Either the USB and Fastboot were never finished, or somehow it got
lost. This puts enough hooks back into omap3logic to enable
fastboot and hopefully prepare it for Kconfig conversion.
Signed-off-by: Adam Ford <aford173@gmail.com>
Fix the building warning as below:
---8<----
Warning (reg_format): "reg" property in /i2c-gpio-0/pcf8563@50 has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells value for /i2c-gpio-0/pcf8563@50
Warning (avoid_default_addr_size): Relying on default #size-cells value for /i2c-gpio-0/pcf8563@50
--->8----
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Some device the serial console's initialization cannot run early during
the boot process. Hence, nulldev serial device is helpful on that
situation.
For example, if the serial module was implemented in FPGA. Serial
initialization is prohibited to run until the FPGA was programmed.
This commit is to adding nulldev serial driver. This will allows the
default console to be specified as a nulldev.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Keng Soon Cheah <keng.soon.cheah@ni.com>
Cc: Chen Yee Chew <chen.yee.chew@ni.com>
With debug enabled, SPL output following these debug prints is on the
same line and it is hard to read. Fix it.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
DRA71x processors are reduced pin and software compatible
derivative of DRA72 processors. Add support for detection
of SR2.1 version of DRA71x family of processors.
Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Like the OMAP-L138 LCDK before it, let's move the da850-evm and
the variations to TI_COMMON_CMD_OPTIONS to cut back one some of the
defconfig entries.
Signed-off-by: Adam Ford <aford173@gmail.com>
Some drivers in Linux (ex. drivers/mtd/nand/denali.c) use
ioread*/iowrite* accessors. Import them to make drivers more
synced. I copied code from include/asm-generic/io.h of Linux.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Import include/linux/dma-direction.h from Linux 4.13-rc7 and delete
duplicated definitions of enum dma_data_direction.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Enable TI_COMMON_CMD_OPTIONS and remove similar options
from the defconfig. Updated with savedefconfig.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
Much of the AM3517 functions are copies of the standard definitions
used in ti_omap3_common.h. Moving to include a common file
reduces the amount of duplicative code and clutter. A few
AM3517 specific functions (like EMIF4) are explictly defined
and a few items are undefined or redefined, but overall the number
of lines of code shink.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
Add space around operator "+", make it
match the coding style.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Macro VA_BITS and PTE_BLOCK_BITS are not used
in the code, so remove them.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add the new compatible "atmel,24mac402" to accommodate AT24MAC402.
The AT24MAC402 is a 2K Serial EEPROM and the 2-Kbit memory array
is internally organized as 16 pages of 16 bytes of EEPROM each.
The 48-bit EUI address in the AT24MAC402 are located in the extended
memory block.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Add the new compatible "microchip,24aa02e48" to accommodate 24AA02E48,
the 24AA02E48 is a 2K I2C Serial EEPROM with pre-programmed globally
unique, 48-bit node address, and 8-byte page size.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
The PMMC firmware should be bundled with the FIT image for HS devices,
remove the steps that load and install this firmware outside of FIT.
Signed-off-by: Andrew F. Davis <afd@ti.com>
The PMMC firmware should be bundled into a FIT image on HS
devices to allow authentication/decryption, add a handler to
process this PMMC firmware.
Signed-off-by: Andrew F. Davis <afd@ti.com>
This works (roughly) the same way as linux's, but we currently always
print lower-case (ie. we just keep %pUB and %pUL for compat with linux),
mostly just because that is what uuid_bin_to_str() supports.
%pUb: 01020304-0506-0708-090a-0b0c0d0e0f10
%pUl: 04030201-0605-0807-090a-0b0c0d0e0f10
It will be used by a later efi_loader paths for efi variables and for
device-path-to-text protocol, and also quite useful for debug prints
of protocol GUIDs.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is convenient for efi_loader which deals a lot with UTF-16. Only
enabled with CC_SHORT_WCHAR, leaving room to add a UTF-32 version when
CC_SHORT_WCHAR is not enabled.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
EFI_LOADER really wants UTF-16 strings (ie. %ls and L"string" are 16bit
chars instead of 32bit chars). But rather than enabling -fshort-wchar
conditionally if EFI_LOADER is enabled, it was deemed preferrable to
globally switch.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This allows to scan the DT including all "clocks" node's sub-nodes
in which fixed-clock are defined.
All fixed-clock should be defined inside a clocks node which collect all
external oscillators. Until now, all clocks sub-nodes can't be binded except
if the "simple-bus" compatible string is added which is a hack.
Update test.dts by moving clk_fixed node inside clocks.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently, all fixed-clock declared in "clocks" node in device tree
can be binded by clk_fixed_rate.c driver only if each of them have
the "simple-bus" compatible string.
This constraint has been invoked here [1].
This patch offers a solution to avoid adding "simple-bus" compatible
string to nodes that are not busses.
[1] https://patchwork.ozlabs.org/patch/558837/
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for reading a list of bouncing addresses from a in-tree file
(doc/bounces) and from the ~/.patman config file. These addresses are
stripped from the Cc list.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com <mailto:philipp.tomsich@theobroma-systems.com>>
Adjust this code so that it can work with Python 2 and 3.
Fixes: d73fcb1 (moveconfig: Support building a simple config database)
Reported-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a convenience macro to iterate over subnodes of a node. Make use of
this where appropriate in the code.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we sometimes see warnings of the form:
/tmp/tmpMA89kB:36: warning: overriding the value of CMD_SPL.
Old value: "y", new value: "y".
This is not very useful as it does not show whch defconfig file it relates
to. Update the tool to show this.
Signed-off-by: Simon Glass <sjg@chromium.org>
We can use printf() to limit the string width. Adjust the code to do this
instead of using strlcpy() which is a bit clumbsy.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Convert SANDBOX_BITS_PER_LONG to Kconfig and assign it a correct
number depending on which host we are going to build and run.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It seems most of the time we are building and running sandbox on 64-bit host.
But we do support 32-bit host as well. Introduce Kconfig option for this.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is an overflow problem when taking the size instead of the number
of blocks in blk_create_device(). This results in a wrong device size: the
device apparent size is its real size modulo 4GB.
Using the number of blocks instead of the device size fixes the problem and
is more coherent with the internals of the block layer.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This option is an SPL-variant of the I2C_EEPROM option to enable
the driver for generic I2C-attached EEPROMs for SPL.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the code to set the ethernet mac address from eeprom by using
the common code from the common folder.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Replace the code to set the ethernet mac address with the code from
the common folder.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Create board/$(VENDOR)/common folder to accommodate the common code
shared by other atmel boards, now put the code to set ethernet mac
address from eeprom, which uses the i2c eeprom driver.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for selecting proper dtb for
am57xx BeagleBoard X15 revC u-boot from FIT
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
AM571x supports DDR running at 666MHz. Right now it is
clocked at 532MHz which is lower than what is supported.
In order to have maximum performance on AM571-IDK,
switch DDR to 666MHz.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for selecting proper dtb for
dra76x u-boot from FIT.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Separate out u-boot specific compatibles from dts files.
This will help in syncing dts files in future.
Also these will get deleted eventually once respective drivers
are capable of handling Linux dts files.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adding pinmux and IODELAY data for dra76-evm.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
