Adds Support for Altera's Stratix II.
Within your board specific init file you will have to call
1. fpga_init (/* relocated code offset. usually => */ gd->reloc_off);
2. fpga_add (fpga_altera, (Altera_desc*)&altera_desc);
Altera_desc* contines (for example):
{
Altera_StratixII, /* part type */
passive_serial, /* interface type */
1, /* bytes of data part can accept */
(void *)(&funcs), /* interface function table */
0L, /* base interface address */
0 /* implementation specific cookie */
}
funcs is the interface. It is of type altera_board_specific_func.
It looks like this:
altera_board_specific_func func = {
pre_fn,
config_fn,
status_fn,
done_fn,
clk_fn,
data_fn,
abort_fn,
post_fn,
};
you will have to implement these functions, which is usually bit
banging some gpio.
Signed-off-by: Eran Liberty <liberty@extricom.com>
move the cmd_sata.c from common/ to drivers/ata_piix.c,
the cmd_sata.c have some part of ata_piix controller drivers.
consolidate the driver to have better framework.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Added the cpu command that provides a generic mechanism to get status,
reset, and release secondary cores in multicore processors.
Added support for using the ePAPR defined spin-table mechanism on 85xx.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add a simple expr style command that will set an env variable as the result
of the command. This allows us to do simple math in shell. The following
operations are supported: &, |, ^, +, -, *, /.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This moves the Blackfin-common bootldr command out of the BF537-STAMP
specific board directory and into the common directory so that all Blackfin
boards may utilize it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Move gunzip(), zalloc() and zfree() to a separate file.
Share zalloc() and zfree() with cramfs uncompress routine.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
- Add inline helper macros for basic header processing
- Move common non inline code common/image.c
- Replace direct header access with the API routines
- Rename IH_CPU_* to IH_ARCH_*
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
This patch adds a 'cu' like serial terminal command to u-boot
using which you can access other serial ports from the system console.
OpenMoko uses this in their Neo1973 phones to get access to the GSM
Modem and GPS chip from the bootloader.
Signed-off-by: Harald Welte <laforge@openmoko.org>
This change is in preparation for condtitionial compile support in the
build system. By spliting them all into seperate lines now, subsequent
patches that change 'COBJS-y += ' into 'COBJS-$(CONFIG_<blah>) += ' will
be less invasive and easier to review
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Bridge, ICH-5, ICH-6 and ICH-7.
Implementation:
1. Code is divided in to two files. All functions, which are
controller specific are kept in "drivers/ata_piix.c" file and
functions, which are not controller specific, are kept in
"common/cmd_sata.c" file.
2. Reading and Writing from the S-ATA drive is done using PIO method.
3. Driver can be configured for 48-bit addressing by defining macro
CONFIG_LBA48, if this macro is not defined driver uses the 28-bit
addressing.
4. S-ATA read function is hooked to the File system, commands like
ext2ls and ext2load file can be used. This has been tested.
5. U-Boot command "SATA_init" is added, which initializes the S-ATA
controller and identifies the S-ATA drives connected to it.
6. U-Boot command "sata" is added, which is used to read/write, print
partition table and get info about the drives present. This I have
implemented in same way as "ide" command is implemented in U-Boot.
7. This driver is for S-ATA in native mode.
8. This driver does not support the Native command queuing and
Hot-plugging.
Signed-off-by: Mushtaq Khan <mushtaq_k@procsys.com>
The code in this file is not a command; it is a device driver. Put it in
the correct place. There are zero functional changes in this patch, it
only moves the file.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Modifications are based on the linux kernel approach and
support two use cases:
1) Add O= to the make command line
'make O=/tmp/build all'
2) Set environement variable BUILD_DIR to point to the desired location
'export BUILD_DIR=/tmp/build'
'make'
The second approach can also be used with a MAKEALL script
'export BUILD_DIR=/tmp/build'
'./MAKEALL'
Command line 'O=' setting overrides BUILD_DIR environent variable.
When none of the above methods is used the local build is performed and
the object files are placed in the source directory.
Added code for reading and writing Mac addresses to/from ID EEPROM(0x57).
With attached patch, we can use command "mac/mac read/mac save/"
to read and write EEPROM under u-boot prompt.
U-boot will calculate the checksum of EEPROM while bootup,
if it is right, then u-boot will check whether the mac address
of eTSEC0/1/2/3 is availalbe (non-zero).
If there is mac address availabe in EEPROM, u-boot will use it,
otherewise, u-boot will use the mac address defined in
MPC8641HPCN.h. This matches the requirement to set unique mac address
for each TSEC port.
Signed-off-by: Haiying Wang <haiying.wang@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
* Patch by Hinko Kocevar, 21 Aug 2004:
- Group common framebuffer functions in common/lcd.c
- Group common framebuffer macros and #defines in include/lcd.h
- Provide calc_fbsize() for video ATAG
* Patch by Sascha Hauer, 28 Jun:
- add generic support for Motorola i.MX architecture
- add support for mx1ads, mx1fs2 and scb9328 boards
* Patches by Marc Leeman, 23 Jul 2004:
- Add define for the PCI/Memory Buffer Configuration Register
- corrected comments in cpu/mpc824x/cpu_init.c
* Add support for multiple serial interfaces
(for example to allow modem dial-in / dial-out)
Add Reiserfs support
* Patch by Hinko Kocevar, 20 Mar 2004
- Add auto-release for SMSC LAN91c111 driver
- Add save/restore of PTR and PNR regs as suggested in datasheet
Add support for NET+50 CPU and ModNET50 board
* Patch by Sam Song, 10 Feb 2004:
Fix typos in cfi_flash.c
* Patch by Leon Kukovec, 10 Feb 2004
Fixed long dir entry slot id calculation in get_vfatname
* Patch by Robin Gilks, 10 Feb 2004:
add "itest" command (operators: -eq, -ne, -lt, -gt, -le, -ge, ==,
!=, <>, <, >, <=, >=)
* Cleanup compiler warnings
* Fix problem with side effects in macros in include/usb.h
* Patch by David Benson, 13 Nov 2003:
bug 841358 - fix TFTP download size limit
* Fixing bug 850768:
improper flush_cache() in load_serial()
* Fixing bug 834943:
MPC8540 - missing volatile declarations
* Patch by Stephen Williams, 09 Feb 2004:
Add support for Xilinx SystemACE chip:
- New files common/cmd_ace.c and include/systemace.h
- Hook systemace support into cmd_fat and the partition manager
* Patch by Travis Sawyer, 09 Feb 2004:
Add bi_opbfreq & bi_iic_fast to 440GX bd_info as needed for Linux
update for for Atmel AT91RM9200DK development kit:
- support for environment variables in DataFlash
- Atmel DataFlash AT45DB1282 support
* Patch by Jeff Carr, 11 Nov 2003:
add support for new version of 8270 processors
* Patches by George G. Davis, 05 Nov 2003:
- only pass the ARM linux initrd tag to the kernel when an initrd
is actually present
- update omap1510inn configuration file
