Now that the musb-new driver has a Kconfig, we can move Kconfig options to
enable controllers to it, so that it's easier in e.g. menuconfig.
In addition, this allows declaring support for USB_MUSB_HOST/GADGET in
defconfigs instead of the USB_MUSB_SUNXI controller, that will get selected
automatically when needed.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Having MUSB_HOST and MUSB_GADGET in Kconfig allows more flexibility with regard
to what Kconfig options to enable, such as USB_STORAGE or USB_KEYBOARD.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
USB-related options are usually prefixed with CONFIG_USB and platform-specific
adaptation for the MUSB controller already have a CONFIG_USB_MUSB prefix, so
this switches all MUSB-related options to a CONFIG_USB_MUSB prefix, for
consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
There is no particular reason why the USB Kconfig option should be specific to
host mode. In prevision of adding MUSB host and gadget to Kconfig, this moves
the title and help message of the USB Kconfig option to a more generic format.
Adding comments to the usb Kconfig allows for a better separation and more
readability in generated configs and in menuconfig.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
The USB_ARCH_HAS_HCD currently serves no purpose and adds some confusion to the
required Kconfig options that are required to have USB support.
Dropping it makes things easier and doesn't break anything, since it was unused
anyways.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This patch makes the dwc2 controller like ehci / ohci / xhci controllers
by calling the board_usb_init() function from usb_lowlevel_init.
This can then be implemented by specific platforms to initialise
their USB hardware (phys / clocks etc).
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
This patch replaces not existing addr_uboot environment variable by
loadaddr at get_uboot_net and burn_uboot_xxx commands. Otherwise these
commands are broken.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Define base address of both usb xhci controllers in lsch3 config
in the format (IMMR + offset) for LS2085A
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Define CONFIG_SYS_CACHELINE_SIZE for LS2085A which is required by
USB XHCI stack for alignment
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
By default the bstopre value has been set to 0x100, used to be 1/4
value of refint. Modern DDR has increased the refresh time. Adjust
to 1/4 of refresh interval dynamically. Individual board can still
override this value in board ddr file, or to use auto-precharge.
Signed-off-by: York Sun <yorksun@freescale.com>
HW coherency won't work properly for CAAM write transactions
if AWCACHE is left to default (POR) value - 4'b0001.
It has to be programmed to 4'b0010.
For platforms that have HW coherency support:
-PPC-based: the update has no effect; CAAM coherency already works
due to the IOMMU (PAMU) driver setting the correct memory coherency
attributes
-ARM-based: the update fixes cache coherency issues,
since IOMMU (SMMU) driver is not programmed to behave similar to PAMU
Fixes: b9eebfade9 ("fsl_sec: Add hardware accelerated SHA256 and SHA1")
Signed-off-by: Horia Geantă <horia.geanta@freescale.com>
Reviewed-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Acked-by: Ruchika Gupta<ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Use fdt_setprop_u32() instead of fdt_setprop().
Fixes: 0181937fa3 ("crypto/fsl: Add fixup for crypto node")
Signed-off-by: Horia Geantă <horia.geanta@freescale.com>
Reviewed-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Acked-by: Ruchika Gupta<ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The patch will initialize PCIe controller on EP mode
1. Setup bar:
bar0 32bit 4K for specific configuration
bar1 32bit 8K for MSIX
bar2 64bit 4K for descriptor of memory
bar4 64bit 1M for DMA memory test
2. Setup iATU:
iATU inbound 0-3 to map bar transaction to memory address
started at CONFIG_SYS_PCI_EP_MEMORY_BASE
iATU outbound 0 to map 4G memory space
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
PCIe extends device's configuration space to 4k and provides
extended capability. The patch adds function to find them.
The code is ported from Linux PCIe driver.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <yorksun@freescale.com>
MC firware version 8.0.0 contains new command flags. This patch
contains modifications in FLIB files to support the new command flags.
Signed-off-by: Itai Katz <itai.katz@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The sampling of the oscillator can be done in multiple modes for
generating the entropy value. By default, this is set to von
Neumann. This patch changes the sampling to raw data, since it
has been discovered that the generated entropy has a better
'quality'.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Acked-by: Ruchika Gupta<ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The entropy delay (the length in system clocks of each
entropy sample) for the RNG4 block of CAAM is dependent
on the frequency of the SoC. By elaborate methods, it
has been determined that a good starting value for all
platforms integrating the CAAM IP is 3200. Using a
higher value has additional benefit of speeding up
the process of instantiating the RNG, since the entropy
delay will be increased and instantiation of the RNG
state handles will be reattempted by the driver. If the
starting value is low, for certain platforms, this can
lead to a quite lengthy process.
This patch changes the starting value of the length of
the entropy sample to 3200 system clocks.
In addition to this change, the attempted entropy delay
values are now printed on the console upon initialization
of the RNG block.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Acked-by: Ruchika Gupta<ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The rtfrqmax & rtfrqmin set the bounds of the expected frequency of the
oscillator, when SEC runs at its maximum frequency. For certain platforms
(f.i. T2080), the oscillator is very fast and thus if the SEC runs at
a lower than normal frequency, the ring oscillator is incorrectly detected
as being out of bounds.
This patch effectively disables the maximum frequency check, by setting a
high enough maximum allowable frequency for the oscillator. The reasoning
behind this is that usually a broken oscillator will run too slow
(i.e. not run at all) rather than run too fast.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Acked-by: Ruchika Gupta<ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
To improve eTSEC performance on LS1021A Rev2.0,
snooping of all transmit frames from memory and
all transmit BD memory accesses in enabled.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
On LS1021A Rev2.0, OCRAM's security level needs to be changed to
non-secure access for SD boot. This patch will allow OCRAM
access permission as R/W in SPL.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Bootrom will put cpus into WFE state when boot cpu release cpus, so
target cpu cannot correctly go to spin state.
Add 'sev' to wakeup non-boot cpu that hold on bootrom space, let target
cpu can fall into u-boot spin table.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Program the external regulator to switch off voltage in deep sleep.
Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Enable bootscript support in secure boot for establishing
chain of trust on LS1021atwr.
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
strncpy is safer than strcpy, use it to instead of strcpy.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
when using printf, the parameter type need to be compatible
type, so transform them to compatible type
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For ls1021a, Reserve secure code in to memory in case OCRAM
is needed by other usage.
Signed-off-by: Zhuoyu Zhang <Zhuoyu.Zhang@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Fix:
undefined reference to `spi_flash_free'
undefined reference to `spi_flash_probe'
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Stefan Roese <sr@denx.de>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Acked-by: Stefan Roese <sr@denx.de>
1. Define two structures mx6ul_iomux_ddr_regs and mx6ul_iomux_grp_regs.
2. Add a new function mx6ul_dram_iocfg to configure dram io.
3. Refactor MMDC1 macro, discard "#ifdef CONFIG_MX6SX". Since
only mmdc0 channel exists on i.MX6SX/UL, redefine MMDC1 macro support
runtime check, but not hardcoding #ifdef macros.
4. Introduce mx6ul-ddr.h, which includes the register address for DRAM
IO configuration.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
1.Update WDOG settings.
2.No need to gate/ungate all PFDs for i.MX6UL.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
i.MX6UL features an Cortex-A7 core, it does not have PL310 as other i.MX6
chips. To Cortex-A7 core, If D-Cache is enabled, L2 Cache is enabled.
There is on specific switch for on/off L2 Cache, so default select
SYS_L2CACHE_OFF.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
1. Add enet, uart, i2c, ipg clock support for i.MX6UL.
2. Correct get_periph_clk, it should account for
MXC_CCM_CBCDR_PERIPH_CLK2_PODF_MASK.
3. Refactor get_mmdc_ch0_clk to make all i.MX6 share one function,
but not use 'ifdef'.
4. Use CONFIG_FSL_QSPI for enable_qspi_clk, but not #ifdef CONFIG_MX6SX.
5. Use CONFIG_PCIE_IMX for pcie clock settings, use CONFIG_CMD_SATA for
sata clock settings. In this way, we not need "#if defined(CONFIG_MX6Q)
|| defined....", only need one CONFIG_PCIE_IMX in header file.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Since i.MX6UL use A7 core, but not A9 core, we do not need
the erratas for i.MX6UL.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Since i.MX6UL's cache line size is 64bytes, need to
define the macro CONFIG_SYS_CACHELINE_SIZE to 64 for i.MX6UL.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
1. Update imx register base address for i.MX6UL.
2. Remove duplicated MXS_APBH/GPMI/BCH_BASE.
3. Remove #ifdef for register addresses that equal to
"AIPS2_OFF_BASE_ADDR + 0x34000" for different chips.
4. According fuse map, complete fuse_bank4_regs.
5. Move AIPS3_ARB_BASE_ADDR and AIPS3_ARB_END_ADDR out of #ifdef CONFIG_MX6SX,
because we can use runtime check
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Add i.MX6UL pins IOMUX file which defines the IOMUX settings for choose.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Add MXC_CPU_MX6UL for i.MX6UL CPU type which is got at runtime from
DIGPROG register. But the value has been occupied by MXC_CPU_MX6D which
is not real id from DIGPROG register, so change i.MX6D to value 0x67 which
was not occupied.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
