Commit graph

7003 commits

Author SHA1 Message Date
Nobuhiro Iwamatsu
358d6ef32e arm: rmobile: lager: Enable CONFIG_SYS_GENERIC_BOARD
Add CONFIG_SYS_GENERIC_BOARD to use common/board_*.c for lager.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-21 10:10:06 +09:00
Nobuhiro Iwamatsu
71bb8c39e1 arm: rmobile: koelsch: Enable CONFIG_SYS_GENERIC_BOARD
Add CONFIG_SYS_GENERIC_BOARD to use common/board_*.c for koelsch.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-21 10:10:01 +09:00
Nobuhiro Iwamatsu
3f5f17a38f arm: rmobile: armadillo800eva: Enable CONFIG_SYS_GENERIC_BOARD
Add CONFIG_SYS_GENERIC_BOARD to use common/board_*.c for armadillo800eva.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-21 10:09:56 +09:00
Nobuhiro Iwamatsu
b6c96f7f35 arm: rmobile: koelsch: Add support ext4/fat write command
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-21 10:09:19 +09:00
Nobuhiro Iwamatsu
d80149b249 arm: rmobile: lager: Add support ext4/fat write command
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-21 10:09:19 +09:00
Nobuhiro Iwamatsu
f55bb6a4c4 arm: rmobile: lager: Add support command and filesystems of VFAT
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-21 10:09:19 +09:00
Nobuhiro Iwamatsu
5c4bb96e9c arm: rmobile: lager: Add support USB controller
Lager board has USB ports. This add support of USB controller of rmobile.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-21 10:09:19 +09:00
Nobuhiro Iwamatsu
fd77b2ebec arm: rmobile: koelsch: Add support command and filesystems of VFAT
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-21 10:09:19 +09:00
Nobuhiro Iwamatsu
aa44ae32e1 arm: rmobile: koelsch: Add support USB controller
Koelsch board has USB ports. This add support of USB controller of rmobile.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-21 10:09:19 +09:00
Nobuhiro Iwamatsu
7f922e32ff arm: rmobile: lager: Enable optimization of thumb
This adds CONFIG_SYS_THUMB_BUILD to config, in order to enable optimization
of thumb.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-21 10:09:19 +09:00
Nobuhiro Iwamatsu
05aad15bba arm: rmobile: lager: Remove CONFIG_USE_ARCH_MEMSET and MEMCPY
Because do not need these feature to lager board, this delete it.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-21 10:09:19 +09:00
Nobuhiro Iwamatsu
b923d4615f arm: rmobile: lager: Remove define of SCIF register
The define of SCIF register was already defined in rcar-base.h.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-21 10:09:19 +09:00
Nobuhiro Iwamatsu
e1ee37472b arm: rmobile: koelsch: Enable optimization of thumb
This adds CONFIG_SYS_THUMB_BUILD to config, in order to enable optimization
of thumb.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-21 10:09:19 +09:00
Nobuhiro Iwamatsu
a6318a8c61 arm: rmobile: koelsch: Remove CONFIG_USE_ARCH_MEMSET and MEMCPY
Because do not need these feature to koelsch board, this delete it.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-21 10:09:19 +09:00
Nobuhiro Iwamatsu
577d07ac9d arm: rmobile: koelsch: Remove define of SCIF register
The define of SCIF register was already defined in rcar-base.h.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-05-21 10:09:18 +09:00
Siva Durga Prasad Paladugu
1a897668ac fpga: Added support to load bit stream from SD/MMC
Added support to load a bitstream image in chunks by reading it in
chunks from SD/MMC.
Command format:
loadfs [dev] [address] [image size] [blocksize] <interface>
       [<dev[:part]>] <filename>
Example: fpga loadfs 0 1000000 3dbafc 4000 mmc 0 fpga.bin

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-05-20 15:23:46 +02:00
Michal Simek
26ea9ce5b8 zynq: Enable fpga loadp and loadbp commands
Use new fpga commands for loading partial bitstreams.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-05-20 15:23:46 +02:00
Siva Durga Prasad Paladugu
64e809afea fpga: Guard the LOADMK functionality with CMD_FPGA_LOADMK
Guard the LOADMK functionality with config to provide
an option to enable or disable it.
Enable it for all platforms in mainline which enable CONFIG_CMD_FPGA.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-05-20 15:23:46 +02:00
Michal Simek
d0db28f940 configs: iocom: Fix typo on CMD_FPGA command
Fix typo in CMD_FPGA command enabling.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-05-20 15:23:46 +02:00
Albert ARIBAUD
05d134b084 Merge remote-tracking branch 'u-boot/master'
Conflicts:
	boards.cfg

Conflicts were trivial once u-boot-arm/master boards.cfg was
reformatted (commit 6130c146) to match u-boot/master's own
reformatting (commit 1b37fa83).
2014-05-20 10:05:42 +02:00
Liu Gang
e4911815cf powerpc/srio-pcie-boot: Adjust addresses for SRIO/PCIE boot
The new 768KB u-boot image size requires changes for
SRIO/PCIE boot. These addresses need to be updated to
appropriate locations.

The updated addresses are used to configure the SRIO/PCIE
inbound windows for the boot, and they must be aligned
with the window size based on the SRIO/PCIE modules requirement.
So for the 768KB u-boot image, the inbound window cannot be set
with 0xfff40000 base address and 0xc0000 size, it should be
extended to 1MB size and the base address can be aligned with
the size.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-05-16 16:29:16 -05:00
Kim Phillips
3246584d19 mpc85xx: configs: remove c=ffe from default environment
AFAICT, c=ffe does nothing and was a typo from the original commit
d17123696c "powerpc/p4080: Add support
for the P4080DS board" and just kept on getting duplicated
in subsequently added board config files.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Edward Swarthout <ed.swarthout@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-05-16 16:27:05 -05:00
Prabhakar Kushwaha
bc2d40ca10 board/p1_p2_rdb:Enable p1_p2_rdb boot from NAND/SD/SPI in SPL
In the earlier patches, the SPL/TPL fraamework was introduced.
For SD/SPI flash booting way, we introduce the SPL to enable a loader stub. The
SPL was loaded by the code from the internal on-chip ROM. The SPL initializes
the DDR according to the SPD and loads the final uboot image into DDR, then
jump to the DDR to begin execution.

For NAND booting way, the nand SPL has size limitation on some board(e.g.
P1010RDB), it can not be more than 4KB, we can call it "minimal SPL", So the
dynamic DDR driver doesn't fit into this minimum SPL. We added the TPL that is
loaded by the the minimal SPL. The TPL initializes the DDR according to the SPD
and loads the final uboot image into DDR,then jump to the DDR to begin execution.

This patch enabled SPL/TPL for P1_P2_RDB to support starting from NAND/SD/SPI
flash with SPL framework and initializing the DDR according to SPD in the SPL/TPL.
Because the minimal SPL load the TPL to L2 SRAM and the jump to the L2 SRAM to
execute, so the section .resetvec is no longer needed.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-05-16 16:24:27 -05:00
Aneesh Bansal
3051f3f999 powerpc/mpc85xx: SECURE BOOT- corrected CSPR settings for BSC9132QDS NAND
In case of secure boot from NAND, CSPR and FTIM settings are
same as non-secure NAND boot. CSPR0 is configured as NAND and
CSPR1 is configured as NOR.

Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-05-16 16:24:27 -05:00
ramneek mehresh
80ba6a6f2a mpc85xx/p1020:Define number of USB controllers used on P1020RDB-PD platform
P1020 SoC which has two USB controllers, but only first one is used
on this platform.

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-05-16 16:24:27 -05:00
Chunhe Lan
1a344456a9 powerpc/85xx: Add T4160RDB board support
T4160RDB shares the same platform as T4240RDB. T4160 is
a low power version of T4240, with the eight e6500 cores,
two DDR3 controllers, and same peripheral bus interfaces.

Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-05-16 16:24:26 -05:00
Albert ARIBAUD
a26acb7dc9 Merge remote-tracking branch 'u-boot-sh/rmobile'
Conflicts:
	boards.cfg

Trivial conflict, maintainer change plus board addition
2014-05-16 20:43:04 +02:00
Albert ARIBAUD
6a2f30a03a Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2014-05-16 17:56:50 +02:00
Albert ARIBAUD
a90bed77a6 Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2014-05-16 16:49:50 +02:00
Jaehoon Chung
e33daad0b7 ARM: exynos4: enable the dwmmc configuration
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-16 14:54:26 +09:00
Mateusz Zalega
d2f588f3b8 arm: goni: enable USB Mass Storage
UMS-related defines were added to Samsung Goni config header.

Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-16 13:35:54 +09:00
Mateusz Zalega
a3c274de3b arm: goni: enable GPT command
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-16 13:35:54 +09:00
Mateusz Zalega
2d281b3252 arm: goni: dfu: Add support for DFU to Goni target
Proper adjustment for supporting DFU at GONI target has been made.
The s5p_goni.h file has been updated. Moreover the code for low level
USB initialization has been added to GONI board code.

The malloc pool has been enlarged in order to support larger buffer
sizes needed by DFU implementation.

Signed-off-by: Arkadiusz Wlodarczyk <a.wlodarczyk@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Tested-by: Arkadiusz Wlodarczyk <a.wlodarczyk@samsung.com>
Tested-by: Mateusz Zalega <m.zalega@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-16 13:35:54 +09:00
Mateusz Zalega
a45ddf7a3e arm: goni: Update configuration for Goni target
Configuration file for GONI has been updated to support FAT file system,
new mmc partitioning scheme and read linux kernel from eMMC instead of
OneNAND.

Signed-off-by: Arkadiusz Wlodarczyk <a.wlodarczyk@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Tested-by: Arkadiusz Wlodarczyk <a.wlodarczyk@samsung.com>
Tested-by: Mateusz Zalega <m.zalega@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-16 13:35:54 +09:00
Albert ARIBAUD
44cfc3a83f Merge branch 'u-boot-tegra/master' into 'u-boot-arm/master' 2014-05-15 17:19:45 +02:00
Albert ARIBAUD
9f5f51540d Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master' 2014-05-15 16:36:02 +02:00
Masahiro Yamada
0dfbcf02de zynq: load u-boot-dtb.img if CONFIG_OF_SEPARATE is defined
SPL should load "u-boot-dtb.img" if both CONFIG_OF_CONTROL
and CONFIG_OF_SEPARATE are defined.
Otherwise, "u-boot.img" should be loaded.

Since CONFIG_OF_CONTROL is always undefined for SPL_BUILD,
the undef block should be moved below the conditional definition
of CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-05-15 13:57:28 +02:00
Stefano Babic
e7f9350525 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-05-15 10:27:32 +02:00
Michal Simek
841426ad9f ARM: zynq: Extend maximum number of command arguments
15 was too small for variables stored in file on MMC.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-05-14 07:46:40 +02:00
Siva Durga Prasad Paladugu
2e38a90672 ARM: zynq: Enable EXT4 configs
Enabled the EXT4 configs.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-05-14 07:43:35 +02:00
Siva Durga Prasad Paladugu
47b35a516b ARM: zynq: Move USB/SD/MMC common FAT configs
Moved the USB/SD/MMC common FAT configs separately
to avoid redefinition warnings.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-05-14 07:43:35 +02:00
Siva Durga Prasad Paladugu
00cf6b4e22 ARM: zynq: Enable the FAT write capability
Enable the FAT write capability for SD/MMC write
functionality.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-05-14 07:43:35 +02:00
Siva Durga Prasad Paladugu
c6024c8edd ARM: zynq: Added USB host support for zynq boards
Added configs to support USB host for zynq boards.
Also added a command usbboot to boot from usb.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-05-14 07:43:35 +02:00
Michal Simek
3d456eec43 ARM: zynq: Extend kernel image size to 60MB
Extend max kernel image size. Gunzip is checking
this value. If kernel is larger, message below is shown.

Uncompressing Kernel Image ... Error: inflate() returned -5
GUNZIP: uncompress, out-of-mem or overwrite error -
must RESET board to recover

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-05-14 07:43:34 +02:00
Michal Simek
1540fb725b ARM: zynq: Call zynq board_init() in SPL
Call board_init() if SPL is configured with CONFIG_SPL_BOARD_INIT.

Signed-off-by: Michal Simek <monstr@monstr.eu>
2014-05-14 07:43:34 +02:00
Ash Charles
2d92ba8440 am335x: pepper: Add Gumstix Pepper AM335x-based machine
This adds the Gumstix Pepper[1] single-board computer based on the
TI AM335x processor. Schematics are available [2].

[1] https://store.gumstix.com/index.php/products/344/
[2] https://pubs.gumstix.com/boards/PEPPER/

Signed-off-by: Ash Charles <ash@gumstix.com>
[trini: Move 'cdev' in board.c down to under #ifdef's where it's used]
Signed-off-by: Tom Rini <trini@ti.com>
2014-05-13 19:47:51 -04:00
Christian Riesch
532d531828 arm, davinci: Use CONFIG_SPL_PAD_TO for padding the SPL in an ais image
The commits

commit b7b5f1a16c
Author: Albert ARIBAUD <albert.u.boot@aribaud.net>
da850evm, da850_am18xxevm: convert to CONFIG_SPL_MAX_FOOTPRINT

and

commit e7497891e3
Author: Albert ARIBAUD <albert.u.boot@aribaud.net>
cam_enc_4xx: convert to CONFIG_SPL_MAX_FOOTPRINT

replaced CONFIG_SPL_MAX_SIZE by CONFIG_SPL_MAX_FOOTPRINT. However,
CONFIG_SPL_MAX_SIZE is used in the Makefile for padding the SPL
when preparing an u-boot.ais image. By removing CONFIG_SPL_MAX_SIZE
said commits broke the ais image of the da850evm and cam_enc_4xx
configurations.

This patch converts the u-boot.ais target to use CONFIG_SPL_PAD_TO
instead of CONFIG_SPL_MAX_SIZE for padding the SPL and adds
a #define CONFIG_SPL_PAD_TO where it is required.

Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Reported-by: Tom Taylor <ttaylor.tampa@gmail.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-05-13 19:43:01 -04:00
Egli, Samuel
f04776b6d8 siemens, draco: add new target
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Reviewed-by: Roger Meier <r.meier@siemens.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
2014-05-13 19:43:01 -04:00
Robert Nelson
4fa2427c5d omap3_beagle: xM A/B validate new dtb exits in file system
Fall back to previous dtb used when omap3-beagle-xm-ab.dtb doesn't exist in file system

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tom Rini <trini@ti.com>
CC: Nishanth Menon <nm@ti.com>
Acked-by: Tom Rini <trini@ti.com>
2014-05-13 19:43:00 -04:00
Robert Nelson
3d47ffb993 omap3_beagle: use omap3-beagle-xm-ab.dtb for the xM AB revision
As of v3.15-rc3, omap3-beagle-xm-ab.dtb now exists with the usb hub (ehci) enabled.

For older kernels versions, cherry pick from mainline:
ef78f3869c37c480f1d58462a760a40dabc823f4

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tom Rini <trini@ti.com>
CC: Nishanth Menon <nm@ti.com>
2014-05-13 19:43:00 -04:00
Egli, Samuel
66c45faefb siemens: cosmetic: rename project_dir
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
2014-05-13 19:43:00 -04:00
Egli, Samuel
84112b5171 siemens: change LED indication in DFU mode
In order to have the same LED indication like in another product
when ready for updating, enable only red led and disable status
LED when entering DFU mode.

The status LED is only switched off when defined in board file.

Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
2014-05-13 19:43:00 -04:00
Egli, Samuel
9fc2ed40cd siemens: cosmetic: remove unused and rename defines
For dxr2 board DXR2_IOCTRL_VAL is set by data in EEPROM. In pxm2
board it does not make sense to have dxr2 as prefix. Replace it with
more meaningful DDR prefix.

Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Cc: Pascal Bach <pascal.bach@siemens.com>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
2014-05-13 19:42:59 -04:00
Khoronzhuk, Ivan
0eaf416eea config: k2hk_evm: Add generic board support
We should use generic board in order the ARM maintainer
be able to remove arch/arm/lib/board.c

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-05-13 18:04:07 -04:00
Stephen Warren
2364e151e4 ARM: tegra: use a CPU freq that all SKUs can support
U-Boot on Tegra30 currently selects a main CPU frequency that cannot be
supported at all on some SKUs, and needs higher VDD_CPU/VDD_CORE values
on some others. This can result in unreliable operation of the main CPUs.

Resolve this by switching to a CPU frequency that can be supported by any
SKU. According to the following link, the maximum supported CPU frequency
of the slowest Tegra30 SKU is 600MHz:

repo http://nv-tegra.nvidia.com/gitweb/?p=linux-2.6.git;a=summary
branch l4t/l4t-r16-r2
path arch/arm/mach-tegra/tegra3_dvfs.c
table cpu_dvfs_table[]

According to that same table, the minimum VDD_CPU required to operate at
that frequency across all SKUs is 1.007V. Given the adjustment resolution
of the TPS65911 PMIC that's used on all Tegra30-based boards we support,
we'll end up using 1.0125V instead.

At that VDD_CPU, tegra3_get_core_floor_mv() in that same file dictates
that VDD_CORE must be at least 1.2V on all SKUs. According to
tegra_core_speedo_mv() (in tegra3_speedo.c in the same source tree),
that voltage is safe for all SKUs.

An alternative would be to port much of the code from tegra3_dvfs.c and
tegra3_speedo.c in the kernel tree mentioned above. That's more work
than I want to take on right now.

While all the currently supported boards use the same regulator chip for
VDD_CPU, different types of regulators are used for VDD_CORE. Hence, we
add some small conditional code to select how VDD_CORE is programmed. If
this becomes more complex in the future as new boards are added, or we
end up adding code to detect the SoC SKU and dynamically determine the
allowed frequency and required voltages, we should probably make this a
runtime call into a function provided by the board file and/or relevant
PMIC driver.

Cc: Alban Bedel <alban.bedel@avionic-design.de>
Cc: Marcel Ziswiler <marcel@ziswiler.com>
Cc: Bard Liao <bardliao@realtek.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-05-13 10:41:32 -07:00
Stephen Warren
f175603f7c ARM: tegra: set CONFIG_SYS_MMC_MAX_DEVICE
If CONFIG_API is ever to be enabled on Tegra, this define must be set,
since api/api_storage.c uses it.

A couple of annoyting things about CONFIG_SYS_MMC_MAX_DEVICE

1) It isn't documented in README. The same is true for a lot of similar
   defines used by api_storage.c.

2) It doesn't represent MAX_DEVICE but rather NUM_DEVICES, since the
   valid values are 0..n-1 not 0..n.

However, I this patch does not address those shortcomings.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-05-13 10:41:31 -07:00
York Sun
15672c6dbd powerpc/freescale: Convert selected boards to generic board architecture
This patch converts the following boards to use generic board: MPC8536DS,
MPC8572DS, MPC8641HPCN, p1_p2_rdb_pc, corenet_ds, t4qds, B4860QDS. It has
been tested on NOR boot on MPC8536DS, MPC8572DS, P1021RDB, P4080DS,
P5020DS, P5040DS, P3041DS, T4240QDS, B4860QDS.

Signed-off-by: York Sun <yorksun@freescale.com>
CC: Ying Zhang <b40530@freescale.com>
CC: Prabhakar Kushwaha <prabhakar@freescale.com>
CC: Haijun.Zhang <Haijun.Zhang@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
CC: Shaohui Xie <Shaohui.Xie@freescale.com>
2014-05-13 08:31:22 -07:00
York Sun
18025756b5 powerpc/mpc8572ds: Increase u-boot size to 768KB
U-boot image has grown and exceeded the predefined 512KB. Increasing to
768KB to align with other powerpc boards. Tested on MPC8572DS for 32-
and 36-bit targets with NOR flash boot. NAND boot is not covered by
this patch.

Also update board maintainer for these boards.

Signed-off-by: York Sun <yorksun@freescale.com>
Acked-by: Heiko Schocher <hs@denx.de>
2014-05-13 08:31:22 -07:00
Alexander Graf
eab3bfbcd1 PPC 85xx QEMU: Make a generic board file
This patch enables the E500 QEMU board to use the generic cross-arch board
infrastructure.

Signed-off-by: Alexander Graf <agraf@suse.de>
2014-05-13 08:26:56 -07:00
Valentin Longchamp
522641a788 kmp204x: enable the errata command
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-05-13 08:26:55 -07:00
Valentin Longchamp
848b31ab0f kmp204x: update the CONFIG_PRAM and CONFIG_KM_RESERVED_PRAM defines
This prevents u-boot from accessing into the reserved memory areas that
we have for /var and the logbooks.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-05-13 08:26:55 -07:00
Valentin Longchamp
18794944c6 kmp204x: selftest/factory test pin support
This patch defines the post_hotkeys_pressed() function that is used for:
- triggering POST memory regions test
- starting the test application through the checktestboot command in
  a script by setting the active bank to testbank

The post_hotkeys_pressed return the state of the SELFTEST pin.

The patch moves from the complete POST-memory test that is too long in
its SLOW version for our production HW test procedure to the much shorter
POST-memory-regions test.

Finally, the unused #defines for the not so relevant mtest command are
removed.

Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-05-13 08:26:55 -07:00
Shengzhou Liu
c665c473b6 powerpc/t208x: enable errata A006261, A006593, A006379
Enable errata A006261, A006593, A006379 for T208x.
Additionally enable CONFIG_CMD_ERRATA for T2080RDB.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
2014-05-13 08:26:54 -07:00
Chunhe Lan
0b2e13d9cc powerpc/85xx: Add T4240RDB board support
T4240RDB board Specification
----------------------------
Memory subsystem:
   6GB DDR3
   128MB NOR flash
   2GB NAND flash

Ethernet:
   Eight 1G SGMII ports
   Four 10Gbps SFP+ ports

PCIe:
   Two PCIe slots

USB:
   Two USB2.0 Type A ports

SDHC:
   One SD-card port

SATA:
   One SATA port

UART:
   Dual RJ45 ports

Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
[York Sun: fix CONFIG_SYS_QE_FMAN_FW_ADDR in T4240RDB.h]
2014-05-13 08:24:32 -07:00
Shaveta Leekha
652e29b4a0 board/b4qds: VID support
The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory.
These values define the voltage requirements for
the chip. u-boot reads FUSESR and translates the values
into the appropriate commands to set the voltage output
value of an external voltage regulator.

B4860QDS has a PowerOne ZM7300 programmable digital Power
Manager which is programmed as per the value read from
the fuses.

Reference for this code is taken from t4qds VID implementation.

Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
2014-05-13 08:20:31 -07:00
Akshay Saraswat
9b97b727dc S5P: Exynos: Config: Enable GPIO CMD config
Enabling configs for GPIO CMD, EXYNOS4 family and replacing
exynos_gpio_get with new linear GPIO pin number required
because of the new function asking only 2 arguments (pin
and value) instead of 3 (bank, pin and value).

Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-13 15:20:38 +09:00
Akshay Saraswat
e6fe968b82 Exynos5: config: Enable FIT
Adding two configs:
* CONFIG_FIT - Enable FIT image support.
* CONFIG_FIT_BEST_MATCH - Enable fetching correct DTB from
			  FIT image by comparing compatibles.

Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-13 09:00:22 +09:00
Masahiro Yamada
488c47a141 config: remove platform CONFIG_SYS_HZ definition part 4
Some new boards define CONFIG_SYS_HZ again! Remove.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
2014-05-12 15:20:05 -04:00
Masahiro Yamada
c42f56d96d blackfin: replace bfin_gen_rand_mac() with eth_random_addr()
bfin_gen_rand_mac() uses __DATE__ as the seed for random ethernet
address. This makes the build non-deterministic.

In the first place, it should not be implemented as a Bfin-specific
function. Use eth_random_addr() instead.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
2014-05-12 15:19:46 -04:00
Tom Rini
f4617ef86d Merge branch 'tom' of git://git.denx.de/u-boot-x86 2014-05-09 18:48:26 -04:00
Simon Glass
ad0e463954 sandbox: Provide a build option to avoid using SDL
Some machines do not have SDL libraries installed, and it is still useful
to build sandbox without LCD/keyboard support.

Add an option for this, used as follows:

    make sandbox_config all NO_SDL=1

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-05-09 14:47:13 -06:00
Otavio Salvador
0ef797a59e wandboard: Pass video kernel arguments for HDMI and LCD
This checks if the 7" WVGA produced by Future Eletronics is detected
and pass the needed kernel arguments for it to work.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2014-05-09 15:21:25 +02:00
Otavio Salvador
8bc7c48749 wandboard: add Future Eletronics 7" WVGA LCD extension board
This adds support for the 7" WVGA produced by Future Eletronics and
make it dynamically detect if it is connected or not based on the
touchscreen controller.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
2014-05-09 15:21:16 +02:00
Tim Harvey
7a278f9f1b imx: ventana: add HDMI and LVDS display capability
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2014-05-09 15:10:54 +02:00
Tim Harvey
effb7dc6d9 imx: ventana: Convert to generic board
Enable CONFIG_SYS_GENERIC_BOARD on ventana.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2014-05-09 15:10:54 +02:00
Tim Harvey
234d89dac6 ventana: Add support for the LTC3676 PMIC
The LTC3676 PMIC is used instead of the PFUZE100 PMIC on the
GW51xx/GW52xx/GW53xx Ventana baseboards. In order to support the IMX6Q SoC
at 1GHz on those baseboards, we need to adjust the voltage scaling for the SW1
and SW3 DC/DC converters on the LTC3676 for 1225mV. Note that the scalar
values for the LTC3676 are board-specific as they relate to a resistor devider
chosen by the board design.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2014-05-09 15:10:43 +02:00
Albert ARIBAUD
d2a3e91139 Merge branch 'u-boot/master'
Conflicts:
	drivers/net/Makefile

(trivial merge)
2014-05-09 11:50:14 +02:00
Rob Herring
dd5b68fba7 arm: beagle: enable Android fastboot support
Enable Android Fastboot support on omap3_beagle board.

Signed-off-by: Rob Herring <robh@kernel.org>
2014-05-08 10:38:30 +02:00
Jaehoon Chung
188c42b335 ARM: exynos: remove the unused code
"mmc boot" command didn't use anywhere.
It can be replace "mmc dev" command.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-07 17:05:21 +09:00
Łukasz Majewski
6afc3f6e11 trats: config: fix: Set default console to ttySAC2
During providing device tree support for Exynos4 based boards,
a tiny mistake has creeped in the fe60164 commit.

This commit restores proper setting of default console for the
trats board.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-07 15:25:42 +09:00
Łukasz Majewski
2ee93246bd trats2: config: fix: Set default console to ttySAC2
During providing device tree support for Exynos4 based boards,
a tiny mistake has creeped in the 1ecab0f commit.

This commit restores proper setting of default console for the
trats2 board.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-07 15:25:42 +09:00
Tom Rini
33b0f7b5e6 Merge branch 'master' of git://www.denx.de/git/u-boot-microblaze 2014-05-06 14:55:27 -04:00
Stephan Linz
d1d37b5cab microblaze: Wire up OF support for emaclite
- expand the condition with CONFIG_OF_CONTROL

Signed-off-by: Stephan Linz <linz@li-pro.net>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-05-06 13:32:30 +02:00
Mateusz Zalega
fad8edf0f7 am335x: dfu: disable DFU in am335x_evm SPL build
Future patches will make DFU too large to fit in this board's SPL build.

Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Acked-by: Tom Rini <trini@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2014-05-05 08:21:47 +02:00
Mateusz Zalega
b7d4259af2 dfu: mmc: change offset base handling
Previously offsets handled by dfu_fill_entity_mmc(), defined in boards'
CONFIG_DFU_ALT were treated as hexadecimal regardless of their prefix,
which sometimes led to confusion. This patch forces usage of explicit
numerical base prefixes.

Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Tom Rini <trini@ti.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
2014-05-05 08:20:56 +02:00
Mateusz Zalega
75504e9592 usb: dfu: fix boards wo USB cable detection
Former usb_cable_connected() patch broke compilation of boards which do
not support this feature.

I've renamed usb_cable_connected() to g_dnl_usb_cable_connected() and added
its default implementation to gadget downloader driver code. There's
only one driver of this kind and it's unlikely there'll be another, so
there's no point in keeping it in /common.

Previously this function was declared in usb.h. I've moved it, since
it's more appropriate to keep it in g_dnl.h - usb.h seems to be intended
for USB host implementation.

Existing code, confronted with default -EOPNOTSUPP return value,
continues as if the cable was connected.

CONFIG_USB_CABLE_CHECK was removed.

Change-Id: Ib9198621adee2811b391c64512f14646cefd0369
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
2014-05-05 08:00:28 +02:00
Rob Herring
7904b70885 ARM: highbank: use default prompt
Since highbank is actually shared between Highbank and Midway platforms,
remove the Highbank name from the prompt and use the default.

Signed-off-by: Rob Herring <robh@kernel.org>
2014-05-02 11:43:25 +02:00
Rob Herring
ac9ae1333e ARM: highbank: use config_distro_defaults.h
Adapt highbank to use config_distro_defaults.h and remove the redundant
defines.

Signed-off-by: Rob Herring <robh@kernel.org>
2014-05-02 11:43:11 +02:00
Stefano Babic
3deb22a484 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-04-29 17:41:19 +02:00
Fabio Estevam
694c3bc107 mx6slevk: Add SPI NOR flash support
mx6slevk has a m25p32 SPI NOR flash connected to ESCSPI port.

Add support for it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-04-28 14:00:16 +02:00
Marek Vasut
0782bdf898 arm: mxs: Enable CONFIG_SYS_GENERIC_BOARD
Signed-off-by: Marek Vasut <marex@denx.de>
2014-04-28 13:56:42 +02:00
Eric Nelson
f7155fa3f0 ARM: imx6: nitrogen6x: Enable CONFIG_SYS_GENERIC_BOARD
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on
boot:

"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-04-28 11:05:42 +02:00
Fabio Estevam
518d225c43 hummingboard: Convert to generic board
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on
boot:

"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-04-28 10:45:56 +02:00
Fabio Estevam
a980d1e469 udoo: Convert to generic board
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on
boot:

"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-04-28 10:45:56 +02:00
Fabio Estevam
851f556af0 mx53evk: Convert to generic board
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on
boot:

"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-04-28 10:45:56 +02:00
Fabio Estevam
5a416df0e1 mx53smd: Convert to generic board
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on
boot:

"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-04-28 10:45:55 +02:00
Fabio Estevam
4677b1b605 mx53ard: Convert to generic board
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on
boot:

"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-04-28 10:45:55 +02:00
Fabio Estevam
12be4cbe7c mx6sabre_common: Convert to generic board
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on
boot:

"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-04-28 10:45:55 +02:00
Fabio Estevam
6ca896f923 mx53loco: Convert to generic board
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on
boot:

"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-04-28 10:45:55 +02:00
Fabio Estevam
7f5d0af874 wandboard: Convert to generic board
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on
boot:

"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-04-28 10:45:55 +02:00
Nobuhiro Iwamatsu
8d18bcfd43 arm: rmobile: lager: Remove MACH_TYPE_LAGER and CONFIG_MACH_TYPE
MACH_TYPE_LAGER and CONFIG_MACH_TYPE are not already available on Lager board.
This removes them.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-04-28 04:35:12 +09:00
Nobuhiro Iwamatsu
b1f78a2ebd arm: rmobile: lager: Update calculation of CONFIG_SH_TMU_CLK_FREQ
CONFIG_SH_TMU_CLK_FREQ of lager is calculated from the external clock.
This defines RMOBILE_XTAL_CLK, this updates the calculation of
CONFIG_SH_TMU_CLK_FREQ.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-04-28 04:35:12 +09:00
Nobuhiro Iwamatsu
ae8e1d9d7d arm: rmobile: koelsch: Update calculation of CONFIG_SH_TMU_CLK_FREQ
CONFIG_SH_TMU_CLK_FREQ of koelsch is calculated from the external clock.
This defines RMOBILE_XTAL_CLK, this updates the calculation of
CONFIG_SH_TMU_CLK_FREQ.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-04-28 04:35:12 +09:00
Nobuhiro Iwamatsu
9e018b092a arm: rmobile: lager: Remove NOR-Flash support
Lagar board has NOR-Flash. But user uses SPI-Flash ROM instead of NOR-Flash.
This removed the setting of NOR-Flash.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-04-28 04:35:12 +09:00
Nobuhiro Iwamatsu
e44154ef0a arm: rmobile: koelsch: Remove NOR-Flash support
Koelsch board has NOR-Flash. But user uses SPI-Flash ROM instead of NOR-Flash.
This removed the setting of NOR-Flash.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-04-28 04:35:12 +09:00
Tom Rini
8854070784 Merge branch 'master' of git://www.denx.de/git/u-boot-arc 2014-04-25 15:08:43 -04:00
Tom Rini
b71bf4add6 Merge branch 'master' of git://git.denx.de/u-boot-mpc83xx 2014-04-25 14:57:58 -04:00
Tom Rini
080d897585 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2014-04-25 14:53:51 -04:00
Alexey Brodkin
0cdd762027 axs101: bump DDR size from 256 to 512 Mb
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2014-04-25 18:00:23 +04:00
Alexey Brodkin
6bfa44206e axs101: increase EEPROM page write delay from 32 to 64 msec
With 32 milliseconds delay on some boards EEMPROM got written inconsistently.
With 64 msec all of our existig boards show properly written EEPROM.

Cc: Tom Rini <trini@ti.com>

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2014-04-25 18:00:16 +04:00
Heiko Schocher
eaf8c986d3 mpc83xx: add ids8313 support
add support for the ids8313 board.

CPU:   e300c3, MPC8313, Rev: 2.1 at 396 MHz, CSB: 132 MHz
I2C:   ready
SPI:   ready
DRAM:  128 MiB (DDR2, 32-bit, ECC off, 264 MHz)
Flash: 8 MiB
NAND:  128 MiB
Net:   TSEC0, TSEC1 [PRIME]

public key on NOR flash start

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2014-04-23 19:07:54 -05:00
Shaohui Xie
b6036993eb powerpc/T4QDS: add two stage boot of nand/sd
Add support of 2 stage NAND/SD boot loader using SPL framework.
PBL initialise the internal SRAM and copy SPL, this further
initialise DDR using SPD and environment and copy u-boot from
NAND/SD to DDR, finally SPL transfer control to u-boot.
NOR uses CS1 instead of CS2 when NAND boot, fix it.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:53 -07:00
Shengzhou Liu
ef531c7357 board/t2080rdb: some update for t2080rdb
- update readme.
- add CONFIG_SYS_CORTINA_FW_IN_* for loading Cortina PHY CS4315
  ucode from NOR/NAND/SPI/SD/REMOTE.
- update cpld vbank with SW3[5:7]=000 as default vbank0 instead of
  previous SW3[5:7]=111 as default vbank.
- fix CONFIG_SYS_I2C_EEPROM_ADDR_LEN to 2.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:52 -07:00
Shengzhou Liu
4d66668300 board/t208xrdb: Add support of 2-stage NAND/SPI/SD boot
Add support of 2-stage NAND/SPI/SD boot loader using SPL framework.
PBL initializes the internal CPC-SRAM and copy SPL(160K) to it,
SPL further initializes DDR using SPD and environment and copy
u-boot(768K) from SPI/SD/NAND to DDR, finally SPL transfers control
to u-boot.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:52 -07:00
Shengzhou Liu
b19e288f47 board/t208xqds: Add support of 2-stage NAND/SPI/SD boot
Add support of 2-stage NAND/SPI/SD boot loader using SPL framework.
PBL initializes the internal CPC-SRAM and copy SPL(160K) to it,
SPL further initializes DDR using SPD and environment and copy
u-boot(768 KB) from SPI/SD/NAND to DDR, finally SPL transfers
control to u-boot.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: fix boards.cfg for T2081QDS_SDCARD and _SPIFLASH]
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:52 -07:00
Haijun.Zhang
e2c9bc5ea6 Powerpc/mpc8536DS: Increase SPI/SD uboot Image size to 768K
u-boot binary size for Freescale mpc8536DS platforms is 512KB.
This has been reached to upper limit of the platforms and causig
linker error. So increase the u-boot binary size to 768KB.

Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:51 -07:00
Prabhakar Kushwaha
9307cbaba9 powerpc/mpc85xx:Update MONITOR_LEN for 768KB u-boot size
U-boot binary size has been increased from 512KB to 768KB.

So update CONFIG_SYS_MONITOR_LEN to reflect the same.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:51 -07:00
Prabhakar Kushwaha
18c0144542 board/t104xrdb: Add support of NAND, SD, SPI boot for T104xRDB
Add support of 2 stage NAND, SD, SPI boot loader using SPL framework.
here, PBL initialise the internal SRAM and copy SPL(160KB). This further
initialise DDR using SPD and environment and copy u-boot(768 KB) from NAND to DDR.
Finally SPL transer control to u-boot.

Initialise/create followings required for SPL framework
      - Add spl.c which defines board_init_f, board_init_r
      - update tlb and ddr accordingly

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:51 -07:00
Prabhakar Kushwaha
c5dfe6ec58 board/b4qds:Add support of 2 stage NAND boot-loader
Add support of 2 stage NAND boot loader using SPL framework.
here, PBL initialise the internal SRAM and copy SPL(160KB). This further
initialise DDR using SPD and environment and copy u-boot(768 KB) from NAND to DDR.
Finally SPL transer control to u-boot.

Initialise/create followings required for SPL framework
  - Add spl.c which defines board_init_f, board_init_r
  - update tlb and ddr accordingly

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:51 -07:00
Prabhakar Kushwaha
099b86b7e7 board/t1042rdb_pi: Disable CONFIG_QE and CONFIG_U_QE
T1042RDB_PI board does not have QE connector.

So disable CONFIG_QE and CONFIG_U_QE for T1042RDB_PI

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:49 -07:00
Zhao Qiang
6259e29134 T1040QDS/U-QE: Add u-qe support to t1040qds
Add u-qe support for t1040qds

Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:49 -07:00
Tang Yuantian
5303a3dea9 mpc85xx: Add deep sleep support on T104xRDB
Add deep sleep support on T104xRDB platforms.

Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:49 -07:00
Tang Yuantian
48f6a9a2bf mpc85xx: Add deep sleep support on T1040QDS
Add deep sleep support on T1040QDS platform.

Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:49 -07:00
Prabhakar Kushwaha
55153d6c30 board/t104xrdb: Add support of CPLD
T1040RDB and T1042RDB_PI has CPLD. Here CPLD controls board mux/features.

This support of CPLD includes
 - files and register defintion
 - Commands to swtich alternate bank and default bank

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:48 -07:00
Prabhakar Kushwaha
68b747397b powerpc/T1040: add mtdparts suppport for T104xRDB and T1040QDS
We use dynamical mtdparts partition instead of directly puting
mtd partitions nodes in device tree.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:48 -07:00
Shengzhou Liu
4feac1c661 powerpc/T208xRDB: add mtdparts suppport
We use dynamical mtdparts partition instead of directly puting
mtd partitions nodes in device tree.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:48 -07:00
Shengzhou Liu
9941cf781f powerpc/T208xQDS: add mtdparts suppport
We use dynamical mtdparts partition instead of directly puting
mtd partitions nodes in device tree.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:48 -07:00
vijay rai
f4c3917a3c powerpc/t104xrdb: Unification of T104xRDB header files
T1040RDB, T1042RDB header files are very similar so merged into new header file T104xRDB.
T104xRDB header file can support both T1040RDB and T1042RDB_PI header.

Patch makes following changes
-Update Boards.cfg file for T1040RDB and T1042RDB_PI
-Add new T104xRDB header file
-Delete T1040RDB, T1042RDB_PI header file

Signed-off-by: Vijay Rai <vijay.rai@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:48 -07:00
Shengzhou Liu
22cbf96434 powerpc/t208xqds: fix nor chip selection when nand boot
NOR flash is on CS1 instead of CS2 when NAND boot.
So correct NOR chip selection to CS1 from CS2.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:48 -07:00
York Sun
c60dee03c0 mpc85xx/T1040QDS_D4: Add DDR4 support
T1040QDS_D4 is a variant of T1040QDS, with additional circuit to support
DDR4 memory. Tested with MTA9ASF51272AZ-2G1AYESZG.

Signed-off-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:48 -07:00
Zhao Qiang
59ff5d3306 t1040rdb/qe: add QE support for T1040RDB
add CONFIG_QE, CONFIG_U_QE and CONFIG_SYS_QE_FW_ADDR into
"include/configs/T1040RDB.h"

Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:47 -07:00
Zhao Qiang
dcf1d774bf QE/FMAN: modify CONFIG_SYS_QE_FMAN_FW_ADDR to CONFIG_SYS_FMAN_FW_ADDR and CONFIG_SYS_QE_FW_ADDR
CONFIG_SYS_QE_FMAN_FW_ADDR is used to both Fman and QE for microcode address.
Now using CONFIG_SYS_FMAN_FW_ADDR for Fman microcode address,
and CONFIG_SYS_QE_FW_ADDR for QE microcode address.

Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:47 -07:00
Aneesh Bansal
bea3cbb07f powerpc/mpc85xx: SECURE BOOT- Add NAND secure boot target for BSC9132QDS
In case of secure boot from NAND, the DDR is initialized by the
BootROM using the config words (CF_WORDS) in the CF_HEADER
and u-boot image is copied from NAND to DDR by the BootROM.
So, CONFIG_SYS_RAMBOOT has been defined for Secure Boot from NAND

Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:46 -07:00
Aneesh Bansal
f978f7c203 powerpc/mpc85xx: SECURE BOOT- Add secure boot target for BSC9132QDS
Add NOR, SPI and SD secure boot targets for BSC9132QDS.

Changes:
- Debug TLB entry is not required for Secure Boot Target.

Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:46 -07:00
Aneesh Bansal
50c7636764 powerpc/p1010rdb: SECURE BOOT- enable workaround for IFC errata A003399
The workaround for IFC errata A003399 was not enabled
in case of secure boot. So, secure boot from NOR was not
working.

Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:46 -07:00
Aneesh Bansal
76c9aaf587 powerpc/p1010rdb: SECURE BOOT enabled for NAND
In case of secure boot from NAND, the DDR is initialized by the
BootROM using the config words (CF_WORDS) in the CF_HEADER
and u-boot image is copied from NAND to DDR by the BootROM.
So, CONFIG_SYS_RAMBOOT has been defined for Secure Boot from NAND.

Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:45 -07:00
Alexander Graf
fa08d39517 PPC 85xx: Add qemu-ppce500 machine
For KVM we have a special PV machine type called "ppce500". This machine
is inspired by the MPC8544DS board, but implements a lot less features
than that one.

It also provides more PCI slots and is supposed to be enumerated by
device tree only.

This patch adds support for the generic ppce500 machine and tries to
rely solely on device tree for device enumeration.

Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:45 -07:00
Albert ARIBAUD
c9aab0f9dd Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2014-04-21 21:01:35 +02:00
Albert ARIBAUD
94b972d366 Merge branch 'u-boot-tegra/master' into 'u-boot-arm/master' 2014-04-21 20:13:48 +02:00
Daniel Schwierzeck
538cf92c8c MIPS: drop incaip board
This is dead hardware and no one is interested in making the
necessary changes for upcoming features like generic board or
driver model.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
2014-04-20 13:16:43 +02:00
Paul Burton
5f978d7efe MIPS: Malta: convert to generic board
This patch converts the MIPS Malta development board to make use of the
generic board code now that it is supported on MIPS.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2014-04-20 13:16:43 +02:00
Masahiro Yamada
36bf57b6fb arm: remove lubbock board support
Enough time has passed since this board was moved to Orphan. Remove.

 - Remove board/lubbock/*
 - Remove include/configs/lubbock.h
 - Cleanup defined(CONFIG_LUBBOCK)
 - Move the entry from boards.cfg to doc/README.scrapyard

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-04-18 10:42:30 -04:00
Masahiro Yamada
bb3aef9caa powerpc: remove EVB64260 board support
Enough time has passed since this board was moved to Orphan. Remove.

 - Remove include/configs/EVB64260.h
 - Remove the entry from boards.cfg

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-04-18 10:42:30 -04:00
Masahiro Yamada
03f2ecc2cb powerpc: remove MOUSSE board support
Enough time has passed since this board was moved to Orphan. Remove.

 - Remove board/mousse/*
 - Remove include/configs/MOUSSE.h
 - Clean-up defined(CONFIG_MOUSSE)
 - Move the entry from boards.cfg to doc/README.scrapyard

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-04-18 10:42:30 -04:00
Masahiro Yamada
8b043e6dc2 powerpc: remove rsdproto board support
Enough time has passed since this board was moved to Orphan. Remove.

 - Remove board/rsdproto/*
 - Remove include/configs/rsdproto.h
 - Move the entry from boards.cfg to doc/README.scrapyard

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-04-18 10:42:30 -04:00
Masahiro Yamada
0ebf5f5c12 powerpc: remove RPXsuper board support
Enough time has passed since this board was moved to Orphan. Remove.

 - Remove board/rpxsuper/*
 - Remove include/configs/RPXsuper.h
 - Move the entry from boards.cfg to doc/README.scrapyard

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-04-18 10:42:30 -04:00
Masahiro Yamada
4fb3925ff8 powerpc: remove RPXClassic, RPXlite boards support
Enough time has passed since these boards were moved to Orphan. Remove.

 - Remove board/RPXlite/*
 - Remove board/RPXClassic/*
 - Remove include/configs/RPXlite.h
 - Remove include/configs/RPXClassic.h
 - Clean-up defined(CONFIG_RPXCLASSIC)
 - Move the entry from boards.cfg to doc/README.scrapyard

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-04-18 10:42:30 -04:00
Masahiro Yamada
aa6e1e45cf powerpc: remove ADS860, FADS823, FADS850SAR, FADS860T support
Enough time has passed since these boards were moved to Orphan. Remove.

 - Remove include/configs/{ADS860.h,FADS823.h,FADS850SAR.h,FADS860T.h}
 - Cleanup defined(CONFIG_ADS), defined(CONFIG_MPC823FADS),
   defined(CONFIG_MPC850SAR), defined(CONFIG_SYS_DAUGHTERBOARD)
 - Remove the entries from boards.cfg

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-04-18 10:42:29 -04:00
Masahiro Yamada
b8a49bdaaa powerpc: remove genietv board support
Enough time has passed since this board was moved to Orphan. Remove.

 - Remove board/genietv/*
 - Remove include/configs/GENIETV.h
 - Clean-up if defined(CONFIG_GENIETV)
 - Move the entry from boards.cfg to doc/README.scrapyard

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-04-18 10:42:29 -04:00
Masahiro Yamada
d6b11fd1f0 powerpc: remove MBX and MBX860T boards support
Enough time has passed since these boards were moved to Orphan. Remove.

 - Remove board/mbx8xx/*
 - Remove include/configs/{MBX.h,MBX860T.h}
 - Clean-up if defined(CONFIG_MBX)
 - Move the entries from boards.cfg to doc/README.scrapyard

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-04-18 10:42:29 -04:00
Masahiro Yamada
a146e8b189 powerpc: remove NX823 board support
Enough time has passed since this board was moved to Orphan. Remove.

 - Remove board/nx823/*
 - Remove include/configs/NX823.h
 - Clean-up ifdef(CONFIG_NX823)
 - Move the entry from boards.cfg to doc/README.scrapyard

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-04-18 10:42:29 -04:00
Tom Rini
2e8f5dc16a am43xx_evm: Drop SPI SPL
QSPI booting on this board does not use SPL, so drop SPI-SPL related
options.

Signed-off-by: Tom Rini <trini@ti.com>
2014-04-17 17:40:15 -04:00
Nishanth Menon
161d2d5ea8 omap3: zoom1: switch to generic ti_omap3_common config header
ti_omap3_common contains a lot of common header definitions that help
reduce the size of the zoom1 config file. So, use the generic header
and customize as needed for the platform (example: no spl).

Signed-off-by: Nishanth Menon <nm@ti.com>
2014-04-17 17:24:40 -04:00
Nishanth Menon
ea467c73ed omap3: zoom1: fix default console
We do not use ttyS2 anymore in Linux, it changed to ttyO2 a few years
back. never too late to update.

Signed-off-by: Nishanth Menon <nm@ti.com>
2014-04-17 17:24:40 -04:00
Nishanth Menon
c2e7c7b2d9 omap3: zoom1: enable bootz
Boot from zImage and fdt_file if uImage is not available to maintain
the legacy behavior.

Signed-off-by: Nishanth Menon <nm@ti.com>
2014-04-17 17:24:39 -04:00
Nishanth Menon
4e8183b7d4 omap3: zoom1: disable JFFS2 and enable FS_GENERIC
This is more in line with commits
664979a2a9f764b63b8094458b87247d254b0cc1(omap3_beagle: remove JFFS2
support.) and 102ce9ea7a (omap3_beagle:
enable CMD_FS_GENERIC and simplify load of image/ramdisk)

CMD_FS_GENERIC allows us to simplify where we load up our image from
either from ext2/fat etc. So, lets use that instead of cumbersome
options we'd have to use. Sticking with existing conventions,
defaults will be:
bootfile=uImage
bootpart=0:1 (first partition)
bootdir=/ (/ in first partition)

Signed-off-by: Nishanth Menon <nm@ti.com>
2014-04-17 17:24:39 -04:00
Nishanth Menon
d71dd0428c omap3: zoom1: enable common network commands
Basic networking commands for usability.

Signed-off-by: Nishanth Menon <nm@ti.com>
2014-04-17 17:24:39 -04:00
Nishanth Menon
9d70e77285 OMAP3: zoom1: enable LAN9211
Zoom1 was wrongly setup for LAN91C96. Fix it by enabling
LAN9211.

Signed-off-by: Nishanth Menon <nm@ti.com>
2014-04-17 17:24:39 -04:00
Nishanth Menon
ae3248a3fd omap3: zoom1: enable CONFIG_SYS_GENERIC_BOARD
CONFIG_SYS_GENERIC_BOARD should now be enabled for generic
functionality Further information in doc/README.generic-board

Signed-off-by: Nishanth Menon <nm@ti.com>
2014-04-17 17:24:39 -04:00
Karicheri, Muralidharan
fc9a8e8d40 keystone2: net: add keystone ethernet driver
Ethernet driver configures the CPSW, SGMI and Phy and uses
the the Navigator APIs. The driver supports 4 Ethernet ports and
can work with only one port at a time.

Port configurations are defined in board.c.

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
2014-04-17 17:24:39 -04:00
Karicheri, Muralidharan
56f624d06a k2hk-evm: add configuration for spi1 and spi2 support
currently only spi0 is enabled on k2hk evm. This
configuration update is needed to enable spi1 and spi2.

Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Tom Rini <trini@ti.com>
2014-04-17 17:24:39 -04:00
Vitaly Andrianov
ef509b9063 k2hk: add support for k2hk SOC and EVM
k2hk EVM is based on Texas Instruments Keystone2 Hawking/Kepler
SoC. Keystone2 SoC has ARM v7 Cortex-A15 MPCore processor. Please
refer the ti/k2hk_evm/README for details on the board, build and other
information.

This patch add support for keystone architecture and k2hk evm.

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Sandeep Nair <sandeep_n@ti.com>
2014-04-17 17:24:38 -04:00
Vitaly Andrianov
e8459dcc33 i2c, davinci: convert driver to new mutlibus/mutliadapter framework
- add davinci driver to new multibus/multiadpater support
    - adapted all config files, which uses this driver

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Heiko Schocher <hs@denx.de>
2014-04-17 17:24:38 -04:00
Tom Rini
df4dbb5df6 TI:omap3: Convert omap3_beagle to ti_omap3_common.h
Convert to using the common config files.  This requires a little more
flexibility in the common files than we had been using before.

Signed-off-by: Tom Rini <trini@ti.com>
2014-04-17 17:24:38 -04:00
Tom Rini
0dd54619ca TI:armv7: Switch to CONFIG_SYS_BOARD_GENERIC
Tested on AM335x GP EVM, AM335x EVM SK, Beaglebone White, Beaglebone
Black, AM437xx GP EVM, OMAP5 uEVM, OMAP4 Pandaboard

Signed-off-by: Tom Rini <trini@ti.com>
2014-04-17 17:24:38 -04:00
Tom Rini
79b079f35c dra7xx_evm: Add QSPI_4 support, qspiboot build target
We previously only supported QSPI_1 (single) support.  Add QSPI_4 (quad)
read support as well.  This means we can be given one of two boot device
values, but don't care which it is, so perform a fixup on the QSPI_4
value.  We add a qspiboot build target to better show how you would use
QSPI as a boot device in deployment.  When we boot from QSPI, we can
check the environment for 'boot_os' to control Falcon Mode.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2014-04-17 17:24:37 -04:00
Tom Rini
585d8bc116 am335x_evm: Drop SPI SPL support from the default build
This is only useful with the _spiboot build target anyhow, so only
include it then.  Drop CONFIG_SPL_OS_BOOT support then as the flash is
small and didn't include a spot for the device tree already.

Signed-off-by: Tom Rini <trini@ti.com>
2014-04-17 17:23:25 -04:00
Tom Rini
d3289aac64 TI:armv7: Change Falcon Mode DT load address
In general, we want to load the DT at base+128MB, so that we ahve
sufficient room for the kernel and a larger device tree.  In the case of
OMAP3, use 64MB instead as we have a number of boards with 128MB DDR.

Signed-off-by: Tom Rini <trini@ti.com>
2014-04-17 17:20:15 -04:00
Tom Rini
2737f0112b TI:omap5: Move CONFIG_ENV_SIZE to board config files
The size of the environment depends on the backing store, move this to
the board config files.

Signed-off-by: Tom Rini <trini@ti.com>
2014-04-17 14:39:54 -04:00
Tom Rini
bea0fd5e6a am43xx_evm: Update the ramdisk args, we pass things in just fine via DT
Signed-off-by: Tom Rini <trini@ti.com>
2014-04-17 14:39:54 -04:00
Tom Rini
18e44ce3f8 am335x_evm: Update the ramdisk args, we pass things in just fine via DT
Signed-off-by: Tom Rini <trini@ti.com>
2014-04-17 14:39:54 -04:00
Tom Rini
fb3ad9bd92 TI: Add, use a DEFAULT_LINUX_BOOT_ENV environment string
To deal with a reoccurring problem properly we need to specify addresses
for the Linux kernel, Flatted Device Tree and ramdisk that obey the
constraints within the kernel's Documentation/arm/Booting file but also
make sure that we relocate things within a valid address range.

It is possible with these addresses to also set fdt_high and initrd_high
to the value of 0xffffffff.  We don't do this by default to allow for
the most likely success of people using custom addresses however.

Signed-off-by: Tom Rini <trini@ti.com>
2014-04-17 14:39:54 -04:00
Tom Rini
6dd3b56689 mtd: Add a CONFIG_SPL_MTD_SUPPORT for a more full NAND subsystem in SPL
This mainly converts the am335x_spl_bch driver to the "normal" format
which means a slight change to nand_info within the driver.

Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Tom Rini <trini@ti.com>
2014-04-17 14:39:54 -04:00
Tom Rini
0f507779ca Merge branch 'next' 2014-04-17 14:33:25 -04:00
Stephen Warren
e04bfdacb3 ARM: tegra: add Jetson TK1 board
Jetson TK1 is an NVIDIA Tegra124 reference board, which shares much of
its design with Venice2.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-04-17 08:41:06 -07:00
Eric Benard
3cbeb0f004 RiOTboard and MarSBoard: add new boards support
RiOTboard is produced by Embest/Element 14 and is based on i.MX6 Solo
The following features are tested :
- UART2 (console)
- eMMC
- SDCard
- uSDCard
- Ethernet
- USB Host (through 4 ports hub)
- HDMI output
- I2C 1/2/3
- LVDS TFT with LCD8000-97C from Embest/Element 14

Boot on eMMC and through USB loader are tested.

For more informations on this board : http://www.riotboard.org/

MarSBoard is produced by Embest/Element 14 and is based on i.MX6 Dual
The following features are tested :
- UART2 (console)
- eMMC
- uSDCard
- Ethernet
- USB Host (through 2 ports hub)
- HDMI output
- I2C 1/2
- SPI NOR Flash
- LVDS TFT with LCD8000-97C from Embest/Element 14

Boot on SPI NOR and through USB loader are tested.

For more informations on this board :
http://www.embest-tech.com/shop/star/marsboard.html

Both boards are supported by the same code base as they are based on a
common trunk of schematics.

Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2014-04-15 12:23:57 +02:00
Eric Benard
053b795e30 mx6sabresd: use common board_video_skip
Signed-off-by: Eric Bénard <eric@eukrea.com>
2014-04-15 12:23:56 +02:00
Eric Benard
a47e449513 nitrogen6x: use common board_video_skip
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-04-15 12:23:56 +02:00
Tetsuyuki Kobayashi
fc56da0b2f arm: kzm9g: Add CONFIG_SYS_GENERIC_BOARD
Add CONFIG_SYS_GENERIC_BOARD to use common/board_[fr].c for kzm9g.

Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-04-14 17:42:30 +09:00
Andreas Bießmann
1b82491ee6 board:tricorder: fixup SPL OOB layout
Commit d016dc42ce changed the layout of BCH8 SW
on omap3 boards. We need to adopt the ecc layout for the nand_spl_simle
driver to avoid wrong ecc errors.

Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
Cc: Thomas Weber <thomas.weber@corscience.de>

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-04-11 10:08:42 -04:00
Andreas Bießmann
2347534450 board:tricorder: enable omap_gpio clocks
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
Cc: Thomas Weber <thomas.weber@corscience.de>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-04-11 10:08:42 -04:00
Albert ARIBAUD
519fdde9e6 Merge branch 'u-boot/master' into 'u-boot-arm/master'
Conflicts:
	arch/arm/cpu/arm926ejs/mxs/Makefile
	include/configs/trats.h
	include/configs/trats2.h
	include/mmc.h
2014-04-08 09:25:08 +02:00
David Feng
c71645ad2b arm64 patch: gicv3 support
This patch add gicv3 support to uboot armv8 platform.

Changes for v2:
  - rename arm/cpu/armv8/gic.S with arm/lib/gic_64.S
  - move smp_kick_all_cpus() from gic.S to start.S, it would be
    implementation dependent.
  - Each core initialize it's own ReDistributor instead of master
    initializeing all ReDistributors. This is advised by arnab.basu
    <arnab.basu@freescale.com>.

Signed-off-by: David Feng <fenghua@phytium.com.cn>
2014-04-08 00:15:12 +02:00
Albert ARIBAUD
284bb60ed6 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2014-04-07 19:13:42 +02:00
Nitin Garg
68659d649d MX6: Enable ARM errata workaround 794072 and 761320
Since MX6 is Cortex-A9 r2p10, enable software workaround
for errata 794072 and 761320.

Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
2014-04-07 18:11:01 +02:00
Chin Liang See
ddfeb0aaf4 socfpga: Adding Clock Manager driver
Clock Manager driver will be called to reconfigure all the
clocks setting based on user input. The input are passed to
Preloader through handoff files

Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
CC: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
2014-04-07 10:41:50 +02:00
Stefano Babic
1cad23c5f4 Merge branch 'master' of git://git.denx.de/u-boot-arm into master
Conflicts:
	arch/arm/cpu/arm926ejs/mxs/mxsimage.mx23.cfg
	arch/arm/cpu/arm926ejs/mxs/mxsimage.mx28.cfg

Signed-off-by: Stefano Babic <sbabic@denx.de>
2014-04-04 11:35:30 +02:00
Przemyslaw Marczak
aafd2c5ddb trats/trats2: enable CONFIG_RANDOM_UUID
This change enables automatically uuid generation by command gpt.
In case of updating partitions layout user don't need to care about
generate uuid manually.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Piotr Wilczek <p.wilczek@samsung.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: trini@ti.com
2014-04-02 16:36:06 -04:00
Łukasz Majewski
00b132bf34 config:trats2: Change u-boot's TEXT_BASE from 0x78100000 to 0x43e00000
The u-boot's image TEXT_BASE needs to be changed to 0x43e00000 from 0x78100000.

This change provides compatibility with other trats2 (RD_PQ) devices
(http://download.tizen.org/releases/system/).

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-04-02 21:00:04 +09:00
Stefano Babic
fa9c021632 mx6: add example DTB for mx6qsabreauto
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
2014-04-02 10:46:21 +02:00
Marek Vasut
97334c6616 arm: mx5: Avoid hardcoding memory sizes on M53EVK
The DRAM size can be easily detected at runtime on i.MX53. Implement
such detection on M53EVK and adjust the rest of the macros accordingly
to use the detected values.

An important thing to note here is that we had to override the function
for trimming the effective DRAM address, get_effective_memsize(). That
is because the function uses CONFIG_MAX_MEM_MAPPED as the upper bound of
the available DRAM and we don't have gd->bd->bi_dram[0].size set up at
the time the function is called, thus we cannot put this into the macro
CONFIG_MAX_MEM_MAPPED . Instead, we use custom override where we use the
size of the first DRAM block which we just detected.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
2014-03-31 18:28:51 +02:00
Marek Vasut
2f844e76da arm: mx5: Fix memory slowness on M53EVK
Fix memory access slowness on i.MX53 M53EVK board. Let us inspect the
issue: First of all, the i.MX53 CPU has two memory banks mapped at
0x7000_0000 and 0xb000_0000 and each of those can hold up to 1GiB of
DRAM memory. Notice that the memory area is not continuous. On M53EVK,
each of the banks contain 512MiB of DRAM, which makes a total of 1GiB
of memory available to the system.

The problem is how the relocation of U-Boot is treated on i.MX53 . The
U-Boot is placed at the ((start of first DRAM partition) + (gd->ram_size)) .
This in turn poses a problem, since in our case, the gd->ram_size is 1GiB,
the first DRAM bank starts at 0x7000_0000 and contains 512MiB of memory.
Thus, with this algorithm, U-Boot is placed at offset:

    0x7000_0000 + 1GiB - sizeof(u-boot and some small margin)

This is past the DRAM available in the first bank on M53EVK, but is still
within the address range of the first DRAM bank. Because of the memory
wrap-around, the data can still be read and written to this area, but the
access is much slower.

There were two ideas how to solve this problem, first was to map both of
the available DRAM chunks next to one another by using MMU, second was to
define CONFIG_VERY_BIG_RAM and CONFIG_MAX_MEM_MAPPED to size of the memory
in the first DRAM bank. We choose the later because it turns out the former
is not applicable afterall. The former cannot be used in case Linux kernel
was loaded into the second DRAM bank area, which would be remapped and one
would try booting the kernel, since at some point before the kernel is started,
the MMU would be turned off, which would destroy the mapping and hang the
system.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
2014-03-31 18:28:51 +02:00
Marek Vasut
31c832f93c arm: mx5: Avoid hardcoding memory sizes on MX53QSB
The DRAM size can be easily detected at runtime on i.MX53. Implement
such detection on MX53QSB and adjust the rest of the macros accordingly
to use the detected values.

An important thing to note here is that we had to override the function
for trimming the effective DRAM address, get_effective_memsize(). That
is because the function uses CONFIG_MAX_MEM_MAPPED as the upper bound of
the available DRAM and we don't have gd->bd->bi_dram[0].size set up at
the time the function is called, thus we cannot put this into the macro
CONFIG_MAX_MEM_MAPPED . Instead, we use custom override where we use the
size of the first DRAM block which we just detected.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
2014-03-31 18:28:51 +02:00
Marek Vasut
f79a023f41 arm: mx5: Fix memory slowness on MX53QSB
Fix memory access slowness on i.MX53 MX53QSB board. Let us inspect the
issue: First of all, the i.MX53 CPU has two memory banks mapped at
0x7000_0000 and 0xb000_0000 and each of those can hold up to 1GiB of
DRAM memory. Notice that the memory area is not continuous. On MX53QSB,
each of the banks contain 512MiB of DRAM, which makes a total of 1GiB
of memory available to the system.

The problem is how the relocation of U-Boot is treated on i.MX53 . The
U-Boot is placed at the ((start of first DRAM partition) + (gd->ram_size)) .
This in turn poses a problem, since in our case, the gd->ram_size is 1GiB,
the first DRAM bank starts at 0x7000_0000 and contains 512MiB of memory.
Thus, with this algorithm, U-Boot is placed at offset:

    0x7000_0000 + 1GiB - sizeof(u-boot and some small margin)

This is past the DRAM available in the first bank on MX53QSB, but is still
within the address range of the first DRAM bank. Because of the memory
wrap-around, the data can still be read and written to this area, but the
access is much slower.

There were two ideas how to solve this problem, first was to map both of
the available DRAM chunks next to one another by using MMU, second was to
define CONFIG_VERY_BIG_RAM and CONFIG_MAX_MEM_MAPPED to size of the memory
in the first DRAM bank. We choose the later because it turns out the former
is not applicable afterall. The former cannot be used in case Linux kernel
was loaded into the second DRAM bank area, which would be remapped and one
would try booting the kernel, since at some point before the kernel is started,
the MMU would be turned off, which would destroy the mapping and hang the
system.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
2014-03-31 18:28:51 +02:00
Marek Vasut
e919aa23ef ARM: mx6: Add PCIe on SabreSDP
Add support for PCIe on MX6 SabreSDP board and enable the support
in the config file.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Liu Ying <Ying.Liu@freescale.com>
2014-03-31 18:28:50 +02:00
Eric Nelson
ed2f0e1ffa ARM: mx6: Disable PCIe on SABRE Lite/Nitrogen6x
Use of PCIe on SABRE Lite and Nitrogen6x boards
is atypical and requires the use of custom daughter
boards.

Use in U-Boot is even rarer, so this patch removes it from
the standard configuration.

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
2014-03-31 18:28:50 +02:00
Fabio Estevam
3e94380b75 woodburn_sd: Remove CONFIG_BOOT_INTERNAL
CONFIG_BOOT_INTERNAL is not used anywhere, so let's remove it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2014-03-31 18:28:50 +02:00
Marek Vasut
2bbcccf552 ARM: mxs: Add OCOTP driver
Add yet another OCOTP driver for this i.MX family. This time, it's a driver for
the OCOTP variant found in the i.MX23 and i.MX28. This version of OCOTP is too
different from the i.MX6 one that I could not use the mxc_ocotp.c driver without
making it into a big pile of #ifdef . This driver implements the regular fuse
command interface, but due to the IP blocks' limitation, we support only READ
and PROG functions.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2014-03-31 18:28:50 +02:00
Marek Vasut
9c2c8a3129 arm: mxs: Adjust the load address of U-Boot and SPL for HAB
When using HAB, there are additional special requirements on the placement of
U-Boot and the U-Boot SPL in memory. To fullfill these, this patch moves the
U-Boot binary a little further from the begining of the DRAM, so the HAB CST
and IVT can be placed in front of the U-Boot binary. This is necessary, since
both the U-Boot and the IVT must be contained in single CST signature. To
make things worse, the IVT must be concatenated with one more entry at it's
end, that is the length of the entire CST signature, IVT and U-Boot binary
in memory. By placing the blocks in this order -- CST, IVT, U-Boot, we can
easily align them all and then produce the length field as needed.

As for the SPL, on i.MX23/i.MX28, the SPL size is limited to 32 KiB, thus
we place the IVT at 0x8000 offset, CST right past IVT and claim the size
is correct. The HAB library accepts this setup.

Finally, to make sure the vectoring in SPL still works even after moving
the SPL from 0x0 to 0x1000, we add a small function which copies the
vectoring code and tables to 0x0. This is fine, since the vectoring code
is position independent.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2014-03-31 18:28:50 +02:00
Hannes Petermaier
96de041ed9 board: enable 32kHz RTC OSC at B&R boards
Since RTC-Clock is needed on all B&R boards, the OSC will be enabled
wihtin SPL-stage.

Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
2014-03-31 11:19:41 -04:00
Tom Rini
423ec7fed2 am335x_evm: Drop CONFIG_SPL_ETH_SUPPORT from default build
On the boards this target supports this option is either non possible
without hardware mods (Beaglebone White/Black) or not supported due to
board design.  Drop this and regain some space.

Signed-off-by: Tom Rini <trini@ti.com>
2014-03-28 15:15:12 -04:00
Przemyslaw Marczak
e0021706f6 trats/trats2: enable exynos ace sha subsystem and hardware based lib rand
This allows to use exynos random number generator by enabling configs:
- CONFIG_EXYNOS_ACE_SHA
- CONFIG_LIB_HW_RAND

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
cc: Piotr Wilczek <p.wilczek@samsung.com>
cc: Minkyu Kang <mk7.kang@samsung.com>
2014-03-28 15:06:31 -04:00
Przemyslaw Marczak
3c1c68cc03 lib: rand: introduce new configs: CONFIG_LIB_RAND and CONFIG_LIB_HW_RAND
New configs:
- CONFIG_LIB_RAND    - to enable implementation of rand library in lib/rand.c
- CONFIG_LIB_HW_RAND - to enable hardware based implementations of lib rand

Other changes:
- add CONFIG_LIB_RAND to boards configs which needs rand()
- put only one rand.o dependency in lib/Makefile

CONFIG_LIB_HW_RAND should be defined for drivers which implements rand library
(declared in include/common.h):
- void srand(unsigned int seed)
- unsigned int rand(void)
- unsigned int rand_r(unsigned int *seedp)

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Michael Walle <michael@walle.cc>
Cc: Tom Rini <trini@ti.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-03-28 15:06:31 -04:00
Tom Rini
81b196bed8 Merge branch 'master' of git://git.denx.de/u-boot-usb 2014-03-28 08:19:05 -04:00
Albert ARIBAUD
ab6423cae0 Merge branch 'u-boot/master' into 'u-boot-arm/master'
Trivial merge conflict, needed to manually remove
local_info as per commit 41364f0f.

Conflicts:
	board/samsung/common/board.c
2014-03-25 10:53:15 +01:00
Heiko Schocher
401341d621 am335x, dfu: add DFU_MANIFEST_POLL_TIMEOUT to the siemens boards
as the siemens boards use dfu for updating a nand ubi partition
add DFU_MANIFEST_POLL_TIMEOUT to them, so dfu host waits after
complete transfer of the new image for DFU_MANIFEST_POLL_TIMEOUT
ms before sending again an usb request. So the board have enough
time to erase rest of the nand sectors.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-03-23 02:20:10 +01:00
Patrice Bouchand
def23217e4 sandbox: Enable CONFIG_CMD_LZMADEC in sandbox.h
As Simon Glass requested it, here's a patch that enables
CONFIG_CMD_LZMADEC in sandbox.

Signed-off-by: Patrice Bouchand <pbfwdlist@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
2014-03-22 14:47:30 -06:00
Masahiro Yamada
ece0d37014 sparc: consolidate CONFIG_{LEON, LEON2, LEON3} definition
CONFIG_LEON is already defined in
arch/sparc/cpu/{leon2,leon3}/config.mk.
Remove the redundant definition in board header files.

All leon3 boards define CONFIG_LEON3 in board header files.
Move the definition to arch/sparc/cpu/leon3/config.mk.

CONFIG_LEON2 can be move to arch/sparc/cpu/leon2/config.mk
as well.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Daniel Hellstrom <daniel@gaisler.com>
2014-03-21 16:44:10 -04:00
Simon Glass
2c072c958b sandbox: config: Enable cros_ec emulation and related items
Enable the Chrome OS EC emulation for sandbox along with LCD, sound
expanded GPIOs and a few other options to make this work correctly.

Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
2014-03-17 20:05:50 -06:00
Simon Glass
a77bf70978 sound: Move Samsung-specific code into its own file
The i2s code is in fact Samsung-specific, but there might be other
implementation. Move this code into its own file. This makes it slightly
more obviously how to adjust the code to support another SoC, when someone
takes this task on.

Also drop non-FDT support, since it isn't used on Exynos 5.

Tested-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
2014-03-17 20:05:49 -06:00
Simon Glass
9f6044256e sandbox: Increase memory size to 32MB
The current 4MB size is a little small for some tests, so increase it.

Reviewed-by: Hung-ying Tyan <tyanh@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
2014-03-17 20:05:45 -06:00
Albert ARIBAUD
63f347ec4c Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master' 2014-03-13 18:32:26 +01:00
Albert ARIBAUD
08798026f2 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2014-03-13 17:43:35 +01:00
Przemyslaw Marczak
18f3e0eb4f Trats/Trats2: Update Tizen partitions layout and dfu entities
Changes:
- update partitions layout
- update dfu entities
to be consistent with Tizen images for trats/trats2

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Łukasz Majewski <l.majewski@samsung.com>
cc: Piotr Wilczek <p.wilczek@samsung.com>
cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-03-13 10:30:56 +09:00
Masahiro Yamada
4ab3fc5eba kirkwood: kwbimage: refactor CONFIG_SYS_KWD_CONFIG
Pull out "$(SRCTREE)/" from CONFIG_SYS_KWD_CONFIG
and push it into the top Makefile.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Michael Walle <michael@walle.cc>
Cc: Simon Guinot <simon.guinot@sequanux.org>
Cc: Dave Purdy <david.c.purdy@gmail.com>
Cc: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Cc: Luka Perkov <luka@openwrt.org>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Jason Cooper <u-boot@lakedaemon.net>
Cc: Siddarth Gore <gores@marvell.com>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Eric Cooper <ecc@cmu.edu>
Cc: Suriyan Ramasami <suriyan.r@gmail.com>
2014-03-12 17:04:52 -04:00
Masahiro Yamada
e4536f8e37 freescale: pblimage: refactor CONFIG_SYS_FSL_PBL_{PBI, RCW}
Pull out "$(SRCTREE)/" from CONFIG_SYS_FSL_PBL_PBI
and CONFIG_SYS_FSL_PBL_RCW and push it into the top Makefile.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-03-12 17:04:49 -04:00
Gerhard Sittig
9a6a109f07 at91: enable USB ethernet for taskit stamp9g20
enabling CONFIG_MACB makes other locations in the stamp config file
enable network related commands (actually prevents disabling them)

enable USB ethernet support by activating generic support as well as
Asix and Moschip ethernet adapters

Signed-off-by: Gerhard Sittig <gsi@denx.de>
Acked-by: Andreas Bießman <andreas.devel@googlemail.com>
2014-03-12 17:04:34 -04:00
Gerhard Sittig
a743415f12 tegra: imx: omap: enable Moschip USB ethernet support for several boards
enable support for the Moschip USB ethernet adapter for those boards
which previously had support for "all other" USB ethernet adapters
(that's Asix _and_ SMSC) enabled -- which applies to harmony, m53evk,
mx53loco, nitrogen6x, omap3_beagle

Signed-off-by: Gerhard Sittig <gsi@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
2014-03-12 17:04:34 -04:00
Gerhard Sittig
eddf6d2868 tegra: omap: alpha-sort USB ethernet items for Asix and SMSC
adjust the harmony and omap3_beagle board configs to make
their CONFIG_USB_ETHER_* items appear in alphabetical order

Signed-off-by: Gerhard Sittig <gsi@denx.de>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
2014-03-12 17:04:32 -04:00
Stefan Roese
7bb6e29bff arm: omap: cm_t35: Fix: Re-add GPMC_NAND_ECC_LP_x8_LAYOUT
Patch a7e36fc9 (mtd: nand: omap: remove unused #defines from common
omap_gpmc.h) removed some MTD related defines. Including
GPMC_NAND_ECC_LP_x8_LAYOUT. But this define is also needed for the
memory controller configuration (only the x8 defines are needed,
the x16 defines are the default). Without it the NAND subsystem is
not configured correctly and booting into U-Boot does not work.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pekon Gupta <pekon@ti.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2014-03-12 16:22:12 -04:00
Tom Rini
e317675417 am335x_evm: Remove SPI SPL from NOR support target
When using the am335x_evm_nor target one is generally expecting to be
used in an environment when you want to program the NOR and not a
"deployment" type target.  In addition this only supports the Beaglebone
White with the memory cape and NOR module installed, which precludes the
presence of SPI flash.  Drop SPI as we were getting close to the binary
limit in some cases and slightly over with other toolchains.

Signed-off-by: Tom Rini <trini@ti.com>
2014-03-12 16:22:12 -04:00
Piotr Wilczek
1ecab0f30f board:trats2: Enable device tree on Trats2
This patch enables to run Trats2 board on device tree.

Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-03-12 19:55:00 +09:00
Piotr Wilczek
fe60164792 board:trats: Enable device tree on Trats
This patch enables to run Trats board on device tree.

Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-03-12 19:55:00 +09:00
Piotr Wilczek
3f41ffe4b5 board:universal: Enable device tree on Universal
This patch enables to run Universal board on device tree.

Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-03-12 19:55:00 +09:00
Piotr Wilczek
bf7716d6a3 board:origen: Enable device tree on Origen
This patch enables to run Origen board on device tree.

Uart, DRAM and MMC init functions are removed as their
generic replacements form the common board file are used.

The config file is modified to contain only board specific options.

Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Chander Kashyap <k.chander@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-03-12 19:55:00 +09:00
Piotr Wilczek
8e5e1e6a92 arm:exynos: add common DTS file for exynos 4
This patch adds common dtsi file and config header for all
Exynos 4 based boards.

Patch additionaly adds board specific (weak) functions for
board_early_init_f and board_power_init functions.

Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-03-12 19:54:59 +09:00
Fabio Estevam
81a1d6173c mx25pdk: Align the environment with other FSL boards
Allow the boot of a device tree mainline kernel by aligning the environment
variables with other FSL boards.

Tested NFS boot of a dt 3.14-rc5 kernel.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
2014-03-12 11:19:23 +01:00
Tim Harvey
59189a8b26 ventana: Add Gateworks Ventana family support
Gateworks Ventana is a product family based on the i.MX6.  This
patch adds support for all boards in the Ventana family. Where
possible, data from the boards EEPROM is used to determine various
details about the board at runtime.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2014-03-12 10:23:03 +01:00
Tom Rini
5495dae7aa Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-03-10 14:22:54 -04:00
Masahiro Yamada
ba650e9b52 m68k: Remove M5271EVB and idmr board support
CONFIG_SYS_HZ must be always 1000, but M5271EVB.h defines it
as 1000000 and idmr.h defines it as (50000000 / 64).

When compiling these two boards, a warning message is displayed:

  time.c:14:2: warning: #warning "CONFIG_SYS_HZ must be 1000
  and should not be defined by platforms" [-Wcpp]

There are no board maintainers for them so this commit just
deletes them.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Jason Jin <Jason.jin@freescale.com>
2014-03-10 11:38:13 -04:00
Bo Shen
27019e4a94 arm: atmel: sama5d3: add nand spl boot support
Add NAND SPL boot support with hardware PMECC.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-03-09 19:19:13 +01:00
Bo Shen
8a45b0ba87 arm: atmel: sama5d3: add spi spl boot support
Add SPI SPL boot support for sama5d3xek board.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-03-09 19:18:33 +01:00
Bo Shen
7ca6f36325 ARM: atmel: add sama5d3 Xplained board support
Add sama5d3 Xplained board support which use Atmel SAMA5D36 SoC.
Now it supports boot from NAND flash and SD/MMC card.
Features support:
  - NAND flash
  - SD/MMC card
  - Two USB hosts
  - Ethernet (one GMAC, one EMAC)

Signed-off-by: Bo Shen <voice.shen@atmel.com>
[reorder boards.cfg]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-03-09 19:09:50 +01:00
Andreas Henriksson
81724e09a0 at91sam9263ek: add mmc support
Add support for using the Atmel MCI driver on at91sam9263ek.
This change is modeled after the existing at91sam9260ek support.

Please note that this hooks up slot1 (MCI1) for SD. Not both.

Tested with at91bootstrap and u-boot on dataflash in slot 0
and fat-formatted 8GB SDHC in slot 1 on first revision
at91sam9263ek (which must use dataflash in slot0 to boot).

CONFIG_ATMEL_MCI_PORTB not tested.

Signed-off-by: Andreas Henriksson <andreas.henriksson@endian.se>
[remove empty line]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-03-09 18:24:52 +01:00
Tom Rini
247161b816 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2014-03-07 20:54:22 -05:00
Priyanka Jain
96ac18c9cc powerpc/t104xrdb: Update DDR initialization related settings
Update following DDR related settings for T1040RDB, T1042RDB_PI
-Correct number of chip selects to two as t1040 supports
 two Chip selects.
-Update board_specific_parameters udimm structure with settings
 derived via calibration.
-Update ddr_raw_timing sructure corresponding to DIMM.
-Set ODT to off. Typically on FSL board, ODT is set to 75 ohm,
 but on T104xRDB, on setting this , DDR instability is observed.
 Board-level debugging is in progress.

Verified the updated settings to be working fine with dual-ranked
Micron, MT18KSF51272AZ-1G6 DIMM at data rate 1600MT/s.

Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
2014-03-07 14:53:48 -08:00
Priyanka Jain
337b0c52b3 powerpc/t1040qds: Add Video - HDMI support
T1040 has internal display interface unit (DIU) for driving video.
T1040QDS supports video mode via
-LCD using TI enconder
-HDMI type interface via HDMI encoder

Chrontel, CH7301C encoder which is I2C programmable is used as
HDMI connector on T1040QDS.
This patch add support to
-enable Video interface for T1040QDS
-route qixis multiplexing to enable DIU-HDMI interface on board
-program DIU pixel clock gerenartor for T1040
-program HDMI encoder via I2C on board

Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-03-07 14:53:40 -08:00
Shengzhou Liu
8d67c3685e powerpc/t2080rdb: Add T2080PCIe-RDB board support
T2080PCIe-RDB is a Freescale Reference Design Board that hosts the T2080 SoC.
It works in two mode: standalone mode and PCIe endpoint mode.

T2080PCIe-RDB Feature Overview
------------------------------
Processor:
 - T2080 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz
DDR Memory:
 - Single memory controller capable of supporting DDR3 and DDR3-LP devices
 - 72bit 4GB DDR3-LP SODIMM in slot
Ethernet interfaces:
 - Two 10M/100M/1G RGMII ports on-board
 - Two 10Gbps SFP+ ports on-board
 - Two 10Gbps Base-T ports on-board
Accelerator:
 - DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
SerDes 16 lanes configuration:
 - SerDes-1 Lane A-B: to two 10G XFI fiber (MAC9 & MAC10)
 - SerDes-1 Lane C-D: to two 10G Base-T (MAC1 & MAC2)
 - SerDes-1 Lane E-H: to PCIe Goldfinger (PCIe4 x4, Gen3)
 - SerDes-2 Lane A-D: to PCIe Slot (PCIe1 x4, Gen2)
 - SerDes-2 Lane E-F: to C293 secure co-processor (PCIe2 x2)
 - SerDes-2 Lane G-H: to SATA1 & SATA2
IFC/Local Bus:
 - NOR:  128MB 16-bit NOR flash
 - NAND: 512MB 8-bit NAND flash
 - CPLD: for system controlling with programable header on-board
eSPI:
 - 64MB N25Q512 SPI flash
USB:
 - Two USB2.0 ports with internal PHY (both Type-A)
PCIe:
 - One PCIe x4 gold-finger
 - One PCIe x4 connector
 - One PCIe x2 end-point device (C293 Crypto co-processor)
SATA:
 - Two SATA 2.0 ports on-board
SDHC:
 - support a TF-card on-board
I2C:
 - Four I2C controllers.
UART:
 - Dual 4-pins UART serial ports

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-03-07 14:53:13 -08:00
Shengzhou Liu
6b7679c8d2 powerpc/t208xqds: fixup for t208xqds
Change QIXIS timing parameter CONFIG_SYS_CS3_FTIM2 to 8 from 0.
Fix EMI2 for t2080qds, which was caused by adding t2081qds.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-03-07 14:52:41 -08:00
Masahiro Yamada
58dac32764 powerpc: mpc8260: consolidate CONFIG_MPC8260 and CONFIG_8260
Before this commit, CONFIG_MPC8260 and CONFIG_8260
were used mixed-up.

All boards with mpc8260 cpu defined both of them:
  - CONFIG_MPC8260 was defined in board config headers
      and include/common.h
  - CONFIG_8260 was defined arch/powerpc/cpu/mpc8260/config.mk

We do not need to have both of them.
This commit keeps only CONFIG_MPC8260.

This commit does:
 - Delete CONFIG_8260 and CONFIG_MPC8260 definition
   in config headers and include/common.h
 - Rename CONFIG_8260 to CONFIG_MPC8260
    in arch/powerpc/cpu/mpc8260/config.mk.
 - Rename #ifdef CONFIG_8260 to #ifdef CONFIG_MPC8260

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
2014-03-07 10:59:06 -05:00
Masahiro Yamada
cfda6bd2d8 mips: move CONFIG_MIPS{32, 64} definition to config.mk
All mips32 boards define CONFIG_MIPS32 in config headers
except malta boards which define it in boards.cfg.
We can consolidate them by defining it in
arch/mips/cpu/mips32/config.mk.

CONFIG_MIPS64 definition can be moved to
arch/mips/cpu/mips64/config.mk as well.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2014-03-07 10:59:06 -05:00
Masahiro Yamada
cd2e46cb38 kbuild: add CONFIG_ prefix to USE_PRIVATE_LIBGCC
Before this commit, USE_PRIVATE_LIBGCC was defined in
arch-specific config.mk and referenced in
arch/$(ARCH)/lib/Makefile.

We are not happy about parsing config.mk again and again.
We have to keep the same behavior with a different way.

By adding "CONFIG_" prefix, this macro appears
in include/autoconf.mk, include/spl-autoconf.mk.
(And treating USE_PRIVATE_LIBGCC as CONFIG macro
is reasonable enough.)

Tegra SoC family defined USE_PRIVATE_LIBGCC as "yes"
in arch/arm/cpu/arm720t/tegra*/config.mk,
whereas did not define it in arch/arm/cpu/armv7/tegra*/config.mk.

It means Tegra enables PRIVATE_LIBGCC only for SPL.
We can describe the same behavior by adding

  #ifdef CONFIG_SPL_BUILD
  # define CONFIG_USE_PRIVATE_LIBGCC
  #endif

to include/configs/tegra-common.h.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
2014-03-07 10:59:06 -05:00
Masahiro Yamada
e91df49fbb kbuild, blackfin: Add CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED
Many (but not all) of Blackfin boards give -O2 option
to compile under lib/ directory.
That means lib/ should be speed-optimized,
whereas other parts should be size-optimized.

We want to keep the same behavior,
but do not want to parse board/*/config.mk again and again.
We've got no choice but to invent a new method.

CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED, if it is enabled,
gives -O2 flag only for building under lib/ directory.

Dirty codes which I had marked as "FIX ME"
in board/${BOARD}/config.mk have been deleted.
Instead, CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED has been
defined in include/configs/${BOARD}.h.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
2014-03-07 10:59:06 -05:00
Stefan Roese
345b77baca ppc4xx: Remove 4xx NAND booting support
As ppc4xx currently only supports the deprecated nand_spl infrastructure
and nobody seems to have time / resources to port this over to the newer
SPL infrastructure, lets remove NAND booting completely.

This should not affect the "normal", non NAND-booting ppc4xx platforms
that are currently supported.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Tirumala Marri <tmarri@apm.com>
Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Tested-by: Matthias Fuchs <matthias.fuchs@esd.eu>
2014-03-07 10:59:06 -05:00
Albert ARIBAUD
de4fdfc1f2 Merge branch 'u-boot-tegra/master' into 'u-boot-arm/master' 2014-03-07 14:32:42 +01:00
Enric Balletbo i Serra
dd1e8583ee OMAP3: igep00x0: Enable required clocks for GPIO that are used.
Enable required clocks for GPIO to fix a boot issue introduced by commit
f33b9bd398 (arm: omap3: Enable clocks for
peripherals only if they are used).

Without this patch the u-boot freezes after the following messages

  OMAP36XX/37XX-GP ES1.2, CPU-OPP2, L3-200MHz, Max CPU Clock 1 Ghz
  IGEPv2 + LPDDR/NAND
  I2C:   ready
  DRAM:  512 MiB
  NAND:  512 MiB
  MMC:   OMAP SD/MMC: 0

Diving into the issue, the sequence that produces the u-boot freezes is

  setup_net_chip
   |--> gpio_direction_out
         |--> _set_gpio_dataout
               |--> __raw_writel

To avoid this we just need enable the clocks for GPIOs that are used, but it
would be interesting implement a mechanism to protect these situations and
make sure that the clock is enabled when we request a GPIO.

Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
2014-03-06 11:21:37 -05:00
Stephen Warren
f940c72e16 ARM: tegra: implement bootcmd_pxe
This retrieves a PXE config file over the network, and executes it. This
allows an extlinux config file  to be retrieved over the network and
executed, whereas the existing bootcmd_dhcp retrieves a U-Boot script.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-03-05 16:59:08 -07:00
Stephen Warren
4d7d2e570a ARM: tegra: rework boot scripts
Update the common Tegra boot scripts in the default environment to

a) Make use of the new "test -e" shell command to avoid some error
   messages.

b) Allow booting using the sysboot command and extlinux.conf. This
   allows easy creation of boot menus, and provides a simple interface
   for distros to parameterize/configure the boot process.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-03-05 16:59:08 -07:00
Stephen Warren
68cf64db1d ARM: tegra: convert tegra to use distro defaults
Modify all Tegra boards to include the "distro defaults" header, so that
all the config options distros expect are enabled. Remove any #defines
that enable the same options from the Tegra files.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-03-05 16:59:08 -07:00
Stephen Warren
f75dc784fc ARM: tegra: set CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS
Tegra's EHCI controllers only have a single PORTSC register. Configure
U-Boot to know this. This prevents e.g. ehci_shutdown() from touching
non-existent registers.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-03-05 16:59:08 -07:00
Stephen Warren
cd7efc2a94 ARM: tegra: move CONFIG_TEGRAnn
<asm/arch-tegra/tegra.h> needs to use CONFIG_TEGRA* to conditionalize
some definitions, since some modules moved between generations. Move
the definition of CONFIG_TEGRAnn to a header that's included earlier,
so that it's set by the time tegra.h needs to use it.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-03-05 16:59:07 -07:00
Tom Rini
e4b87e5b1d Merge branch 'master' of git://git.denx.de/u-boot-nand-flash 2014-03-04 21:23:42 -05:00
pekon gupta
a7e36fc95f mtd: nand: omap: remove unused #defines from common omap_gpmc.h
OMAP NAND driver can detect Page-size and OOB-size of NAND device from ONFI
params or nand_id[] table. And based on that it defines ECC layout.
This patch
1) removes following board configs used for defining NAND ECC layout
	- GPMC_NAND_ECC_LP_x16_LAYOUT (for large page x16 NAND)
	- GPMC_NAND_ECC_LP_x8_LAYOUT  (for large page x8 NAND)
	- GPMC_NAND_ECC_SP_x16_LAYOUT (for small page x16 NAND)
	- GPMC_NAND_ECC_SP_x8_LAYOUT  (for small page x8 NAND)

2) removes unused #defines in common omap_gpmc.h depending on above configs

Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-03-04 17:23:54 -06:00
Simon Glass
e2d8a714a7 sandbox: Convert GPIOs to use driver model
Convert sandbox over to use driver model GPIOs.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-03-04 12:15:30 -05:00
Simon Glass
39f7611fec dm: Add a demonstration/example driver
As an example of how to write a uclass and a driver, provide a demo version
of each, accessible through the 'demo' command.

To use these with driver model, define CONFIG_CMD_DEMO and CONFIG_DM_DEMO.

The two demo drivers are enabled with CONFIG_DM_DEMO_SIMPLE and
CONFIG_DM_DEMO_SHAPE.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Signed-off-by: Viktor Křivák <viktor.krivak@gmail.com>
Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
2014-03-04 12:15:29 -05:00
Simon Glass
0681195977 dm: Add a 'dm' command for testing
This command is not required for driver model operation, but can be useful
for testing. It provides simple dumps of internal data structures.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Signed-off-by: Viktor Křivák <viktor.krivak@gmail.com>
Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
2014-03-04 12:15:29 -05:00
Simon Glass
2e7d35d2a6 dm: Add basic tests
Add some tests of driver model functionality. Coverage includes:

- basic init
- binding of drivers to devices using platform_data
- automatic probing of devices when referenced
- availability of platform data to devices
- lifecycle from bind to probe to remove to unbind
- renumbering within a uclass when devices are probed/removed
- calling driver-defined operations
- deactivation of drivers when removed
- memory leak across creation and destruction of drivers/uclasses
- uclass init/destroy methods
- automatic probe/remove of children/parents when needed

This function is enabled for sandbox, using CONFIG_DM_TEST.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-03-04 12:15:29 -05:00
Simon Glass
653ef91cba sandbox: config: Enable driver model
Use driver model in sandbox to permit running of driver model unit test.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-03-04 12:15:29 -05:00
Simon Glass
714a5621c2 sandbox: Build a device tree file for sandbox
Add support for building a device tree for sandbox's CONFIG_OF_HOSTFILE
option to make it easier to use device tree with sandbox.

This adjusts the Makefile to build a u-boot.dtb file which can be passed
to sandbox U-Boot with:

   ./u-boot -d u-boot.dtb

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-03-04 12:15:28 -05:00
Alexey Brodkin
1ace402239 sizes.h - consolidate for all architectures
Copied from Linux sources "include/linux/sizes.h" commit
413541dd66d51f791a0b169d9b9014e4f56be13c

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
[trini: Add bcm Kona platforms to the patch]
Signed-off-by: Tom Rini <trini@ti.com>
2014-03-04 12:15:01 -05:00
Stefan Roese
cc07294bc7 arm: am335x: DXR2: Reset SMSC LAN9303 switch via GPIO upon bootup
Since the switch may be re-configured for VLAN usage in Linux (or any
other OS), lets reset the switch to its default register values upon
power-up. Otherwise network might not be available in U-Boot.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Lukas Stockmann <lukas.stockmann@siemens.com>
Cc: Tom Rini <trini@ti.com>
2014-03-04 09:42:07 -05:00
Mugunthan V N
3a3939bf3d ARM: AM43xx: Add Ethernet boot support to SPL
Add Ethernet Boot support to SPL

Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2014-03-04 09:42:07 -05:00
Mugunthan V N
a35ad51efe ARM: AM335x: add support for reading cpsw 2nd mac address from efuse
Adding support for reading cpsw 2nd mac address from efuse and pass it
to kernel via dtb which will be used in dual emac mode of cpsw.
Also adding mii command support to am335x common config.

Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2014-03-04 09:42:06 -05:00
Mugunthan V N
4cdd7fda91 ARM: AM43xx: Add CPSW support to AM43xx EPOS and GP EVM
Adding support for CPSW to AM43xx EPOS nad GP EVM which is connected
to RMII and RGMII phy respectively and enable cpsw in config.

Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2014-03-04 09:42:06 -05:00
Mugunthan V N
9c653aad16 drivers: net: cpsw: add support to have phy address from cpsw platform data
Some platforms like AM437x have different EVMs with different phy addresses,
so this patch adds support for passing phy address via cpsw plaform data.
Also renamed phy_id to phy_addr so better understanding of the code.

Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
[trini: Update BuR am335x_igep0033 pcm051_rev3 pcm051_rev1 cm_t335
pengwyn boards]
Signed-off-by: Tom Rini <trini@ti.com>
2014-03-04 09:41:53 -05:00
Michal Simek
7450a7f730 zynq: Do not use SPL OF initialization
Disable CONFIG_OF_CONTROL for SPL compilation.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-03-04 09:27:34 -05:00
Tom Rini
eeb72e6761 Merge branch 'master' of git://git.denx.de/u-boot-arm
Conflicts:
	arch/arm/cpu/armv7/config.mk
	board/ti/am43xx/mux.c
	include/configs/am43xx_evm.h

Signed-off-by: Tom Rini <trini@ti.com>
2014-02-26 16:49:58 -05:00
Tom Rini
a7e8c15f71 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
With this, fixup a trivial build error of get_effective_memsize needing
to be updated in the new board/freescale/p1010rdb/spl.c

Signed-off-by: Tom Rini <trini@ti.com>
2014-02-25 13:55:49 -05:00
Masahiro Yamada
4a377552f0 kbuild: Move linker sciript check to prepare1
Same as the previous commit.
Move sanity check to prepare1 target to avoid nasty troubles.

Before this commit, LDSCRIPT existence was not checked
when it was specified by CONFIG_SYS_LDSCRIPT.
Now LDSCRIPT existence is checked for all boards.

$(wildcard $(LDSCRIPT)) must point to the linker scripts
with absolute path.
Otherwise, make will terminate with a false error
on out-of-tree build.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-02-25 11:01:29 -05:00
Haijun.Zhang
c6e8f49a16 powerpc/mpc8536DS:Increase binary size for mpc8536DS board
u-boot binary size for Freescale mpc8536DS platforms is 512KB.
This has been reached to upper limit of the platforms and causig
linker error. So increase the u-boot binary size to 768KB.

Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-02-24 15:23:50 -08:00
Ying Zhang
c9e1f58818 powerpc: p1010rdb: Enable p1010rdb to start from NAND/SD/SPI flash with SPL
In the previous patches, we introduced the SPL/TPL fraamework.
For SD/SPI flash booting way, we introduce the SPL to enable a loader stub. The
SPL was loaded by the code from the internal on-chip ROM. The SPL initializes
the DDR according to the SPD and loads the final uboot image into DDR, then
jump to the DDR to begin execution.

For NAND booting way, the nand SPL has size limitation on some board(e.g.
P1010RDB), it can not be more than 8KB, we can call it "minimal SPL", So the
dynamic DDR driver doesn't fit into this minimum SPL. We added the TPL that is
loaded by the the minimal SPL. The TPL initializes the DDR according to the SPD
and loads the final uboot image into DDR,then jump to the DDR to begin execution.

This patch enabled SPL/TPL for P1010RDB to support starting from NAND/SD/SPI
flash with SPL framework and initializing the DDR according to SPD in the SPL/TPL.
Because the minimal SPL load the TPL to L2 SRAM and the jump to the L2 SRAM to
execute, so the section .resetvec is no longer needed.

Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-02-24 15:23:32 -08:00
Ying Zhang
27585bd357 SPL: P1022DS: fix the problem booting from spi flash
There was no enough memory for malloc in SPL booting from spi flash, so
relayout the memory in SPL: reduce the memory for global data from 16K
Bytes to 4K Bytes, save the space for malloc.

Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-02-24 15:23:25 -08:00
Ying Zhang
5a89fa927c SPL: P2020RDB: fix the problem booting from spi flash
There was no enough stack in SPL, so the buffer needed in SPL is to malloc
from memory pool and to repalce the temporary variable.

Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-02-24 15:23:19 -08:00
Ying Zhang
ee4d65117d SPL: powerpc: expand SPL's length to 128K
1. The SPL's length of SDCARD boot has not enough,expand the SPL's
length to 128K.
2. deleted unused symbol: CONFIG_SYS_RUN_INDDR

Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-02-24 15:23:11 -08:00
Shengzhou Liu
254887a57e powerpc/t2081qds: Add T2081 QDS board support
T2081 QDS is a high-performance computing evaluation, development and
test platform supporting the T2081 QorIQ Power Architecture processor.

T2081QDS board Overview
-----------------------
- T2081 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz
- 2MB shared L2 and 512KB L3 CoreNet platform cache (CPC)
- CoreNet fabric supporting coherent and noncoherent transactions with
  prioritization and bandwidth allocation
- 32-/64-bit DDR3/DDR3LP SDRAM memory controller with ECC and interleaving
- Ethernet interfaces:
  - Two on-board 10M/100M/1G bps RGMII ports
  - Two 10Gbps XFI with on-board SFP+ cage
  - 1Gbps/2.5Gbps SGMII Riser card
  - 10Gbps XAUI Riser card
- Accelerator:
  - DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
- SerDes:
  - 8 lanes up to 10.3125GHz
  - Supports SGMII, HiGig, XFI, XAUI and Aurora debug,
- IFC:
  - 512MB NOR Flash, 2GB NAND Flash, PromJet debug port and Qixis FPGA
- eSPI:
  - Three SPI flash (16MB N25Q128A + 16MB EN25S64 + 512KB SST25WF040)
- USB:
  - Two USB2.0 ports with internal PHY (one Type-A + one micro Type mini-AB)
- PCIe:
  - Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV)
- eSDHC:
  - Supports various SD/SDHC/SDXC/eMMC devices with adapter cards and
    voltage translators
- I2C:
  - Four I2C controllers.
- UART:
  - Dual 4-pins UART serial ports

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-02-24 15:23:01 -08:00
Masahiro Yamada
f55e911ff4 arm: delete unused macro CONFIG_ARCH_DEVICE_TREE
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Rajeshwari Birje <rajeshwari.s@samsung.com>
Cc: Inderpal Singh <inderpal.singh@linaro.org>
2014-02-24 10:56:33 -05:00
Albert ARIBAUD
fae56934a0 Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2014-02-24 10:29:59 +01:00
Darwin Rambo
9ed679aeeb board: bcm28155_ap: Add board files
Add support for the bcm28155_ap reference board.

Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Tim Kryger <tkryger@linaro.org>
2014-02-22 19:30:45 +01:00
Stephen Warren
1998a1a6c3 ARM: rpi_b: rework boot scripts, enable sysboot
Rework rpi_b's bootcmd (and sub-commands) to match Tegra's bootcmd as
much as possible. This will aid in a future patch which will create a
common header e.g. config_distro_bootcmd.h.

While at it, enable booting from extlinux.conf using the sysboot command.

The iteration and componentization currently makes a little more sense
for Tegra than RPi, but I'd still like to keep the two as similar as
possible. USB and networking support is coming to the RPi in due course,
and it'll all make more sense then anyway.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2014-02-22 14:06:51 +01:00
Nishanth Menon
4f80d5ba8e omap4_common: config: remove I2C for SPL mode
Commit 6789e84eca (i2c, omap24xx:
convert driver to new mutlibus/mutliadapter framework) intended to
make I2C driver compatible with latest changes. It unfortunately has
had a impact on size on SPL as well. For example on SDP4430,
32032 bytes before/MLO
35416 bytes after/MLO

With this mentioned commit, MLO stops booting on SDP4430 as only 32K
is accessible for non-secure (bootloader) s/w on GP devices and the size
increase to 56K fails boot.

On the latest u-boot commit e7be18225f,
MLO is now at size 35592 bytes, However, I2C is not necessary for SPL
to function as we use SR_I2C for controlling the PMIC.
Disabling I2C reduces MLO to 32224 bytes which allows
OMAP4 GP platform to boot up.

Since this is common for all OMAP4 platforms, remove the need for I2C
for SPL builds in the common config.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Sricharan R <r.sricharan@ti.com>
2014-02-21 14:03:44 -05:00
Tom Rini
2efa79ae00 dra7xx_evm: Enable GPT commands
Signed-off-by: Tom Rini <trini@ti.com>
2014-02-21 14:03:44 -05:00
Tom Rini
0f1b044395 am43xx_evm: Enable GPT commands
Signed-off-by: Tom Rini <trini@ti.com>
2014-02-21 14:03:44 -05:00
Tom Rini
01d92b0472 am335x_evm: Enable GPT commands
Signed-off-by: Tom Rini <trini@ti.com>
2014-02-21 14:03:27 -05:00
Stefan Roese
bc97f48915 arm: omap: cm_t35: Remove CONFIG_SYS_BOOTMAPSZ to fix FDT Linux booting
With CONFIG_SYS_BOOTMAPSZ defined, recent Linux kernel booting
results in this error:

   Booting using the fdt blob at 0x81f00000
   Loading Kernel Image ... OK
ERROR: Failed to allocate 0x1189d bytes below 0x80004000.
device tree - allocation error
FDT creation failed! hanging...### ERROR ### Please RESET the board ###

Removing this define solves this issue.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@ti.com>
2014-02-21 13:55:41 -05:00
Stefano Babic
a5d64dbf20 OMAP3: fix default environment for mcx board
Patch allows to load a script at the startup from MMC.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2014-02-21 13:55:41 -05:00
Stefano Babic
9267110270 OMAP3: add missing gpio clock init and fix NAND SPL for mcx board
Patch contains the same fixes as commit
4b9b2c300a
(missing CONFIG_OMAP3_GPIO_2) and commit
f9095aac793aa8917ab9b915c5d449e6dc8d3d30 (missing CONFIG_SPL_NAND_SOFTECC).
Same issues are relevant for the mcx board, too.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2014-02-21 13:55:41 -05:00
Stefan Roese
36481ded99 arm: omap3: Fix tao3530/omap3_ha SPL boot hangup (GPIO clocks not enabled)
Patch f33b9bd3
[arm: omap3: Enable clocks for peripherals only if they are used]
breaks SPL booting on tao3530. Since some gpio input's are
read to detect the board revision. But with this patch above, the
clocks to the GPIO subsystems are not enabled per default any more.
The GPIO banks need to be configured specifically now.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2014-02-21 13:55:40 -05:00
Hannes Petermaier
072cefe07d Add support for B&R KWB Motherboard
Adds support for Bernecker & Rainer Industrieelektronik GmbH KWB
Motherboard, using TI's AM3352 SoC.

Most of code is derived from TI's AM335x_EVM

Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Cc: trini@ti.com
2014-02-21 13:55:40 -05:00
Hannes Petermaier
893c04e17c board: Add support for B&R T-Series Motherboard
Adds support for Bernecker & Rainer Industrieelektronik GmbH T-Series
Motherboard, using TI's AM3352 SoC.

Most of code is derived from TI's AM335x_EVM

Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
2014-02-21 13:55:40 -05:00
Lothar Felten
da4105dfcd am335x: Initial support for Silica Pengwyn board
This patch add support for the Silica Pengwyn board [1]
The board is based on a TI AM3354 CPU [2]
All jumpers removed it will boot from the SDcard, the console is on
UART1 accessible via the FDTI -> USB. The on board NAND flash is
supported and can act as boot medium, depending on jumper settings.
USB Host, USB Device and Ethernet are also provided but untested.

[1]
http://www.silica.com/product/silica-pengwyn-board.html
[2]
http://www.ti.com/product/am3354

Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
[trini: Move CONFIG_BOARD_LATE_INIT into am335x_evm.h, drop unused
spi0_pin_mux from Pengwyn support]
Signed-off-by: Tom Rini <trini@ti.com>
2014-02-21 13:54:57 -05:00
Stephen Warren
5c92d4823d ARM: rpi_b: load /uEnv.txt from MMC at startup
The Pi has no flash to store an environment in the usual fashion. However,
the user may wish to customize the environment. We know that the SD card
must be present, since that's where the boot ROM has loaded U-Boot from.
So, load uEnv.txt from there early during boot. This allows the user to
e.g. customize boot_targets, in order to automatically select network
boot.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2014-02-21 15:30:18 +01:00
Stephen Warren
29235b7337 ARM: rpi_b: convert to use distro defaults
Modify the rpi_b board to include the "distro defaults" header, so that
all the config options distros expect are enabled. Remove any #defines
that enable the same options from the rpi_b.h.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2014-02-21 15:30:15 +01:00
Tom Rini
4c89a369c7 Merge branch 'master' of git://git.denx.de/u-boot-spi 2014-02-21 08:00:22 -05:00
Alexey Brodkin
c42eb7f2c7 axs101: change command prompt marker to match marketing name of the board
Proper spelling of the boad marketing name is with upper case.
So changing it from lower case to upper case here.

Cc: Tom Rini <trini@ti.com>

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2014-02-21 07:54:05 -05:00
Tom Rini
6853e6aa77 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-02-20 12:18:59 -05:00
Albert ARIBAUD
3e11350255 Merge branch 'u-boot/master' into 'u-boot-arm/master'
Conflicts:
	Makefile
	drivers/net/npe/Makefile

These two conflicts arise from commit 0b2d3f20
("ARM: NET: Remove the IXP NPE ethernet driver") and are
resolved by deleting the drivers/net/npe/Makefile file
and removing the CONFIG_IXP4XX_NPE line from Makefile.
2014-02-20 13:16:05 +01:00
Alexey Brodkin
f93f589ca2 spear: move CONFIG_SYS_I2C_BASE from arch-spear/hardware to board configs
Having CONFIG_SYS_I2C_BASE requires DW I2C driver to explicitly include
<arch/hardware.h> which other platforms may not have at all.

It's always good to have a driver platform-independent.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

Cc: Tom Rini <trini@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Armando Visconti <armando.visconti@st.com>
2014-02-20 06:49:02 +01:00
Michael Burr
18948632a9 i2c: zynq: Add support for the second i2c controller
Initialize the second i2c controller.

Signed-off-by: Michael Burr <michael.burr@logicpd.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-20 06:46:55 +01:00
Masahiro Yamada
2f13363b09 configs: Delete unused CONFIG_SYS_64BIT_{VSPRINTF, STRTOUL}
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-02-19 11:10:05 -05:00
Masahiro Yamada
627b73e2a7 configs: Delete obsolete macro, CONFIG_SYS_GBL_DATA_SIZE
CONFIG_SYS_GBL_DATA_SIZE is not used any more.
The size of struct "global_data" is automatically calculated
by asm-offsets. (See lib/asm-offsets.c)

GENERATED_GBL_DATA_SIZE should be used instead of
CONFIG_SYS_GBL_DATA_SIZE.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-02-19 11:10:05 -05:00
Masahiro Yamada
df2f6c9621 config: remove platform CONFIG_SYS_HZ definition part 3
This commit removes platform CONFIG_SYS_HZ definition for the
remainders of part1 (commit cdb23792) and part2 (commit f232950f).

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Rob Herring <rob.herring@calxeda.com>
2014-02-19 10:46:26 -05:00
Masahiro Yamada
0a4bce32d6 mini2440.h: Delete remainder of dead board
Commit af5b9b1f removed mini2440 board support,
but missed to delete include/configs/mini2440.h.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-02-19 10:46:25 -05:00
Stephen Warren
89ba42d183 sandbox: enable CONFIG_CMD_FS_GENERIC
Since the generic ls command no longer segfaults sandbox, enable it.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
2014-02-19 09:47:34 -05:00
Albert ARIBAUD
e7538fee99 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2014-02-19 12:04:45 +01:00
Michal Simek
d7e269cfbd zynq: Add support for U-BOOT SPL
SPL is using ps7_init.c/h files which are generated
from design tools which have to be copied to
boards/xilinx/zynq folder before compilation.

BSS section is moved to SDRAM because fat support
requires more space than SRAM size.

Added:
- MMC and QSPI support
- Boot OS directly from SPL
- Enable SPL command

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
2014-02-19 09:41:22 +01:00
Soren Brinkmann
d6c9bbaad1 zynq: Implement dump clock command
Enable and implement dump clock command which shows
soc frequencies.

Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19 09:41:22 +01:00
Soren Brinkmann
6c3e61de3c zynq: Provide a framework to read clock frequencies
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19 09:41:21 +01:00
Michal Simek
bf83495040 zynq: serial: Simplify serial driver initialization
Define both serial uarts in the driver and return
default uart based on board configuration.

- Move baseaddresses to hardware.h
- Define default baudrate and clock values

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19 09:41:21 +01:00
Michal Simek
427b2d4e5a zynq: Enable tftp put command
For saving content of memory via tftp to file.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19 09:41:21 +01:00
Michal Simek
ae9f489977 zynq: Extend kernel image size to 20MB
Extend max kernel image size. Gunzip is checking
this value. If kernel is larger, message below is shown.

Uncompressing Kernel Image ... Error: inflate() returned -5
GUNZIP: uncompress, out-of-mem or overwrite error -
must RESET board to recover

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19 09:41:21 +01:00
Michal Simek
c74a94415c zynq: Fix incorrect header name
Zynq common configuration is placed in zynq-common.h
not zynq_common.h.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19 09:41:20 +01:00
Albert ARIBAUD
a87a0ce702 Merge branch 'u-boot-pxa/master' into 'u-boot-arm/master' 2014-02-19 07:15:01 +01:00
Sourav Poddar
ea4c7a8321 am437x_epos_evm: add SPL API, QSPI, and serial flash support
Enables support for SPI SPL, QSPI and Spansion serial flash device
on the EVM. Configures pin muxes for QSPI mode.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-02-18 22:41:09 +05:30
Tom Rini
c4d376fd1c Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-02-17 14:22:02 -05:00
Tom Rini
18c83588bc Merge branch 'master' of git://git.denx.de/u-boot-mmc 2014-02-17 14:16:08 -05:00
Gerlando Falauto
9c134e189a arm/km: introduce kmsugp1 target
KMSUGP1 is from a u-boot perspective (almost) identical to KMNUSA.
The only difference is that the PCIe reset is connected to Kirkwood pin
MPP7_PEX_RST_OUTn, we use a dedicated config flag KM_PCIE_RESET_MPP7.
Such pin should theoretically be handled by the PCIe subsystem
automatically, but this turned out not to be the case.
So simply configure this PIN as a GPIO and issue a pulse manually.

Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Karlheinz Jerg <karlheinz.jerg@keymile.com>
Cc: Valentin Longchamp <valenting.longchamp@keymile.com>
Cc: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-02-13 17:45:36 +01:00
Gerlando Falauto
b1c2a7ae32 arm/km: define fdt_high env variable and allow backwards compatibility
Add set_fdthigh subcommand to "subbootcmds" (release) so to set "fdt_high"
This is necessary on Kirkwood so that the FDT does not get relocated
above the memory limit that the kernel cannot access
(that is the memory part reserved for the switch).
This was tested on NUSA1, where it is necessary, and on ETER1, where it
doesn't seem to hurt.

We want the scripts to also work with older versions of u-boot, where:
a) set_fdthigh is not defined (will be default env for newer u-boots)
b) the fdt will not be available

For this reason, we use "set_fdthigh" to tell whether we are running
a newer (FDT-aware) u-boot or not.
So if "set_fdthigh" runs successfully or arch != arm we try loading
the fdt; otherwise we proceed normally.

Notice how, contrary to release mode, set_fdthigh will _not_ be part of
subbootcmds for develop and ramfs, but will be executed as part of
"tftpfdt".

Since this is only needed for kirkwood cards, and it prevents the kernel
from booting on QorIQ (though it seemed to work on ETER1), we change
its definition in the default env for powerpc so that the value is only
set on ARM.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-02-13 16:18:13 +01:00
Gerlando Falauto
7b2268b88f arm/km: enable FDT for km_kirwkood
This consists of:
a) Defining the addresses, enabling fdtsupport [arm]
b) Defining "cramfsloadfdt"  [arm,powerpc => common]
c) Adding the FDT address to bootm [arm,powerpc => common]
d) Defining "tftpfdt" in ramfs-,develop- [arm,powerpc >= common]

This should work with 3.10 kernels, whether loaded through TFTP
(with rootfs either through NFS or TFTP-ramfs) or from the NAND.

The machid was left unchanged, this should keep compatibility with both
older and newer kernels.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-02-13 16:17:54 +01:00
Holger Brunck
56cde17760 arm/km: add CONFIG_KM_BOARD_EXTRA_ENV to default environment
This is needed for board specific additional environment variables.
E.g. the mgcoge3un has this additional "waitforne" variable.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-02-13 16:17:16 +01:00
Holger Brunck
2a4ebef267 arm/km/suv31: switch to 256MB RAM
We now use 256MB RAM instead of 128MB. We can use the same config file
as kmnusa.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-02-13 16:16:56 +01:00
Michal Simek
38716189d4 zynq: Fix elf header generation
This patch is here because of:
"arm: keep all sections in ELF file"
(sha1: 47ed5dd031)

Our tools expect to have elf with only LOAD header.
Without this fix also PHDR, INTERP and DYNAMIC headers
are available in ELF.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-13 15:33:00 +01:00
Michal Simek
dfa94058f5 zynq: Use full tftpboot command instead of shortcut tftp
The reason is enabling tftpput command where
tftp shorcut stops to work for tftpboot.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-13 15:25:52 +01:00
Stephen Warren
bccaa476f6 ARM: rpi_b: set $fdtfile in default environment
U-Boot names the Raspberry Pi board rpi_b. This means that the common
expression for DTB filename ${soc}-${board}.dtb expands to
bcm2835-rpi_b.dtb. However, the DTB generated by the Linux kernel is
bcm2835-rpi-b.dtb. Set $fdtfile in U-Boot's environment so that scripts
look for the correct DTB filename.

An alternative would be to rename the U-Boot board to rpi-b. However,
that change would be far more invasive, and end up affecting users (i.e
they'd have to change their U-Boot build commands).

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2014-02-13 15:00:53 +01:00
Albert ARIBAUD
d53ccdb341 Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master' 2014-02-13 13:30:54 +01:00
Stefano Babic
17998eff90 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-02-11 12:55:32 +01:00
Fabio Estevam
6d73c23410 mx6: Enable L2 cache support
Add L2 cache support and enable it by default.

Configure the L2 cache in the same way as done by FSL kernel:
http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/tree/arch/arm/mach-mx6/mm.c?h=imx_3.0.35_4.1.0

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Dirk Behme <dirk.behme@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2014-02-11 11:24:12 +01:00
Fabio Estevam
6fc049bef6 mx6sl: Adjust fdt_addr to avoid address overlapping
Similarly as it was done on commit 6584a1b526 (ARM: mx6: Change the FDT loading
address to avoid overlaping), we need to adjust the fdt_addr in order to be
able to boot FSL 3.10 kernel.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2014-02-11 11:17:10 +01:00
Otavio Salvador
c0a5b0816f vf610twr: Set default environment to use zImage
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2014-02-11 11:04:41 +01:00
Otavio Salvador
5ef142498e udoo: Set default environment to use zImage
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2014-02-11 11:04:41 +01:00
Otavio Salvador
8e184a53b3 mx6slevk: Set default environment to use zImage
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2014-02-11 11:04:41 +01:00
Otavio Salvador
f2e4288acb mx6sabre_common: Set default environment to use zImage
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2014-02-11 11:04:41 +01:00
Otavio Salvador
124f196af2 mx6qarm2: Set default environment to use zImage
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2014-02-11 11:04:41 +01:00
Otavio Salvador
f28154b5b5 mx53loco: Set default environment to use zImage
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2014-02-11 11:04:41 +01:00
Otavio Salvador
20f233bb66 mx51evk: Set default environment to use zImage
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2014-02-11 11:04:40 +01:00
Otavio Salvador
fb3f917021 mx28evk: Set default environment to use zImage
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2014-02-11 11:04:40 +01:00
Otavio Salvador
04585b0638 mx23evk: Set default environment to use zImage
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2014-02-11 11:04:40 +01:00
Otavio Salvador
1e373dffa4 hummingboard: Set default environment to use zImage
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2014-02-11 11:04:40 +01:00
Otavio Salvador
4ac0c2bfba cgtqmx6eval: Set default environment to use zImage
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2014-02-11 11:04:40 +01:00
Tom Rini
b818d9ab8d dra7xx_evm: Add CONFIG_SUPPORT_EMMC_BOOT, document usage
Add a README to the board which lists the commands required to enable
booting from the eMMC boot partitions found on the board.

Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-02-07 18:17:49 +02:00
Tom Rini
378ec0f816 omap5_uevm: Add CONFIG_SUPPORT_EMMC_BOOT, document usage
Add a README to the board which lists the commands required to enable
booting from the eMMC boot partitions found on the board.

Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-02-07 18:17:49 +02:00
Tom Rini
1a78d28d02 x600: Switch to CONFIG_PHYLIB
Now that the designware ethernet driver uses phylib we need to turn it
on here.

Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
2014-02-07 09:18:35 -05:00
Alexey Brodkin
92a190aaab net/designware - switch driver to phylib usage
With this change driver will benefit from existing phylib and thus
custom phy functionality implemented in the driver will go away:
 * Instantiation of the driver is now much shorter - 2 parameters
instead of 4.
 * Simplified phy management/functoinality in driver is replaced with
rich functionality of phylib.
 * Support of custom phy initialization is now done with existing
"board_phy_config".

Note that after this change some previously used config options
(driver-specific PHY configuration) will be obsolete and they are simply
substituted with similar options of phylib.

For example:
 * CONFIG_DW_AUTONEG - no need in this one. Autonegotiation is enabled
by default.
 * CONFIG_DW_SEARCH_PHY - if one wants to specify attached phy
explicitly CONFIG_PHY_ADDR board config option has to be used, otherwise
automatically the first discovered on MDIO bus phy will be used

I believe there's no need now in "doc/README.designware_eth" because
user only needs to instantiate the driver with "designware_initialize"
whose prototype exists in "include/netdev.h".

Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2014-02-07 09:16:46 -05:00
Alexey Brodkin
a7069ddfa9 arc: add AXS101 board support
AXS101 is a new generation of devlopment boards from Synopsys that houses
ASIC with ARC700 and lots of DesignWare peripherals:

 * DW APB UART
 * DW Mobile Storage (MMC/SD)
 * DW I2C
 * DW GMAC

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Francois Bedard <fbedard@synopsys.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
2014-02-07 08:14:33 -05:00
Alexey Brodkin
66712b8b46 arc: add Arcangel4 board support
Arcangel4 is a FPGA-based development board that is used for prototyping and
verificationof of both ARC hardware (CPUs) and software running upon CPU.

This board avaialble in 2 flavours:
 * Little-endian (arcangel4)
 * Big-endian (arcangel4-be)

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Francois Bedard <fbedard@synopsys.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
2014-02-07 08:14:33 -05:00
Piotr Wilczek
425e26de29 board:samsung:trats/trats2: enable boot with appended and separated DTB
This patch modifies envs to enable dual kernel boot
 - with separated DTB if the DTB file is loaded successfully;
 - with DTB apppended to uImage if DTB file is not found;
This is neccesssary for backward compatibilty.

Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-07 10:06:24 +09:00
Piotr Wilczek
8c57fb7d9a board:samsung:trats2: add env variables describing platform
This patch adds variables describing platform (soc, board, vendor)
to default environment.

Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-07 10:06:24 +09:00
Piotr Wilczek
943eacde68 board:samsung:trats: add env variables describing platform
This patch adds variables describing platform (soc, board, vendor)
to default environment.

Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-07 10:06:24 +09:00
Piotr Wilczek
815a6072f0 board:samsung:universal: add env variables describing platform
This patch adds variables describing platform (soc, board, vendor)
to default environment.

Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-07 10:06:24 +09:00
Piotr Wilczek
2ac9a35bcd board:samsung:goni: add env variables describing platform
This patch adds variables describing platform (soc, board, vendor)
to default environment.

Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Mateusz Zalega <m.zalega@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-07 10:06:24 +09:00
Marek Vasut
f016f8ca3d usb: mv_udc: Rename to ci_udc
The mv_udc is not marvell-specific anymore. The mv_udc is used to drive
generic ChipIdea CI13xxx series OTG cores, so rename the driver to ci_udc
instead.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Stefano Babic <sbabic@denx.de>
2014-02-06 04:48:15 +01:00
Marek Vasut
e317de6b08 ARM: IXP: Remove dvl_host board
The board is unmaintained, just like the rest of the IXP.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michael Schwingen <michael@schwingen.org>
Cc: Tom Rini <trini@ti.com>
2014-02-06 02:51:52 +01:00
Marek Vasut
6ff7aafa4b ARM: IXP: Remove actux4 board
The board is unmaintained, just like the rest of the IXP.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michael Schwingen <michael@schwingen.org>
Cc: Tom Rini <trini@ti.com>
2014-02-06 02:51:51 +01:00
Marek Vasut
38da33f3c1 ARM: IXP: Remove actux3 board
The board is unmaintained, just like the rest of the IXP.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michael Schwingen <michael@schwingen.org>
Cc: Tom Rini <trini@ti.com>
2014-02-06 02:51:51 +01:00
Marek Vasut
13e0ee7f9a ARM: IXP: Remove actux2 board
The board is unmaintained, just like the rest of the IXP.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michael Schwingen <michael@schwingen.org>
Cc: Tom Rini <trini@ti.com>
2014-02-06 02:51:51 +01:00
Marek Vasut
373ee048a8 ARM: IXP: Remove actux1 board
The board is unmaintained, just like the rest of the IXP.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michael Schwingen <michael@schwingen.org>
Cc: Tom Rini <trini@ti.com>
2014-02-06 02:51:51 +01:00
Tom Rini
9c1d0e9f16 Merge branch 'master' of git://www.denx.de/git/u-boot-microblaze 2014-02-04 11:51:20 -05:00
Michal Simek
9d24274509 microblaze: Add SPL support
Add support for U-BOOT SPL. NOR and RAM mode are supported.
There are 3 images in NOR flash. u-boot.img, dtb and kernel.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-04 16:39:50 +01:00
Michal Simek
22ff7f4d19 microblaze: Enable buffer write for NOR flashes
It speeds up writing a lot.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-04 16:39:37 +01:00
Jim Lin
7bc5c8c930 ARM: tegra: fix "bootp" issue for Tegra124 too
Fix the timeout issue after running "bootp" command in U-Boot console.

TXFIFOTHRES bits of TXFILLTUNING register should be set to 0x10 after a
controller reset and before RUN bit is set (per technical reference
manual).

Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:47 -07:00
Tom Warren
f7dc4ac37c ARM: tegra: add Venice2 (Tegra124) board
These are the board files for Venice2 (Tegra124), plus the AS3722 PMIC
files. PMIC init will be moved to pmic_common_init later.

This builds/boots on Venice2, SPI/MMC/USB/I2C all work. Audio, display
and WB/LP0 are not supported yet.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:47 -07:00
Stephen Warren
09266b270f ARM: tegra: clear $usb_need_init each boot
$usb_need_init prevents "usb start" from being run multiple times for
each boot attempt, i.e. once for USB storage, another for PXE, and
another for DHCP. However, the flag that's used to determine when to run
"usb start" is never cleared, so a subsequent "boot" command will never
probe for a freshly plugged in USB device. Fix this so that new USB
devices will be probed once per boot attempt.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:44 -07:00
Stephen Warren
b9b53a60ae ARM: tegra: set env vars to indicate Cardhu A04 support
The U-Boot "cardhu" build supports only revision 4 of the Cardhu board
and later compatible revisions. Hence, set $board_name in the default
environment to "cardhu-a04" rather than just "cardhu".

The Linux kernel has separate DTs for Cardhu A02 and A04, although the
former isn't really supported any more. Consequently, the kernel DT file
that matches the U-Boot cardhu build is "tegra30-cardhu-a04.dtb" rather
than "tegra30-cardhu.dtb". Set the $fdtfile default environment variable
to reflect this.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:44 -07:00
Valentin Longchamp
47c1180c02 kmp204x: enable support for SPANSION SPI NOR
The new prototype and the final series was moved from Micron to Spansion
to have a better reset sequence that is easier to support.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-02-03 08:38:50 -08:00
Valentin Longchamp
cf7707a1df KM: add the KM_UBI_PART_BOOT_OPTS #define
This define can be used if the ubi boot partition (defined for all
Keymile boards with KM_UBI_PARTITION_NAME_BOOT #define to ubi0) needs
some additionnal boot options.

This is the case for the kmp204x boards since u-boot does not support
NAND Flash subpage accesses on this platform, an additionnal argument
that defines the VID offstet must be given to the kernel.

The UBI cmd line option now looks like this "ubi.mtd=ubi0,2048" on this
platform.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-02-03 08:38:50 -08:00
Valentin Longchamp
e95bbc8bac kmp204x: add support for the kmcoge4 board
The kmcoge4 board is the product board derived from the kmlion1
prototype. The main difference between the 2 boards is that the kmcoge4
does not configure the Local Bus controller for LCS2.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[York Sun: Minor change to boards.cfg to keep targets in order]
Signed-off-by: York Sun <yorksun@freescale.com>
2014-02-03 08:38:50 -08:00
Rainer Boschung
f3e74d0a9f kmp204x: I2C deblocking support
This patch adds support for using some GPIOs that are connected to the
I2C bus to force the bus lines state and perform some bus deblocking
sequences.

The KM common deblocking algorithm from board/keymile/common/common.c is
used. The GPIO lines used for deblocking the I2C bus are some external
GPIOs provided by the QRIO CPLD:
  - SCL = GPIOA_20
  - SDA = GPIOA_21

The QRIO GPIOs act in an open-drain-like manner, for 0 the line is
driven low and for 1 the GPIO is set as input and the line gets
pulled-up.

Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-02-03 08:38:50 -08:00
Rainer Boschung
dd21f09669 kmp204x: support for QRIO1 bootcounter
Make use of the QRIO1 32bit register at 0x20 as bootcounter register
Check for BOOTCOUNT_MAGIC pattern when before bootcounter value is read

Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[York Sun: Minor change to commit message]
Signed-off-by: York Sun <yorksun@freescale.com>
2014-02-03 08:38:49 -08:00
Priyanka Jain
714fd406da powerpc/t104xrdb: Add basic ethernet support
This covers only non-L2 switch ethernet interfaces i.e.
RGMII and SGMII interface for both T1040RDB and T1042RDB_PI

T1040RDB is configured as serdes protocol 0x66 which can
support following interfaces
    2 RGMIIS on DTSEC4, DTSEC5
    1 SGMII on DTSEC3

T1042RDB_PI is configured as serdes protocol 0x06 which can
support following interfaces
    2 RGMIIS on DTSEC4, DTSEC5

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
[York Sun: Minor change in commit message]
Signed-off-by: York Sun <yorksun@freescale.com>
2014-02-03 08:38:49 -08:00
Prabhakar Kushwaha
48aee3913d powerpc/t104xrdb: Update T1042RDB.h in config folder
Add usb2 node entry to hwconfig default

Remove DDR controller interleaving from hwconfig

Move SPI related macros out of "#ifdef CONFIG_SPIFLASH"

Add CONFIG_SYS_CSPR2_EXT to make CPLD accessible in u-boot

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Fix commit message]
Signed-off-by: York Sun <yorksun@freescale.com>
2014-02-03 08:38:49 -08:00
Priyanka Jain
9b444be322 powerpc/t104xrdb: Update T1040RDB.h in config folder
Add usb2 node entry in "hwconfig string"

Remove controller interleaving from hwconfig string as T1040
has only one DDR conroller

SPI related macros which were earlier under #ifdef CONFIG_SPIFLASH
are move outside so that they are defined for all cases as these
macros are also used by other u-boot code

Add CONFIG_SYS_CSPR2_EXT to make CPLD accessible

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
[York Sun: Minor change to commit message]
Signed-off-by: York Sun <yorksun@freescale.com>
2014-02-03 08:38:49 -08:00
Prabhakar Kushwaha
5b7672fc49 boards/t1040qds: Adds ethernet support for T1040
Enable entherent for T1040QDS. It enables FM1@DTSEC3, FM1@DTSEC4, FM1@DTSEC5
    Define MDIO related configs
    Added eth.c file
    Update t1040.c to support RGMII and SGMII
    Update t1040qds.c to support ethernet
    Define the PHY address

Signed-off-by: Arpit Goel <B44344@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: remove dash from commit message]
Signed-off-by: York Sun <yorksun@freescale.com>
2014-02-03 08:38:48 -08:00
Przemyslaw Marczak
a0afc6f378 config: trats: trats2: extend dfu_alt_info by env update settings
This change allows updating environment stored on MMC by dfu or thor.

New setting:
- "params.bin mmc 0x38 0x8"

File params.bin can be generated by: tools/mkenvimage.
e.g. ./mkenvimage -s 4096 -o params.bin <env_text_file>

Every new env variable in text file should start with a new line.

Sample env text file:
- board/samsung/common/dfu_sample_env.txt

Requirements:
- file name: "params.bin"
- file size: 4096 Bytes - the same as CONFIG_ENV_SIZE.
  Other size will cause CRC miscalculation at boot.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
CC: Piotr Wilczek <p.wilczek@samsung.com>
CC: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-03 16:09:10 +09:00
Przemyslaw Marczak
82b0a05561 universal: add LCD download menu support
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-03 15:36:14 +09:00
Przemyslaw Marczak
f64236a907 trats2: add LCD download menu support
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-03 15:36:14 +09:00
Przemyslaw Marczak
00e64ab647 trats: add LCD download menu support
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-03 15:36:14 +09:00
Przemyslaw Marczak
2df21cb3ea samsung: boards: update display configs with 16bpp mode.
16 bpp mode is required by LCD console mode.
This change updates exynos board files.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-03 15:36:14 +09:00
Przemyslaw Marczak
903afe18bb lib: tizen: change Tizen logo with the new one.
Changes:
- check image bpp instead of resolution when returns logo address
- remove 32bpp logo
- add 16bpp logo in two formats: bmp and gzipped bmp
- init logo address with "0" for unsupported bpp mode
- update boards configs with proper image size for gunzip
- extend structure vidinfo by two fields: logo_x_offset and logo_y_offset.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Tested-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-03 15:36:14 +09:00
Przemyslaw Marczak
679549d180 samsung: common: Add file for common functions, draw_logo() cleanup.
Changes:

new file:
- board/samsung/common/misc.c
  depends on: CONFIG_MISC_COMMON
- move draw_logo() to misc.c

configs: trats, trats2, universal:
- enable CONFIG_MISC_COMMON,
- enable CONFIG_MISC_INIT_R,
- add misc_init_r() and call draw_logo() in it.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-03 15:36:14 +09:00
Przemyslaw Marczak
8475c869c3 s5p: gpio: change gpio coding method for s5p gpio.
Old s5p gpio coding method was not clean and was not working properly
for all parts and banks. New method is clean and easy to extend.

Gpio coding mask:
0x000000ff - pin number
0x00ffff00 - bank offset
0xff000000 - part number

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-03 15:36:14 +09:00
Albert ARIBAUD
e97f9d817e Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2014-01-29 14:07:50 +01:00
Albert ARIBAUD
c0cae2e245 Merge branch 'u-boot-arm/next' into 'u-boot-arm/master' 2014-01-28 11:25:28 +01:00
Marek Vasut
9a12fcd0c9 ARM: m53evk: Enable CONFIG_REGEX
Enable CONFIG_REGEX on M53EVK to allow usage of regular expressions
on environment variables.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2014-01-26 15:24:43 +01:00
Marek Vasut
8331273ca9 ARM: m53evk: Rename mxc-nand to mxc_nand
The name the Linux kernel expects is 'mxc_nand' , not 'mxc-nand' .
This patch renames the driver name.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2014-01-26 15:24:39 +01:00
Marek Vasut
147f8fa3c5 ARM: mx6: Enable PCIe on Sabrelite
Enable PCI express on MX6 Sabrelite.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2014-01-26 12:41:20 +01:00
Dan Murphy
2b36fe579c arm: am43xx: Add USB spl boot support
Add the USB host boot support for the am43xx evm
Add the macros to boot from a usb drive in uBoot

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2014-01-24 16:59:22 -05:00
Masahiro Yamada
b2a6dfe4f8 powerpc: mpc5xxx: remove redundant CONFIG_MPC5xxx definition
We do not have to define CONFIG_MPC5xxx in board config headers
(and start.S) because it is defined in arch/powerpc/cpu/mpc5xxx/config.mk.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-01-24 16:59:21 -05:00
Masahiro Yamada
84acd1e179 powerpc: mpc86xx: move CONFIG_MPC86xx definition to CPU config.mk
Define CONFIG_MPC86xx in arch/powerpc/cpu/mpc86xx/config.mk
because all target boards with mpc86xx cpu define it.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-01-24 16:59:08 -05:00
Masahiro Yamada
d40ddae4b3 powerpc: mpc85xx: move CONFIG_MPC85xx definition to CPU config.mk
Define CONFIG_MPC85xx in arch/powerpc/cpu/mpc85xx/config.mk
because all target boards with mpc85xx cpu define it.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-01-24 16:59:08 -05:00
Masahiro Yamada
52de0e49df powerpc: mpc824x: remove redundant CONFIG_MPC824X definition
We do not have to define CONFIG_MPC824X in board config headers
because it is defined in arch/powerpc/cpu/mpc824x/config.mk.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-01-24 16:59:08 -05:00
Masahiro Yamada
bf7aac9726 powerpc: mpc512x: remove redundant CONFIG_MPC512X definition
We do not have to define CONFIG_MPC512X in board config headers
because it is defined in arch/powerpc/cpu/mpc512x/config.mk.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-01-24 16:59:08 -05:00
Masahiro Yamada
53a79fe3a2 powerpc: mpc83xx: remove redundant CONFIG_MPC83xx definition
We do not have to define CONFIG_MPC83xx in board config headers
because it is defined in arch/powerpc/cpu/mpc83xx/config.mk.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-01-24 16:59:08 -05:00
Masahiro Yamada
1a0afe1fad powerpc: ppc4xx: remove redundant CONFIG_4xx definition
We do not have to define CONFIG_4xx in board config headers
because it is defined in arch/powerpc/cpu/ppc4xx/config.mk.

include/configs/JSE.h defines "CONFIG_4x", not "CONFIG_4xx".
I believe it is a typo because "CONFIG_4x" is not used at all
in other files.
So, I also deleted "CONFIG_4x" in include/configs/JSE.h.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-01-24 16:59:07 -05:00
Masahiro Yamada
3b98b57fa7 include: delete unused header files
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-01-24 16:59:07 -05:00
Masahiro Yamada
5378d5eabe avr32: move CONFIG_AVR32 definition to arch/avr32/config.mk
Like other architectures, CONFIG_AVR32 can be defined
in arch/avr32/config.mk rather than board header files.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-01-24 16:59:07 -05:00
Tom Rini
b1cde7e21f am43xx_evm.h: Correct SPL max size
Upon further inspection of relevant parts of the architecture, the
maximum SPL binary size is 220KiB.

Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2014-01-24 11:41:17 -05:00
Enric Balletbò i Serra
e37e954eba OMAP3: igep00x0: Convert to ti_omap3_common.h.
To reduce code duplication update omap3_igep00x0.h to use ti_omap3_common.h.

Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
2014-01-24 11:38:39 -05:00
Enric Balletbò i Serra
c7964f86c2 TI: OMAP3: Create common config files for TI OMAP3 platforms.
Create a new file, include/configs/ti_omap3_common.h, for everything
common to the OMAP3 SoC leaving just the board specific part to board
configuration file.

Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
2014-01-24 11:38:39 -05:00
Enric Balletbò i Serra
c6a7fce113 TI: armv7: Do not define the number DRAM banks if is already defined.
If CONFIG_NR_DRAM_BANKS is not defined, we say (for simplicity) that we have
1 bank, but for some boards should be interesting that we can define
CONFIG_NR_DRAM_BANKS. To handle this possibility just define the number of
DRAM banks if is not already defined. This is useful for some OMAP3 boards
where the DRAM initialitzation is only at u-boot level.

Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
2014-01-24 11:38:39 -05:00
Enric Balletbò i Serra
70e71b61bc TI: armv7: Move ELM support to SoC configuration file.
The ELM hardware engine wihich is used for ECC error detections is not present
on OMAP3 SoC, so move the CONFIG_SPL_NAND_AM33XX_BCH from ti_armv7_common.h to
SoC configuration file.

Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Reviewed-by:  Lokesh Vutla <lokeshvutla@ti.com>
2014-01-24 11:38:39 -05:00
Enric Balletbò i Serra
3d657a05a9 ARM: OMAP5: Rename to ti_omap5_common.h
Follow the pattern ti_<processor family>_common.h used by other TI processors
to be coherent. So just rename omap5_common.h to ti_omap5_common.h.

Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Reviewed-by:  Lokesh Vutla <lokeshvutla@ti.com>
2014-01-24 11:38:39 -05:00
Enric Balletbò i Serra
6c0a032a32 ARM: OMAP4: Rename to ti_omap4_common.h
Follow the pattern ti_<processor family>_common.h used by other TI processors
to be coherent. So just rename omap4_common.h to ti_omap4_common.h.

Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Reviewed-by:  Lokesh Vutla <lokeshvutla@ti.com>
2014-01-24 11:38:39 -05:00
Haijun.Zhang
d47e3d2707 esdhc: Detecting 8 bit width before mmc initialization
The upper 4 data signals of esdhc are shared with spi flash.
So detect if the upper 4 pins are assigned to esdhc before
enable sdhc 8 bit width.

Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-01-22 08:56:34 -08:00
Haijun.Zhang
f7e27cc5ee esdhc: Workaround for card can't be detected on T4240QDS
Card detection pin is ineffective on T4240QDS Rev1.0.
There are two cards can be connected to board.
1. eMMC card is built-in board, can not be removed. so
   For eMMC card it is always there.
2. Card detecting pin is functional for SDHC card in Rev2.0.

This workaround force sdhc driver scan and initialize the card
regardless of whether the card is inserted or not in case Rev1.0.

Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-01-22 08:56:15 -08:00
Prabhakar Kushwaha
e222b1f36f powerpc/mpc85xx:Increase binary size for P, B & T series boards.
u-boot binary size for Freescale mpc85xx platforms is 512KB.
This has been reached to upper limit for some of the platforms causig
linker error.

So, Increase the u-boot binary size to 768KB.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
2014-01-21 14:06:30 -08:00
Prabhakar Kushwaha
690e425844 powerpc:Rename CONFIG_PBLRCW_CONFIG & CONFIG_SYS_FSL_PBL_PBI
Rename CONFIG_PBLRCW_CONFIG and CONFIG_PBLRCW_CONFIG.

Also add their details in README.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-01-21 14:02:41 -08:00
Po Liu
eb6b458cef powerpc/c29xpcie: 8k page size NAND boot support base on TPL/SPL
Using the TPL/SPL method to booting from 8k page NAND flash.
	- Add 256kB size SRAM tlb for second step booting;
	- Add spl.c for TPL image boot;
	- Add spl_minimal.c for minimal SPL image;
	- Add C29XPCIE_NAND configure;
	- Modify C29XPCIE.h for nand config and enviroment;

Signed-off-by: Po Liu <Po.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-01-21 13:42:40 -08:00
Priyanka Jain
2eb3ac7fe8 powerpc/t1040qds: Update DDR initialization related settings
Update following DDR related settings for T1040QDS
-Correct number of chip selects to two as t1040qds supports
 two Chip selects.
-Update board_specific_parameters udimm structure with settings
 derived via calibration.
-Reduced I2C speed to 50KHz as DDR-SPD does not get reliably
 read at 400KHz.

Verified the updated settings to be working fine with dual-ranked
Micron, MT18KSF51272AZ-1G6 DIMM at data rate 833MT/s, 1333MT/s and
1600MT/s.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-01-21 13:35:20 -08:00
Robert Nelson
5c9038b6af omap3_beagle: use omap3-beagle.dtb for the C4 revision
findftd is currently setting fdtfile to undefined for the beagle c4, select omap3-beagle.dtb instead

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
2014-01-17 11:03:04 -05:00
Bhupesh Sharma
3865ceb726 vexpress/armv8: Fix incorrect ethernet controller
This patch enables ethernet support in ARMv8 foundation model. The ARMv8
foundation model supports a SMSC91C111 integrated MAC and PHY module
which is present at base address 0x01A000000.

The previous implementation had enabled SMSC9115 ethernet controller
which is not present on the ARMv8 foundation model.

Tested on ARMv8 foundation model v1 and v2 by running ping/tftp
between the foundation model and the host PC via a bridged network.

Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
2014-01-17 08:04:31 -05:00
Łukasz Majewski
6e5d1db3c4 ARM: trats2: dfu: Enable default Poll Timeout for Trats2 board
Provide default Poll Timeout value for Trats2 board.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
2014-01-17 08:04:31 -05:00
Łukasz Majewski
c4e96dbfcc config: Update envs for trats and trats2 - Disable L2 cache
Disable L2 caches for Trats and Trats2 devices.

It turns out that for data downloading with thordown command L2 cache
disablement brings a significant speed improvement.

rootfs - 400 MiB:
- L2 cache enabled:			2.69 MiB/s
- L2 cache disabled: 			5.56 MiB/s

Such improvement is possible due to reduction of the need to invalidate
redundant data, which resides in L2 cache.

Since the sent USB request size at once is 512B (L1 - 32 KiB in total) -
one can be quite confident that it is already available in L1 and L2 can
be disabled.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
2014-01-17 08:04:28 -05:00
Łukasz Majewski
cdd15bcebc config: Update envs for trats and trats2 - new entries for new partitions
This patch adds extra dfu_alt_info entries to support storing the whole BOOT
, DATA and UMS partitions.
This allows upgrade of uImage and device tree blob (dtb) files at once.

Now it is also possible to store ext4 rootfs prepared with well established
linux tools (like mkfs.ext4).

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
2014-01-16 20:13:22 -05:00
Tom Rini
4913fc23f0 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-01-16 13:50:16 -05:00
Nobuhiro Iwamatsu
c71b4dd2da arm: koelsch: Add support QSPI device and enable boot from SPI flash
This supports SH-QSPI device on koelsch board, and enable booting from
SPI flash.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-01-16 08:07:20 +09:00
Nobuhiro Iwamatsu
0e05b217c2 arm: lager: Add support QSPI device and enable boot from SPI flash
This supports SH-QSPI device on lager board, and enable booting from
SPI flash.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-01-16 08:07:20 +09:00
Albert ARIBAUD
bf46e7d8d1 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2014-01-15 15:18:04 +01:00
Fabio Estevam
3a21773129 mx6: Add initial support for the Hummingboard solo
SolidRun has designed the Hummingboard board based on mx6q/dl/solo.

Add the initial support for the mx6 solo variant.

More information about this hardware can be found at:
http://imx.solid-run.com/wiki/index.php?title=Carrier-One_Hardware

(Carrier-One was the previous name of Hummingboard).

Based on the work from Jon Nettleton <jon.nettleton@gmail.com>.

Signed-off-by: Jon Nettleton <jon.nettleton@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-01-15 10:33:25 +01:00
Tom Rini
b5c068f3f8 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-01-14 14:48:42 -05:00
Albert ARIBAUD
e6fe4bd989 Merge 'u-boot-imx/master' into 'u-boot-arm/master' 2014-01-14 11:50:54 +01:00
Albert ARIBAUD
e570aca947 mx1ads: remove board support
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Stefano Babic <sbabic@denx.de>
2014-01-14 08:23:46 +01:00
Tom Rini
0effc5e567 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-01-13 13:50:25 -05:00
Marek Vasut
4efd69250f ARM: pxa: Fix OneNAND window access on VPAC270
Access the OneNAND 1KiB window on the VPAC270 as an SRAM instead of accessing
it as a burst-RAM. This fixes a problem where the board failed to reboot
sometimes as the CPU couldn't start executing from the OneNAND 1KiB window.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
2014-01-13 12:39:10 +01:00
Inderpal Singh
7da7651251 usb: exynos5: arndale: Add network support
Arndale board has AX88760, which is USB 2.0 Hub & USB 2.0 Ethernet Combo
controller, connected to HSIC Phy of USB host controller via USB3503 hub.

This patch uses board specific board_usb_init function to perform reset
sequence for USB3503 hub and enables the relevant config options for
network to work.

Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
2014-01-13 12:23:28 +01:00
Fabio Estevam
a6bbee6619 mx6slevk: Include "mx6_common.h"
Include "mx6_common.h" so that some ARM errata are applied and also the
vddsoc regulator can be changed.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2014-01-13 11:52:28 +01:00
John Weber
f353397011 wandboard: Set default environment to use zImage
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.

The zImage works for FSL Linux's kernel fork versions 3.0.35, 3.10.9,
and 3.10.17; this also works fine for mainline kernels.

Signed-off-by: John Weber <rjohnweber@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2014-01-13 11:52:28 +01:00
Otavio Salvador
03ce330274 mx6sabresd: Add eMMC specific environment to allow U-Boot update
A new 'update_emmc_firmware' target is added to allow for easy U-Boot
update in the eMMC as it has secury boot partition and this needs
specific handling on how to program the specific partition.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2014-01-13 11:52:28 +01:00
Linus Walleij
7d7c497d59 ARM: versatile: pass console setting to the kernel
The Versatiles come up with the primary UART set to ttyAMA0 at
38400 baud, and unless we pass this to the kernel it will assume
it is set to 9600 baud which will be quite awkward for the
terminal, let's try to be helpful and inform the kernel what
setting is used.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-01-13 09:46:11 +01:00
Tom Rini
7f673c99c2 Merge branch 'master' of git://git.denx.de/u-boot-arm
Bringing in the MMC tree means that CONFIG_BOUNCE_BUFFER needed to be
added to include/configs/exynos5-dt.h now.

Conflicts:
	include/configs/exynos5250-dt.h

Signed-off-by: Tom Rini <trini@ti.com>
2014-01-10 10:56:00 -05:00
Jagannadha Sutradharudu Teki
c91d0c74cf zynq: Enable CONFIG_DEFAULT_DEVICE_TREE
Enabled default dts files on respective pre-board config
files this is way MAKEALL will works. and it's upto user
to build specific dts by specifying at build time.

$ make zynq_zc70x_config
$ make -->  with default dts zynq-zc702.dts
or
$ make DEVICE_TREE=zynq-zc702 --> Same configuration with zynq-zc706.dts

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10 15:18:33 +01:00
Jagannadha Sutradharudu Teki
a8826eb4b3 zynq-common: Enable verified boot(RSA)
CONFIG_FIT_SIGNATURE - signature node support in FIT image
CONFIG_RSA - RSA lib support

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10 15:18:33 +01:00
Jagannadha Sutradharudu Teki
f8f36c5dda dts: zynq: Add basic fdt support
This patch provides a basic fdt support for zynq u-boot.

zynq-7000.dtsi-> initial arch dts file
zynq-zed.dts -> initial zed board dts file
more devices should be added in subsequent patches.

u-boot build: once configuring of a board done
for building dtb with zynq-zed.dts as an input
zynq-uboot> make DEVICE_TREE=zynq-zed

Enabled CONFIG_OF_SEPARATE for building dtb separately.
There is a new binary called u-boot-dtb.bin which is a u-boot
with devicetree supported.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10 15:18:33 +01:00
Jagannadha Sutradharudu Teki
b660ca13a8 zynq-common: Define CONFIG_ENV_OVERWRITE
Defined CONFIG_ENV_OVERWRITE, which allow to
overwrite serial baudrate and ethaddr.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10 15:18:33 +01:00
Jagannadha Sutradharudu Teki
ed53e4d690 zynq-common: Define flash env. partition
Last 128Kb sector of 1Mb flash is defined as u-boot
environment partition.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10 15:18:33 +01:00
Jagannadha Sutradharudu Teki
18eee22f4c zynq-common: Change Env. Sector size to 128Kb
Changed Env. Sector size from 0x10000 to 128Kb

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10 15:18:33 +01:00
Jagannadha Sutradharudu Teki
e83f61a6b3 zynq-common: Define default environment
Defined default env. for autoboot FIT image from
respective boot devices.

Default settings:
fit_image=fit.itb
load_addr=0x2000000
fit_size=0x800000
flash_off=0x100000
nor_flash_off=0xE2100000

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10 15:18:33 +01:00
Jagannadha Sutradharudu Teki
b3de92495f zynq: Add support to find bootmode
Added support to find the bootmodes by reading
slcr bootmode register. this can be helpful to
autoboot the configurations w.r.t a specified bootmode.

Added this functionality on board_late_init as it's not
needed for normal initializtion part.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10 15:18:33 +01:00
Jagannadha Sutradharudu Teki
fe5eddbf98 zynq: Add zynq_zc770 xm012 board support
ZC770 is a complete development board based on the Xilinx Zynq-7000
All Programmable SoC, similar to ZC70x board but which has four
different daughter cards, like XM010, XM011, XM012 and XM013

ZC770 XM012:
- 1GB DDR3
- 64MiB Numonyx NOR flash
- USB-UART

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Cc: Stefan Roese <sr@denx.de>
2014-01-10 15:18:33 +01:00
Jagannadha Sutradharudu Teki
309a9165f8 zynq: Add zynq_zc770 xm013 board support
ZC770 is a complete development board based on the Xilinx Zynq-7000
All Programmable SoC, similar to ZC70x board but which has four
different daughter cards, like XM010, XM011, XM012 and XM013

ZC770 XM013:
- 1GB DDR3
- 128 Mb Quad-SPI Flash(dual parallel)
- USB-UART

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10 15:18:33 +01:00
Jagannadha Sutradharudu Teki
e1d3425b0b zynq: Add zynq_zc770 xm010 board support
ZC770 is a complete development board based on the Xilinx Zynq-7000
All Programmable SoC, similar to ZC70x board but which has four
different daughter cards, like XM010, XM011, XM012 and XM013

ZC770 XM010:
- 1Gb DDR3
- 1Mb SST SPI flash
- 128 Mb Quad-SPI Flash
- 8 Mb SST SI flash
- Full size SD/MMC card cage
- 10/100/1000 Ethernet
- USB-UART

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10 15:18:33 +01:00
Jagannadha Sutradharudu Teki
e3b01de78c zynq: Add zynq microzed board support
MicroZed is a low-cost development board based on
the Xilinx Zynq-7000 All Programmable SoC.

APSOC:
- XC7Z010-1CLG400C
Memory:
- 1 GB of DDR3 SDRAM
- 128Mb of QSPI flash(S25FL128SAGBHI200)
- Micro SD card interface
Communication:
- 10/100/1000 Ethernet
- USB 2.0
- USB-UART
User I/O:
- 100 User I/O (50 per connector)
- Configurable as up to 48 LVDS pairs or 100 single-ended I/O
Misc:
- Xilinx PC4 JTAG configuration port
- PS JTAG pins accessible via Pmod
- 33.33 MHz oscillator
- User LED and push switch

For more info - http://zedboard.org/product/microzed

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10 15:18:33 +01:00
Jagannadha Sutradharudu Teki
65da1efde2 zynq: zc70x: Add Catalyst 24WC08 EEPROM config support
Adds configurations for Catalyst 24WC08 EEPROM, which
is present on the zynq boards.

Enable EEPROM support for zc70x boards.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10 15:18:33 +01:00
Jagannadha Sutradharudu Teki
0f5c215650 zynq-common: Define exact TEXT_BASE
Defined TEXT_BASE for u-boot starts from 0x4000000
w.r.t zynq memory-map.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10 15:18:33 +01:00
Jagannadha Sutradharudu Teki
86737bcf07 zynq: Move CONFIG_SYS_SDRAM_SIZE to pre-board configs
CONFIG_SYS_SDRAM_SIZE is specific to a board hence moved
to specific pre-config board files.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10 15:18:33 +01:00
Jagannadha Sutradharudu Teki
796d49969e zynq: Add zynq zed board support
Zed is a complete development board based on the
Xilinx Zynq-7000 All Programmable SoC.

APSOC:
- XC7Z020-CLG484-1
Memory:
- 512 MB DDR3
- 256 Mb Quad-SPI Flash(
- Full size SD/MMC card cage
Connectivity:
- 10/100/1000 Ethernet
- USB OTG (Device/Host/OTG)
- USB-UART
Expansion:
- FMC (Low Pin Count)
- Pmod. headers (2x6)
Video/Display:
- HDMI output (1080p60 + audio)
- VGA connector
- 128 x 32 OLED
- User LEDs (9)
User inputs:
- Slide switches (8)
- Push button switches (7)
Audio:
- 24-bit stereo audio CODEC
- Stereo line in/out
- Headphone
- Microphone input
Analog:
- Xilinx XADC header
- Supports 4 analog inputs
- 2 Differential / 4 Single-ended
Debug:
- On-board USB JTAG programming port
- ARM Debug Access Port (DAP)

For more info - http://zedboard.org/product/zedboard

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10 15:18:33 +01:00
Jagannadha Sutradharudu Teki
022b02064a zynq: Add zynq zc70x board support
The Zynq-7000 APSOC zc702 and zc706 enabled complte embedded
processing includes ASIC and FPGA design.

ZC702-:

APSOC:
- XC7Z020-CLG484-1
Memory:
- DDR3 Component Memory 1GB
- 16MB Quad SPI Flash
- IIC - 1 KB EEPROM
Connectivity:
- Gigabit Ethernet GMII, RGMII and SGMII.
- USB OTG - Host USB
- IIC Bus Headers/HUB
- 1 CAN with Wake on CAN
- USB-UART
Video/Display:
- HDMI Video OUT
- 8X LEDs
Control & I/O:
- 3 User Push Buttons
- 2 User Switches
- 8 User LEDs

For more info on zc702 board:
- http://www.xilinx.com/products/boards-and-kits/EK-Z7-ZC702-G.htm

ZC706-:

APSOC:
- XC7Z045 FFG900 -2 AP SoC
Memory:
- DDR3 Component Memory 1GB (PS)
- DDR3 SODIM Memory 1GB (PL)
- 2X16MB Quad SPI Flash (dual parallel)
- IIC - 1 KB EEPROM
Connectivity:
- PCIe Gen2x4
- SFP+ and SMA Pairs
- GigE RGMII Ethernet (PS)
- USB OTG 1 (PS) - Host USB
- IIC Bus Headers/HUB (PS)
- 1 CAN with Wake on CAN (PS)
- USB-UART
Video/Display:
- HDMI 8 color RGB 4.4.4 1080P-60 OUT
- HDMI IN 8 color RGB 4.4.4
Control & I/O:
- 2 User Push Buttons/Dip Switch, 2 User LEDs
- IIC access to GPIO
- SDIO (SD Card slot)
- 3 User Push Buttons, 2 User Switches, 8 User LEDs

For more info on zc706 board:
- http://www.xilinx.com/products/boards-and-kits/EK-Z7-ZC706-G.htm

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10 15:18:32 +01:00
Jagannadha Sutradharudu Teki
06fe8daeb5 zynq-common: Rename zynq with zynq-common
zynq.h -> zynq-common.h, zynq-common is Common
configuration options for all Zynq boards.

zynq.h is no longer exists hense removed from boards.cfg

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10 15:18:32 +01:00
Jagannadha Sutradharudu Teki
88fcfb1ce7 zynq: Add GEM0, GEM1 configs support
Zynq ethernet controller support two GEM's like
CONFIG_ZYNQ_GEM0 and CONFIG_ZYNQ_GEM1 enabled
both so-that the respective board will define
these macros based on their usage.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10 15:18:32 +01:00
Jagannadha Sutradharudu Teki
625d763751 zynq: Add UART0, UART1 configs support
Zynq uart controller support two serial ports like
CONFIG_ZYNQ_SERIAL_UART0 and CONFIG_ZYNQ_SERIAL_UART1
enabled both so-that the respective board will define
these macros based on their usage.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10 15:18:32 +01:00
Jagannadha Sutradharudu Teki
8cfac50442 zynq: Enable cache options
- Enable cache command
- Turn-off L2 cache
- Turn-on D-cache

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10 15:18:32 +01:00
Jagannadha Sutradharudu Teki
53e49f746c zynq: Minor config cleanup
Cleanups mostly on:
- Add comments
- Re-order configs
- Remove #define CONFIG_ZYNQ_SDHCI

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10 15:18:32 +01:00