Remove this file from git and instead build it using the Makefile.
With this change a few things need to be adjusted:
1. The 'notes' section no-longer appears at the start of the ELF file
(before the code), so update testSymbols to adjust the offsets.
2. The dynamic linker is disabled to avoid errors like:
"Not enough room for program headers, try linking with -N"
3. The interpreter note is moved to the end of the image, so that the
binman symbols appear first.
Signed-off-by: Simon Glass <sjg@chromium.org>
Remove this file from git and instead build it using the Makefile.
Update tools.GetInputFilename() to support reading files from an absolute
path, so that we can read the Elf test files easily. Also make sure that
the temp directory is report in ELF tests as this was commented out.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the ELF test files are checked into the U-Boot tree. This is
covenient since the files never change and can be used on non-x86
platforms. However it is not good practice to check in binaries and in
this case it does not seem essential.
Update the binman test-file Makefile to support having source in a
different directory. Adjust binman to run it to build bss_data, as a
start. We can add other files as needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
A Firmware Image Table (FIT) is a data structure defined by Intel which
contains information about various things needed by the SoC, such as
microcode.
Add support for this entry as well as the pointer to it. The contents of
FIT are fixed at present. Future work is needed to support adding
microcode, etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present binman has a single entry type for the 16-bit code code needed
to start up an x86 processor. This entry is intended to include both the
reset vector itself as well as the code to move to 32-bit mode.
However this is not very flexible since in some cases other data needs to
be included at the top of the SPI flash, in between these two pieces. For
example Intel requires that a FIT (Firmware Image Table) pointer be placed
0x40 bytes before the end of the ROM.
To deal with this, add a new reset entry for just the reset vector. A
subsequent change will adjust the existing 'start16' entry.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the Intel IFWI entry uses 'replace' without the 'ifwi-' prefix.
This is a fairly generic name which might conflict with the main Entry
base class at some point, if more features are added. Add a prefix.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a 'replace' command to binman to permit entries to be replaced, either
individually or all at once (using a filter).
Signed-off-by: Simon Glass <sjg@chromium.org>
At present binman cannot replace data within a CBFS since it does not
allow rewriting of the files in that CBFS. Implement this by using the
new WriteData() method to handle the case.
Add a header to compressed data so that the amount of compressed data can
be determined without reference to the size of the containing entry. This
allows the entry to be larger that the contents, without causing errors in
decompression. This is necessary to cope with a compressed device tree
being updated in such a way that it shrinks after the entry size is
already set (an obscure case). It is not used with CBFS since it has its
own metadata for this. Increase the number of passes allowed to resolve
the position of entries, to handle this case.
Add a test for this new logic.
Signed-off-by: Simon Glass <sjg@chromium.org>
The Intel descriptor must always appear at the start of an (x86) image,
so it is supposed to position itself there always. However there is no
explicit test for this. Add one and fix a bug introduced by the recent
change to adjust Entry to read the node in a separate call.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes an entry may shrink after it has already been packed. In that
case we must repack the items. Of course it is always possible to just
leave the entry at its original size and waste space at the end. This is
what binman does by default, since there is the possibility of the entry
changing size every time binman calculates its contents, thus causing a
loop.
Signed-off-by: Simon Glass <sjg@chromium.org>
So far we don't allow entries to change size when repacking. But this is
not very useful since it is common for entries to change size after an
updated binary is built, etc.
Add support for this, respecting the original offset/size/alignment
constraints of the image layout. For this to work the original image
must have been created with the 'allow-repack' property.
This does not support entry types with sub-entries such as files and
CBFS, but it does support sections.
Signed-off-by: Simon Glass <sjg@chromium.org>
The positioning does not currently work correctly if at the end of an
image with no fixed size. Also if the header is in the middle of an image
it can cause a gap in the image since the header position is normally at
the image end, so entries after it are placed after the end of the image.
Fix these problems and add more tests to cover these cases.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present it is not possible to discover the contraints to repacking an
image (e.g. maximum section size) since this information is not preserved
from the original image description.
Add new 'orig-offset' and 'orig-size' properties to hold this. Add them to
the main device tree in the image.
Signed-off-by: Simon Glass <sjg@chromium.org>
While it is useful and efficient to build images in a single pass from a
unified description, it is sometimes desirable to update the image later.
Add support for replace an existing file with one of the same size. This
avoids needing to repack the file. Support for more advanced updates will
come in future patches.
Signed-off-by: Simon Glass <sjg@chromium.org>
Current test coverage is likely sufficient for the logic used to place
sections in the image. However it seems useful to add a test specifically
for nested sections, since these could have some unusual interactions.
Add a new test for this and aligned sections. This test failed before the
refactor to drop the bsection.py file (Section class), but passes now.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is possible to read an Image, locate its FDT map and then read it into
the binman data structures. This allows full access to the entries that
were written to the image. Add support for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for locating an image's Fdt map which is used to determine
the contents and structure of the image.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is useful to be able to summarise all the entries in an image, e.g. to
display this to this user. Add a new ListEntries() method to Entry, and
set up a way to call it through the Image class.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is useful to add the CBFS file information (offset, size, etc.) into
the FDT so that the layout is complete. Add support for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the logic skips the blob class' handling of compression, so
this is not supported with device tree entries. Fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for detecting entries that change size after they have already
been packed, and re-running packing when it happens.
This removes the limitation that entry size cannot change after
PackEntries() is called.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is useful to be able to quickly locate the FDT map in the image. An
easy way to do this is with a pointer at the start or end of the image.
Add an 'image header' entry, which places a magic number followed by a
pointer to the FDT map. This can be located at the start or end of the
image, or at a chosen location.
As part of this, update GetSiblingImagePos() to detect missing siblings.
Signed-off-by: Simon Glass <sjg@chromium.org>
An FDT map is an entry which holds a full description of the image
entries, in FDT format. It can be discovered using the magic string at
its start. Tools can locate and read this entry to find out what entries
are in the image and where each entry is located.
Signed-off-by: Simon Glass <sjg@chromium.org>
A feature of CBFS is that it allows files to be positioned at particular
offset (as with binman in general). This is useful to support
execute-in-place (XIP) code, since this may not be relocatable.
Add a new cbfs-offset property to control this.
Signed-off-by: Simon Glass <sjg@chromium.org>
An Integrated Firmware Image is used to hold various binaries used for
booting with Apollolake and some later devices. Add support for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for putting CBFSs (Coreboot Filesystems) in an image. This
allows binman to produce firmware images used by coreboot to boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
We currenty support using the ELF file in U-Boot proper and SPL, but not
TPL. Add this as it is useful both with sandbox and for CBFS to allow
adding TPL as a 'stage'.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present text entries use an indirect method to specify the text to use,
with a label pointing to the text itself.
Allow the text to be directly written into the node. This is more
convenient in cases where the text is constant.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present sections are always placed automatically. Even if an 'offset'
property is provided it is ignored. Update the logic to support an offset
for sections.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Unfortunately the test was not included in the original implementation.
Add one.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
We now have 99 tests. Before adding any more, rename everything to three
digits. This helps to preserve the ordering of tests and makes it easier
to find things.
Signed-off-by: Simon Glass <sjg@chromium.org>
For sandbox we want to put ELF files in the image since that is what we
need to execute. Add support for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Normally x86 platforms use the end-at-4gb option. This currently produces
an FMAP with positions which have a large offset. The use of end-at-4gb is
a useful convenience within binman, but we don't really want to export
a map with these offsets.
Fix this by subtracting the 'skip at start' parameter.
Also put the code which convers names to fmap format, for clarity.
Signed-off-by: Simon Glass <sjg@chromium.org>
When TPL is used on x86 we may want to program the microcode (at least for
the first CPU) early in boot. Add support for this by refactoring the
existing code to be more generic.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimesi it us useful to be able to verify the content of entries with
a hash. Add an easy way to do this in binman. The hash information can be
retrieved from the device tree at run time.
Signed-off-by: Simon Glass <sjg@chromium.org>
In some cases it is useful to add a group of files to the image and be
able to access them at run-time. Of course it is possible to generate
the binman config file with a set of blobs each with a filename. But for
convenience, add an entry type which can do this.
Add required support (for adding nodes and string properties) into the
state module.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for compressing blob entries. This can help reduce image sizes
for many types of data. It requires that the firmware be able to
decompress the data at run-time.
Signed-off-by: Simon Glass <sjg@chromium.org>
Binman currently supports updating the main device tree with things like
the position of each entry. Extend this support to SPL and TPL as well,
since they may need (a subset of) this information.
Also adjust DTB output files to have a .out extension since this seems
clearer than having a .dtb extension with 'out' in the name somwhere.
Also add a few missing comments and update the DT setup code to use
ReadFile and WriteFile().
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes we want to include TPL for x86 platforms, such as when we want
to select between different SPL images (e.g. for Chrome OS verified boot).
Add support for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
This entry contains the PowerPC mpc85xx boot page and resetvec
sections.
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Currently binman calculates '_skip_at_start' based on 'end-at-4gb'
property and it is used for x86 images.
For PowerPC mpc85xx based CPU, CONFIG_SYS_TEXT_BASE is the entry
offset of the first entry. It can be 0xeff40000 or 0xfff40000 for
nor flash boot, 0x201000 for sd boot etc, so "_skip_at_start"
should be set to CONFIG_SYS_TEXT_BASE.
'end-at-4gb' property is not applicable where CONFIG_SYS_TEXT_BASE +
Image size != 4gb.
Add new property 'skip-at-start' in Section class so that
'_skip_at_start' can be calculated either based on 'end-at-4gb'
or based on "skip-at-start".
Add a test case to check that 'skip-at-start' and 'end-at-4gb'
property can't be used together.
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
This property has been changed to 'offset'. To help downstream users who
might still be using 'pos', add a check that this is not used by mistake.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for U-Boot's TPL and TPL device tree. Also fix a few comments
in the other device-tree entries.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is sometimes useful to have an area of the image which is all zeroes,
or all 0xff. This can often be achieved by padding the size of an an
existing entry and setting the pad byte for an entry or image.
But it is useful to have an explicit means of adding blocks of repeating
data to the image. Add a 'fill' entry type to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an entry type which can hold a Chrome OS EC.
To make this work a new entry type is created, which supports getting a
blob filename from the command line.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an entry which can hold an FMAP region as used by flashrom, an
open-source flashing tool used on Linux x86 machines. This provides a
simplified non-hierarchical view of the entries in the image and has a
signature at the start to allow flashrom to find it in the image.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is useful to able to write an identifying string to the image within an
entry. Add a 'text' entry type to handle this. The actual text is
typically passed to binman on the command line. The text is not itself
nul-terminated but this can be achieved if required by setting the size of
the entry to something larger than the text.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes it is useful to pass binman the value of an entry property from
the command line. For example some entries need access to files and it is
not always convenient to put these filenames in the image definition
(device tree).
Add a -a option which can be used like this:
-a<prop>=<value>
where
<prop> is the property to set
<value> is the value to set it to
Signed-off-by: Simon Glass <sjg@chromium.org>
At present each entry has an offset within its parent section. This is
useful for figuring out how entries relate to one another. However it
is sometimes necessary to locate an entry within an image, regardless
of which sections it is nested inside.
Add a new 'image-pos' property to provide this information. Also add
some documentation for the -u option binman provides, which updates the
device tree with final entry information.
Since the image position is a better symbol to use for the position of
U-Boot as obtained by SPL, update the SPL symbols to use this instead of
offset, which might be incorrect if hierarchical sections are used.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the .map file produced for each image does not include the
overall image size. This is useful information.
Update the code to generate it in the .map file as well as the updated
FDT. Also fix a few comments while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
After some thought, I believe there is an unfortunate naming flaw in
binman. Entries have a position and size, but now that we support
hierarchical sections it is unclear whether a position should be an
absolute position within the image, or a relative position within its
parent section.
At present 'position' actually means the relative position. This indicates
a need for an 'image position' for code that wants to find the location of
an entry without having to do calculations back through parents to
discover this image position.
A better name for the current 'position' or 'pos' is 'offset'. It is not
always an absolute position, but it is always an offset from its parent
offset.
It is unfortunate to rename this concept now, 18 months after binman was
introduced. However I believe it is the right thing to do. The impact is
mostly limited to binman itself and a few changes to in-tree users to
binman:
tegra
sunxi
x86
The change makes old binman definitions (e.g. downstream or out-of-tree)
incompatible if they use the 'pos = <...>' property. Later work will
adjust binman to generate an error when it is used.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is useful to write the position and size of each entry back to the
device tree so that U-Boot can access this at runtime. Add a feature to
support this, along with associated tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the contents of an entry are set in subclasses simply by
assigning to the data and content_size properties. Add some methods to do
this, so that we have more control. In particular, add a method to set the
contents without changing its size, so we can validate that case.
Add a test case for trying to change the size when this is not allowed.
Signed-off-by: Simon Glass <sjg@chromium.org>
This method is supposed to return the contents of an entry. However at
present there is no check that it actually does. Also some implementations
do not return 'True' to indicate success, as required.
Add a check for things working as expected, and correct the
implementations.
This requires some additional test cases to cover things which were missed
originally. Add these at the same time.
Signed-off-by: Simon Glass <sjg@chromium.org>
This fake entry is used for testing. At present it only has one behaviour
which is to return an invalid set of entry positions, to cause an error.
The fake entry will need to be used for other things too. Allow the test
.dts file to specify the behaviour of the fake entry, so we can control
its behaviour easily.
While we are here, drop the ReadContents() method, since this only applies
to subclasses of Entry_blob, which Entry__testing is not.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes we have several sections which repeat the same entries (e.g. for
a read-only and read-write version of the same section). It is useful to
be able to tell these entries apart by name.
Add a new 'name-prefix' property for sections, which causes all entries
within that section to have a given name prefix.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is useful to be able to split an image into multiple sections,
each with its own size and position, for cases where a flash device has
read-only and read-write portions.
Add support for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Allow the same binary to appear multiple times in an image by using the
device-tree unit-address feature (u-boot@0, u-boot@1).
Signed-off-by: Simon Glass <sjg@chromium.org>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
Binman construct images consisting of multiple binary files. These files
sometimes need to know (at run timme) where their peers are located. For
example, SPL may want to know where U-Boot is located in the image, so
that it can jump to U-Boot correctly on boot.
In general the positions where the binaries end up after binman has
finished packing them cannot be known at compile time. One reason for
this is that binman does not know the size of the binaries until
everything is compiled, linked and converted to binaries with objcopy.
To make this work, we add a feature to binman which checks each binary
for symbol names starting with '_binman'. These are then decoded to figure
out which entry and property they refer to. Then binman writes the value
of this symbol into the appropriate binary. With this, the symbol will
have the correct value at run time.
Macros are used to make this easier to use. As an example, this declares
a symbol that will access the 'u-boot-spl' entry to find the 'pos' value
(i.e. the position of SPL in the image):
binman_sym_declare(unsigned long, u_boot_spl, pos);
This converts to a symbol called '_binman_u_boot_spl_prop_pos' in any
binary that includes it. Binman then updates the value in that binary,
ensuring that it can be accessed at runtime with:
ulong u_boot_pos = binman_sym(ulong, u_boot_spl, pos);
This assigns the variable u_boot_pos to the position of SPL in the image.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is only 3 bytes long which is not enough to hold two symbol values,
needed to test the binman symbols feature. Increase it to 15 bytes.
Using very small regions is useful since we can easily compare them in
tests and errors are fairly easy to diagnose.
Signed-off-by: Simon Glass <sjg@chromium.org>
For testing we need to build some ELF files containing binman symbols. Add
these to the Makefile and check in the binaries:
u_boot_binman_syms - normal, valid ELF file
u_boot_binman_syms_bad - missing the __image_copy_start symbol
u_boot_binman_syms_size - has a binman symbol with an invalid size
Signed-off-by: Simon Glass <sjg@chromium.org>
In some cases we need to read symbols from U-Boot. At present we have a
a few cases which does this via 'nm' and 'grep'.
It is better to use objdump since that tells us the size of the symbols
and also whether it is weak or not.
Add a new module which reads ELF information from files. Update existing
uses of 'nm' to use this module.
Signed-off-by: Simon Glass <sjg@chromium.org>
MRC (Memory Reference Code) is a binary blob used to set up the SDRAM
controller on some Intel boards. Add a test for this feature.
With this test coverage on binman is back up to 100%.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a test for this feature. It allows SPL to hold a pointer to the
microcode block. This is used for 64-bit U-Boot on x86.
Signed-off-by: Simon Glass <sjg@chromium.org>
These test programs are includedd as binary files in U-Boot to avoid
having to build them (and associated toolchain differences). Instructions
on building are in the files themselves, but it seems better to provide
a Makefile which can be manually run when desired.
Add a Makefile, separate from the normal build system, to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
The tests don't currently cover all the different property types. Add a
new test which checks each property type in turn, to make sure each has
the correct type and value.
Signed-off-by: Simon Glass <sjg@chromium.org>
With recent changes, some x86-specific rom tests of binman fail to
run. Fix it by adding missing filenames in corresponding entries.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for two more from the inexhaustible supply of x86 binary blob
types.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
When building for 64-bit x86 we need an SPL binary in the ROM. Add support
for this. Also increase entry test code coverage to 100%.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Add an entry type for u-boot.img (a legacy U-Boot image) and a simple test.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
The structure of x86 ROMs is pretty complex. There are various binary blobs
to place in the image. Microcode requires special handling so that it is
available to very early code and can be used without any memory whatsoever.
Add support for the various entry types that are currently needed, along
with some tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Add entries to support some standard U-Boot binaries, such as u-boot.bin,
u-boot.dtb, etc. Also add some tests for these.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
