Use board_early_init_f() for per-board init operation and
use board_init() from common board file.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Use common board file for board_init() and board_late_init(),
for Rockchip SoCs have very similar process.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Handle per-board init in board_early_init_f() and use the
common board_init() for per-platform board init later.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Use common board file for board_init() and board_late_init(),
for Rockchip SoCs have very similar process.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Use common board file for board_init() and board_late_init(),
for Rockchip SoCs have very similar process.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
The rk3288_detect_reset_reason() is per-SoC operation, move
it to rk3288.c, and extend the rk_board_late_init() with
rk3288_board_late_init() to make all the board works fine
as before.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The veyron_init() should go to its board file veyron.c,
and the board_early_init_f() could be the right place.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Use "snps,dwc2" for compatible name and and common variable
names so that we can share the common code for all SoCs.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add a board_early_init_f() in board_init_f() and move the board
specific init code into its own board file.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Only firefly-rk3288 has the dts node "u-boot,boot-led",
while CONFIG_SPL_LED is not enable, move code to firefly-rk3288
now in case someone need this code.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Extend the driver to build with DM_VIDEO enabled. DTS files
must additionally include 'u-boot,dm-pre-reloc' property in
soc and child nodes to enable driver binding to fsl_dcu_fb device.
Currently display timings aren't obtained from DT.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Move dcu-related code to fsl_dcu_probe_common, keep in video_hw_init()
only legacy video stack (filling GraphicPanel struct etc.).
Add wrappers for all init functions, that will let to provide
struct fb_info as an additional param (needed for further moving it from
the global scope to driver private data struct in DM converted driver).
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
This patch enables the pinmuxing to support gpio_57 for phy reset
and fixes the pinmuxing for the ECHI tranceiver. The clocks
don't appear to by fully enabled yet, so OMAP-EHCI on am3517 is
still not yet working, but we're one step closer.
Signed-off-by: Adam Ford <aford173@gmail.com>
The SOM-LV boards support the OMAP EHCI driver using port 2.
With the driver updated to support device tree, this patch sets
the corresponding pin muxing for the tranceiver as well as the
reset pin.
Signed-off-by: Adam Ford <aford173@gmail.com>
With both SPL and U-Boot now supporting DM, we can start removing
legacy code. This patch removes the legacy MMC initalization and
legacy I2C initialization since both are now available via DM and
device tree.
Signed-off-by: Adam Ford <aford173@gmail.com>
arch_cpu_init() initializes the pinmuxing which is called fairly
early in the start sequences, so the board_init function doesn't
need to do it again. This patch removes the call from board_init.
Signed-off-by: Adam Ford <aford173@gmail.com>
The Low Level init functions start the UART, so it doesn't need
to happen during board_init. This patch removes it from
board_init.
Signed-off-by: Adam Ford <aford173@gmail.com>
The reset line going to the ethernet controller is controlled
by a global reset controlling multiple peripherals. There
is no need to manually invoke the reset.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add initial defconfig support for J721e that runs on A72.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Add MAINTAINERS entry]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add initial defconfig support for J721e that runs on R5.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Add MAINTAINERS file]
Signed-off-by: Tom Rini <trini@konsulko.com>
Create a ft_board_setup() api that gets called as part of
DT fixup before jumping to kernel. In this ft_board_setup()
call fdt_fixup_msmc_ram that update msmc sram node.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Now that we removed all legacy boards selecting TI_EMAC we can
completely convert the driver code to using the driver model.
This patch also updates all remaining users of davinci_emac.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Adam Ford <aford173@gmail.com> #am3517-evm & da850-evm
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The LS1021A-TSN is a development board built by VVDN/Argonboards in
partnership with NXP.
It features the LS1021A SoC and the first-generation SJA1105T Ethernet
switch for prototyping implementations of a subset of IEEE 802.1 TSN
standards.
Supported boot media: microSD card (via SPL), QSPI flash.
Rev. A of the board uses a Spansion S25FL512S_256K serial flash, which
is 64 MB in size and has an erase sector size of 256KB (therefore,
flashing the RCW would erase part of U-Boot).
Rev. B and C of the board use a Spansion S25FL256S1 serial flash, which
is only 32 MB in size but has an erase sector size of 64KB (therefore
the RCW image can be flashed without erasing U-Boot).
To avoid the problems above, the U-Boot base address has been selected
at 0x100000 (the start of the 5th 256KB erase sector), which works for
all board revisions. Actually 0x40000 would have been enough, but
0x100000 is common for all Layerscape devices.
eTSEC3 is connecting directly to SJA1105 via an RGMII fixed-link, but
SJA1105 is currently not supported by uboot. Therefore, eTSEC3 is
disabled.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Jianchao Wang <jianchao.wang@nxp.com>
Signed-off-by: Changming Huang <jerry.huang@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
[Vladimir] Code taken from https://github.com/openil/u-boot (which
itself is mostly copied from ls1021a-iot) and adapted with the following
changes:
- Add a008850 errata workaround
- Converted eTSEC, MMC to DM to avoid all build warnings
- Plugged in distro boot feature, including support for extlinux.conf
- Added defconfig for QSPI boot
- Added the board/freescale/ls1021atsn/README.rst for initial setup
- Increased CONFIG_SYS_MONITOR_LEN so that the SPL malloc pool does not
get overwritten during copying of the u-boot.bin payload from MMC to
DDR.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Now that we have added driver model support to the TSEC driver,
convert ls1021atwr board to use it.
This depends on previous DM series for ls1021atwr:
http://patchwork.ozlabs.org/patch/561855/
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
[Vladimir] Made the following changes:
- Added 'status = "disabled";' for all Ethernet ports in ls1021a.dtsi
- Fixed the confusion between the SGMII/TBI PCS for enet0 and enet1 -
a mistake ported over from Linux. Each SGMII PCS lies on the private
MDIO bus of the interface (and the RGMII enet2 has no SGMII PCS).
- Added CONFIG_DM_ETH to all ls1021atwr_* defconfigs
- Completely removed non-DM_ETH support from ls1021atwr
- Changed "compatible" string from "fsl,tsec-mdio" to "fsl,etsec2-mdio"
and from "fsl,tsec" to "fsl,etsec2" to match Linux
Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Update "dma-ranges" DT property of all PCIe controllers in the system
with the up-to-date DRAM layout. This allows the PCIe controller take
full advantage of all the available DRAM.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
- rk3399 lpddr4 support
- rk3399-rock960 board support improvement
- Eliminate pyelftools dependency by make_fit_atf.py
- clean up rockchip dts to use -u-boot.dtsi
- use ARM arch/generic timer instead of rk_timer
- clean up Kconfig options for board support
make_fit_atf.py no longer requires pyelftools, and nothing else in the
rockchip build requires it either, so remove references to installing it
from the documentation.
Signed-off-by: Chris Webb <chris@arachsys.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
This patch enables DM I2C for DHCOM i.MX6 PDK2 boards and
removes non DM I2C code. The I2C EEPROM with ethaddr (MAC)
is defined in the device tree. Use UCLASS_I2C_EEPROM
to find the device by fixed hardware path and read the ethaddr.
Tested with DHCOM i.MX6dl and DHCOM i.MX6q.
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
It turned out that after a reset the boot process from the spi bootflash is
disturbed by other spi slave devices connected to DHCOM SPI1, which uses the
same spi interface with a different SS line.
Therefore the pad pull ups are enabled.
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
Fix issue as reported by checkpatch.pl. Leave long lines as line
continuation in text output is not recommended.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
The Apalis iMX8 was missing the interactive part should a customer have
bricked his module and want to re-create the configuration block. Fix
this.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
The Colibri iMX8X target got re-named late in the cycle which we forgot
to reflect here. Furthermore, it was missing the interactive part should
a customer have bricked his module and want to re-create the
configuration block. Fix this.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Make the interactive Wi-Fi/BT handling generic by pulling it out of the
Colibri iMX6ULL interactive part to be re-used for Apalis iMX8 and
Colibri iMX8X.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
If the module is in serial downloader mode, we do no longer read the
environment from eMMC. Therefor, the eMMC is unitialized when trying
to read the config block. Use mmc_init to initialize the selected
MMC device before using it.
Note: In case the MMC has already been initialized, the mmc_init
detects that and returns immediately.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Configure fitImage for U-Boot with a device tree for imx6 quad/dual
and duallite/solo. This enables to support the imx6 derivates
quad/dual/duallite/solo with a single binary.
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Enable DM support for regulators and fixed regulator driver and
convert USB Vbus control over to the regulators defined in DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: Ludwig Zenz <lzenz@dh-electronics.com>
imx6ul-isiot-mmc.dts was removed in uboot version v2018.03 and from then
onwards IMX6UL isiot uses imx6ul-isiot-emmc.dts for mmc, so remove
unnecessary check for mmc.
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
Secure boot is not enabled in mx6sxsabresd imximage.cfg, add support
for it.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
New imx8 boards started adding duplicated UART init code.
Factor out this to common function sc_pm_setup_uart().
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Before the wide DM/DTS adoption in the U-Boot proper, the display5
has been using only DM_SERIAL to provide serial console in
pre-relocation.
After moving to full DM/DTS adoption in the U-Boot proper the
U_BOOT_DEVICE definition is not needed anymore, as it has been
replaced with udevice creation from provided DTS description.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
After commit 14453fbfad ("Convert CONFIG_SF_DEFAULT_* to Kconfig")
and commit abe66b1b5d ("Convert CONFIG_ENV_SPI_* to Kconfig") ,which
moved some SPI related CONFIG_* defines to Kconfig the display5 board has
become unbootable as the SPI CS check condition had wrong value.
This commit fixes this check and allows proper SPI NOR flash operation in
SPL.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This function sets the polarity of the PWR signal which is not used on
the opos6uldev board. Remove it.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
On i.MX7ULP B0, the DDR clock target is increased from 320Mhz to 380Mhz.
We update DDR clock relevant settings to approach the target. But since the
limitation on LCDIF pix clock for HDMI output
(refer "mx7ulp_evk: Change APLL and its PFD0 frequencies"), we set DDR
clock to 352.8Mhz (25.2Mhz * 14) by using the clock path:
APLL PFD0 -> DDR CLK -> NIC0 -> NIC1 -> LCDIF clock
To reduce the impact to entire system, the NIC0_DIV and NIC1_DIV are kept,
so the divider 14 is calculated as:
14 = (NIC0_DIV + 1) * (NIC1_DIV + 1) * (LCDIF_PCC_DIV + 1)
NIC0_DIV: 1
NIC1_DIV: 0
LCDIF_PCC_DIV: 6
APLL and APLL PFD0 settings:
PFD0 FRAC: 27
APLL MULT: 22
APLL NUM: 1
APLL DENOM: 20
This patch applies the new settings for both DCD and plugin.
There is no DDR script change on this new frequency.
Overnight memtester is passed.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Due to the APLL out glitch issue, the APLLCFG PLLS bit must
be set to select SCG1 APLL PFD for generating system clock to align
with the design.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
To support HDMI display on EVK board, the LCDIF pix clock must be
25.2Mhz. Since the its PCC divider range is from 1-8, the max rate
of LCDIF PCC source clock is 201.6Mhz. This limits the source clock
must from NIC1 bus clock or NIC1 clock, other sources from APLL PFDs
are higher than this max rate.
The NIC1 bus clock and NIC1 clock are from DDRCLK whose parent source
is APLL PFD0, so we must change the APLL PFD0 and have impact to DDRCLK,
NIC1 and NIC1 bus.
Eventually, this requests to set the APLL PFD0 frequency to 302.4Mhz
(25.2 * 12), with settings:
PFD0 FRAC: 32
APLL MULT: 22
APLL NUM: 2
APLL DENOM: 5
Signed-off-by: Ye Li <ye.li@nxp.com>
Tested-by: Fancy Fang <chen.fang@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update LPDDR3 script with the changes below:
-Update the precharge command to CMD=01 at the DDR initialization phase
-remove unimplemented registers
Write data bit delay --refer to the DDR_TRIM bits in
IOMUXC1_DDR_SW_PAD_CTL_PAD_DDRn
Test:
One EVK board passes overnight stress test.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
For the current APLL setting, as we want the APLL PFD0 to meet DDR clock 320Mhz requirement.
We set MULT to 20, NUM to 4 and DENOM to 2, to get final 22 multiplier. But according to the RM,
the NUM should always be less than the DENOM. So our setting violates the rule.
Actually the ROM has already set the MULT to 22 and leave NUM/DENOM in default value. The calculated APLL PFD0 clock
is 318.9888Mhz, which also meet the DDR requirement.
To fix the issue, we remove the PLL settings in DCD to use default value from ROM, and only set the PFD0 FRAC.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since the board uses SPL_OF_CONTROL now, we don't need to
explicitly initialize the MMC driver, but we still need to
pinmux the corresponding pins. This patch removes the
initialization code and leave just the muxing behind.
Signed-off-by: Adam Ford <aford173@gmail.com>
This patch enables SiFive SPI and MMC SPI drivers for the
SiFive Unleashed board.
Signed-off-by: Bhargav Shah <bhargavshah1988@gmail.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This patch extends SiFive FU540 board support to setup ethaddr
env variable based on board serialnum read from OTP.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The GEMGXL clock driver is now directly part of Cadence MACB
ethernet driver in upstream Linux kernel. There is no separate
GEMGXL clock driver in upstream Linux kernel hence we drop
GEMGXL clock driver from U-Boot as well.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- Various FS/disk related fixes with security implications.
- Proper fix for the pci_ep test.
- Assorted bugfixes
- Some MediaTek updates.
- 'env erase' support.
libvirt v.5.3.0 with QEMU 4.0.0 or above uses PCI automatically and
thus devices (network, storage, etc) are connected via PCI.
Signed-off-by: David Abdurachmanov <david.abdurachmanov@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The TI AM654x EVM base board and the associated daughtercards have on-
board I2C-based EEPROMs containing board configuration data. Use the
board detection infrastructure introduced earlier to do the following:
1) Parse the AM654x EVM base board EEPROM and populate items like board
name and MAC addresses into the TI common EEPROM data structure
residing in SRAM scratch space
2) Check for presence of daughter card(s) by probing the associated
presence signals via an I2C-based GPIO expander. Then, if such a
card is found, parse the data such as additional Ethernet MAC
addresses from its on-board EEPROM and populate into U-Boot
accordingly
3) Dynamically create an U-Boot ENV variable called overlay_files
containing a list of daugherboard-specific DTB overlays based on
daughercards found.
This patch adds support for the AM654x base board ("AM6-COMPROCEVM")
as well as for the IDK ("AM6-IDKAPPEVM"), OLDI LCD ("OLDI-LCD1EVM")
PCIe/USB3.0 ("SER-PCIEUSBEVM"), 2 Lane PCIe/USB2.0 ("SER-PCIE2LEVM"),
and general purpuse ("AM6-GPAPPEVM") daughtercards.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The AM654x EVM based on the TI K3 family of SoCs has an updated board
detection EEPROM structure that contains a TLV record of dedicated MAC
addresses rather than a range of MAC addresses as it was used on earlier
platforms such as DRA7. Add a basic function that allows us setting up
Ethernet MAC addresses into the U-Boot environment based on the MAC
address record contained in the common TI EEPROM structure.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The AM654x EVM based on the TI K3 family of SoCs have an updated board
detection EEPROM structure, now comprising variable-sized TLV-type
records, containing a superset of what is already being provided on
earlier platforms such as DRA7. Add basic support for parsing the new
data structures contained on the base board into the common TI EEPROM
structure while also providing infrastructure that can be used later on
to parse data from additional EEPROMs such as the ones that are used on
daughtercards for this platform.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Add instructions for flashing boot images to the eMMC with a
layout of the address where each image needs to be flashed.
Also add instructions to flash filesystem partition in user
partition and boot kernel from the rootfs.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Use the System Firmware (SYSFW) loader framework to load and start
the SYSFW as part of the AM654 early initialization sequence. While
at it also initialize the WKUP_UART0 pinmux as it is used by SYSFW
to print diagnostic messages.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot,
2 USB ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using the
SoC's integrated PHY, Wifi via an sdio wifi chip, HDMI, an IR receiver, a
dual colour LED and an optical S/PDIF connector.
Linux commit details about the sun8i-h3-beelink-x2.dts sync:
"ARM: dts: sun8i: h3: Add ethernet0 alias to Beelink X2"
(sha1: cc4bddade114b696ab27c1a77cfc7040151306da)
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
With a recent update to the pinctrl-single driver and the fact
that the da850evm has both DM and OF_CONTROL working in both SPL
and U-Boot, some of the manual pinmuxing can be setup to only
be activated when either the driver doesn't have DM for it, or
when CONFIG_PINMUX isn't available (only during SPL). If the
code ever shrinks enough to support PINCTRL in SPL, a lot of this
can go away. This also remove some manual pinmuxing not needed
by SPL to give SPL a little more breathing room.
Signed-off-by: Adam Ford <aford173@gmail.com>
This converts LEGO MINDSTORMS EV3 to the driver model. MMC, SERIAL, SPI
and SPI_FLASH are converted.
The device tree contains only the minimal nodes required by U-Boot
since the size of U-Boot is limited to 256K on this device.
Signed-off-by: David Lechner <david@lechnology.com>
This addresses the following warning message:
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
As USB support for older OMAP3 SoC's improves, OMAP3 EVM can be
readily adapted. There is some additional 'gpio-hog' support
needed to fully setup USB in a similar manner to Linux.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
This patch solves the following warnings:
warning: no previous prototype for 'board_quiesce_devices' [-Wmissing-prototypes]
void board_quiesce_devices(void)
^~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add support of Trusted boot chain with OP-TEE
- reserved 32MB at the end of the DDR for OP-TEE
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
U-Boot activates regulators by reading the "regulator-boot-on"
property in DT; it is requested by M4 early Boot feature.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
- Minor tracing and PCI improvements
- Various other minor fixes
- Conversion of patman, dtoc and binman to support Python 3
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl0nbDoRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZcBQgAn+ojgq/hD89bihuhz2oEe6rhzHB9OkcC
sHrVL8Jbmby/BuzISGe4oeeM5yVygBVtUiN/72JiiAHLmykqc4CpRjNvgOOAgKCy
Ml8UyiBNNVNfrD6f9PxAKvPZf6S0gfLnomGOQ/psdEojpY5AvQxQ36D+QFZ0AMP5
67/xjSfN9bNPw8UbgE/VhJ+WFbU948BP2EBt6+NBAtv7HW4AX9vT0famJfWEjwq8
ftmcFOSNGgYcDQ5BwQWX1sFhnwb9XSfurlQsVYBsFA4cx4gj0DfUm1Ugr4wDD+lo
91P+76hSBQ+mHp1HJ90WMd2vAaElG7/SoaicXo9pW6Rc7WIgTjk7gg==
=SdZy
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-9jul19-take2' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
- Sandbox improvements including .dts refactor
- Minor tracing and PCI improvements
- Various other minor fixes
- Conversion of patman, dtoc and binman to support Python 3
KM Kirkwood boards now implement the driver model for its SPI flash
interface. Therefore, the old board specific claim and release functions
can be deleted. The preprocessor definition CONFIG_SYS_KW_SPI_MPP is yet
unused as well. All its appearances and dependencies are removed in the
kirkwood_spi driver, header files and finally the configuration whitelist.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The corresponding configurations are selected in the common Kconfig file.
This is easier than changing every affected board default configuration
file. The default configuration for the PORTL2 board, however, still needs
some modifications to correctly use the driver model.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
As the SPI NOR and NAND devices share the same hardware pins, the MPP
configuration has to be changed when claiming/releasing the bus. The
current configuration is saved when claiming and restored when releasing.
Furthermore, a general-purpose output is used to switch the chip-select
signal. This is now also implemented for the DM part of the kirkwood_spi
driver.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
As preparation for the upcoming transferring of configurations from header
files to Kconfig, a common Kconfig file for all KM boards was created. For
the moment, it only sources the other three, more specific, Kconfig files.
Therefore, the architecture Kconfig files now include the common Kconfig
file. Also, the configuration selection for KM boards was moved from the
architecture Kconfig files to the board specific Kconfig files.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Rescue mode bootcmd currently only appends the "omniarescue" parameter
to the bootargs variable. We do not want the user to be able to change
rescue mode bootargs. Therefore change this so that bootcmd sets the
bootargs variable in an absolute way (adding console device information
and the omniarescue paramterer).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
We always want to enumerate PCIe devices, because withouth this they
won't work in Linux.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The board code reads MAC addresses from the ATSHA204A cryptochip.
For compatibility reasons the ethernet adapters on this SOC are not
enumerated in register address order. But when Omnia was first
manufactured this was done differently.
Change setting of MAC addresses to conform to the description on the
stickers sticked on actual Omnias.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Document the main U-Boot image offset when booting from SATA disk on the
Clearfog board.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
When cross-compiling, sometimes sdl-config must come from a different path
from the default. Add a way to override it, by adding SDL_CONFIG to the
environment before building U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdJEZEAAoJEB6zHgIOrC/I+LAH/jUDQpF5I68h0ZFGm3xoyGhm
3CSv8viOm/kL+GLubjnv4cwAp8N8VRpeJekz0Jt1Xp8C6OIgtnJ2Fln72KD+Z0IC
Rq7ByRS16iq4b6IUDRZObE4Jzxmf7rXU3jr0+/vd/en7kxVlvA9+Gsffs3OTGxC7
z9PysRZPBMH/smIPXdEQxYifnbpDG4fmfGcUWKrYfkB0Kq6Ep98Ia/gXNCY8XJ/A
sbNQGjJWJZWXS/TDetcC2VikssJ+yNFF34uzV+HD5Y3DW6ywLhuoDOz1pg8RR36i
YjcTCQz8lL/UVaUzrGUgPVAC3gdKY6J26GtV3vZavxBcmtGf0FhVtXO/tZc9AsY=
=6G45
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2019.10-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel features and fixes for 2019.10 cycle
This includes the Atmel QSPI driver and support for the at91 boards.
This is the port of the driver from Linux, mostly done by Tudor Ambarus.
Add the default config file of QSPI media. The config is based on
sama5d27_som1_ek_mmc_defconfig.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add the default config file of QSPI media. The config is based on
sama5d2_xplained_mmc_defconfig.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
- add support for unique generated MAC adresses from SoC serial,
limited to Amlogic GXL/GXM boards for now
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BL1s
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20190704' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- fix khadas-vim README
- add support for unique generated MAC adresses from SoC serial,
limited to Amlogic GXL/GXM boards for now
Enable unique MAC address generation for boards usins SoCs having
a known functional and valid unique serial number.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Unlike the BayLibre repos Khadas' repo defaults to using native gcc,
so specify the CROSS_COMPILE setting matching the prescribed toolchain.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
After the conversion to DM the U-Boot proper binary name
is 'u-boot-dtb.img', so adjust it accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
After the transition to DM, only the mx6dl/solo wandboard
is supported.
Add FIT image support so that all the wandboard variants
can be supported, like it was prior to the DM conversion.
Successfully booted Linux on mx6q/solo/qp wandboards.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdGaVcAAoJEB6zHgIOrC/Ic1oH/3Hu55HbHVnA2QqRof/o6RnZ
VNJQ11+Zs7QA7TIMT/Z5j9ohX0pEkVPQziD9zAL1rz7WJ/laYkPh8wqsKWmfFD2j
2mCCnf8/vGvST8fiSv0BQ6cqozdMwdQjQ08Eqw0srJhCzqj/I8o8MNlts+OAXNIM
CyT7LdIr/QSO05zDYxFibki4qs7Q5S8WXbtjsmbAAYajcet5w5+hEZRAD2YXuUv8
TBuBWz6bgcSLbV7E7YXexoffgIha2K3ETAxWraKZLcc96MNLL054uBraa3dmybqZ
+0+PHIOcNk2JR4BQmUHCoNgEuKTBPlayxZ3hVUzWzUwot4gBRRUFu/pbnRtLcF4=
=RzN7
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2019.07-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel fixes for 2019.07 cycle
Enable DM Video support on iMX53 M53Menlo and fix minor details
to restore previous behavior of the system.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable DM block and DM MMC and DM USB support on iMX53 M53Menlo .
Convert board code to match the DM support. This also enables DM
pincontrol to configure the SDHI pins.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable DM GPIO support on iMX53 M53Menlo and fix up board code where
applicable. Enable MALLOC_F to let the GPIO controllers bind early on.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
After the conversion to DM the U-Boot binary is called u-boot-dtb.imx,
so fix the README file accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Joris Offouga <offougajoris@gmail.com>
In case someone detects a PDA and u-boot sets the 'pda' variable,
and the user does a saveenv, the pda is set in env, and if the
screen is removed, u-boot will still have in the env the 'pda'
variable, even if no screen is attached.
In order to fix this, we have to reset the 'pda' variable,
such that it's not just set if the screen is detected, but also unset
if no screen is detected.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
The new common rockchip pinctrl driver does not support explicit
requests for a particular pinctrl function. As a result, the
board_init() function bails out early before enabling the boot-on
regulators. Fix this by simply removing the request for pwm0, pwm2
and pwm3. The generic DM code already does the necessary
configuration if necessary.
Reported-by: Levin Du <djw@t-chip.com.cn>
Signed-of-by: Mark Kettenis <kettenis@openbsd.org>
Support common spl_board_init by moving code from puma
board file into, common rk3399-board-spl.c.
Part of the code has sysreset-gpio, regulators_enable_boot_on
but right now only puma board is using this with relevant
config options rest remains common for all targets.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
preloader_console_init is used for printing SPL boot banner that
usually called from spl_board_init.
The current spl_board_init in evb and rock960 is enabling explicit
pinctrl, debug uart prior to calling preloader_console_init which
eventually not required since board_init_f is already enabled
debug uart.
So, drop those explicit enablement calls from spl_board_init of
evb, rock960.
Tested this by enabling CONFIG_SPL_BOARD_INIT and adding
u-boot,dm-pre-reloc property for uart node.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add u-boot.itb BUILD_TARGET for Rockchip platform when SPL_LOAD_FIT
is being used.
This can get rid of building itb explicitly with 'make u-boot.itb'
so, from now all required images will build just by make.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Right now puma rk3399 board need to copy bl31-rk3399.bin and
rk3399m0.bin into u-boot source directory to make use of building
u-boot.itb.
So, add environment variable
- BL31 for bl31.bin (instead of bl31-rk3399.bin to compatible with other
platform BL31 env)
- PMUM0 for rk3399m0.bin
If the builds are not exporting BL31, PMUM0 env, the fit_spl_atf.sh will
notify with warning about which document to refer for more information
like this:
WARNING: BL31 file bl31.bin NOT found, resulting binary is non-functional
Please read Building section in doc/README.rockchip
WARNING: PMUM0 file rk3399m0.bin NOT found, resulting binary is non-functional
Please read Building section in doc/README.rockchip
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The ROCK64 is a credit card size SBC based on Rockchip RK3328
Quad-Core ARM Cortex A53.
This series allow building u-boot SPL and u-boot.itb for Rock64
board. The proprietary TPL is stil required for deploy:
./tools/mkimage -n rk3328 -T rksd \
-d ./rkbin/bin/rk33/rk3328_ddr_333MHz_v1.16.bin idbloader.img
cat ./spl/u-boot-spl.bin >> idbloader.img
dd if=idbloader.img of=/dev/sdcard seek=64 conv=notrunc
dd if=u-boot.itb of=/dev/sdcard seek=16384 conv=notrunc
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Converted to use fsl_esdhc_imx for i.MX platforms.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
Acked-by: Jason Liu <Jason.hui.liu@nxp.com>
Misspelling of SPDX-License-Identifier is rather fatal than other
general typos, so must be fixed.
This file spells SPDX-Licence-Identifier.
^
I also moved it to the very top of the file with // comment style.
Detected by grepping the source tree:
$ git grep --not -e SPDX-License-Identifier --and -e SPDX-
board/armltd/vexpress64/pcie.c: * SPDX-Licence-Identifier: GPL-2.0+
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Liviu Dudau <liviu.dudau@foss.arm.com>
Extra "not DM" controllers support is disabled.
u-boot BSP still good enough to upgrade and run images.
Signed-off-by: Oleksandr Zhadan <oleks@arcturusnetworks.com>
Signed-off-by: Michael Durrant <mdurrant@arcturusnetworks.com>
Compile the legacy PCIe initialization reoutines only when DM_PCI
is not enabled.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
- LS1046AFRWY support
- USB errata fix and secure boot defconfig support for LS1028A
- Enabled SDHC and SATA for LX2160
- LS1046A serdes fixes
- other minor fixes
Uboot prompt must not be available while running
secure boot. TO ensure this bootdelay must be set
to -2.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
fsl-mc lazyapply command applies dpl from efi_exit_boot_services().
Status of fsl-mc node in working fdt is updated at this stage.
However, an efi application like grub may already have copied the fdt.
So the updates to fdt done at efi_exit_boot_services() may not be
visible to the OS. Fix it by updating fdt earlier if fsl-mc lazyapply
command is used.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
when compiling dts file using DTC_FLAG='-@', the device tree compiler
reports these warnings:
Warning (alias_paths): /aliases: aliases property name must include
only lowercase and '-'
Fixed the node aliases to silence these warnings.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Change my email address, too many mails
gets to my private mail, created specific email
account just for developmement.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Now that various SPI related options depend on CONFIG_DEPRECATED, in
order for platforms to build out of the box they need to disable various
other options.
Cc: Albert ARIBAUD <albert.aribaud@3adev.fr>
Cc: Marek Vasut <marex@denx.de>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Per discussion on the list, drop this board again.
Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
- Add saveenv support for STM32MP1
- Add STM32MP1 Avenger96 board support
- Add SPI driver suport for STM32MP1
- Add watchdog support for STM32MP1
- Update power supply check via USB TYPE-C for STM32MP1 discovery board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2C9f
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20190606' of https://github.com/pchotard/u-boot
- Add Ethernet support for STM32MP1
- Add saveenv support for STM32MP1
- Add STM32MP1 Avenger96 board support
- Add SPI driver suport for STM32MP1
- Add watchdog support for STM32MP1
- Update power supply check via USB TYPE-C for STM32MP1 discovery board
Staticize 'spl_dram_init' and 'i2c_pad_info1' to fix the
following sparse warnings:
board/freescale/imx8mq_evk/spl.c:30:6: warning: symbol 'spl_dram_init' was not declared. Should it be static?
board/freescale/imx8mq_evk/spl.c:41:22: warning: symbol 'i2c_pad_info1' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Enable DM GPIO support on iMX6SX VINING|2000 and fix up
board code where applicable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
