Commit graph

351 commits

Author SHA1 Message Date
Stefan Roese
71665ebf88 ppc4xx: Add Canyonlands NAND booting support
460EX doesn't support a fixed bootstrap option to boot from 512 byte page
NAND devices. The only bootstrap option for NAND booting is option F for
2k page devices. So to boot from a 512 bype page device, the I2C bootstrap
EEPROM needs to be programmed accordingly.

This patch adds basic NAND booting support for the AMCC Canyonlands aval
board and also adds support to the "bootstrap" command, to enable NAND
booting I2C setting.

Tested with 512 byte page NAND device (32MByte) on Canyonlands.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-15 07:28:05 +01:00
Stefan Roese
2801b2d2a9 ppc4xx: Add basic support for AMCC 460EX/460GT (2/5)
This patch adds basic support for the AMCC 460EX/460GT PPC's.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-15 07:28:04 +01:00
Stefan Roese
8ac41e3e37 ppc4xx: Add basic support for AMCC 460EX/460GT (1/5)
This patch adds basic support for the AMCC 460EX/460GT PPC's.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-15 07:28:03 +01:00
Stefan Roese
56e4101783 ppc4xx: interrupt.c reworked
This patch is a rework of the 4xx interrupt handling done while
adding the 460EX/GT support. Interrupts are needed on 4xx for the
EMAC driver.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-15 07:28:03 +01:00
Stefan Roese
84a999b6cd ppc4xx: program_tlb now uses 64bit physical addess
This patch changes the physical addess parameter from 32bit to 64bit.
This is needed for 36bit 4xx platforms to access areas located
beyond the 4GB border, like SoC peripherals (EBC etc.).

Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-15 07:28:03 +01:00
Stefan Roese
c3307fa186 ppc4xx: miiphy.c reworked
While adding the 460EX/GT support I reworked the 4xx miiphy code. It
badly neede some cleanup.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-15 07:28:03 +01:00
Mike Nuss
74eb022259 PPC4xx (Sequoia): Fix Ethernet "remote fault" problems
Every now and then a Sequoia board (or equivalent hardware) had
problems connecting to a Gigabit capable network interface.

There were differences in the PHY setup between Linux and U-Boot.

This patch fixes the problem. Apparently "remote fault" is being set,
which signals to some devices (on the other end of the cable) that a
fault has occurred, while other devices ignore it. I believe the RF bit
was causing the issue, but I removed T4 also, to match up with Linux.

Signed-off-by: Mike Nuss <mike@terascala.com>
2008-03-04 08:55:27 +01:00
Stefan Roese
76957cb3d6 ppc4xx: EMAC: Fix 405EZ fifo size setup in EMAC_MR1
The 405EZ only supports 512 bytes of rx-/tx-fifo EMAC sizes. But
currently 4k/2k is configured. This patch fixes this issue.

Thanks to Thomas Kindler <tkindler@lenord.de> for pointing this out.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-02 22:49:27 +01:00
Anatolij Gustschin
4fae35a53b ppc4xx: Fix problem in 4xx_enet.c driver
U-Boot crashes in the net loop if CONFIG_4xx_DCACHE is
enabled. To reproduce the problem ensure that 'ethrotate'
environment variable isn't set to "no" and then run
"tftp 200000 not_existent_file".
This patch tries to fix the issue.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2008-03-02 21:34:55 +01:00
Shinya Kuribayashi
495a0dde7f cpu/ppc4xx/config.mk: Make a needlessly deffered expansion immediate.
This will reduce the build time.

Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
2008-02-23 09:44:54 +01:00
Wolfgang Denk
32c70d3420 Merge branch 'master' of git://www.denx.de/git/u-boot-ppc4xx 2008-02-15 00:22:37 +01:00
Wolfgang Denk
e7670f6c1e PPC: Use r2 instead of r29 as global data pointer
R29 was an unlucky choice as with recent toolchains (gcc-4.2.x) gcc
will refuse to use load/store multiple insns; instead, it issues a
list of simple load/store instructions upon function entry and exit,
resulting in bigger code size, which in turn makes the build for a
few boards fail.

Use r2 instead.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-02-14 22:43:22 +01:00
Rafal Jaworowski
f57d7d364c ppc: Refactor cache routines, so there is only one common set.
Signed-off-by: Rafal Jaworowski <raj@semihalf.com>
2008-02-14 22:00:41 +01:00
Larry Johnson
29e3500cbc ppc4xx: Add CONFIG_4xx_DCACHE compile switch to Denali-core SPD code
Signed-off-by: Larry Johnson <lrj@acm.org>
2008-02-14 07:42:32 +01:00
Stefan Roese
ff02f13980 ppc4xx: Fix ndfc HW ECC byte order
The current ndfc HW ECC implementation swaps the first two ECC bytes.
But the 4xx NDFC already uses the SMC (Smart Media Card) ECC ordering,
so this swapping in the HW ECC driver is bogus. This patch fixes this
problem and now really uses the SMC ECC byte order.

Thanks to Sean MacLennan for pointing this out.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-02-04 11:47:40 +01:00
Stefan Roese
28d77d968b ppc4xx: Fix problem with init-ram bigger than 4k on 440 platforms
Signed-off-by: Stefan Roese <sr@denx.de>
2008-02-04 11:47:40 +01:00
Stefan Roese
9adfc9fb9a ppc4xx: Remove compiler warning in cpu/ppc4xx/44x_spd_ddr2.c
Signed-off-by: Stefan Roese <sr@denx.de>
2008-01-15 10:11:02 +01:00
Larry Johnson
6d8184b00c ppc4xx: Fix dflush() to restore DVLIM register
Signed-off-by: Larry Johnson <lrj@acm.org>
2008-01-10 18:53:16 +01:00
Marcel Ziswiler
7817cb2083 fix comments with new drivers organization
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
2008-01-09 21:48:49 +01:00
Stefan Roese
1466ef8db5 Merge branch 'lwmon5-no-ocm' 2008-01-09 10:43:47 +01:00
Stefan Roese
1754f50b71 ppc4xx: Add CFG_POST_ALT_WORD_ADDR to support non OCM POST WORD storage
The privious 4xx POST implementation only supported storing the POST
WORD in OCM. Since we need to reserve the OCM on LWMON5 for the logbuffer
we need to store the POST WORD in some other non volatile location.
This patch adds CFG_POST_ALT_WORD_ADDR to specify an address for such
a location.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-01-09 10:25:46 +01:00
Stefan Roese
e02c521d94 ppc4xx: Add 44x cache locking to better support init-ram in d-cache
This patch adds support for locking the init-ram/stack in d-cache,
so that other regions may use d-cache as well

Note, that this current implementation locks exactly 4k of d-cache,
so please make sure that you don't define a bigger init-ram area. Take
a look at the lwmon5 440EPx implementation as a reference.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-01-09 10:23:16 +01:00
Matthias Fuchs
6e9233d30a ppc4xx: Move cpu/ppc4xx/vecnum.h into include path
This patch allows the use of 4xx interrupt vector number defines
in board specific code outside cpu/ppc4xx.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
2008-01-09 06:32:58 +01:00
Matthias Fuchs
580d1d3186 ppc4xx: Fix UIC2 vector number base
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
2008-01-09 06:32:54 +01:00
Stefan Roese
802b769bac ppc4xx: Return 0 on success in 4xx ethernet driver
Signed-off-by: Stefan Roese <sr@denx.de>
2008-01-08 18:39:30 +01:00
Larry Johnson
e05329516a ppc4xx: Remove weak binding from common Denali data-eye search code
Now that there are no board-specific versions of
"denali_core_search_data_eye()", the weak binding on the common version
can be removed.

Signed-off-by: Larry Johnson <lrj@acm.org>
2008-01-05 10:14:56 +01:00
Stefan Roese
6399b23d60 Merge branch 'katmai-ddr-gda' 2008-01-05 10:13:40 +01:00
Stefan Roese
5ba576c016 ppc4xx: Remove unused CONFIG_ECC_ERROR_RESET from 44x_spd_ddr2.c
Signed-off-by: Stefan Roese <sr@denx.de>
2008-01-05 09:13:46 +01:00
Stefan Roese
845c6c95db ppc4xx: Update Katmai/44x_spd_ddr2.c code for optimal DDR2 setup
On Katmai the complete auto-calibration somehow doesn't seem to
produce the best results, meaning optimal values for RQFD/RFFD.
This was discovered by GDA using a high bandwidth scope,
analyzing the DDR2 signals. GDA provided a fixed value for RQFD,
so now on Katmai "only" RFFD is auto-calibrated.

This patch also adds RDCC calibration as mentioned on page 7 of
the AMCC PowerPC440SP/SPe DDR2 application note:
"DDR1/DDR2 Initialization Sequence and Dynamic Tuning"

Signed-off-by: Stefan Roese <sr@denx.de>
2008-01-05 09:12:41 +01:00
Lawrence R. Johnson
5ab884b254 ppc4xx: Add functionality to GPIO support
This patch makes two additions to GPIO support:

First, it adds function gpio_read_in_bit() to read the a bit from the
GPIO Input Register (GPIOx_IR) in the same way that function
gpio_read_out_bit() reads a bit from the GPIO Output Register
(GPIOx_OR).

Second, it modifies function gpio_set_chip_configuration() to provide
an additional option for configuring the GPIO from the
"CFG_4xx_GPIO_TABLE".

According to the 440EPx User's Manual, when an alternate output is used,
the three-state control is configured in one of two ways, depending on
the particular output.  The first option is to select the corresponding
alternate three-state control in the GPIOx_TRSH/L registers.  The second
option is to select the GPIO Three-State Control Register (GPIOx_TCR) in
the GPIOx_TRSH/L registers, and set the corresponding bit in the
GPIOx_TCR register to enable the output.  For example, the Manual
specifies configuring the GPIO00 Alternate 1 Signal (PreAddr07) to use
the alternate three-state control (first option), and specifies
configuring the GPIO32 Alternate 1 Signal (USB2OM0) with the output
enabled in the GPIOx_TCR register (second option).

Currently, gpio_set_chip_configuration() configures all alternate signal
outputs to use the first option.  This patch allow the second option to
be selected by setting the "out_val" element in the table entry to
"GPIO_OUT_1".  The first option is used when the "out_val" element is
set to "GPIO_OUT_0".  Because "out_val" is not currently used when an
alternate signal is selected, and because all current GPIO tables set
"out_val" to "GPIO_OUT_0" for all alternate signals, this patch should
not change any existing configurations.

Signed-off-by: Larry Johnson <lrj@acm.org>
2008-01-04 11:38:45 +01:00
Stefan Roese
c05569066d ppc4xx: Enable 405EP PCI arbiter per default on all boards
In an attmemt to clean up the 4xx start.S file, I removed the enabling
of the internal 405EP PCI arbiter. This is needed for multiple other
405EP platforms, like most of the esd 405EP. Now the internal PCI
arbiter is enabled again per default as it has been before.

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
2007-12-28 16:39:15 +01:00
Stefan Roese
bec9264616 ppc4xx: Fix bug in cpu_init.c (405EP instead of 450EP)
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
2007-12-28 16:39:11 +01:00
Larry Johnson
8eb52d5d98 Add denali_data_eye.o and denali_spd_ddr2.o to PPC4xx Makefile
Signed-off-by: Larry Johnson <lrj@acm.org>
2007-12-27 19:35:36 +01:00
Larry Johnson
aba19604d8 Add 440EPx DDR2 SPD DIMM support
This patch adds SPD DDR2 support for the 440EPx ("Denali") SDRAM
controller.  It should also work on the 440GRx.  It is based on the DDR2
SPD code for the 440EP/440EPx, but makes no provision for DDR1 support.

This code has been tested on prototype Korat boards with three Kingston
DIMMS: 512 MiB ECC (one rank), 512 MiB non-ECC (one rank) and 1 GiB ECC
(two ranks).  The Korat board has a single DIMM socket, but support has
been provided (though not tested) for boards with two DIMM sockets.

Signed-off-by: Larry Johnson <lrj@acm.org>
2007-12-27 19:35:36 +01:00
Larry Johnson
8a24a69630 Copy 440EPx/GRx SDRAM data-eye search to common directory
This patch creates a non-board-specific file for performing the SDRAM
data-eye search.  It also adds ECC error checking to the test of valid
data on readback when ECC is enabled.

Signed-off-by: Larry Johnson <lrj@acm.org>
2007-12-27 19:35:36 +01:00
Larry Johnson
c348578bf6 Add Ethernet 1000BASE-X support for PPC4xx
This patch adds a new switch: "CONFIG_PHY_DYNAMIC_ANEG".  When this symbol
is defined, the PHY will advertise it's capabilities for autonegotiation
based on the capabilities shown in the PHY's status registers, including
1000BASE-X.  When "CONFIG_PHY_DYNAMIC_ANEG" is not defined, the PHY will
advertise hard-coded capabilities, as before.

Signed-off-by: Larry Johnson <lrj@acm.org>
2007-12-27 19:35:36 +01:00
Stefan Roese
328a340392 ppc4xx: fdt: Cleanup setup of cpu node setup
Now the cpu node setup ("timebase-frequency" and "clock-frequency") is
without using the absolute path to the cpu node. This makes it possible
to use this U-Boot version with both versions of cpu-node naming
"cpu@0" and the former "PowerPC,440EPx@0".

Signed-off-by: Stefan Roese <sr@denx.de>
2007-12-27 19:35:34 +01:00
Anatolij Gustschin
42ed33ffe1 Fix ppc4xx clear_bss() code
ppc4xx clear_bss() fails if BSS segment size is not
divisible by 4 without remainder. This patch provides
fix for this problem.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2007-12-27 19:35:34 +01:00
Niklaus Giger
85dc2a7f82 PPC4xx: Minimal changes to add vxWorks support
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
2007-12-27 19:35:34 +01:00
Matthias Fuchs
ba79fde58a ppc4xx: fix flush + invalidate_dcache_range arguments
flush + invalidate_dcache_range() expect the start and stop+1 address.
So the stop address is the first address behind (!) the range.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
2007-12-27 19:35:33 +01:00
Stefan Roese
871e6ce188 ppc4xx: fdt: use fdt_fixup_ethernet()
By using aliases in the dts file, the ethernet node fixup is
much easier with the recently added functions.

Please note that the dts file needs the aliases for this to work.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-12-27 19:35:33 +01:00
Stefan Roese
136288847e ppc4xx: Bring 4xx fdt support up-to-date
This patch update the 4xx fdt support. It enabled fdt booting
on the AMCC Kilauea and Sequoia for now. More can follow later
quite easily.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-12-27 19:35:32 +01:00
Stefan Roese
3b9abdc448 ppc4xx: Correct GPIO offset in gpio_config()
Thanks to Gary Jennejohn for pointing this out.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-12-11 13:38:19 +01:00
Stefan Roese
653811a3c2 ppc4xx: Correct 405EX PCIe UTL register mapping
Map 4k mem space for UTL registers for each port.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-18 14:44:44 +01:00
Stefan Roese
f31d38b9ee ppc4xx: Enable 405EX PCIe UTL register configuration
Till now the UTL registers on 405EX were not initialized but left with
their default values. This patch new initializes some of the UTL
registers on 405EX.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-16 14:16:54 +01:00
Stefan Roese
aee747f19b ppc4xx: Enable 440 GPIO init table CFG_440_GPIO_TABLE for 405 platforms
- Rename CFG_440_GPIO_TABLE to CFG_4xx_GPIO_TABLE
- Cleanup of the 4xx GPIO functions
- Move some GPIO defines from the cpu headers ppc405.h/ppc440.h into gpio.h

Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-15 14:23:55 +01:00
Stefan Roese
7d0a4066b5 ppc4xx: Fix 405EX PCIe UTLSET register setup
Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-13 08:06:11 +01:00
Matthias Fuchs
9be659ac08 ppc4xx: Make USB working with CONFIG_4xx_DCACHE defined
This patch disables the 44x d-cache on 'usb start' and
reenables it on 'usb stop'. This should be seen as a
temporary fix until the generic usb-ohci driver can
life with d-cache enabled.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-09 16:42:15 +01:00
Matthias Fuchs
fbde2169d2 ppc4xx: Remove redundant code from 4xx network driver
This patch removes some redundant code and decrements the end
address of cache flush and invalidate by 1.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-09 16:42:15 +01:00
Stefan Roese
c7f69c3402 ppc4xx: Make output a little shorter on I2C bootrom detection
Most 4xx PPC capable of using an I2C bootrom for bootstrap setting
already print a line with the information which I2C bootrom is
used for bootstrap configuration. So we don't need this extra line
with "I2C boot EEPROM en-/dis-abled".

This patch also has a little code cleanup integrated.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-09 12:18:54 +01:00