spi-rx-bus-width property is part of flash, so it should be moved
to flash node from qspi node. This patch fixes the incorrect read
of spi-rx-bus-width property by moving it to flash node.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The VCU disable bit(8) in IP disable register of efuse
is valid only if PL powered up and hence PL powerup status
has to be considered while determining the CG part also.
This patch considers the PL powerup status and ignores the VCU
disable bit if PL not powered up.
This fixes the issue of "unknown" id for CG parts if PL not powered up
and VCU bit(8) is not set.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
AndeStar RISC-V(V5) provide mcache_ctl register which
can configure I/D cache as enabled or disabled.
This CSR will be encapsulated by CONFIG_RISCV_NDS.
If you want to configure cache on AndeStar V5
AE350 platform. YOu can enable [*] AndeStar V5 ISA support
by make menuconfig.
This approach also provide the expansion when the
vender specific features are going to join in.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Add ae350_32.dts for 32 bit. And also rename
ae350.dts to ae350_64.dts for 64 bit.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Separate ax25-ae350 from one to two for
32 and 64 bit individually. And also select
different dts for 32 and 64 bit.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Use same dts to boot U-Boot and Kernel.
Following are the change notes :
1 Remove early printk bootargs.
2 Timer frequency are changed to 60MHz.
3 Add dma, snd, lcd, virtio nodes which are used
in kernel drivers. They does not been used by U-Boot.
4 Change spi irq from 3 to 4.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
QEMU specifies the location of Linux (supplied with the -kernel
argument) in the device tree using the riscv,kernel-start and
riscv,kernel-end properties. We currently rely on the SBI implementation
of BBL to run Linux and therefore embed Linux as payload in BBL. This
causes an issue, because BBL detects the kernel properties in the device
tree and ignores the Linux payload as a result.
Work around this issue by clearing the kernel properties in the device
tree before booting Linux.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
QEMU embeds the location of the kernel image in the device tree. Store
this address in the environment as variable kernel_start. It is used in
the board-local distro boot command QEMU to boot the kernel with the
U-Boot device tree. The QEMU boot command is added as the first boot
target device.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Enable distro boot on the qemu-riscv32/64 boards. Supported boot target
devices are VirtIO and DHCP.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Add a boot command to distro boot to support disks connected over the
VirtIO bus. The boot command uses the shared block environment.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
The bootm implementation of RISC-V diverges from that of other
architectures. Update it to match the implementation of other
architectures. The ARM implementation is used as a reference.
This adds the following features and changes to RISC-V.
* Add support for the BOOTM_STATE_OS_FAKE_GO command
* Call the remove function on devices with the removal flag set before
booting Linux
* Force disconnect USB devices from the host before booting Linux
* Print and add bootstage information to the device tree before booting
Linux
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Support booting Linux (as payload of BBL) from FIT images. For this, the
default CONFIG_SYS_BOOTM_LEN is increased to 16 MB, and the environment
variables fdt_high and initrd_high are set to mark the device tree and
initrd as in-place.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
QEMU provides a device tree, which is passed to U-Boot using register
a1. We are now able to directly select the device tree with the
configuration CONFIG_OF_PRIOR_STAGE. Replace the hard-coded address in
qemu-riscv with it.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Store the hart ID and device tree passed by the prior boot stage (in a0
and a1) in registers s0 and s1. Replace one use of s1 in start.S to
avoid overwriting it.
The device tree is also stored in memory to make it available to U-Boot
with the configuration CONFIG_OF_PRIOR_STAGE.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The mstatus CSR includes WPRI (writes preserve values, reads ignore
values) fields and must therefore not be set to zero without preserving
these fields. It is not apparent why mstatus is set to zero here since
it is not required for U-Boot to run. Remove it.
This instruction and others encode zero as an immediate. RISC-V has the
zero register for this purpose. Replace the immediates with the zero
register.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The labels nmi_vector, trap_vector and handle_reset in start.S are not
used for RISC-V. Remove them.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is now deprecated and no board is using it. Drop it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
The machine trap-vector base address (mtvec) must be aligned on a 4-byte
boundary. Add the necessary align directive to trap_entry.
This patch also removes the global directive for trap_entry, which is
not required.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
start.S uses both tabs and spaces after instructions. Fix this by only
using tabs after instructions.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Implement the functions invalidate_icache_range() and
invalidate_icache_all().
RISC-V does not have instructions for explicit cache-control. The
functions in this patch are implemented with the memory ordering
instruction for synchronizing the instruction and data streams. This may
be implemented as a cache flush or invalidate on simple processors,
others may only invalidate the relevant cache lines.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Hang on unhandled exceptions to prevent execution in a faulty state.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Undefined exception codes currently lead to an out-of-bounds array
access. Prevent this by treating undefined exception codes as
"reserved".
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Only the first four exception codes are defined. Add the missing
exception codes from the definition in RISC-V Privileged Architecture
Version 1.10.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
RISC-V U-Boot reimplements the generic io functions from
asm-generic/io.h. Remove the redundant implementation and include the
generic io.h instead.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Replace the barrier functions in arch/riscv/include/asm/io.h with those
defined in barrier.h, which is imported from Linux. This version is
modified to remove the include statement of asm-generic/barrier.h, which
is not available in U-Boot or required.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The RISC-V arch incorrectly uses 32-bit instead of 64-bit variables in
several places. Fix this.
In addition, BITS_PER_LONG is set to 64 on RV64I systems.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enable the -fdata-sections compiler option for RISC-V. Buildman reports
the binary size decrease from this as 8365.3 bytes.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Use the new Kconfig entries to construct the ISA string for the -march
compiler flag. The -mabi compiler flag is selected based on the base
integer instruction set.
With this change, the C (compressed instructions) ISA extension is now
enabled for all boards with CONFIG_RISCV_ISA_C set. Buildman reports a
decrease in binary size of 71590 bytes.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add Kconfig entries for the C (compressed instructions) and A (atomic
instructions) ISA extensions. Only the C ISA extension is selectable.
This matches the configuration in Linux.
The Kconfig entries are not used yet. A follow-up patch will select the
appropriate compiler flags based on the Kconfig configuration.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
CONFIG_PHYS_64BIT should be enabled on RV64I systems. Select it.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
RISC-V defines the base integer instruction sets as RV32I and RV64I.
Rename CPU_RISCV_32 and CPU_RISCV_64 to ARCH_RV32I and ARCH_RV64I to
match this convention.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
This patch adds MT7629 qspi driver for accessing SPI NOR flash.
Signed-off-by: Guochun Mao <guochun.mao@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The Amlogic Meson SoCs embeds a Flash oriented SPI Controller name SPIFC.
This driver, ported from the Linux meson-spi-spifc driver, add support
for this controller on the Amlogic Meson GX SoCs in U-Boot.
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add test to regmap_read_poll_timeout() helper to check the timeout works
properly but cannot test proper condition matching since read/write calls
are not executed in sandbox.
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the regmap_read_poll_timeout() macro based on the Linux implementation
to simplify register polling with configurable timeout and sleep.
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Better buildman warning handling
Misc other things
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlv19KwRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreaWtwf/Xq0DuDuTyoqfVuGJk/SyS4PzZ7Z778oz
YxX7Do0biHMqT+3QnvhRGsYQQck2jOqP/Romr/U3q1+jDRT53/RDBnJmG4lQ/toF
79mShpx5vm/QZKf1QI1nJv57P1xRrP8VcDaqrHKsJ5v5sAaPls5y0ik+IzfSVlJX
mw0rs1cSKeoDKXu7a8AnP2OPJPhGT0C9Gougg5nnjyAwTs2dww8w396vyZmw0S3m
KnAOrvxrVGx7AxQFeD1T0/Fvc4jWrR82HBcibuYLuSSxFtnt26iEWfaP9CjKeV6h
P5/T3vxFolKesyG+2/OVeIlTvISHeXmsdYBpVtxDbHETWzxU0xDzzQ==
=SRxW
-----END PGP SIGNATURE-----
Merge tag 'pull-tg18' of git://git.denx.de/u-boot-dm
Various minor sandbox improvements
Better buildman warning handling
Misc other things
Some boards have the EMAC TX/RX lanes wired with a different length with
the clock lane, which can be workarounded by setting a TX/RX delay in
the EMAC.
This kind of delays are already defined in the newest device tree
binding of dwmac-sun8i, which has already entered linux-next.
Add support for setting these delays.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@openedev.com>
When we initialize the memory we need to autodetect rank and size
but this can happen only if we send the proper reset to both
memory module including cke signal.
For this reason we need initialize the physical on both channel because
we need to presume that both are connected. This way let the CLKE to be
activated at the right time with the memory reset coming from the cpu
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Using new mode improves stability of eMMC and SD cards. Without
it SPL fails to load u-boot from SD on Pinebook.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
Reviewed-by: Jagan Teki <jagan@openedev.com>
Comment in Linux driver says that clock needs to be doubled only
if we use DDR modes, moreover divider has to be set accordingly.
U-boot driver doesn't declare support for any DDR modes and doesn't
set internal clock divider in CLKCR, so it doubles clock
unconditionally when new mode is used.
Some cards can't handle that and as result SPL fails to load u-boot.
Fixes: de9b1771c3 ("mmc: sunxi: Support new mode")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
Allwinner A64 has new mode but doesn't have a mode switch in CCM,
and CCM_MMC_CTRL_MODE_SEL_NEW is not defined, so compilation fails
if MMC_SUNXI_HAS_NEW_MODE is enabled
Introduce new MMC_SUNXI_HAS_MODE_SWITCH option to be able to ifdef usage
of CCM_MMC_CTRL_MODE_SEL_NEW
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
[jagan: update commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
Its only called from this file, so make it static. While at it, remove
some occurances of multiple blank lines as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The initial layout for such NAND chips was the following:
+----------------------------------------------------------------------------+
| 1024 (data) | 30 (ECC) | 1024 (data) | 30 (ECC) | 32 (free OOB) | 30 (ECC) |
+----------------------------------------------------------------------------+
This layout has a weakness: reading empty pages trigger ECC errors
(this is expected), but the hardware ECC engine tries to correct the
data anyway and creates itself bitflips, hence bitflips are detected
in erased pages while actually there are none in the NAND chip.
Two solutions have been found at the same time. One was to enlarge the
free OOB area to 64 bytes, changing the layout to be:
+----------------------------------------------------------------------------+
| 1024 (data) | 30 (ECC) | 1024 (data) | 30 (ECC) | 64 (free OOB) | 30 (ECC) |
+----------------------------------------------------------------------------+
^^
The very big drawbacks of this solution are:
1/ It prevents booting from NAND.
2/ The current Linux driver (marvell_nand) does not have such problem
because it already re-reads possible empty pages in raw mode before
checking for bitflips. Using different layouts in U-Boot and Linux
would simply not work.
As this driver does support raw reads now and uses it to check for
empty pages, let's forget about this broken hack and return to the
initial layout with only 32 free OOB bytes.
Fixes: ac56a3b30c ("mtd: nand: pxa3xx: add support for 2KB 8-bit flash")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
This only applies on BCH path.
When an empty page is read, it triggers an uncorrectable error. While
this is expected, the ECC engine might produce itself bitflips in the
read data under certain layouts. To overcome this situation, always
re-read the entire page in raw mode and check for the whole page to be
empty.
Also report the right number of bitflips if there are any.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Raw read support is added by editing a few code sections:
->handle_data_pio() includes the ECC bytes that are not consumed
anymore by the ECC engine.
->prepare_set_command() is changed so that the ECC bytes are
requested as part of the data I/O length.
->drain_fifo() shall also avoid checking the R/B pin too often
when in raw mode.
->read_page_raw()/->read_oob_raw() are written from scratch.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
It is useful to obtain the block-protect setting of the SPI flash, so we
know whether it is fully open or (perhaps partially) write-protected. Add
a method for this. Update the sandbox driver to process this operation and
add a test.
Signed-off-by: Simon Glass <sjg@chromium.org>
