This patch adds support for the kmeter1 board from Keymile,
based on a Freescale MPC8360 CPU.
- serial console on UART 1
- 256 MB DDR2 RAM
- 64 MB NOR Flash
- Ethernet RMII Mode over UCC4
- PHY SMSC LAN8700
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch provides support for AFEB9260 board, a product of
OpenSource hardware and software. Some commertial projects
are made with this design. A board is basically AT91SAM9260-EK
with some modifications and different peripherals and different
parts used. Main purpose of this project is to gain experience in
hardware design.
More info: http://groups.google.com/group/arm9fpga-evolution-board
(In Russian only, sorry).
Subversion repository: svn://194.85.238.22/home/users/george/svn/arm9eb
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
This patch adds support for the avnet fx12 minimodul.
It needs the "ppc4xx: Generic architecture for xilinx ppc405"
patch from Ricardo.
Signed-off-by: Georg Schardt <schardt@team-ctech.de>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
The Arches Evaluation board is based on the AMCC 460GT SoC chip.
This board is a dual processor board with each processor providing
independent resources for Rapid IO, Gigabit Ethernet, and serial
communications. Each 460GT has it's own 512MB DDR2 memory, 32MB NOR
FLASH, UART, EEPROM and temperature sensor, along with a shared debug
port. The two 460GT's will communicate with each other via shared
memory, Gigabit Ethernet and x1 PCI-Express.
Signed-off-by: Adam Graham <agraham@amcc.com>
Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch provides an unificated way of handling xilinx v5 ppc440 boards.
It unificates 3 different things:
1) Source code
A new board called ppc440-generic has been created. This board includes
a generic tlb initialization (Maps the whole memory into virtual) and
defines board_pre_init, checkboard, initdram and get_sys_info weakly,
so, they can be replaced by specific functions.
If a new board needs to redefine any of the previous functions
(specific initialization) it can create a new directory with the
specific initializations needed. (see the example ml507 board).
2) Configuration file
Common configurations are located under configs/xilinx-ppc440.h, this
header file interpretes the xparameters file generated by EDK and
configurates u-boot in correspondence. Example: if there is a Temac,
allows CMD_CONFIG_NET
Specific configuration are located under specific configuration file.
(see the example ml507 board)
3) Makefile
Some work has been done in order to not duplicate work in the Main
Makefile. Please see the attached code.
In order to support new boards they can be implemented in the next way:
a) Simple Generic Board (90% of the time)
Using EDK generates a new xparameters.h file, replace
ppc440-generic/xparameters.h and run make xilinx-ppc440-generic_config
&& make
b) Simple Boards with special u-boot parameters (9 % of the time)
Create a new file under configs for it (use ml507.h as example) and
change your paramaters. Create a new Makefile paragraph and compile
c) Complex boards (1% of the time)
Create a new folder for the board, like the ml507
Finally, it adds support for the Avnet FX30T Evaluation board, following
the new generic structure:
Cheap board by Avnet for evaluating the Virtex5 FX technology.
This patch adds support for:
- UartLite
- 16MB Flash
- 64MB RAM
Prior using U-boot in this board, read carefully the ERRATA by Avnet
to solve some memory initialization issues.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
AP325RXA is SH7723's reference board.
This has SCIF, NOR Flash, Ethernet, USB host, LCDC, SD Host, Camera and other.
In this patch, support SCIF, NOR Flash, and Ethernet.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This adds initial support for the RTE RSK+ SH7203 board.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This board has SH7785, 512MB DDR2-SDRAM, NOR Flash,
Graphic, Ethernet, USB, SD, RTC, and I2C controller.
This patch supports the following functions:
- 128MB DDR2-SDRAM (29-bit address mode only)
- NOR Flash
- USB host
- Ethernet
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
SMDK6400 can only boot U-Boot from NAND-flash. This patch adds a nand_spl
driver for it too. The board can also boot from the NOR flash, but due to
hardware limitations it can only address 64KiB on it, which is not enough
for U-Boot. Based on the original sources by Samsung for U-Boot 1.1.6.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Dejan Minic <minic@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MIMC200 board is based on Atmel's NGW100 dev kit, but with an extra
8MByte FLASH and 128KByte FRAM.
Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch adds support for the Favr-32 board made by EarthLCD.
This kit, which is also called ezLCD-101 when running with EarthLCD firmware,
has a 10.4" touch screen LCD panel, 16 MB 32-bit SDRAM, 8 MB parallel flash,
Ethernet, audio out, USB device, SD-card slot, USART and various other
connectors for cennecting stuff to SPI, I2C, GPIO, etc.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch allows booting from FLASH the ML507 board by Xilinx.
Previously, U-Boot needed to be loaded from JTAG or a Sytem ACE CF
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
The Hammerhead platform is built around a AVR32 32-bit microcontroller
from Atmel. It offers versatile peripherals, such as ethernet, usb
device, usb host etc.
The board also incooperates a power supply and is a Power over Ethernet
(PoE) Powered Device (PD).
Additonally, a Cyclone III FPGA from Altera is integrated on the board.
The FPGA is mapped into the 32-bit AVR memory bus. The FPGA offers two
DDR2 SDRAM interfaces, which will cover even the most exceptional need
of memory bandwidth. Together with the onboard video decoder the board
is ready for video processing.
For more information see: http:///www.miromico.com/hammerhead
Signed-off-by: Julien May <mailinglist@miromico.ch>
[haavard.skinnemoen@atmel.com: various small fixes and adaptions]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Support for the adsvix was originally provided by Applied Data
Systems (ADS), inc., now EuroTech, Inc.
The board never shipped aside from some sample boards.
Signed-off-by: Adrian Filipi <adrian.filipi@eurotech.com>
The Xilinx ML507 Board is a Virtex 5 prototyping board that includes,
among others:
-Virtex 5 FX FPGA (With a ppc440x5 in it)
-256MB of SDRAM2
-32MB of Flash
-I2C Eeprom
-System ACE chip
-Serial ATA connectors
-RS232 Level Conversors
-Ethernet Transceiver
This patch gives support to a standard design produced by EDK for this
board: ppc440, uartlite, xilinx_int and flash
- Includes Changes propossed by Stefan Roese and Michal Simek
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Acked-by: Stefan Roese <sr@denx.de>
The MVBC_P is a MPC5200B based camera system with Intel Gigabit ethernet
controller (using e1000) and custom Altera Cyclone-II FPGA on PCI.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add AMCC Redwood reference board that uses the latest
PPC 464 CPU processor combined with a rich mix of peripheral
controllers. The board will support PCIe, mutiple Gig ethernet
ports, advanced hardware RAID assistance and IEEE 1588.
Signed-off-by: Feng Kan <fkan@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
By Cleanup out-or-tree building for some boards (.depend)
(commit:c8a3b109f07f02342d097b30908965f7261d9f15)
because filse ware changed, some SH-boards have compile error.
I revised this problem.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch adds support for the Lyrtech SFF-SDR board,
based on the TI DaVinci architecture (ARM926EJS).
Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Signed-off-by: Philip Balister <philip@balister.org>
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch adds basic support for the TQM8548 module from TQ-Components
(http://www.tqc.de/) including DDR2 SDRAM initialisation and support for
eTSEC 3 and 4
Furthermore Flash buffer write has been enabled to speed up output to
the Flash by approx. a factor of 10.
Signed-off-by: Thomas Waehner <thomas.waehner@tqs.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Add MPC8343 based board mvBlueLYNX-M7.
It's a single board stereo camera system.
Please read doc/README.mvblm7 for details.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
SH7763RDP has SCIF, NOR Flash, Ethernet, USB host, LCDC and MMC.
In this patch, support SCIF, NOR Flash, and Ethernet.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This is a replacement for ATSTK1002 with 64MB SDRAM and NAND flash on
board. It's currently in production and will be available soon.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch adds support for the AT91SAM9RL chip and the AT91SAM9RLEK
board.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch adds support for the AT91SAM9263 chip and the AT91SAM9263EK
board.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch adds support for the AT91SAM9261 chip and the AT91SAM9261EK
board.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch adds support for the MX31ADS evaluation board from Freescale,
initialization code is copied from RedBoot sources, also provided by
Freescale.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
This patch is based on the port by Mihai Georgian (see linkstation.c for
Copyright information) and implements support for LinkStation / KuroBox HD
and HG PPC models from Buffalo Technology, whereby HD is deactivated at
the moment, pending network driver fixing.
Notice to users: this is pretty much a barebone port. Support for network
on HG models is already in the U-Boot mainline, but you might also want
patches to switch fan / phy modes depending on the negotiated ethernet
parameters. This patch also doesn't support console switching, booting EM
mode, Buffalo specific ext2 magic number. So, if you want to use any of
those, you need additional patches. Otherwise this patche provides a fully
functional u-boot with a network console on your system.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
This patch adds support for the Phytec Phycore-i.MX31 board
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
This patch adds support for the mx31 litekit board
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
This board never went into production
Signed-off-by: Zachary P. Landau <zachary.landau@labxtechnologies.com>
Acked-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Acked-by: John Rigby <jrigby@freescale.com>
Add some missing ARM boards to MAKEALL. These build correctly,
unlike several of the boards already listed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This patch adds support for the MX31ADS evaluation board from Freescale,
initialization code is copied from RedBoot sources, also provided by Freescale.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
This patch adds support for the Phytec Phycore-i.MX31 board
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
This patch adds support for the mx31 litekit board
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
R2D plus is SH reference board used with SH7751R.
This board has 266Mhz CPU, 64MB SDRAM, Cardbus, CF interface,
one PCI bus, VGA, and two Ethernet controller.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Renesas Solutions R7780MP is a reference board on SH7780.
This board has serial, 10/100 base Ethernet deivice, CF slot
and VGA devices. This board can set extension board.
Extension board has 10/100/1000 base Ethernet device, PCI slot,
S-ATA, iDVR slot.
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Migo-R is a board based on SH7722 and has may devices.
In this patch, supported SCIF, NOR flash and Ethernet.
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch adds support for the AMCC Glacier 460GT eval board.
The main difference to the Canyonlands board are listed here:
- 4 ethernet ports instead of 2
- no SATA port
- no USB port
Currently EMAC2+3 are not working. This will be fixed in a later
release.
Signed-off-by: Stefan Roese <sr@denx.de>
460EX doesn't support a fixed bootstrap option to boot from 512 byte page
NAND devices. The only bootstrap option for NAND booting is option F for
2k page devices. So to boot from a 512 bype page device, the I2C bootstrap
EEPROM needs to be programmed accordingly.
This patch adds basic NAND booting support for the AMCC Canyonlands aval
board and also adds support to the "bootstrap" command, to enable NAND
booting I2C setting.
Tested with 512 byte page NAND device (32MByte) on Canyonlands.
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for the ATNGW100 Network Gateway reference design,
including flash, ethernet and MMC support.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Hi,
The patch adds 4 boards, called AcTux-1 .. AcTux-4. This patch contains the
files that
contain changes for multiple boards, the board-specific files follow as
separate patches.
Signed-off-by: Michael Schwingen <michael@schwingen.org>
With serial, NE2000, IDE support. Tested in big-endian mode.
Memory size hard-coded to 128M for now, so don't play with
the -m option.
Signed-off-by: Vlad Lungu <vlad@comsys.ro>
MPC837xERDB board support includes:
* DDR2 330MHz hardcoded (soldered on the board)
* Local Bus NOR Flash
* I2C, UART and RTC
* eTSEC RGMII (TSEC0 - RTL8211B with MII;
* TSEC1 - VSC7385 local bus, hardcoded, requires seperate firmware
* load)
Signed-off-by: Kevin Lam <kevin.lam@freescale.com>
Signed-off-by: Joe D'Abbraccio <joe.d'abbraccio@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The features list:
- Boot from NOR Flash
- DDR2 266MHz hardcoded configuration
- Local bus NOR Flash R/W operation
- I2C, UART, MII and RTC
- eTSEC0/1 support
- PCI host
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The TK885D board uses a TQM885D module from TQ, this port adds an
own configuration file and adds a last_stage_init() method to
configure the two PHYs, depending on the phy_auto_nego environment
variable.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
This is MPC8360E based board with:
- 256MB fixed SDRAM;
- 8MB Intel Strata NOR flash;
- StMICRO 64MiB NAND flash;
- two 10/100/1000 ethernet ports connected via Broadcom
BCM5481 PHYs;
- two 10/100 ethernet ports connected via National
DP83848 PHYs;
- one PCI and one miniPCI slots;
- four serial ports (two NS16550-compatible, two UCCs);
- four USB ports working through MPC8360E "FHCI" USB controller;
- Fujitsu MB86277 graphics controller;
- Analog to Digital Converter/Touchscreen controller, AD7843
connected to SPI.
Features not supported in this patch are:
- StMICRO 64MiB NAND flash (patch sent);
- MINT framebuffer initialization (patch is pending);
- Fetching production information from the EEPROM via I2C;
- FHCI USB;
- Two slow UCCs used as RS-485 UARTs.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Add support for Wind River's SBC8548 reference board.
Signed-off by: Joe Hamman <joe.hamman@embeddedspecialties.com>
Signed-off by: Andy Fleming <afleming@freescale.com>
This patch brings the PMC440 board configuration file.
Finally it enables the PMC440 board support.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
This board never left prototyping state and it
became a millstone round my neck. So remove it.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
These patches add support for the PPC440EPx-based "Korat" board to
U-Boot. They are based primarily on support for the Sequoia board.
Signed-off-by: Larry Johnson <lrj@acm.org>
ATSTK1004 is a daughterboard for ATSTK1000 with the AT32AP7002 CPU,
which is a derivative of AT32AP7000.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
ATSTK1003 is a daughterboard for ATSTK1000 with the AT32AP7001 CPU,
which is a derivative of AT32AP7000.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This patch adds NAND booting support for the AMCC 405EX(r) eval boards.
Again, only one image supports both targets.
Signed-off-by: Stefan Roese <sr@denx.de>
The Haleakala is nearly identical with the Kilauea eval board. The only
difference is that the 405EXr only supports one EMAC and one PCIe
interface. This patch adds support for the Haleakala board by using
the identical image for Kilauea and Haleakala. The distinction is done
by comparing the PVR.
Signed-off-by: Stefan Roese <sr@denx.de>
Add MPC8360EMDS_ATM_config and MPC832XEMDS_ATM_config into
Makfile and MAKEALL
Signed-off-by: Tony Li <tony.li@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Mahesh Jade <mahesh.jade@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Changes to the TSEC driver affect almost all 83xx, 85xx, and 86xx boards.
Now we can do a MAKEALL test on all of them!
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add support for Wind River's SBC8641D reference board.
Signed-off by: Joe Hamman <joe.hamman@embeddedspecialties.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Acked-by: Jon Loeliger <jdl@freescale.com>
Add support for the following DaVinci boards:
- DV_EVM
- SCHMOOGIE
- SONATA
Changes:
- Split into separate board directories
- Removed changes to MTD_DEBUG (or whatever it's called)
- New CONFIG_CMD party line followed
- Some cosmetic fixes, cleanup etc.
- Patches against the latest U-Boot tree as of now.
- Fixed CONFIG_CMD_NET in net files.
- Fixed CONFIG_CMD_EEPROM for schmoogie.
- Made sure it compiles and works (forceenv() link problem) on SCHMOOGIE and
DV_EVM. Can't check if it works on SONATA, don't have a board any more,
but it at least compiles.
Here is an excerpt from session log on SCHMOOGIE...
U-Boot 1.2.0-g6c33c785-dirty (Aug 7 2007 - 13:07:17)
DRAM: 128 MB
NAND: 128 MiB
In: serial
Out: serial
Err: serial
ARM Clock : 297MHz
DDR Clock : 162MHz
ETH PHY : DP83848 @ 0x01
U-Boot > iprobe
Valid chip addresses: 1B 38 3A 3D 3F 50 5D 6F
U-Boot > ping 192.168.253.10
host 192.168.253.10 is alive
U-Boot >
Signed-off-by: Sergey Kubushyn <ksi@koi8.net>
Acked-by: Dirk Behme <dirk.behme@gmail.com>
Acked-by: Zach Sadecki <Zach.Sadecki@ripcode.com>
Acked-by: Stefan Roese <sr@denx.de>
This series of patches adds support for 2 boards from Netstal Maschinen.
The HCU4 has a PPC405Gpr and
the HCU5 has a PPC440EPX.
The HCU4 has a somehow complicated flash setup, as the booteprom is
only 8 bits and the CFI 16 bits wide, which makes it impossible to use a more
elegant solution.
The HCU5 has only a booteprom as the whole code will be downloaded from a
different board which has HD, CD-ROM, etc and where all code is stored.
This is my third try. I incorporated all suggestions made by Wolfgang and Stefan.
Thanks them a lot.
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
Add the ability for modules from the Schindler cm5200 family to use a
single U-Boot image:
- rename cm1_qp1 to cm5200
- add run-time module detection
- parametrize SDRAM configuration according to the module we are running on
Few minor, board-specific fixes included in this patch:
- better MAC address handling
- updated default environment ('update' command uses +{filesize} now)
- improved error messages in the auto-update code
- allow booting U-Boot from RAM (CFG_RAMBOOT)
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Signed-off-by: Piotr Kruszynski <ppk@semihalf.com>
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
This patch adds NAND booting support for the AMCC Acadia eval board.
Please make sure to configure jumper J7 to position 2-3 when booting
from NOR, and to position 1-2 when booting for NAND.
I also added a board command to configure the I2C bootstrap EEPROM
values. Right now only 267MHz is support for booting either via NOR
or NAND FLASH. Here the usage:
=> bootstrap 267 nor ;to configure the board for 267MHz NOR booting
=> bootstrap 267 nand ;to configure the board for 267MHz NNAND booting
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds NAND booting support for the AMCC Bamboo eval board.
Since the NAND-SPL boot image is limited to 4kbytes, this version
only supports the onboard 64MBytes of DDR. The DIMM modules can't be
supported, since the setup code for I2C DIMM autodetection and
configuration is too big for this NAND bootloader.
Signed-off-by: Stefan Roese <sr@denx.de>
* Add support to the Makefile
* Add 8544 configuration support to the tsec driver
* Add 8544 SVR numbers to processor.h
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
This patch adds support for the new AMCC Acadia eval board.
Please note that this Acadia/405EZ support is still in a beta stage.
Still lot's of cleanup needed but we need a preliminary release now.
Signed-off-by: Stefan Roese <sr@denx.de>
timer support
interrupt controller support
flash support
ethernet support
cache support
board information support
env support
booting image support
adding support for Xilinx ML401
Add support for the MPC8349E-mITX-GP, a stripped-down version of the
MPC8349E-mITX. Bonus features include support for low-boot (BMS bit in
HRCW is 0) for the ITX and a README for the ITX and the ITX-GP.
Signed-off-by: Timur Tabi <timur@freescale.com>
Conflicts:
drivers/cfi_flash.c
The patch by Heiko Schocher <hs@pollux.denx.de> on Jan, 19, 2007
fixes cfi_driver bug for mpc7448hpc2 board. The default cfi_driver can support
mpc7448hpc2 board.
The conflicts due to a new mpc7448 p3m7448 board is in the main tree.
Merge branch 'master' into hpc2
Conflicts:
MAKEALL
cpu/74xx_7xx/cpu.c
cpu/74xx_7xx/cpu_init.c
cpu/74xx_7xx/speed.c
This patch adds support for the Prodrive P3M750 (PPC750 & MV64460)
and the P3M7448 (MPC7448 & MV64460) PMC modules. Both modules are
quite similar and share the same board directory "prodrive/p3mx"
and the same config file "p3mx.h".
Signed-off-by: Stefan Roese <sr@denx.de>
PREREQUISITE PATCHES:
* This patch can only be applied after the following patches have been applied:
1) DNX#2006090742000024 "Add support for multiple I2C buses"
2) DNX#2006090742000033 "Multi-bus I2C implementation of MPC834x"
3) DNX#2006091242000041 "Additional MPC8349 support for multibus i2c"
4) DNX#2006091242000078 "Add support for variable flash memory sizes on 83xx systems"
5) DNX#2006091242000069 "Add support for Errata DDR6 on MPC 834x systems"
CHANGELOG:
* Add support for the Freescale MPC8349E-mITX reference design platform.
The second TSEC (Vitesse 7385 switch) is not supported at this time.
Signed-off-by: Timur Tabi <timur@freescale.com>
1. Add 7447A and 7448 processor support.
2. Add the following flags.
CFG_CONFIG_BUS_CLK : If the 74xx bus frequency can be configured dynamically
(such as by switch on board), this flag should be set.
CFG_EXCEPTION_AFTER_RELOCATE: If an exception occurs after the u-boot
relocates to RAM, this flag should be set.
CFG_SERIAL_HANG_IN_EXCEPTION: If the print out function will cause the
system hang in exception, this flag should be set.
There is a design issue for tsi108/109 pci configure read. When pci scan
the slots, if there is no pci card, the tsi108/9 will cause a machine
check exception for mpc7448 processor.
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Patch by Haavard Skinnemoen, 06 Sep 2006
This patch adds support for the ATSTK1000 with the ATSTK1002 CPU
daughterboard.
ATSTK1000 is a full-featured development board for AT32AP CPUs. It
has two ethernet ports, a high quality QVGA LCD panel, a loudspeaker,
and connectors for USART, PS/2, VGA, USB, MMC/SD cards and
CompactFlash cards. For more information, please see this page:
http://www.atmel.com/dyn/products/tools.asp?family_id=682
The ATSTK1002 is a daughterboard for the ATSTK1000 supporting the
AT32AP7000 chip.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
- Add support for PPC440EPx & PPC440GRx
- Add support for PPC440EP(x)/GR(x) NAND controller
in cpu/ppc4xx directory
- Add NAND boot functionality for Sequoia board,
please see doc/README.nand-boot-ppc440 for details
- This Sequoia NAND image doesn't support environment
in NAND for now. This will be added in a short while.
Patch by Stefan Roese, 07 Sep 2006
Modifications are based on the linux kernel approach and
support two use cases:
1) Add O= to the make command line
'make O=/tmp/build all'
2) Set environement variable BUILD_DIR to point to the desired location
'export BUILD_DIR=/tmp/build'
'make'
The second approach can also be used with a MAKEALL script
'export BUILD_DIR=/tmp/build'
'./MAKEALL'
Command line 'O=' setting overrides BUILD_DIR environent variable.
When none of the above methods is used the local build is performed and
the object files are placed in the source directory.
- make highboot configurations use environment at high end, too,
to avoid flash fragmentation
- always use redundand environment
- don't enable video code for modules without graphics controller
- provide useful (though different) mtdparts settings
- get rid of CONFIG_CS_AUTOCONF which was always set anyway
* Extend mkconfig tool to print more useful target name
- Support for TQM5200S (short version without graphic controller)
- Support for modules with 'N' type S29GL128N Spansion flashes
(requires changes to flash layout)
- Support for MPC5200B cpu (mostly support for second SDRAM bank)
Make the automatic CS configuration the default.
The dedicated configurations CONFIG_TQM5200_AA, CONFIG_TQM5200_AB
and CONFIG_TQM5200_AC are removed.
"TQM5200_config" is now the default for STK52XX.200 base boards.
On a STK52XX.100 base board "TQM5200_STK100_config" must be used.
Patch by Martin Krause, 07 Nov 2005
- Add IXP4xx NPE ethernet MAC support
- Add support for Intel IXDPG425 board
- Add support for Prodrive PDNB3 board
- Add IRQ support
Patch by Stefan Roese, 23 May 2006
[This patch does not include cpu/ixp/npe/IxNpeMicrocode.c which still
sufferes from licensing issues. Blame Intel.]
- Removed MPC8349ADS port
- Added PCI support to MPC8349ADS
- reworked memory map to allow mapping of all regions with BATs
Patch by Kumar Gala 20 Apr 2006
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
relocate ichache_State to ram
u-boot can run from internal flash
Add EB+MCF-EV123 board support.
Add m68k Boards to MAKEALL
Patch from Jens Scharsig, 08 Aug 2005
code and in SoC code). Boards using the old way have CFG_NAND_LEGACY and
BOARDLIBS = drivers/nand_legacy/libnand_legacy.a added. Build breakage for
NETTA.ERR and NETTA_ISDN - will go away when the new NAND support is
implemented for these boards.
done so far:
* created zylonite board dir (based on lubbock)
* extended some - but not all pxa sources and headers for Intel
Monahans support (CONFIG_CPU_MONAHANS)
* created Makefile zylonite target + MAKEALL entry
* added some debug nonsense, remove later, grep for mk@tbd
Status: compiles (eldk-4.0), and can be started with BDI, but runs forever
and doesn't halt at breakpoints. Hmmm...
- Support for TQM8541/8555 boards added.
- Complete rework of TQM8540/8560 support.
- Common TQM85xx code now supports all current TQM85xx platforms
(TQM8540/8541/8555/8560).
- DDR SDRAM size detection added.
- CAS latency default values can be overwritten by setting "serial#"
to e.g. "ABC0001 casl=25" -> CAS latency 2.5 will be used.
If problems are detected with this non default CAS latency,
the defualt values will be used instead.
- FLASH size detection added.
- Moved FCC ethernet driver initialization behind TSEC driver init
-> TSEC is first device.
Patch by Stefan Roese, 30 Nov 2005
- Added onboard PPC440 DDR autodetection in cpu/ppc/sdram.c
- CFG_FLASH_QUIET_TEST added to use the common CFI driver
for bank autodetection
Patch by Stefan Roese, 22 Nov 2005
