When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
Since DRA7xx/AM57xx SR1.1 and SR1.0 has errata to limit the frequency of
MMC1 to 96MHz and frequency of MMC2 to 48MHz for AM572x SR1.1, limit the
frequency and disable higher speed modes for those revision.
Also use the recommended IO delays (those tagged with "rev11")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
board_usb_init()/_cleanup() should be in board files and don't have
a place in the xhci-omap driver. Weak versions for
board_usb_init()/_cleanup() already exist in common/usb.c
(for host mode) and drivers/usb/gadget/g_dnl.c (for gadget mode).
Therefore, remove init and cleanup functions from xhci-omap and
implement them in the board files.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
DRA762 comes in two packages:
- ABZ: Pin compatible package with DRA742 with DDR@1333MHz
- ACD: High performance(OPP_PLUS) package with new IPs
Both the above packages uses the same IDCODE hence needs to
differentiate using package information in DIE_ID_2.
Add support for the same. Also update clock, ddr, emif information.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
MCAN can be accessed via DCAN1 or DCAN2. Determining which DCAN instance
to use if any at all is done through
CTRL_CORE_CONTROL_SPARE_RW.SEL_ALT_MCAN. Since general pinmuxing is
handled in U-boot. Handle this additional pinmuxing requirement in U-boot
to ensure that MCAN is used by default via the DCAN1 pins.
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
[fcooper@ti.com: Update commit message and use DCAN1 not DCAN2 for MCAN]
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
All regulators are hooked to EN_Pin at reset so that EN Pin controls
their state. Hook the LDO1 regulator to EN pin which at reset is not
hooked. This applies only to LP8733.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
DRA71x processors are reduced pin and software compatible
derivative of DRA72 processors. Add support for detection
of SR2.1 version of DRA71x family of processors.
Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Add support for selecting proper dtb for
dra76x u-boot from FIT.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adding pinmux and IODELAY data for dra76-evm.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
dra76-evm has the ddr parts connectedi running at 666MHz:
EMIF1: MT41K512M16HA-125 AIT:A x 2
EMIF2: MT41K512M8RH-125-AAT:E x 4
Add support for configuring the above DDR parts.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
dra76-evm uses lp8736 and tps65917 pmic for powering on
various peripherals. Add data for these pmics and register
for dra76-evm.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The dra76-evm is a board based on TI's DRA76 processor
Add eeprom support
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
It is not necessary that ldo1 is used to power on mmc.
So, add support for passing ldo registers for powering on mmc.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
It is not necessary all omap5+ based uses the same PMIC
to poweron mmc. So add support for enabling mmc based on board.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
We are now using an env_ prefix for environment functions. Rename these
for consistency. Also add function comments in common.h.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.
Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
We are now using an env_ prefix for environment functions. Rename setenv()
for consistency. Also add function comments in common.h.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
This is a strange name for a function that loads the environment. There is
now only one implementation of this function, so use the new env_load()
function directly instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
One can obtain those variables using next commands:
$ fastboot getvar cpu
$ fastboot getvar secure
$ fastboot getvar board_rev
$ fastboot getvar userdata_size
Those variables are needed for fastboot.sh script.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now CONFIG_GENERIC_MMC and CONFIG_MMC match for all defconfig.
We do not need two options for the same feature. Deprecate the
former.
This commit was generated with the sed script 's/GENERIC_MMC/MMC/'
and manual fixup of drivers/mmc/Kconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
A weak version of the function board_usb_init is implemented in:
common/usb.c
drivers/usb/host/xhci-omap.c
To fix the double implementations:
* Convert the board_usb_init function in drivers/usb/host/xhci-omap.c
normal (not weak).
* The function board_usb_init in drivers/usb/host/xhci-omap.c calls to
the weak function omap_xhci_board_usb_init.
* Rename board version of the function board_usb_init to
omap_xhci_board_usb_init.
Done only for boards that defines CONFIG_USB_XHCI_OMAP.
To achieve the same flexibility with the function board_usb_cleanup:
* Add a normal (not weak) implementation of the function
board_usb_cleanup in drivers/usb/host/xhci-omap.c
* The function board_usb_cleanup in drivers/usb/host/xhci-omap.c calls
to the weak function omap_xhci_board_usb_cleanup.
* Rename board version of the function board_usb_cleanup to
omap_xhci_board_usb_cleanup.
Done only for boards that defines CONFIG_USB_XHCI_OMAP.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
As per the DM[1] Dated June 2016–Revised February 2017, Table 5-3,
DRA71 supports the following OPPs for various voltage domains:
VDD_MPU: OPP_NOM
VDD_CORE: OPP_NOM
VDD_GPU: OPP_NOM
VDD_DSPEVE: OPP_NOM, OPP_HIGH
VDD_IVA: OPP_NOM, OPP_HIGH
This patch add support for selection of the above OPPs instead of
using OPP_NOM for all voltage domains.
[1] http://www.ti.com/lit/ds/symlink/dra718.pdf
Reported-by: Vishal Mahaveer <vishalm@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
By making dram_init_banksize() return an error code we can drop the
wrapper. Adjust this and clean up all implementations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
To keep a consistent MMC device mapping in SPL and in u-boot, let's
register the MMC controllers the same way in u-boot and in the SPL.
In terms of boot time, it doesn't hurt to register more controllers than
needed because the MMC device is initialized only prior being accessed for
the first time.
Having the same device mapping in SPL and u-boot allows us to use the
environment in SPL whatever the MMC boot device.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add DT support for dra71-evm and built it as part of FIT image.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add the pmic_data for LP873x PMIC which is used to power
up dra71x-evm.
Note: As per the DM[1] DRA71x supports only OP_NOM. So, updating
the efuse registers only to use OPP_NOM irrespective of any
CONFIG_DRA7_<VOLT>_OPP_{NOM,od,high} is defined.
[1] http://www.ti.com/product/DRA718/technicaldocuments
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add mux and iodelay settings for dra71x-evm.
Data generated using PCT_DRA71x_SR2.0_v1.0.0.0 version (June 2016).
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The dra71x-evm is a board based on TI's DRA718 processor targeting BOM-optimized
entry infotainment systems such as display audio and is a software compatible
derivative of the highly successful DRA74 and DRA72 processor families.
More information can be found here[1].
Add epprom detection for dra71-evm.
[1] http://www.ti.com/product/dra718
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
It can be expected that different paper spins of a SoC can have
different definitions for OPP and can have their own constraints
on the boot up OPP for each voltage rail. In order to have this
flexibility, add support for dynamically selecting the OPP voltage
based on the board to handle any such exceptions.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Populate the corresponding TEE image processing call to be
performed during FIT loadable processing.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Verification has to be done before booting any images on HS devices. So
default the boot to FIT on HS devices.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
As a standard practice complex definitions should be protected
with parentheses, as it might fail when used in a complex if
statements.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add DTS support for dra72 evm Rev C which has the following
changes
* Two ethernet ports now instead of the single one in rev B.
* DP83867 ethernet phy instead of DP838865.
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Modify the SPL build procedure for AM57xx and DRA7xx high-security (HS)
device variants to create a secure u-boot_HS.img FIT blob that contains
U-Boot and DTB artifacts signed with a TI-specific process based on the
CONFIG_TI_SECURE_DEVICE config option and the externally-provided image
signing tool.
Also populate the corresponding FIT image post processing call to be
performed during SPL runtime.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently omap_vcores which holds pmic data is being assigned based
on the SoC type. PMIC is not a part of SoC. It is logical to
to assign omap_vcores based on board type. Hence over ride the
vcores_init function and assign omap_vcores based on the board type.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
FIT allows for a multiple dtb in a single image. SPL needs a way to
detect the right dtb to be used. Adding support for the same.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Adds the board specific ft_board_setup() functions that
are called when CONFIG_OF_BOARD_SETUP is defined. These functions
will currently just call the ft_cpu_setup() function.
Adds CONFIG_OF_BOARD_SETUP to the defconfig files
for dra72_evm, dra74_evm, and am57xx_evm.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable the TI DP83867 Giga bit phy on the
dra7 rev c board. The rx and tx internal
delays are need for this board so the usage
of RGMII_ID is required.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add the pinmux data for rev C evm. This is different from previous
revisions of the platform thanks to the deltas introduced both from
silicon side and from SoC side.
Based on J6EcoES2_EVM_Base_Config-20160309b and PCT-DRA72x-v1.3.0.7 for
SR2.0 silicon.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
DDR configuration has changes from SR1.1 based Rev-A/B version of evm
to the SR2.0 based Rev C of the EVM. Rev C evm now uses the higher
density MT41K512M8RH-125-AAT:E (IT) which is of size 2GB.
Update the DDR configuration based on data from EMIF configuration
tool 1.1.1. NOTE: we use eeprom information (ram_size) to update the
configuration.
Tested-by: Vishal Mahaveer <vishalm@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
There is no distinction between essential and non-essential mux configuration,
so it doesn't make sense to have an "essential" prefix.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
All the mux configurations needs to be done as part of the IODelay
sequence to avoid glitch. Adding all the mux configuration, MANUAL/VIRTUAL
mode configuration as needed for DRA72-evm.
Also update the mux for SD card detect on DRA74-evm.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Updating the memory banks properly so that DT is populated accordingly.
And updating this only after DDR is properly detected by eeprom, so that
git bisect is still maintained.
Acked-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The REVH and later versions of DRA7-evm uses MICRON MT41K512M16HA-125 memory
chips which is of size 4GB(2GB on EMIF1 and 2GB on EMIF2). Add support for the
same.
Acked-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The newer versions of DRA7 boards has EEPROM populated with DDR
size specified in it. Moving DRA7 specific emif related settings
to board files so that emif settings can be identified based on EEPROM.
Acked-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Now that we have a common prototype to grab the omap die id, functions to figure
out a serial number and usb ethernet address can use it directly.
Those also get an omap_die_id prefix for better consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
