual addresses are converted to physical (DMA) addresses for
the xHCI controller. This patch adds the missing virt_to_phys() calls,
so that the correct addresses are used.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
These values are already swapped to CPU endianess, so swapping them
again is a bug. Let's remove the swap here instead.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
xhci_writeq() makes the CPU->LE swapping only when addressing registers
in the xHCI controller address range and not in the local memory (RAM).
We need to use cpu_to_le64() here to ensure that the conversion is done
correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
While trying to use the U-Boot xHCI driver on the MIPS Octeon platform,
which is big endian, I noticed that the driver is missing a few endian
conversion calls. This patch adds these missing endian conversion
calls.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Use the _ptr suffixed variant instead of casting. Also, convert it to
dev_read_addr_ptr(), which is safe to CONFIG_OF_LIVE.
One curious part is an error check like follows in
drivers/watchdog/omap_wdt.c:
priv->regs = (struct wd_timer *)devfdt_get_addr(dev);
if (!priv->regs)
return -EINVAL;
devfdt_get_addr() returns FDT_ADDR_T_NONE (i.e. -1) on error.
So, this code does not catch any error in DT parsing.
dev_read_addr_ptr() returns NULL on error, so this error check
will work.
I generated this commit by the following command:
$ find . -name .git -prune -o -name '*.[ch]' -type f -print | \
xargs sed -i -e 's/([^*)]*\*)devfdt_get_addr(/dev_read_addr_ptr(/'
I manually fixed drivers/usb/host/ehci-mx6.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Use the _ptr suffixed variant instead of casting. Also, convert it to
dev_read_addr_ptr(), which is safe to CONFIG_OF_LIVE.
One curious part is an error check like follows in
drivers/watchdog/omap_wdt.c:
priv->regs = (struct wd_timer *)devfdt_get_addr(dev);
if (!priv->regs)
return -EINVAL;
devfdt_get_addr() returns FDT_ADDR_T_NONE (i.e. -1) on error.
So, this code does not catch any error in DT parsing.
dev_read_addr_ptr() returns NULL on error, so this error check
will work.
I generated this commit by the following command:
$ find . -name .git -prune -o -name '*.[ch]' -type f -print | \
xargs sed -i -e 's/([^*)]*\*)devfdt_get_addr(/dev_read_addr_ptr(/'
I manually fixed drivers/usb/host/ehci-mx6.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Some atypical users of xhci might need to manually reset their xHCI
controller before starting the HCD setup. Check if a reset controller
device is available to the PCI bus and trigger a reset.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
[mb: squash fix to only build xhci_reset_hw() if CONFIG_DM_BUS]
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
In current code there is no cache flush after initializing the scratchpad
buffer array with the scratchpad buffer pointers. This leads to a failure
of the "slot enable" command on the rpi4 board (Broadcom STB PCIe
controller + VL805 USB hub) - the very first TRB transfer on the command
ring fails and there is a timeout while waiting for the command completion
event. After adding the missing cache flush everything seems to be working
as expected.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
It is possible to specify a device tree node for an USB device. This is
useful if you have a static USB setup and want to use aliases which
point to these nodes, like on the Raspberry Pi.
The nodes are matched against their hub port number, the compatible
strings are not matched for now.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is defined in the asm/cache.h header file. Update this header file to
include it so it gets the same value consistently across U-Boot.
This fixes 'usb host' on omapl138_lcdk.
Fixes: 90526e9fba ("common: Drop net.h from common header")
Reported-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
- Fix mmc of path after syncfrom kernel dts;
- Add dwc3 host support with DM for rk3399;
- Add usb2phy and typec phy for rockchip platform;
- Migrate board list doc to rockchip.rst;
- Add rk3399 Pinebook Pro board support;
- Update dram_init in board_init and add memory node in SPL;
We have changed to use dwc3 generic driver for usb3.0 host, so the
legacy Rockchip's xHCI driver is not needed, and drop it.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Print the error code if the regulator enable fails, otherwise the error
message is rather useless and confusing.
Signed-off-by: Marek Vasut <marex@denx.de>
The regulator-fixed would return -ENOSYS when enabled/disabled,
because this operation is not supported, but this is not an error
e.g. on systems where the VBUS cannot be controlled, so if this
is the error code reported by the regulator core, consider it a
success and continue.
Signed-off-by: Marek Vasut <marex@denx.de>
The phy_bulk pointer *usb_phys is used before allocated,
fix it by using a phy_bulk variable instead in
xhci_dwc3_platdata struct
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
The omap3.dtsi file shows the usbhshost node with two sub-nodes
for ohci and ehci. This patch file creates the usbhshost, and
pulls the portX-mode information. It then locates the EHCI
sub-node, and initializes the EHCI controller with the info
pulled from the usbhshost node.
There is still more to do since there isn't an actual link
between the 'phys' reference and the corresponding phy driver,
and there is no nop-xceiv driver yet.
In the meantime, the older style reference to
CONFIG_OMAP_EHCI_PHYx_RESET_GPIO is still needed to pull
the phy out of reset until the phy driver is completed and the
phandle reference is made.
Signed-off-by: Adam Ford <aford173@gmail.com>
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
Have this symbol follow the pattern of all other such symbols.
This patch also removes a TODO from the code.
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Have this symbol follow the pattern of all other such symbols.
This patch removes a TODO from the code.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Add fuse check for USB. If the fuse indicates the module
will not work in the SoC, let's fail the initialization.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This patch is used to support the on-chip xHCI controller on
MediaTek SoCs, currently control/bulk/interrupt transfers are
supported.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Get a group of phys by the phy bulk API
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
dwc3-sti-glue has been broken since MISC uclass has been
modified to scan DT sub-nodes after bind.
Fixing it by a using the no-op uclass.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Solve issue for the display of "usb start" command on stm32mp1
because one carriage return is missing in DWC2 probe.
Before the patch:
STM32MP> usb start
starting USB...
Bus usb-otg@49000000: Bus usbh-ehci@5800d000: USB EHCI 1.00
after the patch:
STM32MP> usb start
starting USB...
Bus usb-otg@49000000: USB DWC2
Bus usbh-ehci@5800d000: USB EHCI 1.00
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Assert reset before deassert in dwc2_reset;
this patch solve issues when the DWC2 registers are already
initialized with value incompatible with host mode.
Force a hardware reset of the IP reset all the DWC2 registers at
default value, the host driver start with a clean state
(Core Soft reset doen in dwc_otg_core_reset is not enought
to reset all register).
The error can occurs in U-Boot when DWC2 device gadget driver
force device mode (called by ums or dfu command, before to execute
the usb start command).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add support for clock with driver model.
This patch don't added dependency because when CONFIG_CLK
is not activated the clk function are stubbed.
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Use generic phy to initialize the PHY associated to the
DWC2 device and available in the device tree.
This patch don't added dependency because when CONFIG_PHY
is not activated, the generic PHY function are stubbed.
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Use ofnode_ instead of fdt_ APIs so that the drivers can support live DT.
This patch updates usb_get_dr_mode() and usb_get_maximum_speed() to use
ofnode as parameter instead of fdt offset. And all the drivers who use
these APIs update to use live dt APIs at the same time.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Use dev_read_addr_ptr() instead of devfdt_get_addr() so that we can support
live DT.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Rather than keeping the asynchronous schedule running always, keep it
running only across USB mass storage transfers for now, as it seems
that keeping it running all the time interferes with certain control
transfers during device enumeration.
Note that running the async schedule all the time should not be an
issue, especially on EHCI HCD, as that one implements most of the
transfers using async schedule.
Note that we have usb_disable_asynch(), which however is utterly broken.
The usb_disable_asynch() blocks the USB core from doing async transfers
by setting a global flag. The async schedule should however be disabled
per USB controller. Moreover, setting a global flag does not prevent the
controller from using the async schedule, which e.g. the EHCI HCD does.
This patch implements additional callback to the controller, which
permits it to lock the async schedule and keep it running across
multiple transfers. Once the schedule is unlocked, it must also be
disabled. This thus prevents the async schedule from running outside
of the USB mass storage transfers.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Tested-by: Tom Rini <trini@konsulko.com> [omap3_beagle, previously failing]
