This target is out of maintenance and can be removed.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
CC: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
This board is similar to SUV31, but the FPGA is reset concept is quite
different.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
CC: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
KMSUGP1 is from a u-boot perspective (almost) identical to KMNUSA.
The only difference is that the PCIe reset is connected to Kirkwood pin
MPP7_PEX_RST_OUTn, we use a dedicated config flag KM_PCIE_RESET_MPP7.
Such pin should theoretically be handled by the PCIe subsystem
automatically, but this turned out not to be the case.
So simply configure this PIN as a GPIO and issue a pulse manually.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Karlheinz Jerg <karlheinz.jerg@keymile.com>
Cc: Valentin Longchamp <valenting.longchamp@keymile.com>
Cc: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
The PCIe FPGAs now have to support 2 resets: one for the non traffic
affecting part (PCIe) and one for the traffic affecting part.
When the FPGA is not reconfigured, we only reset the PCIe part.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
In order to be able to perform board resets without interrupting the
traffic, the configuration of an already properly configured FPGA is
skipped.
This is because some PCIe FPGAs embed some other function that must
continue to work over reset.
It is then the responsibility of the application to trigger a
reconfiguration when needed. This is done by lowering the FPGA_INIT_B
pin for delaying the configuration to u-boot @ next reboot, and then
lower the FPGA_PROGRAM_B signal.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
This adds a first support of the FPGA download for a PCIe FPGA based
on the BOCO2 CPLD.
This takes place in 3 steps, all done accessing the SPICTRL reg of the
BOCO2:
1) start the FPGA config with an access to the FPGA_PROG bit
2) later in the boot sequence, wait for the FPGA_DONE bit to toggle to 1
for the end of the FPGA configuration (with a timeout)
3) reset the FPGA
4) finally remove the access to its config EEPROM from the FPGA so that
the CPU can update the FPGA configuration when the kernel is running
The boards with a PCIe FPGA but without BOCO2 still are supported.
The config option name is CONFIG_KM_FPGA_CONFIG
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
