Commit graph

86 commits

Author SHA1 Message Date
Masahiro Yamada
4e1aa8437a armv7: convert makefiles to Kbuild style
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-10-31 12:53:39 -04:00
Wolfgang Denk
d4c8aa9cb4 Coding Style cleanup: remove trailing empty lines
Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-10-14 16:06:54 -04:00
Albert ARIBAUD
8d20836615 arm: omap3: fix SRAM copy and execution sequence
Fix size calculation in copy of go_to_speed into SRAM.
Use SRAM_CLK_CODE in call to SRAM-based go_to_speed.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2013-08-28 11:44:58 -04:00
Naumann Andreas
a704a6d615 ARM: omap3: Implement dpll5 (HSUSB clk) workaround for OMAP36xx/AM/DM37xx according to errata sprz318e.
In chapter 'Advisory 2.1 USB Host Clock Drift Causes USB Spec Non-compliance in Certain Configurations' of the TI Errata it is recommended to use certain div/mult values for the DPLL5 clock setup.
So far u-boot used the old 34xx values, so I added the errata recommended values specificly for 36xx init only.
Also, the FSEL registers exist no longer, so removed them from init.

Tested this on a AM3703 board with 19.2MHz oscillator, which previously couldnt lock the dpll5 (kernel complained). As a consequence the EHCI USB port wasnt usable in U-Boot and kernel. With this patch, kernel panics disappear and USB working fine in u-boot and kernel.

Signed-off-by: Andreas Naumann <anaumann@ultratronik.de>
[trini: Add extern to <asm/arch-omap3/clock.h>
Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15 09:09:29 -04:00
Andreas Bießmann
c4ec281822 omap3/sys_info: fix printout of OMAP36XX L3 freqency
The OMAP36xx/OMAP37xx family uses L3 frequency of 200MHz instead of 165MHz
used by OMAP34xx/OMAP35xx.

Also fix checkpatch warning about alignment.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-07-26 16:39:10 -04:00
Stefan Roese
bf0e86606d arm: omap3: spl: Fix problem with 8bit NAND devices
Currently in OMAP3 SPL, the GPMC for NAND is configured for 16bit
access. This patch adds support for 8bit NAND devices as well.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
2013-07-26 16:39:10 -04:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Lokesh Vutla
af1d002f89 ARM: OMAP2+: Rename asm/arch/clocks.h asm/arch/clock.h
To be consistent with other ARM platforms,
renaming asm/arch-omap*/clocks.h to asm/arch-omap*/clock.h

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:09 -04:00
man.huber@arcor.de
9d0fd10ca1 omap3: Display MHz instead of mHz on the console
The processor is hopefully running with M(ega)Hz and not with m(illi)Hz.

Signed-off-by: Manfred Huber <man.huber@arcor.de>
2013-04-12 15:29:23 -04:00
Andreas Bießmann
da634ae356 omap_gpmc: change nandecc command
With uppcoming BCH support on OMAP devices we need to decide between differnt
algorithms when switching the ECC engine.  Currently we support 1-bit hammign
and 8-bit BCH on HW backend.

In order to switch between differnet ECC algorithms we need to change the
interface of omap_nand_switch_ecc() also.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Thomas Weber <thomas.weber.linux@googlemail.com>
2013-04-08 11:29:05 -04:00
Enric Balletbo i Serra
b51a5e3a0a OMAP3: Initialize gpmc if SPL_ONENAND_SUPPORT is enabled.
In order to use SPL boot from OneNAND we should initialize the gpmc.

Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
2013-03-11 11:06:08 -04:00
Nikita Kiryanov
e3913f56a2 omap_hsmmc: add driver check for write protection
Add check for write protection in omap mmc driver.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-08 16:41:13 -05:00
Nikita Kiryanov
e874d5b001 omap_hsmmc: implement driver check for card detection
Implement driver check for card detection.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2013-03-08 16:41:13 -05:00
Albert ARIBAUD
79f3877794 Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'
This required manual merging drivers/mtd/nand/Makefile
and adding am335x_evm support for CONFIG_SPL_NAND_DRIVERS
2013-01-08 13:15:45 +01:00
Robert P. J. Day
e3fe62574d omap3: Add a few comments to "#endif"s for readability.
No functional changes, just more comments for readability when a
preprocessor check spans more than a few lines, and for consistency.

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2012-12-10 08:55:25 -07:00
Peter Barada
8c4445d266 Pass sdrc timing values through board_sdrc_timings structure
Instead of passing individual registers by value to board_get_mem_timings,
pass a board_mem_timings structure pointer for the board files to fill in.
Pass same structure pointer to write_sdrc_timings.  This saves about
90 bytes of space in SPL.

Signed-off-by: Peter Barada <peter.barada@logicpd.com>
2012-12-10 08:54:02 -07:00
Andreas Bießmann
4af9e675fa omap3/mem.c: remove unused defines
These GPMC_CS defines are a leftover from prior gpmc_init(). Commit 187af954
removed the need for these definitions but missed to remove them.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Tom Rini <trini@ti.com>
2012-12-10 08:54:01 -07:00
Ilya Yanok
08fc71711a OMAP3: am35x: add musb functions
AM35XX specific functions for integrated USB PHY/MUSB IP.

Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-11-20 00:16:07 +01:00
Tom Rini
57f588be60 omap3: Rework board.c for !CONFIG_SYS_L2CACHE_OFF
When CONFIG_SYS_L2CACHE_OFF is defined we end up with a few warnings
currently.  Re-order functions so that we don't have that anymore.

Signed-off-by: Tom Rini <trini@ti.com>
2012-10-30 22:23:28 -07:00
Albert ARIBAUD
dec96689ca arm: armv7: omap3: Fix restore sequence in lowlevel_init
The restore sequence in lowlevel_init was in the wrong order,
causing lr to lose its original value and be set equal to ip
instead. Also, its use of the stack clashes with that of
s_init, so move the s_init call after the restore and turn
it  into a tail-optimized branch.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2012-10-08 11:15:04 -07:00
Tom Rini
6507f133f3 SPL: Create arch/arm/lib/spl.c for board_init_f and jump_to_image_linux
In SPL (CONFIG_SPL_FRAMEWORK) board_init_f must setup the stack pointer,
clear the BSS and call board_init_r.  We mark this as weak as some
platforms may need to perform additional initalization at this point.
We provide a gd that we know will be in a usable location, once the BSS
has been cleared to help with this as well.  Finally, we no longer call
relocate_code so remove that from the armv7 version.

Next, both board_init_f and jump_to_image_linux are going to be
inherently arch-specific, so move these versions to arch/arm/lib/spl.c

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:49:59 -07:00
Tom Rini
47f7bcae8c SPL: Move the omap SPL framework to common/spl
Add a new flag, CONFIG_SPL_FRAMEWORK to opt into the common/spl SPL
framework, enable on all of the previously using boards.  We move the
spl_ymodem.c portion to common/ and spl_mmc.c to drivers/mmc/.  We leave
the NAND one in-place as we plan to replace it later in this series.

We use common/spl to avoid linker problems with respect to merging
constant strings in objects.   Otherwise all strings in common/ will be
linked in and kept which grows SPL in size too much.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:49:59 -07:00
Tom Rini
d7cb93b28a ARM: SPL: Move gpmc_init() to spl_board_init()
This is an OMAP/related-specific function, move calling it to
spl_board_init() and turn on CONFIG_SPL_BOARD_INIT on the boards that
enabled NAND and didn't enable this already.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:49:59 -07:00
Tom Rini
f0881250f9 ARM: SPL: Make spl_mmc.c more generic
Move the default omap/related-centric board_mmc_init to
arch/arm/cpu/armv7/omap-common/boot-common.c and move the type defines
to <asm/spl.h>.  Also use mmc->read_bl_len rather than MMCSD_SECTOR_SIZE

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:49:58 -07:00
Tom Rini
55cdbb8d4e ARM: SPL: Add <asm/spl.h> and <asm/arch/spl.h>
Move the SPL prototypes from <asm/omap_common.h> into <asm/spl.h> and
add <asm/arch/spl.h> for arch specific portions of CONFIG_SPL_FRAMEWORK.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:49:57 -07:00
Tom Rini
8082fda9fc ARM: SPL: Remove NAND_MODE_HW_ECC from spl_nand.c
This detection code doesn't (and can't) do anything currently, so
remove.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:48:39 -07:00
Tom Rini
37189a1958 ARM: SPL: Rename omap_boot_mode to spl_boot_mode()
Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:48:39 -07:00
Tom Rini
8e1b836ec5 ARM: SPL: Rename omap_boot_device to spl_boot_device
Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:48:38 -07:00
Matt Porter
a3c3fabb0f arm, omap3: fix warm reset serial output on OMAP36xx/AM/DM37xx
In warm reset conditions on OMAP36xx/AM/DM37xx the rom code
incorrectly sets the DPLL4 clock input divider to /6.5 which
is an invalid value unless the input clock is 13MHz. When a JTAG
emulator is attached, a warm reset is necessary after the emulator
gains control of the process. This results in a loss of serial
output due to the invalid DPLL4 settings.

This patch fixes the issue by resetting the DPLL4 clock input
divider to /1 when the input clock is not 13MHz. AM/DM37x TRM
section 3.5.3.3.3.2.1 specifies that the /6.5 setting is only
used when the input clock is 13MHz.

Signed-off-by: Matt Porter <mporter@ti.com>
2012-05-15 08:31:41 +02:00
Tom Rini
8a87a3d72e omap3: Introduce weak misc_init_r
Introduce a __weak misc_init_r function that just runs dieid_num_r().
Remove misc_init_r from cm_t35, mcx, omap3_logic and mt_ventoux as this was
all they did for misc_init_r.

Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Peter Barada <peter.barada@logicpd.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2012-05-15 08:31:28 +02:00
Aneesh V
74236acacc armv7: add appropriate headers for assembly functions
Use ENTRY and ENDPROC with assembly functions to ensure
necessary assembler directives for all functions.

Signed-off-by: Aneesh V <aneesh@ti.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-05-15 08:31:26 +02:00
Tom Rini
33fbc9cf82 sdrc.c: Fix typo in do_sdrc_init() for SPL
We need to setup CS0 and CS1 not CS0 and CS0 again.

Signed-off-by: Tom Rini <trini@ti.com>
2012-03-29 08:19:29 +02:00
Stefano Babic
da521387a4 OMAP3: SPL: do not call I2C init if no I2C is set.
Call i2c initialization in spl_board_init only if I2C
is configured for the board.

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tom Rini <tom.rini@gmail.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Simon Schwarz <simonschwarzcor@gmail.com>
2012-03-27 22:05:29 +02:00
Aneesh V
f1f2c3ca9f armv7: omap3: leave outer cache enabled
Mainline kernel for OMAP3 doesn't enable L2 cache
It expects L2$ to be enabled by ROM-code/bootloader.

Leaving L2$ enabled can be troublesome in cases where
the L2 cache is not under CP15 control, such as in
Cortex-A9. This problem is explained in detail in
the commit dc7100f408

However, this problem doesn't apply to Cortex-A8
because L2$ in Cortex-A8 is under CP15 control and
hence the generic armv7 maintenance opertions work
for it.

As such we can make an exception for OMAP3 and
leave the L2$ enabled when we jump to kernel. This
is done by removing the strongly-linked implementation
of v7_outer_cache_disable() and allowing it to fall
back to the weakly linked implementation that doesn't
do anything.

Signed-off-by: Aneesh V <aneesh@ti.com>
2012-02-27 21:19:25 +01:00
Peter Meerwald
a4958313fb omap3: fix comment typos
Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>
2012-02-12 10:11:32 +01:00
Govindraj.R
95f8791042 OMAP3+: Clock: Adding ehci clock enabling
Adding ehci clock enabling mechanism part of clock framework.
When essential clocks are enabled during init phase usb host
clocks can also be enabled from clock framework.

Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Tested-by: Stefano Babic <sbabic@denx.de>
2012-02-12 10:11:31 +01:00
Tom Rini
0ae056510f OMAP3: Correct get_sdr_cs_offset mask
The function get_sdr_cs_offset reads the CS_CFG register in the SDRC
to determine where CS1 is mapped to.  make_cs1_contiguous() will set
CS1 to follow after CS0.  The CS_CFG register has values in bits 9:8
and 3:0 but we had erroneously been testing 5:4 and 3:0 resulting in
incorrect offsets on platforms with less than 128MB as 3:0 describe
128MB hunks and 9:8 describe 32MB offsets after the 128MB hunk.

Tested-by: Grant Erickson <marathon96@gmail.com>
Signed-off-by: Tom Rini <trini@ti.com>
2012-02-12 10:11:23 +01:00
Pali Rohár
204705111c arm: omap3: Define save_boot_params in lowlevel_init.S for SPL only
Wrap the function save_boot_params with CONFIG_SPL_BUILD.  This will
allow non-SPL boards to define their own save_boot_params functions
in U-Boot itself.

Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
2012-02-12 10:11:22 +01:00
Andreas Müller
8775471bb3 OMAP SPL: call timer_init in s_init to make udelay work earlier
Signed-off-by: Andreas Müller <schnitzeltony@gmx.de>
2012-01-16 08:40:12 +01:00
Nikita Kiryanov
715462dd7e omap3: make get_board_rev() function weak
Current get_board_rev() function returns a hard coded value which is
obviously incorrect for the majority of boards.
Allow boards to provide a correct implementation by making this function
weak.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2012-01-16 08:40:11 +01:00
Tom Rini
ee08a8260a OMAP3: Add SPL_BOARD_INIT hook
Add an SPL_BOARD_INIT hook and for OMAP3 have it turn on i2c.  OMAP4
doesn't need i2c enabled in SPL.  Enable SPL_BOARD_INIT on devkit8000.

Cc: Frederik Kriewitz <frederik@kriewitz.eu>
Signed-off-by: Tom Rini <trini@ti.com>
2011-12-06 23:59:39 +01:00
Tom Rini
4e647e1207 OMAP3 SPL: Add identify_nand_chip function
A number of boards are populated with a PoP chip for both DDR and NAND
memory.  Other boards may simply use this as an easy way to identify
board revs.  So we provide a function that can be called early to reset
the NAND chip and return the result of NAND_CMD_READID.  All of this
code is put into spl_id_nand.c and controlled via CONFIG_SPL_OMAP3_ID_NAND.

Signed-off-by: Tom Rini <trini@ti.com>
2011-12-06 23:59:38 +01:00
Tom Rini
9ae0d55074 OMAP3 SPL: Rework memory initalization and devkit8000 support
This changes to making the board be responsible for providing the
memory initialization timings in SPL and converts the devkit8000
to this framework.  In SPL we try and initialize both CS0 and CS1.

Cc: Frederik Kriewitz <frederik@kriewitz.eu>
Signed-off-by: Tom Rini <trini@ti.com>
2011-12-06 23:59:38 +01:00
Tom Rini
3bd8437dcc OMAP3: Change mem_ok to clear again after reading back
It's possible to need to call this function on the same banks multiple
times so we want to be sure that 'pos A' is cleared out again at the
end.

Signed-off-by: Tom Rini <trini@ti.com>
2011-12-06 23:59:38 +01:00
Tom Rini
2a04e85870 OMAP3: Add a helper function to set timings in SDRC
Since we go through the sequence to setup the SDRC timings more than
once, break this logic out into its own function and have that function
call mem_ok() to make sure the memory is usable.

Signed-off-by: Tom Rini <trini@ti.com>
2011-12-06 23:59:38 +01:00
Tom Rini
5f862b7179 OMAP3: Update SDRC dram_init to always call make_cs1_contiguous()
We update the comment in make_cs1_contiguous() to be a little bit
more clear (it's been copy/pasted from other silicons) and then
explain in dram_init() why we need to always try this.

Note that in the previous behavior we were always calling this on
boards that never had cs1 populated anyhow so making sure we do
this always is fine and will correct things like omap3evm detecting
an invalid amount of memory (384MB).

Signed-off-by: Tom Rini <trini@ti.com>
2011-12-06 23:59:37 +01:00
Tom Rini
b7eb9e7895 omap3: mem: Comment enable_gpmc_cs_config more
Expand the "enable the config" comment to explain what the bit shifts
are and define out two of the magic numbers.

Signed-off-by: Tom Rini <trini@ti.com>
2011-12-06 23:59:37 +01:00
Ilya Yanok
b9e65a797b AM35xx: add EMAC support
AM35xx has DaVinci-compatible EMAC.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
2011-12-06 23:59:36 +01:00
Aneesh V
e4fce34e7a start.S: remove omap3 specific code from start.S
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Aneesh V <aneesh@ti.com>
Acked-by: Tom Rini <trini@ti.com>
2011-12-06 23:59:34 +01:00
Alexander Holler
86623add12 OMAP3: Use sdelay from arch/arm/cpu/armv7/syslib.c instead of cloning that.
There is no need to have such a function twice.

Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-11-29 15:43:38 +01:00