Commit graph

18 commits

Author SHA1 Message Date
Manish Narani
15ca9ebb07 arm64: zynqmp: Move USB3 PHY properties from DWC3 node to USB node
Move the PHY properties from DWC3 node to USB node in ZynqMP DTs as here
the USB3 PHY used is PSGTR, which is connected to Xilinx USB core. This
PHY initialization should be handled from Xilinx USB core as the
prerequisite register configurations are done here only.

Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-07-26 09:26:41 +02:00
Michal Simek
52caf2c12b arm64: zynqmp: Remove gpio from aliases list
It is not recommended to have aliases for gpio. In past it was used in
Linux for assigning numbers via sysfs which is deprecated and libgpiod
should be used instead.
In U-Boot this number is used for seq number but gpio offset are not
counted from this number. That's why having these aliases only for seq
number is not needed. As is done in Linux it is the best to use full gpio
name instead of sequence number which depends on sequence in binding.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:36 +02:00
Michal Simek
531abcb71e xilinx: Convert xlnx,eeprom property to nvmem alias
Convert all boards to use nvmem alias instead of xlnx,eeprom. The change is
done based on discussion in the link below.

Link: https://lore.kernel.org/r/CAL_JsqLMDqpkyg-Q7mUfw-XH67-v068Q6e9wTq2UOoN=0-_coQ@mail.gmail.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
184309b8c6 arm64: zynqmp: Add maximum-speed property for dwc3 nodes
dwc3 can be used only for higher speeds than super-speed that's why
explicitly set it up.
This is also aligned with other ZynqMP dts files.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
447fb8db02 arm64: zynqmp: Update Copyright years to 2021
Trivial change for all files I have touched recently.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
1242a6b13d arm64: zynqmp: Update psgtr clocks index for boards
Update the psgtr clock indexing for couple of zynqmp boards.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
3195840c94 arm64: zynqmp: Add psgtr DT descriptions
Mainline kernel has psgtr driver that's why it is good to add description
to DT files. Some boards are just missing description for USB3 and sata.
zc1751-dc1 and p-a2197 are also missing clock descriptions for input
clocks.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-05-19 09:44:50 +02:00
Michal Simek
bd00849ae9 arm64: zynqmp: Add pinctrl description
ZynqMP pinctrl Linux driver has been merged to 5.13-rc1 kernel. Based on it
DT files can be extended by pinctrl configurations.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-05-19 09:44:50 +02:00
Michal Simek
fddff6815a arm64: zynqmp: Remove comment about clock chips
These comments weren't push to mainline that's why remove them.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-05-19 09:44:50 +02:00
Raviteja Narayanam
486f25c727 arm64: zynqmp: Add 'i2c-mux-idle-disconnect' property
I2C muxes that have the slave devices with same address are
falling into the below problem.

VCK190 system controller (SC) - zynqmp-e-a2197-00-revA.dts
I2C1 (0xff030000) -> Mux1 (@0x74) -> Channel 3 -> 0x50
I2C1 (0xff030000) -> Mux2 (@0x75) -> Channel 0 -> 0x50

1. SC accesses I2C1 - Mux1 (0x74) - Channel 3 and then
2. SC accesses I2C1 - Mux2 (0x75) - Channel 0.

Now it results in 2 slave devices with same address (0x50)
on the I2C bus, making the communication un-reliable.

When ' i2c-mux-idle-disconnect' is in DT, after '1', the Mux
channel output is disconnected, making none of the channels
available to the I2C1. So, there is no question of having the
same addressed slave (0x50) present on the bus when we are doing '2'.

Same pattern is seen in below two boards also.

ZCU208 - zynqmp-zcu208-revA.dts
ZCU216 - zynqmp-zcu216-revA.dts

Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
2021-05-19 09:44:50 +02:00
Michal Simek
ce90654d1c xilinx: Sync DTs with Linux kernel
There are several changes which happen in mainline kernel which should get
also to U-Boot. Here is the list of patches from the kernel:

- ARM: zynq: Fix leds subnode name for zc702/zybo-z7
- arm64: dts: zynqmp: Fix leds subnode name for zcu100/ultra96 v1
- arm64: dts: zynqmp: Fix u48 si5382 chip on zcu111
- arm64: dts: zynqmp: Wire up the DisplayPort subsystem
- arm64: dts: zynqmp: Add DisplayPort subsystem
- arm64: dts: zynqmp: Add DPDMA node
- arm64: dts: zynqmp: Enable phy driver for Sata on zcu102/zcu104/zcu106
- arm64: dts: zynqmp: Enable si5341 driver for zcu102/106/111
- arm64: dts: zynqmp: Add DT description for si5328 for zcu102/zcu106
- arm64: dts: zynqmp-zcu100-revC: correct interrupt flags
- arm64: dts: xilinx: align GPIO hog names with dtschema
- arm64: zynqmp: Add Xilinx AES node
- dt: bindings: dma: xilinx: dpdma: DT bindings for Xilinx DPDMA

but also some other changes have been done.
- Using only one compatible string for adxl345 on zturn
- Remove Xilinx internal DP bindings
- Remove USB3.0 serdes configurations
- Remove SATA serdes configuration for zc1232
- Resort nvmem_firmware
- Update nand compatible string
- Aling power-domains property for sd0/1

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-03-30 12:03:24 +02:00
Michal Simek
9577b2edf3 arm64: zynqmp: Add idt 8a34001 chip to zcu208/zcu216
There is Linux driver for these chips that's why add it to device tree.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-03-30 12:03:24 +02:00
Michal Simek
01a6da1661 xilinx: Fix xlnx,mio_bank property
s/xlnx,mio_bank/xlnx,mio-bank/g

DT binding is describing mio-bank not mio_bank that's why fix all DTSes and
also driver itself.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
2020-08-20 09:49:20 +02:00
Michal Simek
14c0fbbc94 arm64: zynqmp: Fix irps5401 device nodes
- Do not use irps54012 as device node which is not correct.
- Fix addresses of irps5401/u180 on zcu104 revisions.
- Remove clock-cells property. It is PMIC without any clock output.
- Define irps5401 nodes in zynqmp-e-a2197

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-04-27 14:21:18 +02:00
Manish Narani
12ffe75819 arm64: zynqmp: Add 'no-1-8-v' property for ZynqMP Boards
Modify dts files to add 'no-1-8-v' property for all the ZynqMP boards.
User can remove this property to enable the UHS mode. This is to keep
the same speed (HS) modes across all the stages of the Linux Boot. Due
to power cycling limitation of some of the ZynqMP boards, some SD cards
don't get power cycled and are failing in Linux.

Signed-off-by: Manish Narani <manish.narani@xilinx.com>
2020-04-06 12:51:31 +02:00
Michal Simek
d31f1c9236 arm64: zynqmp: Update Copyright years to 2020
Trivial change.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-04-06 12:51:31 +02:00
Michal Simek
f695e1c889 arm64: zynqmp: Replace gpio-key,wakeup with wakeup source
The same change has been done for Zynq by commit 1241c72b6db1
("ARM: dts: zynq: replace gpio-key,wakeup with wakeup-source property")
in mainline Linux kernel.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-04-06 12:51:31 +02:00
Michal Simek
a81186fd9f arm64: zynqmp: Add support for zcu208
The board is very similar to zcu216 with zu49dr device.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14 09:05:55 +01:00