The commit was added as a workaround required in QEMU when using BBL as
the supervisor binary interface (SBI) for Linux. We are now using
OpenSBI to provide the SBI, the workaround is therefore not required
anymore and can be removed.
This reverts commit 897206c5cc.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
A number of board function belong in init.h with the others. Move them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add two new configurations (qemu-riscv{32,64}_spl_defconfig) with SPL
enabled for RISC-V QEMU. QEMU does not require SPL to run U-Boot. The
configurations are meant to help the development of SPL on RISC-V.
The configurations enable RAM as the only SPL boot device. Images must
be loaded at address 0x80200000. In the default boot flow, U-Boot SPL
starts in machine mode, loads the OpenSBI FW_DYNAMIC firmware and U-Boot
proper from the supplied FIT image, and starts OpenSBI. U-Boot proper is
then started in supervisor mode by OpenSBI.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Move env_set_hex() over to the new header file along with env_set_addr()
which uses it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
QEMU specifies the location of Linux (supplied with the -kernel
argument) in the device tree using the riscv,kernel-start and
riscv,kernel-end properties. We currently rely on the SBI implementation
of BBL to run Linux and therefore embed Linux as payload in BBL. This
causes an issue, because BBL detects the kernel properties in the device
tree and ignores the Linux payload as a result.
Work around this issue by clearing the kernel properties in the device
tree before booting Linux.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
QEMU embeds the location of the kernel image in the device tree. Store
this address in the environment as variable kernel_start. It is used in
the board-local distro boot command QEMU to boot the kernel with the
U-Boot device tree. The QEMU boot command is added as the first boot
target device.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
QEMU provides a device tree, which is passed to U-Boot using register
a1. We are now able to directly select the device tree with the
configuration CONFIG_OF_PRIOR_STAGE. Replace the hard-coded address in
qemu-riscv with it.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Currently devices on the virtio bus is not automatically enumerated,
which means peripherals on the virtio bus are not discovered by their
drivers. This uses board_init() to do the virtio enumeration.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds QEMU RISC-V 'virt' board target support, with the hope of
helping people easily test U-Boot on RISC-V.
The QEMU virt machine models a generic RISC-V virtual machine with
support for the VirtIO standard networking and block storage devices.
It has CLINT, PLIC, 16550A UART devices in addition to VirtIO and
it also uses device-tree to pass configuration information to guest
software. It implements RISC-V privileged architecture spec v1.10.
Both 32-bit and 64-bit builds are supported. Support is pretty much
preliminary, only booting to U-Boot shell with the UART driver on
a single core. Booting Linux is not supported yet.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
