arch/x86/lib/string.c contains assembler implementations of memcpy(),
memmove(), and memset() written for i386. Don't use it on x86_64.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Refactor the switch from supervisor to hypervisor to a new function called
at the beginning of do_bootefi().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
ARMv7-M only supports the Thumb instruction set. Our current crt0 code does
not support it. With the patch we can build all unit tests of the EFI
subsystem that do not require crt0.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Basin Cove PMIC is connected to I2C0 bus which is hidden from the OS
and access is going via SCU device, enumerated via PCI.
For now, we add just a minimum support of PMIC device to allow enabling,
e.g. USB OTG, in the OS.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
It is unnecessary to use a RAM version GDT for 64-bit U-Boot proper.
In fact we can just use the ROM version directly, which not only
eliminates the risk of being overwritten by application, but also
removes the complexity of patching the cpu_call64().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Before jumping to 64-bit U-Boot proper, SPL copies the cpu_call64()
function to a hardcoded address 0x3000000. This can have potential
conflicts with application usage. Switch the destination address
to be allocated from the heap to avoid such risk.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present the 4-level page table base address for 64-bit U-Boot
proper is assigned an address that conflicts with CONFIG_LOADADDR.
Change it to an address within the low memory range instead.
Fixes crashes seen when 'dhcp' on QEMU x86_64 with
"-net nic -net user,tftp=.,bootfile=u-boot".
Reported-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The PCIe slot PERST signal is active low. Fix the gpio signal
description in the dts.
This happened to work because the pcie_dw_mvebu driver sets the reset
gpio level to 1 (high) to release the reset. The following commit will
fix that.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Common sound support
buildman environment support
of-platdata documentation improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlxf7igRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYKfggApQiL0Gv6NdGAQN+zfpjKY5a2QyjKsAxa
KLm3q8XyXIQXufMWOEPoW1iWm0iixpIFgChy8ff3m/OPDzsx99UXDTyvjitsSxtQ
5tFu8K78nUZT6OOE3HNhhlyW/xK442oKBzGt4MUt3kUZOELsCNuftgbJUWksHuO3
6pPrgt36E0uRGbUA4ioYCU336viJRPOOCdqb8hHViEihFj/IEv5T82RdE5y97YxG
dT7BZxjPkBH5ZN1uD/tdxG1k6IZBagZiYoDAsYp4YqNwmVsm5sLrZ9QVSf7EcH/y
qX8butZesiMd7xm7RROlrIImh7fb36N3zsoRiUWZDo1Al3IRkmZyVA==
=tdut
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-10feb19' of git://git.denx.de/u-boot-dm
Samsung sound patches (applied for Samsung maintainer)
Common sound support
buildman environment support
of-platdata documentation improvements
Now that these boards use driver model we can drop the old code. At
present s5p_mmc_init() is still used by goni and smdkv310 so cannot be
removed unless we remove those boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Update the flashmap so that this board can be started over USB A-A. It
is slightly different from snow.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Update the spring settings to use this codec, which is what it actually
shipped with.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Move all exynos boards over to use CONFIG_BLK.
This converts s5p_goni also, but adding dummy functions for pinmux and
peripheral ID. This will not function correctly, but gives the maintainer
more time to convert the board if desired.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Perform some cosmetic cleanup of the ATF image startup function, namely
fixing a spelling mistake, capitalization of a few words, spacing, as
well aligning how errors are printed and as using panic() for cases that
were using a combination of printf() + hang().
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
This add the initial support of the broadcom reference
board bcm963158 with a bcm63158 SoC.
This board has 1 GB of ram, 512 MB of flash (nand),
2 usb port, 1 uart, 4 ethernet ports (LAN), 1 ethernet port (WAN).
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
This add the initial support of the broadcom bcm63158 SoC family,
only the cpu, dram and uart are supported.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
- Add st,digbypass on clk_hse node (needed for board rev.C)
- MLAHB/AHB max frequency increased from 200 to 209MHz, with:
- PLL3P set to 208.8MHz for MCU sub-system
- PLL3Q set to 24.57MHz for 48kHz SAI/SPI2S
- PLL3R set to 11.29MHz for 44.1kHz SAI/SPI2S
- PLL4P set to 99MHz for SDMMC and SPDIFRX
- PLL4Q set to 74.25MHz for EVAL board
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Now that new SPI NOR layer uses stateless 4 byte opcodes by default,
don't enable SPI_FLASH_BAR. For SPI controllers that cannot support
4-byte addressing, (stm32_qspi.c, fsl_qspi.c, mtk_qspi.c, ich.c,
renesas_rpc_spi.c) add an imply clause to enable SPI_FLASH_BAR so as to
not break functionality.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
commit fdce9d35dc ("arm: dts: am33xx: Sync dts with Linux 4.20.0")
did remove the "u-boot,dm-spl" flag from the 'ocp' bus which was
introduced with
commit 19aa4ac09d ("dts: am33xx: add u-boot, dm-spl to ocp bus")
Due to this all boards having CONFIG_SPL_OF_CONTROL enabled are broken
because they cannot bind/probe the boot-media interface during SPL
stage.
This commit introduces the 'am33xx-u-boot.dtsi' which is included with
the auto include mechanism. The am33xx-u-boot-dtsi adds the important
"u-boot,dm-pre-reloc" to the 'ocp bus' (the root bus of almost all
peripherals, at least the bootable ones).
The peripherials (mmc, spi, ...) needed during SPL stage need to be
equipped with the 'u-boot,dm-pre-reloc' in their responsible dts file.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
With the new DM_VIDEO support in the Armada XP LCD driver, this patch
adds the needed DT node for the LCD controller to the theadorable dts
file. This DT property is not added to the Armada XP dtsi files, as this
LCD feature is pretty unusual for this SoC and I personally know of no
other board that uses this controller.
This patch also enables CONFIG_BMP_16BPP/24BPP/32BPP, as the "old" bmp
command supported these BMP files.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
This patch moves the Armada XP video / LCD driver to DM_VIDEO. With this
move, the legacy interface board_video_init() is removed from the
theadorable board code (only user of this video driver). The support
via DT will be added in a separate patch.
This patch also enables DM_VIDEO for the theadorable board, as this is
needed to not break git bisect'ability.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
This adds initial support for micro-DPU (uDPU) board which is based on Armada-3720 SoC.
micro-DPU is the single-port FTTdp "distribution point unit" made by Methode Electronics
which offers complete modularity with replaceable SFP modules both for uplink and downlink
(G.hn over twisted-pair, G.hn over coax, 1G and 2.5G Ethernet over Cat-5e cable).
On-board features:
- 512 MiB DDR3
- 2 x 2.5G SFP via HSGMII SERDES interface to the A3720 SoC
- USB 2.0 Type-C connector
- 4GB eMMC
- ETSI TS 101548 reverse powering via twisted pair (RJ45) or coax (F Type)
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Luis Torres <luis.torres@methode.com>
Cc: Scott Roberts <scott.roberts@telus.com>
Cc: Paul Arola <paul.arola@telus.com>
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Now that the PCIe driver supports DM and DT parsing, enable the PCIe DT
nodes that are used by this board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: VlaoMao <vlaomao@gmail.com>
This patch sync's the PCIe DT nodes with the recent Linux v4.20 version.
This change makes it easier to reference specific PCIe nodes in the
board dts files to e.g. enable a PCIe port as this is now necessary with
the new DM PCI driver for these platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: VlaoMao <vlaomao@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
* support for Chromebook Bob
* full pinctrl driver using DTS properties
* documentation improvements
* I2S support for some Rockchip SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcVG0IAAoJECaAFcEOcohNKVAIAJd3DN/qudcVQdkuvAGK6WIk
Umxkm6rxHwur7oU+wxvK1p1l/0YTFBeCfo15quH1DkSc/WIUnmBlLmDvqpGVmPmh
ydZNE9ZChn0OKRIaM6pKJr+3p155cQDe6Mgg2j/5CnNx28KxT+vu7EqZbZvbQPag
wcZEK6Z6E5jMVHVn2lbLgmsBPmY7ksX168IqpvzTxIj0a4J3n0DcJUnO4RBBS0Q2
PGEvFhTvigVWs6r6GL0gLn3VwnQX30xQlIuKKORPcdhjk97cJcS4+bRxdTENTKD9
j3+pgyl1n04O8sPONZS7pH3fvJwtC6SwnoxTYxGrvjedw1LxbyHG3cqcGDg/TJ8=
=ik3X
-----END PGP SIGNATURE-----
Merge tag 'for-master-20190201' of git://git.denx.de/u-boot-rockchip
u-boot-rockchip changes for 2019.04-rc1:
* support for Chromebook Bob
* full pinctrl driver using DTS properties
* documentation improvements
* I2S support for some Rockchip SoCs
With the latest changes to add support for the Chromebook Bob,
initialisation through debug_uart_init() did no longer get called for
other targets.
Fix this, by moving debug_uart_init() out of the Bob-specific
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Bob is a 10-inch chromebook produced by Asus. It has two USB 3.0 type-C
ports, 4GB of SDRAM, WiFi and a 1280x800 display. It uses its USB ports
for both power and external display. It includes a Chrome OS EC
(Cortex-M3) to provide access to the keyboard and battery functions.
Support so far includes only:
- UART
- SDRAM
- MMC, SD card
- Cros EC (but not keyboard)
Not included:
- Keyboard
- Display
- Sound
- USB
- TPM
Bob is quite similar to Kevin, the Samsung Chromebook Plus, but support
for this is not provided in this series.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add some U-Boot-specific settings. These should really go in the
*u-boot.dtsi file, but it seems that rk3399 does not use that yet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Allow rockchip boards to use GPIOs before driver model is ready. This is
really only useful for setting GPIOs to enable the early debug console, if
needed on some platforms.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
At present this enum is only available to rk3288. Move it so that other
rockchip SoCs can access it. It is needed for the SPL GPIO driver for
rk3999 in a later patch.
Also adjust the enum name to lower case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
These board files have inconsistent #include ordering. Fix them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This memory is used on Bob. Add settings for this, taken from coreboot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The u-boot,spl-boot-device property only allows MMC at present. Add SPI as
well for boards that boot from SPI flash.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This file has changed upstream, with some additions and changes. Move the
U-Boot version towards this.
Some USB changes seem to be incompatible with how the bindings work on
rockchip in U-Boot. Testing is needed to make sure that USB still works
correct, and adjust the code (not device tree) if not.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Bring in these files from Linux v4.20.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
To match the iomux setting of uart2 at SPL, correct the uart2
default pin configuration, if not changed, the evb-rk3229 can't
output the log message.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
If we use the new pinctrl driver, the pinctrl setup will be done
by device probe. Remove the pinctrl setup at rk3288-board-spl.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
It seems that pinctrl is not requested for rk3188 SPL, remove it so
that can save more space for SPL image size.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
When the boot ROM sets up MMC we don't need to do it again. Remove the
MMC setup code entirely, but we also need to enable uart for debug message.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This adds support for the ASUS C201, a RK3288-based clamshell
device. The device tree comes from linus's linux tree at
3f16503b7d2274ac8cbab11163047ac0b4c66cfe. The SDRAM parameters
are for 4GB Samsung LPDDR3, decoded from coreboot's
src/mainboard/google/veyron/sdram_inf/sdram-lpddr3-samsung-4GB.inc
Signed-off-by: Marty E. Plummer <hanetzer@startmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Like on rk3399-puma we want to continue booting the fill U-Boot from
the same device as the SPL stage.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This function causes a 5-second delay and stops the display working on
minnie. This code should be in a driver and should only be enabled by
a device-tree property, so that it does not affect devices which do not
have this feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
