Depending on the boot source, set different CLI prompts. This will help
the user to figure out in which mode the bootloader was started. There
are two special modes: failsafe and SDHC boot.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
During startup the SPL will print where the u-boot proper is read from.
Instead of using the default names, provide more user friendly names.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The board is able to boot from the following source:
- user-updateble SPI flash
- write-protected part of the same SPI flash
- eMMC
- SD card
Implement the needed function hooks to support all of these boot
sources.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add CAAM support, which is required when enabling HAB secure boot.
Select CONFIG_SPL_DRIVERS_MISC so that CONFIG_IMX_HAB could
build successfully, if selected.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
The board supports up to 8 GiB memory. The memory is soldered on the
board but the configuration is equivalent to a dual chip select, dual
rank DIMM module.
Signed-off-by: Michael Walle <michael@walle.cc>
With a 8GiB memory board, it seems that the "very unlikely event" of a
DDR initialization with non-optimal values are not really that unlikely.
It happens in about every other reboot. As described in erratum
A-009942, preset the DEBUG_28 register with an optimal value. The value
iself depends on the memory configuration of the board, but the used
value seems to work well for all variants.
Signed-off-by: Michael Walle <michael@walle.cc>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Enable CONFIG_DM_SERIAL. uart and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_init to make sure driver
model work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
For now, this only provides reset and poweroff functions.
Signed-off-by: Michael Walle <michael@walle.cc>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add a structure which defines the information that is needed for
executing capsule updates on a platform. Some information in the
structure like the dfu string is used for making the update process
more robust while some information like the per platform image GUIDs
is used for fixing issues. Initialise this structure in the board
file, and use the information for the capsule updates.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
LS(1021/1012/1028/1043/1046/1088/2088), LX2160, LX2162
platforms are enabled with JR driver model.
removed sec_init() call from board files.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
This board has an internal watchdog which supervises the board startup.
Although, the initial state of the watchdog is configurable, it is
enabled by default. In board_late_init(), which means almost everything
worked as expected, disable the watchdog.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Most of the time it is very useful to have the version of the board
management controller. Now that we have a driver, print it during
startup.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The current console output is:
DRAM: 4 GiB
DDR 4 GiB (DDR3, 32-bit, CL=11, ECC on)
The size is printed twice and we can save one line of console output if
we join both lines. The new output is as follows:
DRAM: 4 GiB (DDR3, 32-bit, CL=11, ECC on)
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The function wrongly will return the card detection status of the SD card
(USDHC2) for the eMMC (USDHC1). Thus booting from eMMC without an inserted
SD card will fail.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
This is supposed to be a build-system flag. Move it there so we can
define it before linux/kconfig.h is included.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since no one uses this feature and I am not aware of any parsers of this
in Linux, remove it.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Michael Walle <michael@walle.cc>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
I'd like to keep informed about ls1028a.dtsi changes. For now, there is
no top-level entry for any layerscape specific files. Instead, add the
file entry to my board MAINTAINERS file.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The Kontron SoM-Line i.MX8MM (N801x) by Kontron Electronics GmbH is a SoM
module with an i.MX8M-Mini SoC, 1/2/4 GB LPDDR4 RAM, SPI NOR, eMMC and PMIC.
The matching evaluation boards (Board-Line) have 2 Ethernets, USB 2.0, HDMI/LVDS,
SD card, CAN, RS485 and much more.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
This adds support for i.MX6UL/ULL-based evaluation kits with SoMs by
Kontron Electronics GmbH.
Currently there are the following SoM flavors (SoM-Line):
* N6310: SOM with i.MX6UL-2, 256MB RAM, 256MB SPI NAND
* N6311: SOM with i.MX6UL-2, 512MB RAM, 512MB SPI NAND
* N6411: SOM with i.MX6ULL, 512MB RAM, 512MB SPI NAND
And the according evaluation boards (Board-Line):
* N6310-S: Baseboard with SOM N6310, eMMC, display (optional), ...
* N6311-S: Baseboard with SOM N6311, eMMC, display (optional), ...
* N6411-S: Baseboard with SOM N6411, eMMC, display (optional), ...
Currently U-Boot describes i.MX6UL and i.MX6ULL through separate config
options at compile-time. Though the differences are so minor, that for
the scope of these SoMs we just use a single defconfig that is compatible
with both SoCs.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
It is a pain to have to specify the value 16 in each call. Add a new
hextoul() function and update the code to use it.
Add a proper comment to simple_strtoul() while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes it is desireable to have the console output on the first
serial line. Introduce a configuration option for it (in the board
scope).
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable SATA support. Although not supported by the usual SATA pins on
the SMARC baseboard connector, SATA mode is supported on a PCIe lane.
This way one can use a mSATA card in a Mini PCI slot.
We need to invert the received data because in this mode the polarity of
the SerDes lane is swapped. Provide a fixup in board_early_init_f() for
the SPL. board_early_init_f() is then not common between SPL and u-boot
proper anymore, thus common.c is removed, as it just contained said
function.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Although this variant has two external network ports, they are not (yet)
supported by the bootloader because they are connected via an internal
network switch. Otherwise its the same as the other variants.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This variant has one network port connected via RGMII and doesn't have
any TSN capabilities out-of-the-box. Instead it has all four SerDes
lanes available for customer use.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The board supports 16 configuration bits which can be manipulated with
this command. See the board's README for a detailed explanation on each
bit.
Signed-off-by: Michael Walle <michael@walle.cc>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add basic support for the Kontron SMARC-sAL28 board. This includes just
the bare minimum to be able to bring up the board and boot linux.
For now, the Single and Dual PHY variant is supported. Other variants
will fall back to the basic variant.
In particular, there is no watchdog support for now. This means that you
have to disable the default watchdog, otherwise you'll end up in the
recovery bootloader. See the board README for details.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
