Compute the DDR size from DDR controller register (mstr and addrmap)
in U-Boot proper as the DDR information are useful only for SPL
but not for U-Boot proper, for example with TFABOOT.
This patch simplify U-Boot DT when several DDR size are supported
and support of next SOC in STM32MP family.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The IPCC mailbox is only used for communication with M4 firmware but
it is not used in the stm32 remoteproc driver; it was planed but the
support of this mailbox in remoteproc for STM32MP15x is dropped.
So the associated drivers and config CONFIG_STM32_IPCC can be
deactivated to reduce the U-Boot size; the CONFIG_DM_MAILBOX can be
also deactivated as the mailbox UCLASS is no more used.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Enable an existing simple framebuffer node in the Linux kernel device
tree and the add the associated reserved memory node to preserved the
resources (clock, memory) used by the stm32 video driver to display
the splashscreen = background in exlinux.conf file.
These resources will be released by the Linux driver only when the
associated driver is ready to avoid transition issues during the Linux
kernel initialization between U-Boot splash screen and the final display.
See Linux documentation for details:
Documentation/devicetree/bindings/display/simple-framebuffer.yaml
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Align the framebuffer size on MMU_SECTION_SIZE in kernel, = max 2MB for
LPAE for armV7, to avoid issue with the simple frame buffer activation,
when U-Boot add a reserved memory in the kernel device tree to preserve
the splash screen until Linux driver initialization.
See Linux documentation for details:
Documentation/devicetree/bindings/display/simple-framebuffer.yaml
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add a new function to activate an existing simple frame buffer node
and add the associated reserved memory, with no-map properties.
This device tree update is only done when the video device is active
and the video buffer is used.
This patch uses '#if CONFIG_IS_ENABLED(DM_VIDEO)' because
gd->video_bottom and gd->video_top are only defined when CONFIG_DM_VIDEO
is activated.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add the helper function video_is_active() to test if one video device
is active.
This function can be used in board code to execute operation
only when the display is probed / really used.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Rename the function named lcd_dt_simplefb* to fdt_simplefb* to be aligned
with the associated file name fdt_simplefb.h/fdt_simplefb.c
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Rename the file lcd_simplefb.c to fdt_simplefb.c to be aligned
with the configuration name and with the associated include file
./include/fdt_simplefb.h
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This converts the following to Kconfig:
CONFIG_LCD_DT_SIMPLEFB
This patch also renames this config to CONFIG_FDT_SIMPLEFB as the code in
common/lcd_simplefb.c support CONFIG_LCD and CONFIG_VIDEO.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Remove the DDR interactive command tuning, as the support of a predefined
DDR PHY tuning is removed for STM32MP1 driver in SPL and in TF-A
and the result of this tuning will be never used.
Moreover this SW tuning procedure can failed on some hardware
configuration (to many BIST errors and no convergence); it will be no
more supported in the next delivery of the DDR utilities included in
the CubeMX tool of STMicroelectronics.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The support of a predefined DDR PHY tuning result is removed for
STM32MP1 driver because it is not needed at the supported frequency
when built-in calibration is executed.
The calibration parameters were provided in the device tree by the
optional node "st,phy-cal", activated in ddr helper file by the
compilation flag DDR_PHY_CAL_SKIP and filled with values generated
by the CubeMX DDR utilities.
This patch
- updates the binding file to remove "st,phy-cal" support
- updates the device trees and remove the associated defines
- simplifies the STM32MP1 DDR driver and remove the support of
the optional parameter "st,phy-cal"
After this patch, the built-in calibration is always executed
and the calibration registers are moved in the phy dynamic part;
that allows manual tests.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add the read data eye training = training for optimal read valid placement
(RVTRN) when the built-in calibration is executed for LPDDR2 and LPDDR3.
This training is supported on the PUBL integrated in the STM32MP15x
DDR subsystem and it is not required for DDR3.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The uSD level translator on DHSOM and Avenger96 are optional, however it
is possible to auto-detect it. This is done by setting SD CMD line high,
and then testing whether signal level on CK line matches the signal level
on CKIN line. If so, the uSD level translator is present, otherwise it is
not populated.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add support for testing whether bus voltage level translator is present
and operational. This is useful on systems where the bus voltage level
translator is optional, as the translator can be auto-detected by the
driver and the feedback clock functionality can be disabled if it is
not present.
The translator test sets CMD high to avoid interfering with a card, and
then verifies whether signal set on CK is detected on CKIN. If the signal
is detected, translator is present, otherwise the CKIN feedback clock are
disabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Yann Gautier <yann.gautier@foss.st.com>
Enable KSZ9x01 PHY driver in DHCOR common configuration, since the
AV96 board has this PHY populated on the PCB.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The ethernet PHY must be reset on AV96, however DWMAC currently does
not support the MDIO-bus PHY GPIO reset bindings and the ethernet MAC
PHY reset property is going away on next DT sync. Add PHY specific
reset bindings to trigger the PHY reset and fix sporadic ethernet
malfunctions, until the next DT sync.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The variables retaining the strap values have to be initialized, always,
make it so. Moreover, free the requested GPIO list at the end to avoid
wasting memory.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The Micrel PHYs on known DHSOM based boards take a while to come out
of reset, increase the auto-negotiation timeout to prevent it from
timing out in case the ethernet is used right after the board was
reset.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add script to read U-Boot from SD card and write it to matching
locations in the SPI NOR, thus making the SPI NOR bootable. The
script erases the entire SPI NOR, including U-Boot environment,
to make sure the installation is clean. To retain environment
from current running U-Boot, run 'saveenv' after running the
'update_sf' script.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The USB hub on STM32MP1 DHCOM boards needs to wait a bit longer until
the USB Vbus is stable. Increase the USB power-good delay to 1 s.
This adds default-undefined STM32MP_BOARD_EXTRA_ENV variable into
stm32mp15_common.h to reduce duplication in board-specific config
files adding custom environment.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The common emulation Makefile has a dependency on a non-existent
qemu_capsule.o when building with support for capsule update enabled
(CONFIG_EFI_RUNTIME_UPDATE_CAPSULE=y).
The code which was in qemu_capsule.c has been completely moved to
lib/efi_loader/efi_capsule.c by commit 7a6fb28c8e ("efi_loader: capsule:
add back efi_get_public_key_data()").
Remove the false dependency.
This fixes the following build error:
make[1]: *** No rule to make target 'board/emulation/common/qemu_capsule.o', needed by 'board/emulation/common/built-in.o'. Stop.
Fixes: commit 47a25e81d3 ("Revert "efi_capsule: Move signature from DTB to .rodata"")
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Cc: Simon Glass <sjg@chromium.org>
Add an entry in maintainers for fastboot. It is starting off orphaned, but
hopefully someone can pick it up.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Lukasz has not been very responsive in reviewing clock patches. Add
myself as a maintainer.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Various driver model enhancements
Fix up some missing unit tests with pytest
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmGkFroRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrea7QQgAjSlchhsXmUoBjl8rmpBJryTzeipdp/bw
FOc5xOu4y9PJCXrO5EMk0qAngUpmzZWdMV67iYnDT8b4CJeuFili9tbuvkVNGeXs
xpx0VVAb443XdY4QLFHl0w/WrUp6yPTTaT8GI3jpUoHXiWelu8rn8azTjZFZhgtz
O/7ZfKJy2bWKICAoi9KP17IRnK9IqORgIh1ADJPkmaBCBeOE0TqVpUlSdVwSkJHR
MtthfqQ57O6r+zZjw9wG/V6TRYjvQRcXDrOMk7myYaK4Hc8s9WHjdgDDmxvNX29J
Ziix00Lv8EA3sT+bwE88XQYh6NYWcsAJbi676juO4FF871+qJsiTOg==
=dyds
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-28nov21' of https://source.denx.de/u-boot/custodians/u-boot-dm into next
SPI flash documentation and tidy-ups
Various driver model enhancements
Fix up some missing unit tests with pytest
At present an Exception is raised if a command fails. This is a very broad
class and makes it difficult for callers to catch the error without also
catching other things, like programming bugs.
Change it to ValueError to make this easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the collection function used by pytest is quite strict on the
naming of the functions it detects. In particular it requires the name of
the test to be repeated in the function name.
This is not enforced anywhere else, but instead the tests are silently
omitted from the pytest run. This affects a few dozen tests.
The rule does not seem to have any particular purpose. Relax it, so that
all tests that use the UNIT_TEST() macro will run, regardless of the name
of the test function.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the hexdump tests are disabled in sandbox_flattree. This is
good, because they do not pass. Enable the required Kconfig so that they
will, when enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a function that returns the number of devices in a uclass. This can be
helpful in sizing an array that needs to hold a list of them.
Signed-off-by: Simon Glass <sjg@chromium.org>
In some cases it is useful to search just by a partial name, such as
when looking for a sibling device that has a common name substring. Add
helper functions to handle these requirements.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we support reading a string list a string at a time. Apart
from being inefficient, this makes it impossible to separate reading of
the devicetree into the of_to_plat() method where it belongs, since any
code which needs access to the string must read it from the devicetree.
Add a function which returns the string property as an array of pointers
to the strings, which is easily used by clients.
Signed-off-by: Simon Glass <sjg@chromium.org>
The details for of_property_read_string_helper() and
ofnode_read_string_index() are a little inaccurate. Fix up the comments to
avoid confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
This method is currently called after the platform data has been freed.
But the pre_unbind() method may wish to access this, e.g. to free some
data structures stored there.
Split the unbinding of devices into two pieces, as is done with removal.
This corrects the problem.
Also tidy a code-style issue in device_remove() while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
These functions currently lack tests so add some. The error handling
differs betwee livetree and flattree at present, so only check the error
codes with livetree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Before relocation there is generally not as much available memory and not
that much console output. At present the console-output buffer is the same
side before and after relocation. Add a separate Kconfig option to remove
this limitation.
Signed-off-by: Simon Glass <sjg@chromium.org>
When ext is NULL we cannot dereference it. Update the code flow to avoid
this, so that layout_mbr_partitions() can be used with partition tables
that do not include an extended partition.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this command considers the partitions to be identical if the
start and size are smaller than expected. It should check that they are
the same. Fix this and tidy up the code style a little.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
At present the MMC uclass assumes that the only child it can have is a
block device. Update this so we can add a bootmethod too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Provide a way for sandbox MMC to present data from a backing file. This
allows a filesystem to be created on the host and easily served via an
emulated mmc device.
Signed-off-by: Simon Glass <sjg@chromium.org>
