Commit graph

74737 commits

Author SHA1 Message Date
Tim Harvey
aea162c10e arm: dts: imx8mm-venice-gw700x: fix fifo-depth phy props
Replace the deprecated 'tx-fifo-depth' and 'rx-fifo-depth' properties
not supported by U-Boot drivers/net/phy/dp83867.c with the proper
'ti,fifo-depth' property.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-08-09 14:46:50 +02:00
Tim Harvey
98559e02f1 arm: dts: imx8mm-venice-gw71xx: fix USB OTG VBUS
The GW71xx has a USB Type-C connector with USB 2.0 signaling. GPIO1_12
is the power-enable to the TPS25821 Source controller and power switch
responsible for monitoring the CC pins and enabling VBUS. Therefore
GPIO1_12 must always be enabled and the vbus output enable from the
IMX8MM can be ignored.

To fix USB OTG VBUS enable a pull-up on GPIO1_12 to always power the
TPS25821 and change the regulator output to GPIO1_10 which is
unconnected.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-08-09 14:46:50 +02:00
Fabio Estevam
82679f94e7 warp: Use the correct symbol for CONFIG_IMX_HAB
The intention of commit d714a75fd4 ("imx: replace CONFIG_SECURE_BOOT
with CONFIG_IMX_HAB") was to convert from CONFIG_SECURE_BOOT to
CONFIG_IMX_HAB, but it replaced with an extra "_" character.

Fix it by using the correct CONFIG_IMX_HAB symbol.

Fixes: d714a75fd4 ("imx: replace CONFIG_SECURE_BOOT with CONFIG_IMX_HAB")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
2021-08-09 14:46:50 +02:00
Tim Harvey
249ee657e6 imx: ventana: add support for GW54xx-G revision
The GW54xx-G revision has the foolowing changes:
 - replaces the EOL GbE PHY with an updated part (requires an enable pin)
 - replaces the EOL analog video decoder with an updated part
   (requires dt prop)
 - add power control to miniPCIe socket

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-08-09 14:46:50 +02:00
Tim Harvey
bf6bdefd36 imx: ventana: add support for GW53xx-G revision
The GW53xx-G revision has the foolowing changes:
 - replaces the EOL GbE PHY with an updated part (requires an enable pin)
 - replaces the EOL analog video decoder with an updated part
   (requires dt prop)
 - add power control to miniPCIe socket

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-08-09 14:46:50 +02:00
Tim Harvey
3ef59acdaf imx: ventana: add GW5913 support
The GW5913 is a Single Board Computer based on the NXP i.MX6Q/DL SoC
with the following features:
 - DDR3 DRAM
 - NAND FLASH (256MiB or 2048MiB)
 - Gateworks System Periperhal Controller
 - front panel LED's
 - front panel pushbutton
 - Digital I/O connector (I2C/GPIO/UART)
 - u-blox Zoe-M8Q GPS
 - 1x RJ45 GbE
 - 1x MiniPCIe socket with PCIe USB 2.0 and nanoSIM socket
 - Passive PoE and wide-range DC power supply

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-08-09 14:46:50 +02:00
Tim Harvey
744d21c126 imx: ventana: add GW5912 support
The GW5912 is a Single Board Computer based on the NXP i.MX6Q/DL SoC
with the following features:
 - DDR3 DRAM
 - NAND FLASH (256MiB or 2048MiB)
 - microSD socket
 - Gateworks System Periperhal Controller
 - front panel LED's
 - front panel pushbutton
 - RS232 connector (2x UARTs)
 - CAN/RS485 connector
 - Digital I/O connector (I2C/GPIO)
 - SPI connector
 - u-blox Zoe-M8Q GPS
 - LIS2DE12 Accellerometer
 - 1x FEC GbE RJ45 with 802.3at Active PoE
 - 1x PCI GbE RJ45 with Passive PoE
 - 5x MiniPCIe socket with PCIe/USB 2.0
 - 1x MiniPCIe socket with PCIe/USB 2.0 and SIM socket
 - Aux power input with wide-range DC power supply

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-08-09 14:46:50 +02:00
Tim Harvey
25805401ff imx: ventana: add GW5910 support
The GW5910 is a Single Board Computer based on the NXP i.MX6Q/DL SoC
with the following features:
 - DDR3 DRAM
 - NAND FLASH (256MiB or 2048MiB)
 - microSD socket
 - Gateworks System Periperhal Controller
 - front panel LED's
 - front panel pushbutton
 - RS232 connector (2x UARTs)
 - Digital I/O connector (I2C/GPIO)
 - SPI connector
 - u-blox Zoe-M8Q GPS
 - LIS2DE12 Accellerometer
 - TI CC1352 ARM Cortex-M4 multiprotocol sub-1GHz / 2.4GHz wireless MCU
 - On-board brcmfmac WiFi and BT module
 - RGMII RJ45 GbE
 - 1x MiniPCIe socket with PCIe/USB 2.0
 - 1x MiniPCIe socket with USB 2.0 and nanoSIM socket
 - Passive PoE and wide-range DC power supply

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-08-09 14:46:50 +02:00
Tim Harvey
2d02586028 imx: ventana: use dt for hwmon
Use dt-bindings for GSC hwmon devices.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-08-09 14:46:50 +02:00
Tim Harvey
49b4efe621 imx: ventana: remove hard-coded flexcan standby pin
Flexcan pinmux is configured in kernel dt.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-08-09 14:46:50 +02:00
Tim Harvey
395f17d0ea imx: ventana: remove hard-coded analog video codec enable
Analog video codec enable is configured in kernel dt.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-08-09 14:46:50 +02:00
Tim Harvey
a194e6ed45 imx: ventana: remove hard-coded USB OTG pinmux
pinmux is now done via dt. Add missing OTG_OC pinmux for boards that
use it.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-08-09 14:46:50 +02:00
Tim Harvey
aa85d251db imx: ventana: remove hard-coded PCI reset
PCIe reset configuration is handled via dt now.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-08-09 14:46:50 +02:00
Tim Harvey
dd79c97b92 imx: ventana: fix UMS support
The Gateworks Ventana boards have always had usb0=usbh1 and usb1=usbotg
because OTG is often subloaded on these boards and a bit in the EEPROM
which flagging that OTG is subloaded is used to remove the dt node via the
alias.

U-Boot DM_USB UMS requires the usb0 alias be assigned to the usbotg
so fix the usb0 alias in order for UMS to work.

Fixes 72c46327f0: ("imx: ventana: enable dm support for USB")

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-08-09 14:46:50 +02:00
Tim Harvey
034105a8f7 imx: ventana: remove hard-coded USB HUBRST# gpio config
The USB HUB reset is handled via dt now.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-08-09 14:46:50 +02:00
Tim Harvey
92309aacda imx: ventana: replace hard-coded LED config with dt based config
Use device-tree LED config instead of hard-coded board-specific config.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-08-09 14:46:50 +02:00
Tim Harvey
706d910bbc imx: ventana: remove nand field from common ventana struct
NAND fdt fixups can be performed without knowing if NAND is present.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-08-09 14:46:50 +02:00
Tim Harvey
45c902c434 imx: ventana: move wdog/uhs-i board/revision dt fixups
Move board/revision specific dt fixups for WDOG and UHS-I features
so that we can call them early for U-Boot control dt as well.

Additionally drop a deprected non-mainline dt-prop fixup regarding
HDMI input format.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-08-09 14:46:50 +02:00
Tim Harvey
36de64f2eb imx: ventana: ignore EEPROM config when checking for NAND support
EEPROM bits no longer indicate support for NAND so instead use
hard-coded value from board config struct.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-08-09 14:46:50 +02:00
Oleksandr Suvorov
d9275ebbff board: colibri_vf: fix compiling warning
This patch fixes the following compiler warning:
=============
board/toradex/colibri_vf/colibri_vf.c: In function 'ft_board_setup':
board/toradex/colibri_vf/colibri_vf.c:436:6: warning: unused variable 'ret' [-Wunused-variable]
=============

Fixes: be3f1a56bf ("video: fsl_dcu_fb: add DM_VIDEO support")
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2021-08-09 13:09:29 +02:00
Ming Liu
87421ab644 board: colibri_imx6: add board_fit_config_name_match to support FIT in SPL
Only one dtb is currently supported, so match with imx6-colibri.

Signed-off-by: Ming Liu <ming.liu@toradex.com>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2021-08-09 13:09:29 +02:00
Oleksandr Suvorov
6150295061 board: colibri-imx8x: update building documentation
Update the documentation on how to build the u-boot image for
Colibri iMX8QXP, adding support of V1.0D revision of the module.

Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2021-08-09 13:09:29 +02:00
Stefan Agner
421440f70d board: toradex: make USB PID from config block optional
If config block support is enabled, USB gadget modes unconditionally
use Toradex Product ID as USB PID. Some applications might prefer a
different and/or static USB PID. Add a Kconfig configuration option
to descide whether to use USB PID from config block or the fallback
config option CONFIG_G_DNL_PRODUCT_NUM.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2021-08-09 13:09:29 +02:00
Stefan Agner
46307ef01e board: colibri_imx7: use SDP if USB serial downloader has been used
In case USB serial downloader has been used to load U-Boot start the
serial download protocol (SDP) emulation. This allows to download
complete images such as Toradex Easy Installer over USB SDP as well.
This code uses the boot ROM provided boot information to reliably
detect USB serial downloader.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2021-08-09 13:09:29 +02:00
Fabio Estevam
5d236df9a0 mx6cuboxi: Fix the console variable
Do not pass the console baudrate to the 'console' variable
to avoid the baudrate being passed twice when extlinux.conf
contains the standard: console=${console},${baudrate} format.

cat /proc/cmdline
root=PARTUUID=00000000-01 rootwait rw console=ttymxc0,115200,115200

Signed-off-by: Fabio Estevam <festevam@gmail.com>
2021-08-09 13:09:29 +02:00
Fabio Estevam
22e9e0dc17 mx6cuboxi: Fix the mmc device for the rootfs
After the conversion to DM_MMC, the rootfs becomes mmc 1, so
adjust it accordingly.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
2021-08-09 13:09:29 +02:00
Simon Glass
e679f39f7f dtoc: Correct the intarray-widening test case
This case was intended to check that widening an int array with an int
does nothing. Fix it.

Reported-by: Walter Lozano <walter.lozano@collabora.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Walter Lozano <walter.lozano@collabora.com>
2021-08-08 11:27:27 -06:00
Simon Glass
5974718752 patman: Avoid blank lines between tags
In some cases 'patman status' leaves a blank line between the sign-off
and the tags it collects from patchwork. Fix this and add a test.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-08-08 11:27:27 -06:00
Simon Glass
1e9ced28f1 dm: core: Don't allow uclass use before ready
At present it is possible to call uclass_get() before driver model is
inited. In fact this happens on x86 boards which use Intel FSPv1, since
mrccache_get_region() tries to get the SPI flash device very early
during init.

This has always been undefined behaviour. Previously it generally worked,
i.e. returned an error code without crashing, because gd->uclass_root_s
is zeroed and the uclass can be added despite driver model not being
ready, due to the way lists are implemented. With the change to use a
gd->uclass_root pointer, this no-longer works. For example, it causes a
hang on minnowmax.

Fix this by adding a check that driver model is ready when uclass_get() is
called. This function is called in the process of locating any device, so
it is a good place to add the check.

This fixes booting on minnowmax.

Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 8a715530bb ("dm: core: Allow the uclass list to move")
2021-08-08 11:27:27 -06:00
Patrick Delaunay
b18b38f2ae dm: migrate the dm_warn to use the log macro
Migrate the dm_warn function to log macro with
LOGC_DM category and LOGL_WARNING level.

This macro allows filtering with log command and allows
output on all log backend.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2021-08-08 11:27:27 -06:00
Jan Kiszka
3823315cbe Revert "arm: bootm: Disable LMB reservation for command line and board info on arm64"
This reverts commit 2359fa7a87.

While the goal is valid and there is surely unused memory in that area,
we also have a lot of crucial things still located at the top-of-memory
while running lmb_alloc_base. Such things are the page table (tlb_addr),
relocated U-Boot and the active stack. Possibly more. So this patch was
premature, we will need relocations of those things first if we want to
use the range.

Fixes booting on the IOT2050, but likely also on other boards. It got
stuck on relocating the FDT - over the relocated U-Boot code.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
2021-08-08 11:59:01 -04:00
Tom Rini
b721d0545f Merge https://source.denx.de/u-boot/custodians/u-boot-sh 2021-08-08 09:08:22 -04:00
Marek Vasut
0ae06f6b36 ARM: renesas: Set CONFIG_SYS_TEXT_BASE=0x0 on R-Car Gen3
Since R-Car Gen3 already enables position independent build, also set
CONFIG_SYS_TEXT_BASE=0x0 to finalize the switch. This is possible since
534f0fbd65 ("arm64: Fix relocation of env_addr if POSITION_INDEPENDENT=y")
fixed current env_get_char() crash with CONFIG_SYS_TEXT_BASE=0x0 .

This change permits us to start U-Boot from any location in DRAM instead
of specific TEXT_BASE.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
2021-08-08 12:27:04 +02:00
Marek Vasut
d2d9ecb88e ARM: renesas: Mallocate bootparams on Gen3
The bootparams do not have to be at fixed location, they can be
dynamically mallocated instead. Make it so to get rid of another
fixed assignment.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Biju Das <biju.das.jz@bp.renesas.com>
Cc: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
2021-08-08 12:27:04 +02:00
Marek Vasut
2525fa3cb8 ARM: renesas: Turn on PIE for Gen3
Turn on PIE, so that the U-Boot binary can be started from any arbitrary
location in DRAM instead of a predefined fixed one. Note that this patch
is not setting SYS_TEXT_BASE=0x0 yet, since that triggers relocation bugs
in env code that are yet to be fixed.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Biju Das <biju.das.jz@bp.renesas.com>
Cc: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
2021-08-08 12:27:04 +02:00
Marek Vasut
cc68d3fcce ARM: rmobile: Remove default bootargs
The bootargs in all those boards are a copy of initial example
bootargs, just remove those as they make little sense in most
configurations.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
2021-08-08 12:27:04 +02:00
Tom Rini
8f07f5376a - add display driver for ST-Ericsson MCDE
- drop legacy CONFIG_VIDEO dependency for Hitachi tx18d42vm
 -----BEGIN PGP SIGNATURE-----
 
 iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCYQxSug4cYWd1c3RAZGVu
 eC5kZQAKCRBM6ATMmsalXEcdAJ4yWCMX2fxbY8qTFR5ovC7lKFTi9QCdHr+BM+jS
 2//ErMcUxdSPKbrwZ5E=
 =O0cV
 -----END PGP SIGNATURE-----

Merge tag 'video-2021-08-05' of https://source.denx.de/u-boot/custodians/u-boot-video

 - add display driver for ST-Ericsson MCDE
 - drop legacy CONFIG_VIDEO dependency for Hitachi tx18d42vm
2021-08-06 13:46:40 -04:00
Tom Rini
abc7841854 Merge branch '2021-08-05-drop-almost-all-pre-dm_pci-code'
- Remove the majority of our pre-DM_PCI PCI code as DM_PCI is true in
  almost all cases now.
2021-08-06 13:45:57 -04:00
Simon Glass
83042fd64d pci: Drop migration method
Migration is complete. Drop the message.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-08-06 08:26:48 -04:00
Simon Glass
4a753fbcee ppc: Drop t4qds and b4860qds references
These boards have been removed. Drop the config file and other references.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-08-06 08:26:48 -04:00
Simon Glass
666671ecc3 ppc: Drop idt8t49n222a_serdes_clk driver
This is not used. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-08-06 08:26:48 -04:00
Simon Glass
22137b8d73 pci: ppc: Drop ftpci100 driver
This is not used in U-Boot at present. Drop it and related config options.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-08-06 08:26:48 -04:00
Simon Glass
23cd8a63a0 pci: Drop pci_init_board()
With the conversion to driver model, this is not needed now. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-08-06 08:26:48 -04:00
Simon Glass
e15ba68029 distro_bootcmd: Update DM_PCI check
Now that driver model is always used, check for PCI.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Update logic, reword]
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-06 08:26:09 -04:00
Simon Glass
6b4a2a5c86 pci: sata_sil: Drop DM_PCI checks
We don't need these checks anymore since when PCI is enabled, driver model
is always used.

Drop them.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-08-06 08:21:03 -04:00
Simon Glass
ebacc78e3e pci: arm: mvebu: Drop DM_PCI check from arch_early_init_r
We don't need this check anymore since when PCI is enabled, driver model
is always used.

Use CONFIG_PCI instead.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Correct macro usage)
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-06 08:20:45 -04:00
Fabio Estevam
3f24bd329b imx28-evk: Import devicetree file from Linux
Import the imx28-evk devicetree files from Linux kernel
version 5.11-rc7.

This is in preparation for converting the mx28evk_defconfig
target to driver model.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
2021-08-06 13:26:08 +02:00
Simon Glass
63814a6986 pci: imx: Drop DM_PCI check from cpu driver
We don't need this check anymore since when PCI is enabled, driver model
is always used.

Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-08-05 19:46:35 -04:00
Simon Glass
199056d1a1 pci: Drop DM_PCI check from bios_emul
We don't need these checks anymore since when PCI is enabled, driver model
is always used.

Drop them.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-08-05 19:46:35 -04:00
Simon Glass
eb4b7fa0ae pci: scsi: pci: Drop DM_PCI check from scsi
We don't need this check anymore since when PCI is enabled, driver model
is always used.

Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-08-05 19:46:35 -04:00