This function is already defined in spi.h but no implementation of it
currently exists in the tree. The implementation is based on the static
function spi_set_speed_mode(). The function prototype is modified so
that an success or error condition can be returned to the caller.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Fix typo that was caused by the same feature being split in to 2 different
configuration options. Replace CONFIG_USBNET_DEVADDR with
CONFIG_USBNET_DEV_ADDR
Signed-off-by: Ignacio Zamora <nachopitt@gmail.com>
Putting these definitions in a header will allow signatures to be
validated independently of bootm.
Signed-off-by: Steven Lawrance <steven.lawrance@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In drivers usb/host/{ehci,ohci}-generic.c, {ehci,ohci}_setup_phy() and
{ehci,ohci}_shutdown_phy() shares 95% of common code.
Factorize this code in new generic_{setup,shudown}_phy() functions.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Allow avoiding using EFI_CALL() when closing a protocol by providing an
internal function.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This function is only used inside efi_boottime.c and is not safe to use
outside of this context.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
- mtd: Update the function name to 'rfree'
- Support NAND ONFI EDO mode for imx8mn architecture
- dm: clk: add missing stub when CONFIG_CLK is deactivated
-----BEGIN PGP SIGNATURE-----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=VPkV
-----END PGP SIGNATURE-----
Merge tag 'u-boot-nand-20221009' of https://source.denx.de/u-boot/custodians/u-boot-nand-flash
- mtd: Update the function name to 'rfree'
- Support NAND ONFI EDO mode for imx8mn architecture
- dm: clk: add missing stub when CONFIG_CLK is deactivated
Since commit 8d38a8459b ("mtd: Rename free() to rfree()")
the function has been renamed to rfree(), so update the description
inside the mtd_oob_region structure as well.
Fixes: 8d38a8459b ("mtd: Rename free() to rfree()")
Reported-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Add support for imx8mn architecture in order to run the NAND
in fast edo mode.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Add missing stub for functions [devm_]clk_...() when CONFIG_CLK is
deactivated.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
In order to move ppc-specific code out of setup_dest_addr(), provide an
arch-specific variant arch_setup_dest_addr(), that can be used by
architecture code to fix up the initial reloc address.
It is called at the end of setup_dest_addr() initcall and the default
implementation is a nop stub.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
A following patch is cleaning up the core EFI code trying to remove
sequences of efi_create_handle, efi_add_protocol.
Although this works fine there's a problem with the latter since it is
usually combined with efi_delete_handle() which blindly removes all
protocols on a handle and deletes the handle. We should try to adhere to
the EFI spec which only deletes a handle if the last instance of a protocol
has been removed. Another problem is that efi_delete_handle() never checks
for opened protocols, but the EFI spec defines that the caller is
responsible for ensuring that there are no references to a protocol
interface that is going to be removed.
So let's fix this by replacing all callsites of
efi_create_handle(), efi_add_protocol() , efi_delete_handle() with
Install/UninstallMultipleProtocol.
In order to do that redefine functions that can be used by the U-Boot
proper internally and add '_ext' variants that will be used from the
EFI API
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Move the registration of events for the addition and removal of block
devices to the block device driver. Here we can add a reference to the
EFI Driver Binding protocol as context.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
For handling added and removed block devices we need to register events
which has to be done when the driver is installed.
This patch only creates an empty init function that will be filled with
code later on. The function needs to be called before any EFI block devices
are used. Move the efi_driver_init() call to early init.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
DisconnectController() is based on the open protocol information created
when the driver opens a protocol with BY_CHILD_CONTROLLER or BY_DRIVER.
To create an open protocol information it is required to supply the handle
of the driver as agent handle. This information is available as field
DriverBindingHandle in the driver binding protocol.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
* Convert code comments in include/efi_driver.h to Sphinx style.
* Add include/efi_driver.h to the HTML documentation.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
If creating the block device fails,
* delete all created objects and references
* close the protocol interface on the controller
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
When deleting a device or a handle we must remove the link between the two
to avoid dangling references.
Provide function efi_unlink_dev() for this purpose.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
These boards are out of maintenance and can be removed.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
Reviewed-by: Stefan Roese <sr@denx.de>
For future DM based FPGA drivers and for now to have a meaningful
logging class for old FPGA drivers.
Suggested-by: Michal Simek <michal.simek@amd.com>
Suggested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Dahl <post@lespocky.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20220930120430.42307-2-post@lespocky.de
Signed-off-by: Michal Simek <michal.simek@amd.com>
At present ofnode_write_prop() is inconsistent between livetree and
flattree, in that livetree requires the caller to ensure the property
value is stable (e.g. in rodata or allocated) but flattree does not, since
it makes a copy.
This makes the API call a bit painful to use, since the caller must do
different things depending on OF_LIVE.
Add a new 'copy' argument which tells the function to make a copy if
needed. Add some tests to cover this behaviour.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some ofnode functions can only operate on the default device tree, i.e.
U-Boot's control FDT. Add comments to that effect. Fix up the reference to
device tree bindings while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
We need to be able to look up phandles in any FDT, not just the control
FDT. Use the 'other' FDT to test this, with a helper function which gets
this as an oftree that can then we used as needed.
Add a few more tests and some comments at the top of the file, to explain
what is going on.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add the logic to redirect requests for the device tree through a function
which can look up the tree ID. This works by using the top bits of
ofnode.of_offset to encode a tree.
It is assumed that there will only be a few device trees used at runtime,
typically the control FDT (always tree ID 0) and possibly a separate FDT
to be passed the OS.
The maximum number of device trees supported at runtime is 8, with this
implementation. That would use bits 30:28 of the node-offset value,
meaning that the positive offset range is limited to bits 27:0, versus
30:1 with this feature disabled. That still allows a device tree of up
to 256MB, which should be enough for most FITs. Larger ones can be
supported by using external data with the FIT, or by enabling OF_LIVE.
Update the documentation a little and fix up the comment for
ofnode_valid().
Signed-off-by: Simon Glass <sjg@chromium.org>
At present, unless OF_LIVE is enabled, ofnode only supports access to one
device tree, the control FDT. This is because only the node offset is
encoded in ofnode, with the tree being implicit.
This makes ofnode (without OF_LIVE) unsuitable for device tree fixups, as
implemented by ft_board_setup() and other such functions.
To solve this, we can use the top bits of the node offset to hold a tree
ID.
Add the definitions for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function turns out to be a little confusing since it looks up a path
and also registers the tree. Split it into two, one that gets the root
node and one that looks up a path, so the purpose is clear.
Registering the tree will happen in a function to be added in a later
patch, called oftree_from_fdt().
Signed-off-by: Simon Glass <sjg@chromium.org>
In some cases we want to obtain an ofnode in the same tree as a different
ofnode, such as when looking up a subnode. At present this is trivial,
since there is only one tree. When there are multiple trees, this
implementation will change.
Also move the ofnode_to_offset() function up higher in the header file,
since we will need to provide a different implementation with multiple
trees.
Signed-off-by: Simon Glass <sjg@chromium.org>
When we have multiple trees, the ofnode logic needs to be told which one
to use. Create a new function which takes an oftree argument, along with
a helper to obtain the FDT pointer from an oftree.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present dm_test_ofnode_root() does this manually. Add some inline
functions to handle it, so this code can be centralised.
Add oftree functions to produce a null tree and to check whether a tree
is valid or not.
Signed-off-by: Simon Glass <sjg@chromium.org>
The flat device tree is assumed to be the control FDT but this is not
always the case. Update the ofnode implementation to obtain the node via
an function call so we can eventually add support for selecting different
trees.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present there is only one device tree used by the ofnode functions,
except for some esoteric use of live tree. In preparation for supporting
more than one, add a way to reset the list of device trees.
For now this does nothing.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current tests do not cover all the behaviour. Add some more.
Tidy up a few inconsistencies between livetree and flattree which come to
light with these tests. Also drop the -ENODATA error since it is never
actually returned.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current implementation creates a 'name' value for every node. This
is not needed for the latest device tree format, which includes a name in
the node header.
Adjust the code to point the name at the node header instead.
Also simplify ofnode_get_name(), now that we can rely on it to set the
name correctly. Update the comment to make it clear what name the root
node has.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current name is quite unwieldy. Change it to use an ofprop_ prefix
and shorten it. Fix the return-value comment while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update the function to mark it with the const attribute. Also avoid
calling it multiple times in the devfdt_get_addr_index() function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a test flag which indicates that the 'other' FDT should be set up
ready for use. Handle this by copying in the FDT, unflattening it for
livetree tests. Free the structures when the tests have run.
We cannot use the other FDT unless we are using live tree or
OFNODE_MULTI_TREE is enabled, since only one tree is supported by the
ofnode interface in that case. Add this condition into
ut_run_test_live_flat() and update the comments.
Signed-off-by: Simon Glass <sjg@chromium.org>
Provide a way to copy over the 'other' FDT when running tests. This loads
it and allocates memory for the copy, if not done already, then does the
copy.
Avoid using U-Boot's malloc() pool for these copies, at least for now,
since they are part of the test system.
Tidy up the cpu.c header files while here.
Signed-off-by: Simon Glass <sjg@chromium.org>
This was a workaround for a rare situation. Now that it will be more
common and we have a proper fix, drop the flag. We can run both types of
tests in the same sandbox executable, even if the flat device tree is
modified.
Signed-off-by: Simon Glass <sjg@chromium.org>
If the device tree changes during a test and we cannot restore it, mark
it as such so that future tests which need the live tree are skipped.
Signed-off-by: Simon Glass <sjg@chromium.org>
When the flat device tree changes it can mess up the live tree since that
uses the flat tree for its strings. This affects only a few sandbox tests
which modify the device tree, but the number will grow as ofnode support
for writing improves.
While the control FDT is not intended to change while U-Boot is running,
some tests do so. For example, the ofnode interface only supports
modifying properties in the control FDT, so tests must use that.
To solve this problem, keep a copy of the FDT and restore it as needed
when the test is finished. The copy only happens on sandbox (except SPL
builds), to reduce memory usage and because these tests are not useful on
other boards. For other boards, a checksum is taken to ensure that nothing
changes.
It would be possible to always checksum the FDT on sandbox and only
restore it if needed, but this is slightly slower than restoring it every
time, at least with crc8.
Move the code which checks for success to the very end, for clarity.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that we support writing to ofnodes, the const is not accurate. Drop
it to avoid undesirable casting.
Also drop the ofnode_to_npw() which is now the same as ofnode_to_np().
Signed-off-by: Simon Glass <sjg@chromium.org>
Add this feature to the ofnode interface, supporting both livetree and
flattree. If the node exists it is returned, along with a -EEXIST error.
Update the functions it calls to handle this too.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is helpful to test that out-of-memory checks work correctly in code
that calls malloc().
Add a simple way to force failure after a given number of malloc() calls.
Fix a header guard to avoid a build error on sandbox_vpl.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
At present the live tree tests are not run on sandbox. This bug is in two
parts, with a duplicate flag value and incorrect logic in the test runner.
This was not noticed because the bug was fixed in a later commit and does
not cause test failures.
Fix this.
Fixes: 7b1dfc9fd7 ("dm: core: Prepare for updating the device tree with ofnode")
Signed-off-by: Simon Glass <sjg@chromium.org>
This function currently assumes that the control FDT is used. Update it
to allow a root node to be passed, so it can work with any tree.
Also add a comment to ofnode_get_by_phandle() so that its purpose is
clear.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present only one spy is allowed per event. Update the naming to allow
more than one, since some need this flexibility, e.g. the EVT_FT_FIXUP
event.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is not needed and we should avoid typedefs. Use the struct instead
and rename it to indicate that it really is a legacy struct.
Signed-off-by: Simon Glass <sjg@chromium.org>
- SPL fixes for STM32F7 MCUs
- Device tree alignement with kernelv6.0-rc4 for MCU's board
- Device tree alignement with kernelv6.0-rc3 for MPU's board
- Update DDR node for STM32MP15
- Cleanup config file for STM32MP1
- Update for cmd_stm32key command
- Fix compatible string to add partitions for STM32MP1
- Update for stm32programmer tool
-----BEGIN PGP SIGNATURE-----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=iA80
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220927' of https://source.denx.de/u-boot/custodians/u-boot-stm into next
- Increase SYS_MALLOC_F_LEN for STM32 MCU's board
- SPL fixes for STM32F7 MCUs
- Device tree alignement with kernelv6.0-rc4 for MCU's board
- Device tree alignement with kernelv6.0-rc3 for MPU's board
- Update DDR node for STM32MP15
- Cleanup config file for STM32MP1
- Update for cmd_stm32key command
- Fix compatible string to add partitions for STM32MP1
- Update for stm32programmer tool
xilinx:
- Add support for new Versal NET SOC
zynqmp:
- Use mdio bus for ethernet phy description
- Wire ethernet phy reset via i2c-gpio
versal:
- Config cleanup
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYzGwogAKCRDKSWXLKUoM
Ial4AJ9+4WHn0MV2X7gK1fyh4lUW7ggPhQCggsYlSoACgMgdji17SAPhCv/W3IA=
=BmA9
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2023.01-rc1-v2' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2023.01-rc1 (round 2)
xilinx:
- Add support for new Versal NET SOC
zynqmp:
- Use mdio bus for ethernet phy description
- Wire ethernet phy reset via i2c-gpio
versal:
- Config cleanup
By pressing "c" key during SPL execution, we force U-boot execution
instead of a kernel XIP image.
This fixes a hard fault when booting stm32f746-disco in SPL with "c"
key pressed during SPL execution.
U-Boot SPL 2022.10-rc5-00009-g40d02baa91 (Sep 20 2022 - 17:21:21 +0200)
Trying to boot from XIP
Hard fault
pc : 080083fc lr : 08000d1b xPSR : 21000000
r12 : 2004f108 r3 : 080083fd r2 : 00000028
r1 : 2004f0c8 r0 : 2004f0e4
Resetting CPU ...
This is due to SYS_UBOOT_START flag set to 0x080083FD which is not correct.
If unset, SYS_UBOOT_START is set by default to CONFIG_SYS_TEXT_BASE
which match with our requirement.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Tested-by: Waldemar Brodkorb <wbx@openadk.org>
Versal NET platform is based on Versal chip which is reusing a lot of IPs.
For more information about new IPs please take a look at DT which describe
currently supported devices.
The patch is adding architecture and board support with soc detection
algorithm. Generic setting should be very similar to Versal but it will
likely diverge in longer run.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/320206853dc370ce290a4e7b6d0bb26b05206021.1663589964.git.michal.simek@amd.com
In preparation for sharing the emulation code between two drivers, move
some of the fields into a new struct. Use a separate header file so it
can be used by various drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Like in all other console functions, implement also serial_flush() function
as a fallback int console flush() function.
Flush support is available only when config option CONSOLE_FLUSH_SUPPORT is
enabled. So when it is disabled then provides just empty static inline
function serial_flush().
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
On certain places it is required to flush output print buffers to ensure
that text strings were sent to console or serial devices. For example when
printing message that U-Boot is going to boot kernel or when U-Boot is
going to change baudrate of terminal device.
Therefore introduce a new flush() and fflush() functions into console code.
These functions will call .flush callback of associated stdio_dev device.
As this function may increase U-Boot side, allow to compile U-Boot without
this function. For this purpose there is a new config CONSOLE_FLUSH_SUPPORT
which is enabled by default and can be disabled. It is a good idea to have
this option enabled for all boards which have enough space for it.
When option is disabled when U-Boot defines just empty static inline
function fflush() to avoid ifdefs in other code.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit 37dc958947 ("global_data.h: Change ram_top type to phys_addr_t")
changed type of ram_top member from ulong to phys_addr_t but did not
changed types in board_get_usable_ram_top() function which returns value
for ram_top.
So change ulong to phys_addr_t type also in board_get_usable_ram_top()
signature and implementations.
Fixes: 37dc958947 ("global_data.h: Change ram_top type to phys_addr_t")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds clock driver support for MediaTek MT7981 SoC
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds clock driver support for MediaTek MT7986 SoC
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds a pinctrl header for common pinconf parameters such as
pull-up/pull-down resistors and drive strengths.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds general board files based on MT7981 SoCs.
MT7981 uses one mmc controller for booting from both SD and eMMC, and the
pins of mmc controller are also shared with spi controller.
So three configs are need for these boot types:
1. mt7981_rfb_defconfig - SPI-NOR and SPI-NAND
2. mt7981_emmc_rfb_defconfig - eMMC only
3. mt7981_sd_rfb_defconfig - SD only
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Add general board files based on MT7986 SoCs.
MT7986 uses one mmc controller for booting from both SD and eMMC.
Both MT7986A and MT7986B use the same pins for spi controller.
Configs for various boot types:
1. mt7986_rfb_defconfig - SPI-NOR and SPI-NAND for MT7986A/B
2. mt7986a_bpir3_emmc_defconfig - eMMC for MT7986A only
3. mt7986a_bpir3_sd_defconfig - SD for MT7986A only
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Remove the unnecessary comment after the CONFIG_SYS_BOOTM_LEN
migration to Kconfig.
Fixes: c45568cc4e ("Convert CONFIG_SYS_BOOTM_LEN to Kconfig")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This driver is not used by any system and is long unmaintained, drop it.
There is a DWC2 OTG driver which is maintained, see CONFIG_USB_GADGET_DWC2_OTG .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Update the distro config env memory layout for the Verdin iMX8M Mini and
Verdin iMX8M Plus:
- loadaddr=0x48280000 allows for 128.5MB area for uncompressing (ie FIT
images, kernel_comp_addr_r, kernel_comp_size)
- fdt_addr_r = loadaddr + 127.5MB : allows for 127.5MB kernel
- scriptaddr = fdt_addr_r + 512KB : allows for 512KB fdt
- ramdisk_addr_r = scriptaddr + 512KB : allows for 512KB script
Memory layout taken from commit fd5c7173ad
("imx8m{m,n}_venice: update env memory layout") but moved loadaddr by an
additional 0.5MB to avoid "Moving Image from 0x48200000 to 0x48280000"
during booti plus actually defining kernel_comp_size to make booti work.
Note that for our regular BSP Layers and Reference Images for Yocto
Project an updated distro boot script is required (see
meta-toradex-bsp-common/recipes-bsp/u-boot/u-boot-distro-boot).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Erase the entire U-Boot area during U-Boot update instead of just
a subset of it. This way, in case u-boot-with-spl.imx grows, the
sf write won't write over non-erased part of the SPI NOR.
Signed-off-by: Marek Vasut <marex@denx.de>
The i.MXRT11 series has different offsets for IOCR_MUX, it also can
address 64MiB of SDRAM so add a macro for that.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Remove some now unused macros and #ifdef's.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
Now that we've globally replaced all WATCHDOG_RESET occurances, let's
remove the ugly macro itself in the header.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
Only one occurance of WATCHDOG_RESET is left in one assembler file.
This patch changes this occurance to a direct call to watchdog_reset
and then removes all the ASSEMBLY ifdef'ery in watchdog.h, as it's not
needed any more to clean this mess a bit up.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Tom Rini <trini@konsulko.com> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
Globally replace all occurances of WATCHDOG_RESET() with schedule(),
which handles the HW_WATCHDOG functionality and the cyclic
infrastructure.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
This patch introduces a schedule() function, which shall be used instead
of the old WATCHDOG_RESET. Follow-up patches will make sure, that this
new function is used.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
We currently have an if_type (interface type) and a uclass id. These are
closely related and we don't need to have both.
Drop the if_type values and use the uclass ones instead.
Maintain the existing, subtle, one-way conversion between UCLASS_USB and
UCLASS_MASS_STORAGE for now, and add a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
This doesn't seem to be used for anything and it isn't clear what it is.
It dates from the first U-Boot commit.
Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
This option is fact really related to SPL. For U-Boot proper we always use
driver model for block devices, so CONFIG_BLK is enabled if block devices
are in use.
It is only for SPL that we have two cases:
- SPL_BLK is enabled, in which case we use driver model and blk-uclass.c
- SPL_BLK is not enabled, in which case (if we need block devices) we must
use blk_legacy.c
Rename the symbol to SPL_LEGACY_BLOCK to make this clear. This is
different enough from BLK and SPL_BLK that there should be no confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we use HAVE_BLOCK_DEVICE to indicate when block devices are
available.
This is a very strange option, since it partially duplicates the BLK
option used by driver model. It also covers both U-Boot proper and SPL,
even though one might have block devices and another not.
As a first step towards correcting this, create a new inline function
called blk_enabled() which indicates if block devices are available.
This cannot be used in Makefiles, or #if clauses, but can be used in C
code.
A function is useful because we cannot use CONFIG_IS_ENABLED(BLK) to
decide if block devices are needed, since we must consider the legacy
block interface, enabled by HAVE_BLOCK_DEVICE
Update a few places where it can be used and drop some unnecessary #if
checks around some functions in disk/part.c - rely on the compiler's
dead-code elimination instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
* Drop legacy /boot/PPTImage.md5 check
* Update device tree naming
* Update t30args#0 root cmd line property to support latest kernel
versions (root=/dev/mmcblk0p2 for linux < 4 and
root=/dev/mmcblk1p2 for linux >= 4)
* Add custom bootloader version string
* Destroy invalid dtb at ${dtbaddr} and configuration script at
${cfgaddr} to ensure proper boot in warm restart case.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Commit 0ea4fc4dcf ("board/BuR: invalidate ${dtbaddr} before cfgscr")
destroys the boot targets b_t30lgcy#0 and b_t30lgcy#1. The reason behind
this is, that b_t30lgcy#0 and b_t30lgcy#1 both load the for booting
needed device trees from mmc and the cfgscr script patches those. Because
of this, cfgscr is not allowed to destroy the previously loaded device
tree otherwise cfgscr will fail.
This patch moves the device trees invalidation on warm restart to the
PREBOOT cmd to fix that issue.
Fixes: 0ea4fc4dcf ("board/BuR: invalidate ${dtbaddr} before cfgscr")
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
The SPI and NAND board variants never went into production.
Drop those board variants.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
This allows to test if a pin's label if displayed using gpio_get_status()
when this pin is configured in alternate function.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This change defines resources for OP-TEE service drivers to register
themselves for being bound to when OP-TEE firmware reports the related
service is supported. OP-TEE services are discovered during optee
driver probe sequence which mandates optee driver is always probe once
bound.
Discovery of optee services and binding to related U-Boot drivers is
embedded upon configuration switch CONFIG_OPTEE_SERVICE_DISCOVERY.
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add functions to read 8/16-bit integers like the existing functions for
32/64-bit to simplify read of 8/16-bit integers from device tree
properties.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
UEFI:
Implement a command eficonfig to maintain Load Options and boot order via
menus.
-----BEGIN PGP SIGNATURE-----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=P89S
-----END PGP SIGNATURE-----
Merge tag 'efi-next-2022-09-14' of https://source.denx.de/u-boot/custodians/u-boot-efi into next
Pull request for efi next
UEFI:
Implement a command eficonfig to maintain Load Options and boot order via
menus.
Remove all but a few that are difficult, relying on legacy CONFIG options
or optional global_data fields.
Drop the duplicate function name in the comment for boot_get_cmdline().
Signed-off-by: Simon Glass <sjg@chromium.org>
UEFI specification requires booting from removal media using
a architecture-specific default image name such as BOOTAA64.EFI.
This commit adds the removable media entries into bootmenu,
so that user can select the removable media and boot with
default image.
The bootmenu automatically enumerates the possible bootable
media devices supporting EFI_SIMPLE_FILE_SYSTEM_PROTOCOL,
add it as new UEFI boot option(BOOT####) and update BootOrder
variable. This automatically generated UEFI boot option
has the dedicated guid in the optional_data to distinguish it from
the UEFI boot option user adds manually. This optional_data is
removed when the efi bootmgr loads the selected UEFI boot option.
This commit also provides the BOOT#### variable maintenance feature.
Depending on the system hardware setup, some devices
may not exist at a later system boot, so bootmenu checks the
available device in each bootmenu invocation and automatically
removes the BOOT#### variable corrensponding to the non-existent
media device.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
This is preparation to support menu-driven UEFI BootOrder
variable updated by KEY_PLUS, KEY_MINUS and KEY_SPACE.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This commit adds the menu entry to edit the existing
BOOT#### variable contents.
User selects the item from the boot option list, then
user can edit the description, file path and optional_data.
Note that automatically generated boot option entry by bootmenu
to support the removable media device is filtered out and user
can not edit the automatically generated entry.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
This commit add the "eficonfig" command.
The "eficonfig" command implements the menu-driven UEFI boot option
maintenance feature. This commit implements the addition of
new boot option. User can select the block device volume having
efi_simple_file_system_protocol and select the file corresponding
to the Boot#### variable. User can also enter the description and
optional_data of the BOOT#### variable in utf8.
This commit adds "include/efi_config.h", it contains the common
definition to be used from other menus such as UEFI Secure Boot
key management.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
This patch integrates the main function responsible for calling all
registered cyclic functions cyclic_run() into the common WATCHDOG_RESET
macro. This guarantees that cyclic_run() is executed very often, which
is necessary for the cyclic functions to get scheduled and executed at
their configured periods.
If CONFIG_WATCHDOG is not enabled, only cyclic_run() without calling
watchdog_reset(). This guarantees that the cyclic functionality does not
rely on CONFIG_WATCHDOG being enabled.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the basic infrastructure to periodically execute code, e.g. all
100ms. Examples for such functions might be LED blinking etc. The
functions that are hooked into this cyclic list should be small timewise
as otherwise the execution of the other code that relies on a high
frequent polling (e.g. UART rx char ready check) might be delayed too
much. This patch also adds the Kconfig option
CONFIG_CYCLIC_MAX_CPU_TIME_US, which configures the max allowed time
for such a cyclic function. If it's execution time exceeds this time,
this cyclic function will get removed from the cyclic list.
How is this cyclic functionality executed?
The following patch integrates the main function responsible for
calling all registered cyclic functions cyclic_run() into the
common WATCHDOG_RESET macro. This guarantees that cyclic_run() is
executed very often, which is necessary for the cyclic functions to
get scheduled and executed at their configured periods.
This cyclic infrastructure will be used by a board specific function on
the NIC23 MIPS Octeon board, which needs to check periodically, if a
PCIe FLR has occurred.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
When using us times it makes sense to use 64bit variables for storage.
The currently implemented time_after() and friends functions only handle
32bit variables. This patch now includes the 64bit variants as well
from Linux. This will be used by the upcoming generic cyclic function
infrastructure.
These macros were copied from include/linux/jiffies.h of Linux 5.18.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds support for the dirmap API to the spi-nor subsystem, as
introduced in Linux commit df5c21002cf4 ("mtd: spi-nor: use
spi-mem dirmap API").
This patch is synchronize from the following patch
https://patchwork.ozlabs.org/project/uboot/patch/20210205043924.149504-4-seanga2@gmail.com/
The corresponding Linux kernel SHA1 is df5c21002cf4.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
This adds the dirmap API originally introduced in
Linux commit aa167f3fed0c
("spi: spi-mem: Add a new API to support direct mapping").
This also includes several follow-up patches and fixes.
Changes from Linux include:
* Added Kconfig option
* Changed struct device to struct udevice
* Changed struct spi_mem to struct spi_slave
This patch is obtained from the following patch
https://patchwork.ozlabs.org/project/uboot/patch/20210205043924.149504-3-seanga2@gmail.com/
The corresponding Linux kernel SHA1 is aa167f3fed0c.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Add bdinfo_print_size() helper to display size variables (such as cache
sizes) in bdinfo format. The size is printed as "xxx Bytes", "xxx KiB",
"xxx MiB", "xxx GiB", etc as needed;
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Reviewed-by: Jason Liu <jason.hui.liu@nxp.com>
Link: https://lore.kernel.org/r/20220829170205.1274484-3-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
These macros are not used anymore in microblaze code since commit
f113d7d303 ("Convert CONFIG_SPL_STACK to Kconfig"), so remove them.
Fixes: f113d7d303 ("Convert CONFIG_SPL_STACK to Kconfig")
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220829170205.1274484-1-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
$fdt_addr is mandatory for systems which provides DTB in HW (e.g. ROM) and
wishes to pass that DTB to Linux.
Turris Mox contains DTB binary in SPI NOR memory at "dtb" partition which
starts at offset 0x7f0000 and is 0x10000 bytes long.
Armada 3700 CPU does not allow mapping SPI NOR memory into physical address
space like on other architectures and therefore set $fdt_addr variable to
memory range in RAM and loads this DTB binary from SPI NOR in misc_init_r()
function.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
A recurring theme on LKML is the boot process deadlocking due to some
process blocking waiting for random numbers, while the kernel's
Cryptographic Random Number Generator (crng) is not initalized yet,
but that very blocking means no activity happens that would generate
the entropy necessary to finalize seeding the crng.
This is not a problem on boards that have a good hwrng (when the
kernel is configured to trust it), whether in the CPU or in a TPM or
elsewhere. However, that's far from all boards out there. Moreover,
there are consumers in the kernel that try to obtain random numbers
very early, before the kernel has had any chance to initialize any
hwrng or other peripherals.
Allow a board to provide a board_rng_seed() function, which is
responsible for providing a value to be put into the rng-seed property
under the /chosen node.
The board code is responsible for how to actually obtain those
bytes.
- One possibility is for the board to load a seed "file" from
somewhere (it need not be a file in a filesystem of course), and
then ensure that that the same seed file does not get used on
subsequent boots.
* One way to do that is to delete the file, or otherwise mark it as
invalid, then rely on userspace to create a new one, and living
with the possibility of not finding a seed file during some boots.
* Another is to use the scheme used by systemd-boot and create a new
seed file immediately, but in a way that the seed passed to the
kernel and the new (i.e. next) seed cannot be deduced from each
other, see the explanation at
https://lore.kernel.org/lkml/20190929090512.GB13049@gardel-login/
and the current code at
https://github.com/systemd/systemd/blob/main/src/boot/efi/random-seed.c
- The board may have an hwrng from which some bytes can be read; while
the kernel can also do that, doing it in U-Boot and providing a seed
ensures that even very early users in the kernel get good random
numbers.
- If the board has a sensor of some sort (temperature, humidity, GPS,
RTC, whatever), mixing in a reading of that doesn't hurt.
- etc. etc.
These can of course be combined.
The rng-seed property is mixed into the pool used by the linux
kernel's CRNG very early during boot. Whether it then actually
contributes towards the kernel considering the CRNG initialized
depends on whether the kernel has been configured with
CONFIG_RANDOM_TRUST_BOOTLOADER (nowadays overridable via the
random.trust_bootloader command line option). But that's for the BSP
developer to ultimately decide.
So, if the board needs to have all that logic, why not also just have
it do the actual population of /chosen/rng-seed in ft_board_setup(),
which is not that many extra lines of code?
I considered that, but decided handling this logically belongs in
fdt_chosen(). Also, apart from saving the board code from the few
lines of boilerplate, doing it in ft_board_setup() is too late for at
least some use cases. For example, I want to allow the board logic to
decide
ok, let's pass back this buffer and use that as seed, but also let's
set random.trust_bootloader=n so no entropy is credited.
This requires the rng-seed handling to happen before bootargs
handling. For example, during the very first boot, the board might not
have a proper seed file, but the board could still return (a hash of)
some CPU serial# or whatnot, so that at least no two boards ever get
the same seed - the kernel always mixes in the value passed in
rng-seed, but if it is not "trusted", the kernel would still go
through the same motions as it would if no rng-seed was passed before
considering its CRNG initialized. I.e., by returning that
unique-to-this-board value and setting random.trust_bootloader=n, the
board would be no worse off than if board_rng_seed() returned nothing
at all.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
We can use efi_st_get_config_table() in multiple unit tests.
Export the function.
Export system-table and boot-services.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
- remove test on CONFIG_DM_REGULATOR in stm32mp1 board
and enable CONFIG_DM_REGULATOR for stm32f769-disco
- handle ck_usbo_48m clock provided by USBPHYC to fix the command 'usb start'
after alignment with Linux kernel v5.19 DT (clocks = <&usbphyc>)
- Fix SYS_HZ_CLOCK value for stih410-b2260 board
- Switch STMM32MP15x DHSOM to FMC2 EBI driver
- Remove hwlocks from pinctrl in STM32MP15x to avoid issue with kernel
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAmMZoW4ACgkQ4rK92eCq
k3W2MAgAsmy2aSlMYo/AGlJ/KCrZuk6OirNHtdOdacvbcdUUbpkNpBSjdkrRm2If
VUnY1utIIJe6gFgnBUxXJ3RF5FZuhkdawc6V25HtDp6H3WamzJknKs5Vc4TlKp59
hZCOto7/+G/cd2XLdCKFUBl+new1pdDPsEm56+57DeZ7QGAQRX35PUQ5+HBjQJ/N
n/wJgS6wkEdIQLLwmCVxbHUkC+pRotTza5F2A0qZJgYPMcMpVFYKtzIa4GbWB5YS
MKGHbM8f3C8RLPQaHHTRycoA2Yor1I52B4Oi7605c5zHQr9pjrgtWsernDzkIhsB
ThYHSYQBUBTY4HBfzFwzCkVGqqLWNg==
=PMFY
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220907' of https://source.denx.de/u-boot/custodians/u-boot-stm
- simplify the STM32MP15x package parsing code
- remove test on CONFIG_DM_REGULATOR in stm32mp1 board
and enable CONFIG_DM_REGULATOR for stm32f769-disco
- handle ck_usbo_48m clock provided by USBPHYC to fix the command 'usb start'
after alignment with Linux kernel v5.19 DT (clocks = <&usbphyc>)
- Fix SYS_HZ_CLOCK value for stih410-b2260 board
- Switch STMM32MP15x DHSOM to FMC2 EBI driver
- Remove hwlocks from pinctrl in STM32MP15x to avoid issue with kernel
Several different firmware users have repetitive code to extract the
firmware data from a FIT. Add some helper functions to reduce the amount
of repetition. fit_conf_get_prop_node (eventually) calls
fdt_check_node_offset_, so we can avoid an explicit if. In general, this
version avoids printing on error because the callers are typically
library functions, and because the FIT code generally has (debug)
prints of its own. One difference in these helpers is that they use
fit_image_get_data_and_size instead of fit_image_get_data, as the former
handles external data correctly.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Correctly calculate offsets between SPL and proper U-Boot when new config
option CONFIG_FSL_PREPBL_ESDHC_BOOT_SECTOR for generating eSDHC boot sector
is enabled. Otherwise SPL would not be able to boot proper U-Boot.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
All *boot env commands overrides default boot source location via i2c.
After board reset without power off, BootROM then starts booting U-Boot
from this specified location instead of the default one.
Add new env command defboot which reverts boot location to the default
value, which in most cases is configurable by HW DIP switches.
And add new env commands norlowerboot, norupperboot, sd2boot to boot from
other locations. norlowerboot would instruct BootROM to boot from lower NOR
bank, norupperboot from upper NOR bank and sd2boot from SD card with
alternative configuration.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
SYS_HZ_CLOCK was wrongly set to 1GHz whereas it's set to 750MHz
by default by bootrom.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Grzegorz Szymaszek <gszymaszek@short.pl>
This commit sychronizes the header file for FU740 PRCI clocks with the
one from Linux 5.19.
The constant values are the same, but all constant names are changed
(most are just prefixed with FU740_).
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The frequency of the system counter is static which is given by the
COUNTER_FREQUENCY option. Remove COUNTER_FREQUENCY_REAL.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add an option to tell the TPM to commit non-volatile data immediately it
is changed, rather than waiting until later. This is needed in some
situations, since if the device reboots it may not write the data.
Add definitions for the rest of the Cr50 commands while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Add a vendor-specific TPM2 command for this and implement it for Cr50.
Note: This is not part of the TPM spec, but is a Cr50 extension.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
It is useful to read information about the current TPM state, where
supported, e.g. for debugging purposes when verified boot fails.
Add support for this to the TPM interface as well as Cr50. Add a simple
sandbox test.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This feature is used for measured boot, so we can add a log entry to the
TCPA with some information about where the digest comes from. It is not
currently supported in the TPM drivers, but add it to the API so that
code which expects it can signal its request.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Display the EBBRv2.0 conformance in the ECPT table.
The EBBRv2.0 conformance profile is set in the ECPT if
CONFIG_EFI_EBBR_2_0_CONFORMANCE=y.
Signed-off-by: Jose Marinho <jose.marinho@arm.com>
Add dependencies for CONFIG_EFI_EBBR_2_0_CONFORMANCE.
Enable the setting by default.
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The ECPT table will be included in the UEFI specification 2.9+.
The ECPT table was introduced in UEFI following the code-first path. The
acceptance ticket can be viewed at:
https://bugzilla.tianocore.org/show_bug.cgi?id=3591
The Conformance Profiles table is a UEFI configuration table that contains
GUID of the UEFI profiles that the UEFI implementation conforms with.
The ECPT table is created when CONFIG_EFI_ECPT=y.
The config is set by default.
Signed-off-by: Jose Marinho <jose.marinho@arm.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Some tests can have race conditions which are hard to detect on a single
one. Add a way to run tests more than once, to help with this.
Each individual test is run the requested number of times before moving
to the next test. If any runs failed, a message is shown.
This is most useful when running a single test, since running all tests
multiple times can take a while.
Signed-off-by: Simon Glass <sjg@chromium.org>
