Commit graph

38 commits

Author SHA1 Message Date
Pratyush Yadav
38b0852b0e spi: cadence-qspi: Add support for octal DTR flashes
Set up opcode extension and enable/disable DTR mode based on whether the
command is DTR or not.

xSPI flashes can have a 4-byte dummy address associated with some
commands like the Read Status Register command in octal DTR mode. Since
the flash does not support sending the dummy address, we can not use
automatic write completion polling in DTR mode. Further, no write
completion polling makes it impossible to use DAC mode for DTR writes.
In that mode, the controller does not know beforehand how long a write
will be and so it can de-assert Chip Select (CS#) at any time. Once CS#
is de-assert, the flash will go into burning phase. But since the
controller does not do write completion polling, it does not know when
the flash is busy and might send in writes while the flash is not ready.

So, disable write completion polling and make writes go through indirect
mode for DTR writes and let spi-mem take care of polling the SR.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-28 11:57:23 +05:30
Pratyush Yadav
a6903aa7ea spi: cadence-qspi: Add a small delay before indirect writes
Once the start bit is toggled it takes a small amount of time before it
is internally synchronized. This means we can't start writing during
that part. So add a small delay to allow the bit to be synchronized.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-28 11:57:10 +05:30
Pratyush Yadav
bd8c8dcd4d spi: cadence-qspi: Do not calibrate when device tree sets read delay
If the device tree provides a read delay value, use that directly and do
not perform the calibration procedure.

This allows the device tree to over-ride the read delay value in cases
where the read delay value obtained via calibration is incorrect. One
such example is the Cypress Semper flash. It needs a read delay of 4 in
octal DTR mode. But since the calibration procedure is run before the
flash is switched in octal DTR mode, it yields a read delay of 2. A
value of 4 works for both octal DTR and legacy modes.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-28 11:56:53 +05:30
Simon Glass
0fd3d91152 dm: Use access methods for dev/uclass private data
Most drivers use these access methods but a few do not. Update them.

In some cases the access is not permitted, so mark those with a FIXME tag
for the maintainer to check.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
2021-01-05 12:24:40 -07:00
Simon Glass
8a8d24bdf1 dm: treewide: Rename ..._platdata variables to just ..._plat
Try to maintain some consistency between these variables by using _plat as
a suffix for them.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-12-13 16:51:09 -07:00
Simon Glass
d1998a9fde dm: treewide: Rename ofdata_to_platdata() to of_to_plat()
This name is far too long. Rename it to remove the 'data' bits. This makes
it consistent with the platdata->plat rename.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-12-13 16:51:09 -07:00
Simon Glass
caa4daa2ae dm: treewide: Rename 'platdata' variables to just 'plat'
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).

Rename some of the latter variables to end with 'plat' for consistency.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-12-13 16:51:08 -07:00
Simon Glass
41575d8e4c dm: treewide: Rename auto_alloc_size members to be shorter
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.

Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-12-13 08:00:25 -07:00
Simon Glass
f7ae49fc4f common: Drop log.h from common header
Move this header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 21:19:18 -04:00
Pratyush Yadav
0a9c287497 spi: cadence-qspi: Move ref clock calculation to probe
"assigned-clock-parents" and "assigned-clock-rates" DT properties take
effect only after ofdata_to_platdata() when clk_set_defaults() is called
in device_probe(). Therefore clk get rate() would return a wrong value
in ofdata_to_platdata() when compared with probe. Hence it needs to be
moved to probe.

Tested on u-boot-ti/next.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-04-29 01:44:35 +05:30
Simon Glass
336d4615f8 dm: core: Create a new header file for 'compat' features
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.

Move the compatibility features into a separate header file.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-02-05 19:33:46 -07:00
Simon Glass
61b29b8268 dm: core: Require users of devres to include the header
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
2020-02-05 19:33:46 -07:00
Vignesh Raghavendra
daa9405d7c spi: cadence-qspi: Add compatible for TI AM654
TI's AM654 SoC has a Cadence OSPI IP. Add a new compatible string for
the same.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-27 22:27:22 +05:30
Vignesh Raghavendra
0f247848b6 spi: cadence-qspi: Add support for Cadence Octal SPI controller
Cadence OSPI is similar to QSPI IP except that it supports Octal IO
(8 IO lines) flashes. Add support for Cadence OSPI IP with existing
driver using new compatible

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-27 22:27:22 +05:30
Vignesh Raghavendra
ffab212123 spi: cadence-qspi: Add direct mode support
Add support for Direct Access Controller mode of Cadence QSPI. This
allows MMIO access to SPI NOR flash providing better read performance.
Direct mode is only exercised if AHB window size is greater than 8MB.
Support for flash address remapping is also not supported at the moment
and can be added in future.

For better performance, driver uses DMA to copy data from flash in
direct mode using dma_memcpy().

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-27 22:27:22 +05:30
Vignesh Raghavendra
d640772021 spi: cadence_qspi: Move to spi-mem framework
Current Cadence QSPI driver has few limitations. It assumes all read
operations to be in Quad mode and thus does not support SFDP parsing.
Also, adding support for new mode such as Octal mode would not be
possible with current configuration. Therefore move the driver over to spi-mem
framework. This has added advantage that driver can be used to support
SPI NAND memories too.
Hence, move driver over to new spi-mem APIs.

Please note that this gets rid of mode bit setting done when
CONFIG_SPL_SPI_XIP is defined as there does not seem to be any user to
that config option.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-27 22:27:22 +05:30
Simon Goldschmidt
64c7c8c91c spi: cadence_qspi: support DM_CLK
Support loading clk speed via DM instead of requiring ad-hoc code.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20 23:46:11 +01:00
Simon Goldschmidt
46b633d7b4 spi: cadence_qspi: convert to livetree
Convert 'cadence_spi_ofdata_to_platdata' to use dev_read_* functions to
read driver parameters and 'dev_read_first_subnode'/'ofnode_read_*' to
read flash (child node) parameters.

Tested on socfpga_socrates (socfpga gen5).

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-05-10 22:48:11 +02:00
Simon Goldschmidt
ac7e14ae0d spi: cadence_qspi: add reset handling
This adds reset handling to the cadence qspi driver.

For backwards compatibility, only a warning is printed when failing to
get reset handles.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-04-17 22:20:17 +02:00
Ley Foon Tan
7eece32812 spi: cadence_qspi: Add quad write support
Use quad write if SPI_TX_QUAD flag is set.

Tested quad write on Stratix 10 SoC board (Micron
serial NOR flash, mt25qu02g)

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2019-04-12 10:54:03 +05:30
Simon Goldschmidt
2a3a99932b spi: cadence_qspi: use "cdns,qspi-nor" as compatible
Linux uses "cdns,qspi-nor" as compatible string for the cadence
qspi driver, so change driver, docs and all device trees.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2018-11-29 12:45:15 +01:00
Ley Foon Tan
9bd39dd8e5 spi: cadence_qspi: Fix compilation warning
Use "%zu" for size_t data type.

Compilation warning as below:

In file included from include/linux/bug.h:7:0,
                 from include/common.h:26,
                 from drivers/spi/cadence_qspi.c:8:
drivers/spi/cadence_qspi.c: In function ‘cadence_spi_xfer’:
drivers/spi/cadence_qspi.c:211:8: warning: format ‘%d’ expects argument of type ‘int’, but argument 3 has type ‘size_t {aka long unsigned int}’ [-Wformat=]
  debug("%s: len=%d [bytes]\n", __func__, data_bytes);
        ^
include/linux/printk.h:37:21: note: in definition of macro ‘pr_fmt’
 #define pr_fmt(fmt) fmt
                     ^~~
include/log.h:142:2: note: in expansion of macro ‘debug_cond’
  debug_cond(_DEBUG, fmt, ##args)
  ^~~~~~~~~~
drivers/spi/cadence_qspi.c:211:2: note: in expansion of macro ‘debug’
  debug("%s: len=%d [bytes]\n", __func__, data_bytes);

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
2018-07-12 09:22:11 +02:00
Ley Foon Tan
6c353674bd spi: cadence_qspi: Change to use devfdt_get_addr_index()
Change to use devfdt_get_addr_index() function to get fdt address.

Original code has compilation warning below:

drivers/spi/cadence_qspi.c: In function ‘cadence_spi_ofdata_to_platdata’:
drivers/spi/cadence_qspi.c:297:18: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
  plat->regbase = (void *)data[0];
                  ^
drivers/spi/cadence_qspi.c:298:18: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
  plat->ahbbase = (void *)data[2];
                  ^
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-06-04 23:30:04 +05:30
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
Jason Rush
15a70a5da3 spi: cadence_spi: Sync DT bindings with Linux
Adopt the Linux DT bindings. This also fixes an issue
with the indaddrtrig register on the Cadence QSPI
device being programmed with the wrong value for the
socfpga arch.

Tested on TI K2G platform:
Tested-by: Vignesh R <vigneshr@ti.com>

Tested on a socfpga-cyclonev board:
Tested-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>

Signed-off-by: Jason Rush <jarush@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Acked-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Acked-by: Marek Vasut <marex@denx.de>
2018-01-24 12:07:50 +05:30
Simon Glass
e160f7d430 dm: core: Replace of_offset with accessor
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-02-08 06:12:14 -07:00
Phil Edworthy
6d72810c66 spi: cadence_qspi: Move DT prop code to match layout
Move the code to read the "sram-size" property into the other code
that reads properties from the node, rather than the SF subnode.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:57:28 +01:00
Phil Edworthy
7d403f284c spi: cadence_qspi: Use spi mode at the point it is needed
Instead of extracting mode settings and passing them as separate
args to another function, just pass the SPI mode as an arg.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:57:27 +01:00
Masahiro Yamada
1221ce459d treewide: replace #include <asm/errno.h> with <linux/errno.h>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content.  (both just wrap <asm-generic/errno.h>)

Replace all include directives for <asm/errno.h> with <linux/errno.h>.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-23 17:55:42 -04:00
Jagan Teki
08fe9c294f spi: Use mode for rx mode flags
Make rx mode flags as generic to spi, earlier mode_rx is
maintained separately because of some flash specific code.

Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-09-22 01:02:28 +05:30
Vignesh R
2372e14f19 spi: cadence_quadspi: Enable QUAD mode based on DT data
Instead of relying on CONFIG_SPI_FLASH_QUAD to be defined to enable QUAD
mode, make use of mode_rx field of dm_spi_slave_platdata to determine
whether to enable or disable QUAD mode. This is necessary to support
muliple SPI controllers where one of them may not support QUAD mode.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09 20:16:33 +05:30
Chin Liang See
4e609b6cb1 spi: cadence_qspi: Ensure check for max frequency in place
Ensure the intended SCLK frequency not exceeding the maximum
frequency. If that happen, SCLK will set to maximum frequency.

Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Vikas Manocha <vikas.manocha@st.com>
Cc: Jagannadh Teki <jteki@openedev.com>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
2015-11-05 02:34:15 +01:00
Chin Liang See
040f4ba742 spi: cadence_qspi: Fix fdt read of spi-max-frequency
Fix the fdt read for spi-max-frequency as it's contained
in the child node. Current state of code is always
returning default value.

Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Vikas Manocha <vikas.manocha@st.com>
Cc: Jagannadh Teki <jteki@openedev.com>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
2015-11-05 02:34:15 +01:00
Chin Liang See
98fbd71d7a spi: cadence_qspi: Ensure spi_calibration is run when sclk change
Ensuring spi_calibration is run when there is a change of sclk
frequency. This will ensure the qspi flash access works for high
sclk frequency

Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Vikas Manocha <vikas.manocha@st.com>
Cc: Jagannadh Teki <jteki@openedev.com>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-11-05 02:34:15 +01:00
Vikas Manocha
90a2f71711 spi: cadence_qspi: get sram size from device tree
sram size could be different on different socs, e.g. on stv0991 it is 256 while
on altera platform it is 128. It is better to receive it from device tree.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
2015-07-03 13:50:53 +05:30
Simon Glass
19a25f672c dm: spi: Move the per-child data size to the uclass
This is common to all SPI drivers and specifies a structure used by the
uclass. It makes more sense to define it in the uclass.

Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
2015-01-29 17:09:55 -07:00
Axel Lin
1dc7d00f27 spi: cadence_qspi: Fix checking return value of fdt_first_subnode()
fdt_first_subnode() returns -FDT_ERR_NOTFOUND if no subnode found.
0 is supposed to be a valid offset returns from fdt_first_subnode().

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2015-01-07 12:30:54 +05:30
Stefan Roese
10e8bf88c0 spi: Add Cadence QSPI DM driver used by SoCFPGA
This driver is cloned from the Altera Rockerboard.org U-Boot
repository. I used this git tag: ACDS14.0.1_REL_GSRD_RC2. With Some
modification to support the U-Boot driver model (DM).

As mentioned above, in this new version I ported this driver to the
new driver model (DM). One big advantage of this move is that now
multiple SPI drivers can be enabled on one platform. And since the
SoCFPGA also has the Designware SPI master controller integrated,
this feature is really needed to support both controllers.

Because of this, this series needs the DT support for SoCFPGA
to be applied. For DT based probing in the SPI DM.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2014-12-06 13:52:46 +01:00