Commit graph

49053 commits

Author SHA1 Message Date
Cyrille Pitchen
9bcb018870 Revert "sf: Fix quad bit set for micron devices"
This reverts commit c56ae7519f.

Once the 'Quad Enable' bit is cleared in their Enhanced Volatile
Configuration Register (EVCR), Micron memories expect ALL commands to use
the SPI 4-4-4 protocol. Commands using SPI 1-y-z protocols are no longer
accepted.

Within the reverted commit, the write_evcr() function is implemented using
the spi_flash_write_common(), which is a shortcut for the
[ spi_flash_cmd_write_enable(), spi_flash_cmd_write(),
spi_flash_cmd_wait_ready() ] sequence.

Since the internal state of the Micron memory has been changed when the
spi_flash_cmd_write() function completes, the later call of the
spi_flash_cmd_wait_ready() function fails.

Indeed the SPI controller driver is not aware of the SPI protocol switch.

Further patches will fix the support of Micron QSPI memories.

Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
[Rebase on master, use JEDEC_MFR(info) in place of idcode0]
Signed-off-by: Jagan Teki <jagan@openedev.com>
2016-12-15 18:33:16 +01:00
Phil Edworthy
db9225ba26 sf: Do not force the DT memory map size to exactly match the device
As long as the memory mapped size specifeid in the DT is the same or
bigger than the device size, it will work. So do not force the sizes
to be identical.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:57:28 +01:00
Fabien Parent
304decdd31 mtd: spi: don't return -1 when scan succeed
In spi_flash_scan, 'ret' is initialled to -1, but 'ret' is not always
used to store a return value, in that case, even when the function
succeed, an error (-1) will be returned.
Lets just return 0 if we hit the end of the function.

Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:57:28 +01:00
Phil Edworthy
6d72810c66 spi: cadence_qspi: Move DT prop code to match layout
Move the code to read the "sram-size" property into the other code
that reads properties from the node, rather than the SF subnode.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:57:28 +01:00
Phil Edworthy
22e63ff3a2 spi: cadence_qspi: Fix CS timings
The Cadence QSPI controller has specified overheads for the various CS
times that are in addition to those programmed in to the Device Delay
register. The overheads are different for the delays.

In addition, the existing code does not handle the case when the delay
is less than a SCLK period.

This change accurately calculates the additional delays in Ref clocks.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:57:27 +01:00
Phil Edworthy
3c56953219 spi: cadence_qspi: Remove returns from end of void functions
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:57:27 +01:00
Phil Edworthy
7d403f284c spi: cadence_qspi: Use spi mode at the point it is needed
Instead of extracting mode settings and passing them as separate
args to another function, just pass the SPI mode as an arg.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:57:27 +01:00
Phil Edworthy
7e76c4b08a spi: cadence_qspi: Clean up the #define names
A lot of the #defines are for single bits in a register, where the
name has _MASK on the end. Since this can be used for both a mask
and the value, remove _MASK from them.

Whilst doing so, also remove the unnecessary brackets around the
constants.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:57:27 +01:00
Phil Edworthy
db37cc9c39 spi: cadence_qspi: Use #define for bits instead of bit shifts
Most of the code already uses #defines for the bit value, rather
than the shift required to get the value. This changes the remaining
code over.

Whislt at it, fix the names of the "Rd Data Capture" register defs.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:57:27 +01:00
Phil Edworthy
0ceb4d9e9a spi: cadence_qspi: Better debug information on the SPI clock rate
Show what the output clock rate actually is.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:57:27 +01:00
Phil Edworthy
32068c42a7 spi: cadence_qspi: Fix baud rate calculation
With the existing code, when the requested SPI clock rate is near
to the lowest that can be achieved by the hardware (max divider
of the ref clock is 32), the generated clock rate is wrong.
For example, with a 50MHz ref clock, when asked for anything less
than a 1.5MHz SPI clock, the code sets up the divider to generate
25MHz.

This change fixes the calculation.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:57:27 +01:00
Phil Edworthy
cc80a897e4 spi: cadence_qspi: Fix clearing of pol/pha bits
Or'ing together bit positions is clearly wrong.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:57:27 +01:00
Simon Glass
1b7c28f514 spi: Add error checking for invalid bus widths
At present an invalid bus width prints a message but does not return an
error. This is the opposite of the correct behaviour. Adjust it to avoid
code bloat in the common case, and avoid hard-to-debug failure in the
uncommon case.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:38:30 +01:00
Vignesh R
f06e1588fb ARM: dts: am437x-idk: Fix QSPI compatible string
Unlike Linux kernel, U-Boot depends on "spi-flash" compatible to probe
m25p80 spi-nor devices. Hence, add "spi-flash" compatible string to
m25p80 node. Without this patch, flash device DT data is not parsed and
QSPI operates in unsupported mode leading to data corruption.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:38:30 +01:00
Michal Simek
41122d374f travis-ci: Add zynq_zc702 target support
It depends on qemu v2.8.0-rc3 which includes device loader property.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-12-14 19:49:04 -05:00
Lukasz Majewski
53e8ca2253 MAINTAINERS: DFU: Change e-mail address for DFU maintainer
Despite I leave Samsung by the end of the year, I'm going to maintain DFU
in u-boot.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
2016-12-12 13:03:15 -05:00
Lukasz Majewski
dea6068817 MAINTAINERS: ONENAND: MTD: Mark Samsung's OneNAND as orphaned
Since I leave Samsung by the end of the year, I will not have access to
OneNAND devices anymore.

Hence the custodian position has been marked as "Orphaned".

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
2016-12-12 10:54:37 -05:00
Tom Rini
b591730c35 Merge git://www.denx.de/git/u-boot-marvell 2016-12-12 07:19:28 -05:00
Tom Rini
fe9822556e Merge branch 'master' of git://git.denx.de/u-boot-uniphier 2016-12-12 07:18:53 -05:00
Konstantin Porotchkin
a20b7a2a53 arm64: mvebu: Enable hush parser in A8K default configuration
Enable hush parser in Armada-7040 and Armada-8040 DB default
configurations.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2016-12-12 09:05:45 +01:00
Konstantin Porotchkin
1d136726f7 arm64: mvebu: Enable PCIe support in Armada-7040 configuration
Enable PCIe bus support in Armada-7040 DB default configuration

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2016-12-12 09:05:36 +01:00
Konstantin Porotchkin
b58385df3a arm64: mvebu: Add L3 cache flush functionality to A8K family
Add missing L3 cache flush functionality which absence prevents
Linux kernel from normal boot in case the L3 cache is enabled
by ATF.
The L3 cache is named the "last level" cache in order to keep
the terminology similar to the ATF code.
This cache should not be disabled by u-boot since the Linux
kernel cannot activate it, so it is activates at ATF stage.
However the cache flush is required for preventing data corruption
after disabling the MMU and the data cache before passing control
to the loaded Linux image.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2016-12-12 09:05:28 +01:00
Konstantin Porotchkin
81647eaff3 arm64: mvebu: Enable pin control support in A8K default config
Enable mvebu pin control support in the default configuration
files for Armada-7040 and Armada-8040 development boards

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2016-12-12 09:04:52 +01:00
Konstantin Porotchkin
27bd4b159a arm64: mvebu: Enable BUBT command support in A8K default config
Enable mvebu "bubt" command support in the default configuration
file for Armada-7040 and Armada-8040 development boards

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2016-12-12 09:04:52 +01:00
Konstantin Porotchkin
f99386c5b1 arm64: mvebu: Add pin control nodes to A8K family DTS files
Add pin control nodes to APN806, CP-master, CP-slave and
Armada-7040 and Armada-8040 boards DTS files

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2016-12-12 09:04:52 +01:00
Konstantin Porotchkin
656e6cc86b arm64: mvebu: pinctrl: Add pin control driver for A8K family
Add a DM port of Marvell pin control driver.
The A8K SoC family contains several silicone dies interconnected
in a single package. Every die is normally equipped with its own
pin controller unit.
There are 2 pin controllers in A70x0 SoC and 3 in A80x0 SoC.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2016-12-12 09:04:52 +01:00
Konstantin Porotchkin
fa61ef6b49 arm64: mvebu: Add bubt command for flash image burn
Add support for mvebu bubt command for flash image
load, check and burn on boot device.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2016-12-12 09:04:52 +01:00
Konstantin Porotchkin
5b613d386a arm64: mvebu: Modify the A8K SPI and I2C config in DTS
Align the Armada-8040-db and Armada-7040-db SPI and I2C
DTS settings with latest DB settings:
- 8040-db: disable i2c0 and spi0 on AP (MPPs are reserved for SDIO)
- 8040-db: disable cps_i2c0 on CP1
- 8040-db: enable spi1 on CP1 (the new location of the boot flash)
  The spi1 on CP1 is aliased as spi0 since this is the way
  the driver enumerates it.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2016-12-12 09:04:52 +01:00
Masahiro Yamada
6c498835af ARM: uniphier: remove BLK select
This is a user configurable option, but "select BLK" forces users to
enable it.

Even with this commit, BLK is still enabled by "default y if DM_MMC"
for UniPhier SoCs; the difference is users can disable it if they
do not need it.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-12-11 17:55:13 +09:00
Masahiro Yamada
cd62214d98 ARM: dts: uniphier: sync Device Tree with Linux
Sync with the latest kernel.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-12-11 17:55:01 +09:00
Tom Rini
170397f17d imgtec: Update MAINTAINERS for more config files
Cover all of the boston and malta variations.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-12-09 15:00:04 -05:00
Jyri Sarha
8c17cbdf8a arm: am33xx: Initialize EMIF REG_PR_OLD_COUNT for BBB and am335x-evm
Initialize EMIF OCP_CONFIG registers REG_COS_COUNT_1, REG_COS_COUNT_2,
and REG_PR_OLD_COUNT field for Beaglebone-Black and am335x-evm. With
the default values LCDC suffers from DMA FIFO underflows and frame
synchronization lost errors. The initialization values are the highest
that work flawlessly when heavy memory load is generated by CPU. 32bpp
colors were used in the test. On BBB the video mode used 110MHz pixel
clock. The mode supported by the panel of am335x-evm uses 30MHz pixel
clock.

Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-09 15:00:03 -05:00
Christian Riesch
177f14da7f calimain: Update maintainers and their email addresses
Signed-off-by: Christian Riesch <christian@riesch.at>
Cc: Manfred Rudigier <manfred.rudigier@omicronenergy.com>
Cc: Christoph Rüdisser <christoph.ruedisser@omicronenergy.com>
2016-12-09 15:00:02 -05:00
Masahiro Yamada
2411e0fbd9 ARM: uniphier: disable CONFIG_ARCH_FIXUP_FDT_MEMORY
Do not overwrite the memory nodes in the kernel DT where some parts
of the memory region might be carved out.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-12-10 01:42:51 +09:00
Masahiro Yamada
996fcdadba ARM: uniphier: remove unneeded parentheses
Just a cosmetic cleanup.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-12-10 01:42:51 +09:00
Masahiro Yamada
82ff6c392f ARM: uniphier: remove unneeded initializer
This will be used to store the return value of readl().

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-12-10 01:42:51 +09:00
Tom Rini
3c643fb01b travis-ci: Switch to building QEMU
First, there are a number of features in newer QEMU that will allow us
to test a wider range of platforms, so we want to use at least v2.8.0.
Second, making use of a PPA for QEMU fails from time to time.  So we
change to checking out and building a copy of QEMU when we know that we
are going to use test.py and need QEMU to be installed.  This adds
around 4 minutes per test.py job that we run.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-12-09 08:40:23 -05:00
Michal Simek
ebe0f53f48 tools: mkimage: Use fstat instead of stat to avoid malicious hacks
The patch is fixing:
"tools: mkimage: Check if file is regular file"
(sha1: 56c7e80155)
which contains two issues reported by Coverity
Unchecked return value from stat and incorrect calling sequence where
attack can happen between calling stat and fopen.
Using pair in opposite order (fopen and fstat) is fixing this issue
because fstat is using the same file descriptor (FILE *).

Also fixing issue with:
"tools: mkimage: Add support for initialization table for Zynq and
ZynqMP" (sha1: 3b6460809c)
where file wasn't checked that it is regular file.

Reported-by: Coverity (CID: 154711, 154712)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-09 08:40:23 -05:00
Fabien Parent
963ed6f323 davinci: omapl138_lcdk: boot from zImage
Stop booting legacy uImage and now boot zImage.

Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-09 08:40:23 -05:00
Andrew F. Davis
1c9021d622 defconfigs: am57xx_hs_evm: Add default OPTEE load address
Currently we let U-Boot find a spot at the end of DRAM at runtime, this
forces us to build an OPTEE image based on the size of DRAM for an EVM.
Add a default address that works across all current AM57xx EVMs.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-09 08:40:22 -05:00
Andrew F. Davis
e3e3c633b6 defconfigs: dra7xx_hs_evm: Add default OPTEE load address
Currently we let U-Boot find a spot at the end of DRAM at runtime, this
forces us to build an OPTEE image based on the size of DRAM for an EVM.
Add a default address that works across all current DRA7xx EVMs.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-09 08:40:21 -05:00
Fabien Parent
2b2cab24ac davinci: omapl138_lcdk: fix bad NAND ECC config
The configuration used to error correction was not in line with what
linux and the ROM code is using. Fix it by using the correct
configuration. Now u-boot and the SPL are able to read correctly
anything written by them.

Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-09 08:40:20 -05:00
Fabien Parent
c0c10449cf davinci: omapl138_lcdk: increase u-boot load size
A size of 0x200 seems way too short for u-boot. Increase the size
to 512k.

Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-09 08:40:19 -05:00
Yehuda Yitschak
e5f96a872b cmd: pci: add option to parse and display BAR information
Currently the PCI command only allows to see the BAR register
values but not the size and actual base address.
This little extension parses the BAR registers and displays
the base, size and type of each BAR.

Signed-off-by: Yehuda Yitschak <yehuday@marvell.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-12-09 08:40:18 -05:00
Simon Glass
f831b8e4a4 spl: sandbox: Drop spl_board_announce_boot_device()
This function is not used anymore. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-12-09 08:40:18 -05:00
Simon Glass
dd38045dce spl: uniphier: Drop spl_board_announce_boot_device()
This function is not used anymore. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-12-09 08:40:17 -05:00
Simon Glass
40ecf52495 spl: sunxi: Drop spl_board_announce_boot_device()
This function is not used anymore. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-12-09 08:40:16 -05:00
Simon Glass
2acf35dbf7 spl: Drop announce_boot_device()
This task can be handled by inline code now. Drop this function.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-12-09 08:40:15 -05:00
Simon Glass
29d357d7bf spl: Pass the loader into spl_load_image()
Rather than have this function figure out the correct loader again, pass
it in as a parameter.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-12-09 08:40:15 -05:00
Simon Glass
540bfe7daa spl: Move the loading code into its own function
Create a boot_from_devices() function to handle trying each device. This
helps to reduce the size of the already-large board_init_r() function.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-12-09 08:40:14 -05:00