Move these fields into arch_global_data and tidy up. The bExtUart field
does not appear to be used, so punt it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move these fields into arch_global_data and tidy up. This is needed for
both ppc and m68k since they share the i2c driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move these fields into arch_global_data and tidy up.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Update for bsc9132qds.c, b4860qds.c]
Signed-off-by: Tom Rini <trini@ti.com>
Referenced arch/blackfin/lib/muldi3.c and the linux kernel.
Resolves issue seen when building u-boot for HW_MUL=0;
PLATFORM_CPPFLAGS += -mxl-soft-mul
PLATFORM_CPPFLAGS += -mno-xl-multiply-high
which resulted in error while linking to libgcc.a without mul hw (bs / m);
libgcc.a(_muldi3.o): In function `__muldi3':
.... src/gcc-4.6.2/libgcc/libgcc2.c:550: undefined reference to `_GLOBAL_OFFSET_TABLE_'
This link failure would not occur if we used gcc instead of ld directly, as
gcc will correctly use the crt's to resolve this link.
Signed-off-by: David Holsgrove <david.holsgrove@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Move vco_out, cpm_clk, scc_clk, brg_clk into arch_global_data and tidy
up. Leave pci_clk on its own since this should really depend only on
CONFIG_PCI and not any particular chip type.
Signed-off-by: Simon Glass <sjg@chromium.org>
PPC has several of these fields, selected by chip type, although only one
is ever compiled in.
Instead, use a single field. It would be nice if this could be selected
by CONFIG_PCI, but some chips (e.g. mpc5xxx) use pci_clk even when
CONFIG_PCI is not enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this field into arch_global_data and tidy up.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add arch/x86/cpu/cpu.c changes after Graeme's comments]
Signed-off-by: Tom Rini <trini@ti.com>
We currently assume that the global data pointer is at the start of
struct global_data. We want to remove this restriction, and it is
easiest to do this in C.
Remove the asm code and add equivalent code in C.
This idea was proposed by Graeme Russ here:
http://patchwork.ozlabs.org/patch/199741/
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Apply Graeme Russ' comments
http://patchwork.ozlabs.org/patch/206305/ here, re-order]
Signed-off-by: Tom Rini <trini@ti.com>
Move these fields into arch_global_data and tidy up.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Address tlb_size in this patch as well]
Signed-off-by: Tom Rini <trini@ti.com>
We plan to move architecture-specific data into a separate structure so
that we can make the rest of it common.
As a first step, create struct arch_global_data to hold these fields.
Initially it is empty.
This patch applies to all archs at once. I can split it if this is really
a pain.
Signed-off-by: Simon Glass <sjg@chromium.org>
No one expects to end up in a delayed environment if
CONFIG_DELAY_ENVIRONMENT isn't defined.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Allen Martin <amartin@nvidia.com>
The patch adds an unified linker script file which
can be used for all currently supported MIPS targets.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Xiangfu Liu <xiangfu@openmobilefree.net>
Acked-by: Stefan Roese <sr@denx.de>
The OUTPUT_FORMAT command in linker scripts
was always misused due to some endianess and
toolchain problems.
Use GCC flags to ensure proper output format,
and get rid of the OUTPUT_FORMAT commands in
the board specific u-boot.lds files.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Xiangfu Liu <xiangfu@openmobilefree.net>
The current code uses four instructions and a
temporary register to calculate the relocation
offset and to adjust the gp register.
The relocation offset can be calculated directly
from the CONFIG_SYS_MONITOR_BASE constant and from
the destination address. The resulting offset can
be used to adjust the gp pointer.
This approach makes the code a bit simpler because
it needs two instructions only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Xiangfu Liu <xiangfu@openmobilefree.net>
The difference between the address of the original
and the relocated _GLOBAL_OFFSET_TABLE_ is always
the same as the relocation offset.
The relocation offset is already computed and it is
available in the 's1/t6' register. Use that to adjust
the relocated _G_O_T_ address, instead of calculating
the offset again from the _gp value.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Xiangfu Liu <xiangfu@openmobilefree.net>
When CoreNet Fabric (CCF) internal resources are consumed by the cores,
inbound SRIO messaging traffic through RMan can put the device into a
deadlock condition.
This errata workaround forces internal resources to be reserved for
upstream transactions. This ensures resources exist on the device for
upstream transactions and removes the deadlock condition.
The Workaround is for the T4240 silicon rev 1.0.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
If property 'fsl,sec-era' is already present, it is updated.
This property is required so that applications can ascertain which
descriptor commands are supported on a particular CAAM version.
Signed-off-by: Vakul Garg <vakul@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Configuring custom memory init value using CONFIG_MEM_INIT_VALUE in
the board config file doesn't work and memory is always initialized
to the value 0xdeadbeef. Only use this default value if a board doesn't
define CONFIG_MEM_INIT_VALUE.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
e6500 implements MMUv2 and supports power-of-2 page sizes rather than
power-of-4. Add support for such pages.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The BSC9132 is a highly integrated device that targets the evolving
Microcell, Picocell, and Enterprise-Femto base station market subsegments.
The BSC9132 device combines Power Architecture e500 and DSP StarCore SC3850
core technologies with MAPLE-B2P baseband acceleration processing elements
to address the need for a high performance, low cost, integrated solution
that handles all required processing layers without the need for an
external device except for an RF transceiver or, in a Micro base station
configuration, a host device that handles the L3/L4 and handover between
sectors.
The BSC9132 SoC includes the following function and features:
- Power Architecture subsystem including two e500 processors with
512-Kbyte shared L2 cache
- Two StarCore SC3850 DSP subsystems, each with a 512-Kbyte private L2
cache
- 32 Kbyte of shared M3 memory
- The Multi Accelerator Platform Engine for Pico BaseStation Baseband
Processing (MAPLE-B2P)
- Two DDR3/3L memory interfaces with 32-bit data width (40 bits including
ECC), up to 1333 MHz data rate
- Dedicated security engine featuring trusted boot
- Two DMA controllers
- OCNDMA with four bidirectional channels
- SysDMA with sixteen bidirectional channels
- Interfaces
- Four-lane SerDes PHY
- PCI Express controller complies with the PEX Specification-Rev 2.0
- Two Common Public Radio Interface (CPRI) controller lanes
- High-speed USB 2.0 host and device controller with ULPI interface
- Enhanced secure digital (SD/MMC) host controller (eSDHC)
- Antenna interface controller (AIC), supporting four industry
standard JESD207/four custom ADI RF interfaces
- ADI lanes support both full duplex FDD support & half duplex TDD
- Universal Subscriber Identity Module (USIM) interface that
facilitates communication to SIM cards or Eurochip pre-paid phone
cards
- Two DUART, two eSPI, and two I2C controllers
- Integrated Flash memory controller (IFC)
- GPIO
- Sixteen 32-bit timers
Signed-off-by: Naveen Burmi <NaveenBurmi@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This patch adds the ability for the FSL DDR interactive debugger to
automatically run the sequence of commands stored in the ddr_interactive
environment variable. Commands are separated using ';'.
ddr_interactive=compute; edit c0 d0 dimmparms caslat_X 0x3FC0; go
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add copy command which allows copying of DIMM/controller settings.
This saves tedious retyping of parameters for each identical DIMM
or controller.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This fix allows the name of the stage to be specifed after the
controler and DIMM is specified. Prior to this fix, if the
data stage name is not the first entry on the command line,
the operation is applied to all controller and DIMMs.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Move the FSL DDR prompt command parsing to a separate function
so that it can be reused.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Using environmental variable "ddr_interactive" to activate interactive DDR
debugging seomtiems is not enough. For example, after updating SPD with a
valid but wrong image, u-boot won't come up due to wrong DDR configuration.
By enabling key press method, we can enter debug mode to have a chance to
boot without using other tools to recover the board.
CONFIG_FSL_DDR_INTERACTIVE needs to be defined in header file. To enter the
debug mode by key press, press key 'd' shortly after reset, like one would
do to abort auto booting. It is fixed to lower case 'd' at this moment.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Different personalities/derivatives of SoC may have reduced cluster. But it is
not necessary for last valid DCFG_CCSR_TP_CLUSTER register to have
DCFG_CCSR_TP_CLUSTER[EOC] bit set to represent "End of Clusters".
EOC bit can still be set in last DCFG_CCSR_TP_CLUSTER register of orignal SoC
which may not be valid for the personality.
So add initiator type check to find valid cluster.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The boot page in memory is already reserved so OS won't overwrite.
As long as the boot page translation is active, the default boot page
also needs to be reserved in case the memory is 4GB or more.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Some MXS based boards do not implement the card-detect signal. Allow
user to specify alternate card-detect implementation.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
The MX23 SSP register layout differs from MX28 in certain bits,
adjust the register layout accordingly.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
The MX23 has less channels for the APBH DMA, sligtly different register
layout and some bits in those registers are placed differently. Reflect
this in the driver. This patch fixes MMC/DMA issue on MX23.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Using the __weak annotation can make the code cleaner.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
The memory power supply on MX23 didn't pump out enough juice into
the DRAM chip, thus caused occasional memory corruption. Fix this.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Saving the parameters in advance unnecessarily complicates
the code. The destination address is already saved in the
's2' register, and that register is not clobbered by the
copy loop. The size of the copied data can be computed
after the copy loop is done.
Change the code to compute the size parameter right
before calling flush_cache, and set the destination
address parameter in the delay slot of the actuall
call.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
The current code uses four instructions and a
temporary register to calculate the relocation
offset and to adjust the gp register.
The relocation offset can be calculated directly
from the CONFIG_SYS_MONITOR_BASE constant and from
the destination address. The resulting offset can
be used to adjust the gp pointer.
This approach makes the code a bit simpler because
it needs two instructions only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Save the reused parameters at the beginning
of the 'relocate_code' function. This makes
the function a bit more readable.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
The current code uses two instructions to load
the stack pointer into the 'sp' register.
This results in the following assembly code:
468: 3c088040 lui t0,0x8040
46c: 251d0000 addiu sp,t0,0
The first instuction loads the stack pointer into
the 't0' register then the value of the 'sp' register
is computed by adding zero to the value of the 't0'
register. The same issue present on the 64-bit version
as well:
56c: 3c0c8040 lui t0,0x8040
570: 659d0000 daddiu sp,t0,0
Change the code to load the stack pointer directly
into the 'sp' register. The generated code is functionally
equivalent to the previous version but it is simpler.
32-bit:
468: 3c1d8040 lui sp,0x8040
64-bit:
56c: 3c1d8040 lui sp,0x8040
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
The loop code copies more data with one than
necessary due to the 'ble' instuction. Use the
'blt' instruction instead to fix that.
Due to the lack of suitable hardware the Xburst
specific code is compile tested only. However the
change is quite obvious.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
The romReserved and romExcHandle handlers are
accessed by a branch instruction however the
delay slots of those instructions are not filled.
Because the start.S uses the 'noreorder' directive,
the assembler will not fill the delay slots either,
and leads to the following assembly code:
0000056c <romReserved>:
56c: 1000ffff b 56c <romReserved>
00000570 <romExcHandle>:
570: 1000ffff b 570 <romExcHandle>
In the resulting code, the second branch instruction
is placed into the delay slot of the first branch
instruction, which is not allowed on the MIPS
architecture.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
The currently used 'extern inline' directive causes
the following compiler warnings if CONFIG_SWAP_IO_SPACE
is defined:
<...>/include/asm/io.h:345:1: warning: '__fswab32' is static but used in inline function '__outlc_p' which is not static [enabled by default]
<...>/include/asm/io.h:345:1: warning: '__fswab32' is static but used in inline function '__outl_p' which is not static [enabled by default]
<...>/include/asm/io.h:345:1: warning: '__fswab32' is static but used in inline function '__outlc' which is not static [enabled by default]
<...>/include/asm/io.h:345:1: warning: '__fswab32' is static but used in inline function '__outl' which is not static [enabled by default]
<...>/include/asm/io.h:344:1: warning: '__fswab16' is static but used in inline function '__outwc_p' which is not static [enabled by default]
<...>/include/asm/io.h:344:1: warning: '__fswab16' is static but used in inline function '__outw_p' which is not static [enabled by default]
<...>/include/asm/io.h:344:1: warning: '__fswab16' is static but used in inline function '__outwc' which is not static [enabled by default]
<...>/include/asm/io.h:344:1: warning: '__fswab16' is static but used in inline function '__outw' which is not static [enabled by default]
<...>/include/asm/io.h:341:1: warning: '__fswab32' is static but used in inline function '__inlc_p' which is not static [enabled by default]
<...>/include/asm/io.h:341:1: warning: '__fswab32' is static but used in inline function '__inl_p' which is not static [enabled by default]
<...>/include/asm/io.h:341:1: warning: '__fswab32' is static but used in inline function '__inlc' which is not static [enabled by default]
<...>/include/asm/io.h:341:1: warning: '__fswab32' is static but used in inline function '__inl' which is not static [enabled by default]
<...>/include/asm/io.h:340:1: warning: '__fswab16' is static but used in inline function '__inwc_p' which is not static [enabled by default]
<...>/include/asm/io.h:340:1: warning: '__fswab16' is static but used in inline function '__inw_p' which is not static [enabled by default]
<...>/include/asm/io.h:340:1: warning: '__fswab16' is static but used in inline function '__inwc' which is not static [enabled by default]
<...>/include/asm/io.h:340:1: warning: '__fswab16' is static but used in inline function '__inw' which is not static [enabled by default]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
All other IO accessor functions are using the
'inline' directive. Use that also for the __in*s
to make it consistent with the other variants.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
The '#' used as comments in the files cause the preprocessor
trouble, so change to /* */.
The mkimage command which uses this preprocessor output
was moved to arch/arm/imx-common/Makefile
.gitignore was updated to ignore .cfgtmp files.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
The MX23 has different handling of the SSP clock and GPMI NAND clock sources,
add necessary quirks into the clock code to properly handle these.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
The memory init is slightly different on MX23, thus split the memory
init for mx23 and mx28 into different functions.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
The power block on MX23 must first be ungated before it can be operated.
Add function to MXS power init that ungates it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
For i.MX23 we need to pass imx23 as elftosb param.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
This adds the boot mode support for i.MX23 processors.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add information to identify i.MX23 chips and its known revisions.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add register definitions for the i.MX23 power control block and
clock control block. These are essential for the basic bootstrap
of the i.MX23. Also, properly include them in imx-regs.h .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
This has been copied from Linux source at revision 786f02b719f.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
This adds the base addresses of i.MX23 and easy the detection of wrong
order in board setup, in case no SoC has been set, an error is raised
during build.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Create function which converts SSP bus number to SSP register pointer.
This functionality is reimplemented multiple times in the code, thus
make one common implementation. Moreover, make it a switch(), since the
SSP ports are not mapped in such nice linear fashion on MX23, therefore
having it a switch will simplify things there.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Add apbdma node for tegra20 and tegra30, copied directly from tegra
Linux dtsi files.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Sort nodes in dts files according the the following rules:
1) Any nodes that already exist in any /include/d file, in the order
they appear in the /include/d file.
2) Any nodes with a reg property, in order of their address.
3) Any nodes without a reg property, alphabetically by node name.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
IRDA is a synonym for UARTB in tegra pinmux, remove all usage of this
synonym and replace with UARTB to disambiguate.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Note that T30 does not have a separate/different DVC (power I2C)
controller like T20 - all 5 I2C controllers are identical, but
DVC_I2C is still used to designate the controller intended for
power control (PWR_I2C in the schematics). On Cardhu, it's used
to access the PMU and EEPROM, as well as the audio codec, temp
sensor, and fuel gauge devices from the OS.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add 16-bit divider support (I2C) to periph table, annotate and
correct some entries, and fix clk_id lookup function.
Signed-off-by: Tom Warren <twarren@nvidia.com>
This patch adds basic Tegra30 (T30) build support - no specific
board is targeted.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
These are stripped down for bringup, They'll be filled out later
to match-up with the kernel DT contents, and/or as devices are
brought up (mmc, usb, spi, etc.).
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
These files are used by both SPL and main U-Boot.
Also made minor changes to shared Tegra code to support
T30 differences.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
These files are for code that runs on the CPU (A9) on T30 boards.
At this time, there are no T30-specific ARMV7 files. As T30-specific
run-time code is added, it'll go here.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidai.com>
This provides SPL support for T30 boards - AVP early init, plus
CPU (A9) init/jump to main U-Boot.
Some changes were made to Tegra20 cpu.c to move common routines
into tegra-common/cpu.c and reduce code duplication.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Common Tegra files are in arch-tegra, shared between T20 and T30.
Tegra30-specific headers are in arch-tegra30. Note that some of
these will be filled in as more T30 support is added (drivers,
WB/LP0 support, etc.). A couple of Tegra20 files were changed
to support common headers in arch-tegra, also.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Boards may require a different pinmux setup for DISPALY than the default one.
Add a way to call into board specific code to set this up.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The bootm command supports subcommands since long time
however those subcommands are not yet usable on MIPS.
The patch is based on the ARM implementation, and it adds
support for the 'prep' and 'go' subcommands only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Move the environment initialization code into a
separate function. This make the code reusable
for bootm subcommands.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Move the actual jump code into a separate function.
This make the code reusable for bootm subcommands.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
The '## Transferring control ...' message is printed
only if DEBUG is enabled. Get rid of the 'ifdef DEBUG'
statement and use the debug macro instead.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
When u-boot is compiled for PXA25x processor, pxa/start.S is calling
cpu_init_crit by BL instruction. BL is overwriting lr register so
relocate_code is going into infinite loop. This patch preservs lr
register in r12 before calling cpu_init_crit and after function returns
restores it.
Signed-off-by: Lukasz Dalek <luk0104@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Fix coldfire serial driver bindings no more relocated to ram after last
changes to drivers/serial/serial.c (regression).
Serial initialization in ram has to be called after that gd->reloc_off is
calculated.
Signed-off-by: Angelo Dureghello <sysamfw@gmail.com>
Cc: Jason Jin <jason.jin@freescale.com>
Acked-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Tested-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Mobile storage is used the CLK_DIV_FSYS3 value.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
To get exactly clock value for mmc, support the get_mmc_clk() like
set_mmc_clk().
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The two modified lines were indented with spaces.
They are now indented with tabs.
Signed-off-by: Taylor Hutt <thutt@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
The timer may be inited in arch_cpu_init() so it is not safe to make a
bootstage mark before this is called. Arrange the code to fix this.
Note: The question was raised as to why we don't keep all archs in sync.
PowerPC doesn't have specific bootstage markers at present (although it
does use boot progress). I hope that the generic board series will solve
this problem in general, but in the meantime this is a real problem, and
only in ARM.
We now get a correct time for board_init_f:
Timer summary in microseconds:
Mark Elapsed Stage
0 0 reset
100,000 100,000 spl_start
848,530 748,530 board_init_f
907,301 58,771 board_init_r
910,478 3,177 board_init
Signed-off-by: Simon Glass <sjg@chromium.org>
SPL u-boot may call do_reset() which depends on interrupts.o and reset.o.
So make them also appear in SPL.
Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This option displays board info after stdio is running, so that it will
appear on the LCD. If it is displayed earlier, the board info will appear
on the serial console but not on the LCD.
Here follows a blow-by-blow description.
1a. Without CONFIG_DISPLAY_BOARDINFO_LATE, on serial:
U-Boot 2011.12-02550-g037e1c5-dirty (Nov 15 2012 - 14:29:42) for SMDK5250
CPU: S5PC520 @ 1700MHz
Board: Google Snow, rev 0
I2C: ready
DRAM: 2 GiB Elpida DDR3 @ 800MHz
MMC: S5P MSHC0: 0, S5P MSHC1: 1
SF: Detected W25Q32 with page size 4 KiB, total 4 MiB
*** Warning - bad CRC, using default environment
In: mkbp-keyb
Out: lcd
Err: lcd
Net: No ethernet found.
Hit any key to stop autoboot: 0
SMDK5250 #
1b. Without CONFIG_DISPLAY_BOARDINFO_LATE, on LCD (note machine info
is missing):
In: mkbp-keyb
Out: lcd
Err: lcd
Net: No ethernet found.
Hit any key to stop autoboot: 0
SMDK5250 #
2a. With CONFIG_DISPLAY_BOARDINFO_LATE, on serial:
U-Boot 2011.12-02550-g037e1c5 (Nov 15 2012 - 14:27:40) for SMDK5250
CPU: S5PC520 @ 1700MHz
I2C: ready
DRAM: 2 GiB Elpida DDR3 @ 800MHz
MMC: S5P MSHC0: 0, S5P MSHC1: 1
SF: Detected W25Q32 with page size 4 KiB, total 4 MiB
*** Warning - bad CRC, using default environment
Model: Google Snow
In: mkbp-keyb
Out: lcd
Err: lcd
Net: No ethernet found.
Hit any key to stop autoboot: 0
SMDK5250 #
2b. With CONFIG_DISPLAY_BOARDINFO_LATE, on LCD (note machine info is present):
Model: Google Snow
In: mkbp-keyb
Out: lcd
Err: lcd
Net: No ethernet found.
Hit any key to stop autoboot: 0
SMDK5250 #
Since the LCD is all that a typical user sees, it is useful to display
the model there.
We may be able to rearrange things some other way one day, but at
present this seems like a convenient way of getting the required
behaviour.
Signed-off-by: Simon Glass <sjg@chromium.org>
This option delays loading of the environment until later, so that only the
default environment will be available to U-Boot.
This can address the security risk of untrusted data being used during boot.
Any time you load untrusted data you expose yourself to a bug in the
code. The attacker gets to choose the data so can sometimes carefully
craft it to exploit a bug. We try to avoid touching user-controlled
data during a verified boot unless strictly necessary. Since the
default environment is good enough in this case (or you would just
change it), this gets around the problem by just not loading the
environment.
When CONFIG_DELAY_ENVIRONMENT is defined, it is convenient to have a
run-time way of enabling loading of the environment. Add this to the
fdt as /config/delay-environment.
Note: This patch depends on http://patchwork.ozlabs.org/patch/194342/
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
We want to use the fdt inside board_early_init_f(), so check for its
presence earlier in the pre-reloc init sequence.
So far ARM and microblaze are the only only ones that use
CONFIG_OF_CONTROL. Microblaze does not have the same init loop, and in
particular does not have the board_early_init_f() call. So a patch for
microblaze would have no meaning.
Signed-off-by: Simon Glass <sjg@chromium.org>
It may be necessary to know where the TLB area ends as well as where it
starts. This allows board code to complete a secure memory erase without
destroying the page tables.
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
In Cortex-A15 architecture, when we run cache invalidate
the cache clean operation executes automatically.
So if there are any dirty cache lines before disabling the L2 cache
these will be synchronized with the main memory when
invalidate_dcache_all() runs in the last part of U-boot
The two functions after flush_dcache_all is using the stack. So this
data will be on the cache. After disable when invalidate is called the
data will be flushed from cache to memory. This corrupts the stack in
invalida_dcache_all. So this change is required to avoid the u-boot
hang.
So flush has to be done just before clearing CR_C bit
Signed-off-by: Arun Mankuzhi <arun.m@samsung.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
When only DP is used, we need not enable CONFIG_EXYNOS_MIPI_DSIM.
But if we do not select CONFIG_EXYNOS_MIPI_DSIM, exynos_fb.c throws
error saying exynos_mipi_dsi_init() not defined. So, we add
dummy definition for exynos_mipi_dsi_init when CONFIG_EXYNOS_MIPI_DSIM
is not defined.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
With VPLL as source clock to FIMD,
Exynos DP Initializaton was failing sometimes with unstable clock.
Changing FIMD source to MPLL resolves this issue.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add panel_info structure required by LCD driver
and DP panel platdata for SMDK5250.
Add GPIO configuration for LCD.
Enable FIMD and DP support on SMDK5250.
DP Panel size: 2560x1600.
We use 16BPP resolution to get LCD console.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chomium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add workaround for the following ARM errata: 743622 and 751472.
The motivation for this change is the following kernel commit 62e4d357a
(ARM: 7609/1: disable errata work-arounds which access
secure registers), which removes the errata from multiplatform kernel.
Since imx has been converted to multiplatform in the kernel, we need to apply
such workarounds into the bootloader.
Workaround code has been taken from arch/arm/mm/proc-v7.S from 3.7.1 kernel.
Explanation of each erratum is provided at "Chip Errata for the i.MX 6Dual/6Quad"
document available at: cache.freescale.com/files/32bit/doc/errata/IMX6DQCE.pdf
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Modified the arch-kirkwood header so KWGBE_PORT_SERIAL_CONTROL1_REG(x)
returns the correct address.
Originally calling KWGBE_PORT_SERIAL_CONTROL1_REG(1) returned the
address for port 0 and vice versa.
Doesn't have any knock on effects to the u-boot code as the only
time they're used is to do the same function to both addresses
Signed-off-by: Luke Lowrey <luke@chamsys.co.uk>
Acked-by: Prafulla Wadaskar <Prafulla@marvell.com>
Acked-by: Heiko Schocher <hs@denx.de>
This saves stack and code memory for local copy, and
consumes initialized data memory. For 22 of the 29
kirkwood-based boards, this results in a global saving
of about 30 bytes. For 7 of them, it results in an
increase of 6 to 14 bytes.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Move all the C runtime setup code from every start.S
in arch/arm into arch/arm/lib/crt0.S. This covers
the code sequence from setting up the initial stack
to calling into board_init_r().
Also, rewrite the C runtime setup and make functions
board_init_*() and relocate_code() behave according to
normal C semantics (no jumping across the C stack any
more, etc).
Some SPL targets had to be touched because they use
start.S explicitly or for some reason; the relevant
maintainers and custodians are cc:ed.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
This patch adds the device node required for USB
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add SPI device node data for exynos.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add sound device node data for exynos
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Api is added to decode peripheral id based on the interrupt number
of the peripheral.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add I2C device node data for exynos
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch add pinmux settings for Exynos4 for mmc0 and mmc2
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Adds functions to extract clock frequency of Exynos4x12 IPs.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add device tree based ethernet driver for SMC911X controller on
SMDK5250 boards.
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds initial dts file for EXYNOS5250 SoC. This dts
file currently include only ethernet devices and properties. More
devices to be added in subsequent patches.
Also add the dts file for SMDK5250 board which uses the EXYNOS5250
dts file.
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds gpio structure for Exynos4x12.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds clock structure for Exynos4x12.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch populates base addresses of Exynos4x12 registers.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This commit merges branches from samsung, imx and tegra
meant to fix merge issues between u-boot/master and
u-boot-arm/master, as well as a few manual merge fixes.
This adds arch support for PPC mpc83xx to boot "minimal" (4K) SPLs
using the new infrastructure.
Existing nand_spl targets are updated to deal with the name change
from nand_init.c to spl_minimal.c (as in theory this isn't limited
to NAND anymore).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Move the getenv_yesno() to env_common.c and change most checks for
'y' or 'n' to use this helper.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
