roc-rk3399-pc has some specific requirements to support LEDS,
environment. board detection and etc prior to U-Boot proper.
So as of now SPL would be a better stage for these custom board
requirements to support unlike TPL. Adding few of these custom
requirements like LEDS in TPL would require extra code pulling
and also the size of TPL can grow.
So, this patch moves the leds code from TPL into SPL Board init
led_setup code.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(split tpl.c change as separate patch)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add weak led_setup() so that board which has an uncommon
led setup code that can make use of custom implementation.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The new rk3288 revision rk3288w has some changes with respect
to legacy rk3288 like hclk_vio in cru and usb host0 ohci.
Linux clock driver already handle this via rockchip,rk3288w-cru
compatible.
USB ohci host can enable via dts for rk3288w based boards.
So, add fdt board setup code to update cru compatible with
rk3288w-cru compatible if the SOC revision is RK3288W.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rockchip SoC's has a new revision chip for rk3288 SoCs.
RK3288 has a new revision chip called RK3288W which is similar
but different hclk_vio clock and fixed OHCI host.
Add common Rockchip SoC detection helper to support this rk3288w
detection.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rock PI 4C has AP6256 Wifi/BT, PoE, miniDP, USB Host enabled
GPIO pin change compared to 4B, 4C.
So, add or enable difference nodes/properties in 4C dts
by including common dtsi.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rock PI 4 has 3 variants of hardware platforms called
RockPI 4A, 4B, and 4C.
- Rock PI 4A has no Wif/BT.
- Rock PI 4B has AP6256 Wifi/BT, PoE.
- Rock PI 4C has AP6256 Wifi/BT, PoE, miniDP, USB Host enable
GPIO pin change compared to 4B, 4C
So move common nodes, properties into dtsi file and include
on respective variant dts files.
Use 4B dts into default rock-pi-4 defconfig until we find any
solution for dynamic detection of these variants.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
To fix below build error:
drivers/usb/host/built-in.o: In function `xhci_dwc3_remove':
drivers/usb/host/xhci-dwc3.c:174: undefined reference to `dwc3_shutdown_phy'
drivers/usb/host/built-in.o: In function `xhci_dwc3_probe':
drivers/usb/host/xhci-dwc3.c:130: undefined reference to `dwc3_setup_phy'
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add default kernel_comp_addr_r and kernel_comp_size to support boot
from compressed kernel Image, this space is temporarily used during
decompress according to README.distro.
Reported-by: Tian Yuanhao <tianyuanhao@aliyun.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Currently 2.5 GB is calculated as DRAM size for a 1 GB RK322x board
if CONFIG_SPL_OPTEE is set. This is troublesome when booting a
linux kernel since this size will be injected in FDT of the kernel.
gd->bd->bi_dram[0].start (which is basically CONFIG_SYS_SDRAM_BASE)
must not be taken into consideration for calculation of second bank
size, since this offset is already included in calculation of "top".
After applying this patch 992 MB (1024 MB - 32 MB reserved for
optee-os) is correctly calculated and has also been verified on
2 GB boards.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Drop the legacy PHY driver and it's associated code since
the PHY handling driver now part of Generic PHY framework.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Now, we have a PCIe PHY driver as part of the Generic
PHY framework. Let's use it instead of legacy PHY driver.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the Rockchip PCIe PHY driver as part of
Generic PHY framework.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Disable ram rockchip debug driver for roc-rk3399-pc
boards since we have verified ram in many instances
with respective U-Boot versions.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The empty function define should not be in the header file, or else the
build will error with function multi definition after CONFIG_RAM_ROCKCHIP_DEBUG
is disabled.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Right now all these debug statements are printing on the
console to make sure proper dram initialization happens.
Mark them into RAM_ROCKCHIP_DEBUG would be more meaningful
and work like before since the RAM_ROCKCHIP_DEBUG is by
default yet.
No functionality changes.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
stride debug is already present in sdram_common.c via
RAM_ROCKCHIP_DEBUG.
So, drop the redundant debug stride code in rk3399 driver.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add U-Boot SPI Flash support for the PINE64 Rock64 board
Signed-off-by: Johannes Krottmayer <krjdev@gmail.com>
Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add U-Boot SPI Flash support for the PINE64 Rock64 board
Signed-off-by: Johannes Krottmayer <krjdev@gmail.com>
Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add U-Boot SPI support for the RK3328
Signed-off-by: Johannes Krottmayer <krjdev@gmail.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(fix checkpatch error for code ident)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add support for the RK3328 SPI controller
Signed-off-by: Johannes Krottmayer <krjdev@gmail.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add SPI support for the RK3328 clock driver
Signed-off-by: Johannes Krottmayer <krjdev@gmail.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Adjust the ENV offset, size to fit into all images
on 16MB flash.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable DWC3 core, gadget for roc-rk3399-pc board.
This would help to use fastboot by default.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable config options to get HDMI output on RockPI-4 boards.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable USB gadget for rock-pi-4 boards.
This would help to use fastboot by default.
Note: Connect the Host USB cable (Port A or C) to rock-pi-4
Upper USB 3.0 port.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable PCI/NVME for M.2 Slot on RockPI-4 boards.
=> nvme info
Device 0: Vendor: 0x144d Rev: 2B2QEXM7 Prod: S4EUNG0MC10012Y
Type: Hard Disk
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
Cc: Tom Cubie <tom@radxa.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable USB3.0 Host support for RockPI-4 boards.
Note that the Upper USB3.0 port is marked as otg and
lower USB3.0 port marked as host, so this below log
capture when USB3.0 mass storage plug in at lower
USB 3.0 port.
Log:
Bus usb@fe380000: USB EHCI 1.00
Bus usb@fe3c0000: USB EHCI 1.00
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe380000 for devices... 1 USB Device(s) found
scanning bus usb@fe3c0000 for devices... 1 USB Device(s) found
scanning bus dwc3 for devices... 1 USB Device(s) found
scanning bus dwc3 for devices... cannot reset port 1!?
2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
=> usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
1 Hub (5 Gb/s, 0mA)
U-Boot XHCI Host Controller
1 Hub (5 Gb/s, 0mA)
| U-Boot XHCI Host Controller
|
+-2 Mass Storage (5 Gb/s, 224mA)
SanDisk Dual Drive 040130e3ee554b7078843f4eb331646
Cc: Tom Cubie <tom@radxa.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable USB3.0 Host support for RockPro64 boards.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Also known as Odroid Go Advance but named Go2 internally by the
vendor it seems.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Get the devicetree from mainline Linux and include it for U-Boot uses.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The rk3326 is just a trimmed down px30 from a software perspective,
so the mainline rk3326 dtsi also ist just a tiny addition.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The function, pkcs7_verify_one(), will be utilized to rework signature
verification logic aiming to support intermediate certificates in
"chain of trust."
To do that, its function interface is expanded, adding an extra argument
which is expected to return the last certificate in trusted chain.
Then, this last one must further be verified with signature database, db
and/or dbx.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
This function was nullified when the file, pkcs7_verify.c, was imported
because it calls further linux-specific interfaces inside, hence that
could lead to more files being imported from linux.
We need this function in pkcs7_verify_one() and so simply re-implement it
here instead of re-using the code.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
The file, pkcs7_verify.c, will now be imported from linux code
(crypto/asymmetric_keys/pkcs7_verify.c in 5.7) and modified to fit
into U-Boot environment.
In particular, pkcs7_verify_one() function will be used in a later patch
to rework signature verification logic aiming to support intermediate
certificates in "chain of trust."
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
When the file, x509_public_key.c, was imported from linux code in
commit b4adf627d5 ("lib: crypto: add x509 parser"),
x509_check_for_self_signed() was commented out for simplicity.
Now it need be enabled in order to make pkcs7_verify_one(), which will be
imported in a later patch, functional.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
This function will be called from x509_check_for_self_signed() and
pkcs7_verify_one(), which will be imported from linux in a later patch.
While it does exist in linux code and has a similar functionality of
rsa_verify(), it calls further linux-specific interfaces inside.
That could lead to more files being imported from linux.
So simply re-implement it here instead of re-using the code.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
This is a fixup by autopep8 after the commit ("test/py: efi_secboot:
apply autopep8").
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
'tool_is_in_path' function is no longer used anywhere after Heinrich
has removed 'sudo' version of fixture setup.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Use logging instead of printf() for messages occurring when scanning block
devices during the initialization of the UEFI sub-system.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Log messages of the bootefi command instead of simply printing them to the
console.
Do not show "## Application terminated" message when the UEFI binary
completed successfully.
Adjust the python tests testing for '## Application terminated'.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Do not reset the board when returning from an UEFI FIT image.
For failed UEFI binary we already print the return status in efi_run_image.
Remove duplicate output.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When reading a directory, EFI_BUFFER_TOO_SMALL should be returned when
the supplied buffer is too small, so a use-case is to call
efi_file_read with *buffer_size=0 and buffer=NULL to obtain the needed
size before doing the actual read.
So move the buffer!=NULL check to after the buffer size has been checked.
This fix allows the Redhat shim fallback to run and e.g. Fedora 32 now
boots out of the box.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Currently we only check for the return value of tee_invoke_func().
Although OP-TEE and StMM will correctly set param[1].u.value.a and we'll
eventually return an error, the correct thing to do is check for the
OP_TEE return code as well.
So let's check for that and move tee_shm_free() and tee_close_session()
before exiting with an error to make sure we always clear the registered
memory.
Fixes: f042e47e8f ("efi_loader: Implement EFI variable handling via OP-TEE")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Use EFI_DEVICE_ERROR for TEE communication problems.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Instead of adding the definition for the specific MM SVC used in
StandAloneMM we added the one used in the standard SMC calls.
So change the value from -4 to -5 to match the correct one defined in
EDK2 and rename them to avoid future confusion
Fixes 23a397d2e2: ("efi_loader: Add headers for EDK2 StandAloneMM communication")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
efi_var_mem_del() is in __efi_runtime because it would be needed for a
runtime implementation of SetVariable(). memmove() is not in __efi_runtime.
So we should not use it in efi_var_mem_del().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Variable efi_current_var is a pointer to a physical memory address that
becomes invalid after SetVirtualAddressMap(). Instead of converting it via
ConvertPointer() simply set it to NULL.
Fixes: b02a707152 ("efi_loader: enable UEFI variables at runtime")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
