Commit graph

33 commits

Author SHA1 Message Date
Dan Murphy
d861a333da ARM: OMAP5: Add registers and defines for USBOTG SS
Add the prcm registers and the bit definitions to enable the
USB SS port of the OMAP5 device.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-20 23:42:39 +02:00
Lokesh Vutla
e22cc0cf13 ARM: OMAP5: Avoid writing into LDO SRAM bits
Writing magic bits into LDO SRAM was suggested only for OMAP5432
ES1.0. Now these are no longer applicable. Moreover these bits should
not be overwritten as they are loaded from EFUSE. So avoid
writing into these registers.

Boot tested on OMAP5432 ES2.0

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-09-20 16:57:40 -04:00
Lokesh Vutla
65e9d56fb9 ARM: DRA7xx: Lock DPLL_GMAC
Locking DPLL_GMAC

[mugunthanvnm@ti.com:Configure only if CPSW is selected]

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2013-07-26 16:39:11 -04:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Lokesh Vutla
97405d843e ARM: DRA7xx: clocks: Update PLL values
Update PLL values.
SYS_CLKSEL value for 20MHz is changed to 2. In other platforms
SYS_CLKSEL value 2 represents reserved. But in sys_clk array
ind 1 is used for 13Mhz. Since other platforms are not using
13Mhz, reusing index 1 for 20MHz.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
2013-06-10 08:43:10 -04:00
Nishanth Menon
18c9d55ac6 ARM: OMAP5: DRA7xx: support class 0 optimized voltages
DRA752 now uses AVS Class 0 voltages which are voltages in efuse.

This means that we can now use the optimized voltages which are
stored as mV values in efuse and program PMIC accordingly.

This allows us to go with higher OPP as needed in the system without
the need for implementing complex AVS logic.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:10 -04:00
Lokesh Vutla
3332b24421 ARM: DRA7xx: clocks: Fixing i2c_init for PMIC
In DRA7xx Soc's voltage scaling is done using GPI2C.
So i2c_init should happen before scaling. I2C driver
uses __udelay which needs timer to be initialized.
So moving timer_init just before voltage scaling.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:09 -04:00
Lokesh Vutla
63fc0c775c ARM: DRA7xx: power Add support for tps659038 PMIC
TPS659038 is the power IC used in DRA7XX boards.
Adding support for this and also adding pmic data
for DRA7XX boards.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:09 -04:00
Lokesh Vutla
4ca94d8186 ARM: OMAP4+: pmic: Make generic bus init and write functions
Voltage scaling can be done in two ways:
-> Using SR I2C
-> Using GP I2C
In order to support both, have a function pointer in pmic_data
so that we can call as per our requirement.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:09 -04:00
Lokesh Vutla
af1d002f89 ARM: OMAP2+: Rename asm/arch/clocks.h asm/arch/clock.h
To be consistent with other ARM platforms,
renaming asm/arch-omap*/clocks.h to asm/arch-omap*/clock.h

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:09 -04:00
Andrii Tseglytskyi
e69c585d76 OMAP5: add ABB setup for MPU voltage domain
Patch adds a call of abb_setup() function, and proper registers
definitions needed for ABB setup sequence. ABB is initialized
for MPU voltage domain.

Signed-off-by: Andrii Tseglytskyi <andrii.tseglytskyi@ti.com>
2013-06-10 08:43:09 -04:00
Lokesh Vutla
0b1b60c779 ARM: OMAP5: Fix warm reset with USB cable connected
Warm reset on OMAP5 freezes when USB cable is connected.
Fix requires PRM_RSTTIME.RSTTIME1 to be programmed
with the time for which reset should be held low for the
voltages and the oscillator to reach stable state.

There are 3 parameters to be considered for calculating
the time, which are mostly board and PMIC dependent.
-1- Time taken by the Oscillator to shut + restart
-2- PMIC OTP times
-3- Voltage rail ramp times, which inturn depends on the
PMIC slew rate and value of the voltage ramp needed.

In order to keep the code in u-boot simple, have a way
for boards to specify a pre computed time directly using
the 'CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC'
option. If boards fail to specify the time, use a default
as specified by 'CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC' instead.
Using the default value translates into some ~22ms and should work in
all cases.
However in order to avoid this large delay hiding other bugs,
its recommended that all boards look at their respective data
sheets and specify a pre computed and optimal value using
'CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC'

In order to help future board additions to compute this
config option value, add a README at doc/README.omap-reset-time
which explains how to compute the value. Also update the toplevel
README with the additional option and pointers to
doc/README.omap-reset-time.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[rnayak@ti.com: Updated changelog and added the README]
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
2013-05-10 08:25:55 -04:00
Lubomir Popov
a8f408a8c4 OMAP: Fix copy-paste bug that did not enable UART4 clock
V2 fixes line wrap issue of the patch itself.

UART3 was enabled twice instead of UART4.

One more cosmetic change in a comment on EMIF clock.

Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
Reviewed-by: R Sricharan <r.sricharan@ti.com>
2013-04-08 11:29:05 -04:00
Lokesh Vutla
ea8eff1fe0 arm: dra7xx: clock: Add the dplls data
A new DPLL DDR is added in DRA7XX socs. Now clocks to
EMIF CD is from DPLL DDR. So DPLL DDR should be locked
before initializing RAM.
Also adding other dpll data which are different from OMAP5 ES2.0.
SYS_CLK running at 20MHz is introduced in DRA7xx socs.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11 11:06:11 -04:00
SRICHARAN R
47abc3df70 ARM: OMAP4/5: clocks: Add the required OPP settings as per the latest addendum
Change OPP settings as per the latest 0.5 version of
addendum for OMAP5430 ES2.0. omap4/hw_data.c is touched
here to add dummy dividers.

While here correcting OPP_NOM mpu, core frequency for
OMAP4430 ES2.x

Note that OMAP5430 ES1.0 support is still kept alive and
would be removed in a cleanup later.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Cc: Tom Rini <trini@ti.com>
Cc: Nishanth Menon <nm@ti.com>
2013-03-11 11:06:10 -04:00
SRICHARAN R
3fcdd4a5f8 ARM: OMAP4+: Clean up the pmic code
The pmic code is duplicated for OMAP 4 and 5.
Instead move the data to Soc specific place and
share the code.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11 11:06:10 -04:00
SRICHARAN R
ee9447bfe3 ARM: OMAP4+: Cleanup the clocks layer
Currently there is quite a lot of code which
is duplicated in the clocks code for OMAP 4 and 5
Socs. Avoiding this here by moving the clocks
data to a SOC specific place and the sharing the
common code.

This helps in addition of a new Soc with minimal
changes.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11 11:06:09 -04:00
SRICHARAN R
01b753ff7b ARM: OMAP4+: Change the PRCM structure prototype common for all Socs
The current PRCM structure prototype directly matches the hardware
register layout. So there is a need to change this for every new silicon
revision which has register space changes.

Avoiding this by making the prototye generic and populating the register
addresses seperately for all Socs.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-03-11 11:06:09 -04:00
Lokesh Vutla
9ca8bfea80 ARM: OMAP4+: emif: Detect SDRAM from SDRAM config register
Now SDRAM initialization is done on the basis of omap revision.
Instead this should be done on basis of SDRAM type read from
EMIF_SDRAM_CONFIG register. This will be helpful to avoid
unnessecary cpu checks for new boards

Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11 11:06:09 -04:00
Lokesh Vutla
753bae8c5d OMAP5: DPLL core lock for OMAP5432
No need to Unlock DPLL initially.
DDR3 can work at normal OPP from initialozation

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2012-07-07 14:07:24 +02:00
SRICHARAN R
8de17f4617 OMAP5: palmas: Configure nominal opp vdd values
The nominal opp vdd values as recommended for
ES1.0 silicon is set for mpu, core, mm domains using palmas.

Also used the right sequence to enable the vcores as per
a previous patch from Nishant Menon, which can be dropped now.
	http://lists.denx.de/pipermail/u-boot/2012-March/119151.html

Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15 08:31:23 +02:00
SRICHARAN R
f40107345c OMAP5: emif/ddr: Change emif settings as required for ES1.0 silicon.
The OMAP5 silicon has new DDR PHY design, which includes a external PHY
as well. So configuring the ext PHY parameters here. Also the EMIF timimg
registers and a couple of DDR mode registers needs to be updated based on
the testing from the actual silicon.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15 08:31:23 +02:00
SRICHARAN R
5f14d9197e OMAP5: clocks: Change clock settings as required for ES1.0 silicon.
Aligning all the clock related settings like the dpll frequencies, their
respective clock outputs, etc to the ideal values recommended for
OMAP5430 ES1.0 silicon.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15 08:31:23 +02:00
Nishanth Menon
3acb553439 OMAP4460: TPS Ensure SET1 is selected after voltage configuration
TPS SET0/SET1 register is selected by a GPIO pin on OMAP4460 platforms.
Currently we control this pin with a mux configuration as part of
boot sequence.
Current configuration results in the following voltage waveform:
                           |---------------| (SET1 default 1.4V)
                           |               --------(programmed voltage)
                           | <- (This switch happens on mux7,pullup)
vdd_mpu(TPS)         -----/ (OPP boot voltage)
                                             --------- (programmed voltage)
vdd_core(TWL6030)    -----------------------/ (OPP boot voltage)
Problem 1)                |<----- Tx ------>|
   timing violation for a duration Tx close to few milliseconds.
Problem 2) voltage of MPU goes beyond spec for even the highest of MPU OPP.

By using GPIO as recommended as standard procedure by TI, the sequence
changes to:
                                  -------- (programmed voltage)
vdd_mpu(TPS)         ------------/ (Opp boot voltage)
                                   --------- (programmed voltage)
vdd_core(TWL6030)    -------------/ (OPP boot voltage)

NOTE: This does not attempt to address OMAP5 - Aneesh please confirm

Reported-by: Isabelle Gros <i-gros@ti.com>
Reported-by: Jerome Angeloni <j-angeloni@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
2012-05-15 08:31:22 +02:00
Nishanth Menon
a78274b205 OMAP3+: Introduce generic logic for OMAP voltage controller
OMAP Voltage controller is used to generically talk to
PMICs on OMAP3,4,5 over I2C_SR. Instead of replicating code
in multiple SoC code, introduce a common voltage controller
logic which can be re-used from elsewhere.

With this change, we replace setup_sri2c with omap_vc_init which
has the same functionality, and replace the voltage scale
replication in do_scale_vcore and do_scale_tps62361 with
omap_vc_bypass_send_value. omap_vc_bypass_send_value can also
now be used with any configuration of PMIC.

NOTE: Voltage controller controlling I2C_SR is a write-only data
path, so no register read operation can be implemented.

Reported-by: Isabelle Gros <i-gros@ti.com>
Reported-by: Jerome Angeloni <j-angeloni@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
2012-05-15 08:31:22 +02:00
Anatolij Gustschin
27ac87d91e arch/arm/cpu/armv7/omap-common/clocks-common.c: Fix build warnings
Fix:
clocks-common.c: In function 'setup_non_essential_dplls':
clocks-common.c:323:6: warning: variable 'sys_clk_khz' set but not used
[-Wunused-but-set-variable]
clocks-common.c: In function 'setup_non_essential_dplls':
clocks-common.c:323:6: warning: variable 'sys_clk_khz' set but not used
[-Wunused-but-set-variable]

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Tom Rini <trini@ti.com>
2012-03-29 08:19:29 +02:00
Govindraj.R
860004c103 OMAP4: clock-common: Move the usb dppl configuration to new func
usb dpll configuration is done only part of non-essential
dppl configuration however if CONFIG_USB_EHCI_OMAP is defined
we may have to configure usb dpll's for proper functioning
of usb modules. So move the usb dppl configuration to a new func.
and utilise the same during essential dpll configuration.

Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Tested-by: Stefano Babic <sbabic@denx.de>
2012-02-12 10:11:31 +01:00
Anatolij Gustschin
164a750789 arch/arm/cpu/armv7/omap-common/clocks-common.c: Fix GCC 4.6 warnings
Fix:
clocks-common.c: In function 'setup_dplls':
clocks-common.c:256:6: warning: variable 'sysclk_ind' set but not used
[-Wunused-but-set-variable]
clocks-common.c: In function 'setup_non_essential_dplls':
clocks-common.c:292:6: warning: variable 'sysclk_ind' set but not used
[-Wunused-but-set-variable]

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: sricharan <r.sricharan@ti.com>
Cc: Tom Rini <trini@ti.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Tom Rini <trini@ti.com>
2011-12-06 23:59:40 +01:00
Aneesh V
cd5847ac3a omap4460: fix TPS initialization
TPS power IC is controlled using a GPIO (gpio_wk7).
This GPIO should be maintained at logic 1 always. As
such an internal pull-up on this pin will do the job,
driving the GPIO outuput is not needed. This will avoid
the need of using GPIO library in SPL and also may
save some power.

Signed-off-by: Aneesh V <aneesh@ti.com>
2011-12-06 23:59:34 +01:00
Sricharan
78f455c055 omap4/5: Add support for booting with CH.
Configuration header(CH) is 512 byte header attached to an OMAP
boot image that will help ROM code to initialize clocks, SDRAM
etc and copy U-Boot directly into SDRAM. CH can help us in
by-passing SPL and directly boot U-boot, hence it's an alternative
for SPL. However, we intend to support both CH and SPL for OMAP4/5.

Initialization done through CH is limited and is not equivalent
to that done by SPL. So U-Boot has to distinguish between the
two cases and handle them accordingly. This patch takes care
of doing this.

Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-15 22:25:50 +01:00
Sricharan
2e5ba48928 omap5: clocks: Add clocks support for omap5 platform.
Adding the correct configurations required for
dplls, clocks, for omap5 Soc.

Also changes are done to retain some part of the code common
for OMAP4/5 and move only the remaining to the Soc specific
directories.

Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-15 22:25:50 +01:00
Sricharan
508a58fa8e omap5: Add minimal support for omap5430.
This patch adds the minimal support for OMAP5. The platform and machine
specific headers and sources updated for OMAP5430.

OMAP5430 is Texas Instrument's SOC based on ARM Cortex-A15 SMP architecture.
It's a dual core SOC with GIC used for interrupt handling and SCU for cache
coherency.

Also moved some part of code from the basic platform support that can be made
common for OMAP4/5. Rest is kept out seperately. The same approach is followed
for clocks and emif support in the subsequent patches.

Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-15 22:25:50 +01:00
Sricharan
ce170beeb7 omap4: make omap4 code common for future reuse
Much of omap4 soc support code can be reused for omap5.
Move them to the omap-common directory to facilitate
this.

Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-15 22:25:50 +01:00
Renamed from arch/arm/cpu/armv7/omap4/clocks.c (Browse further)