Commit graph

11046 commits

Author SHA1 Message Date
Derald D. Woods
4b37928d35 ARM: dts: omap3-beagle{-xm}: Enable DM and devicetree for BeagleBoard
This commit updates the configuration files needed to support OF_CONTROL
on the OMAP3 BeagleBoard(s).
2018-01-19 15:49:28 -05:00
Lokesh Vutla
b4185e4fef ARM: dts: am574x-idk: Add initial support
Add initial dts support for am574x-idk

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-01-19 15:49:27 -05:00
Lokesh Vutla
443b0df361 board: ti: am574x-idk: Update pinmux using latest PMT
Update the board pinmux for AM574x-IDK board using latest PMT[1] and the
board files named am574x_idk_v1p3b_sr2p0 that were auto generated on
13th October, 2017 by "Ahmad Rashed <a-rashed@ti.com>".

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-01-19 15:49:27 -05:00
Lokesh Vutla
7b16de8595 board: ti: am574x-idk: Add ddr data support
AM574x-idk has the following DDR parts attached:
EMIF1: MT41K256M16HA (1GB with ECC)
EMIF2: MT41K256M16HA (1GB without ECC)

Enabling 2GB DDR without interleaving between EMIFs. And
enabling ECC on EMIF1.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Krunal Bhargav <k-bhargav@ti.com>
2018-01-19 15:49:27 -05:00
Lokesh Vutla
10f430f3f1 board: ti: am574x-idk: Add hw data support
Update prcm, voltages and pinmux support for am574x-idk.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-01-19 15:49:26 -05:00
Lokesh Vutla
9646b95f64 board: ti: am574x-idk: Add epprom support
am574x-idk is a board based on TI's am574 processor
Add eeprom support.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-01-19 15:49:26 -05:00
Lokesh Vutla
941f2fcc5b arm: dra762: Add support for device package identification
DRA762 comes in two packages:
- ABZ: Pin compatible package with DRA742 with DDR@1333MHz
- ACD: High performance(OPP_PLUS) package with new IPs

Both the above packages uses the same IDCODE hence needs to
differentiate using package information in DIE_ID_2.
Add support for the same. Also update clock, ddr, emif information.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-01-19 15:49:26 -05:00
Lokesh Vutla
f1627bdc19 board: ti: k2g: Make ddr3* declarations as static
All ddr3_emif declarations are not used outside ddr3_k2g.c
file. So make all of them as static.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-01-19 15:49:25 -05:00
Tomi Valkeinen
8d0dcbf212 board: ti: dra76: mux wakeup2 as gpio1_2
gpio1_2 is used for HPD interrupt with DRA76's DVI add-on board, so mux
the pin as gpio and PIN_INPUT.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2018-01-19 15:49:24 -05:00
Rex Chang
4849d95407 board: ti: K2G FC SoC 1GHz and DDR3 1066 MT/s support
Added support for K2G EVM with FlipChip SoC of which
ARM/DDR3 runs at 1GHz/1066 MT/s. The patch is also
backward compatible with old revision EVM and EVM
with WireBond SoC. Their ARM/DDR3 run at 600MHz/800 MT/s.

The new SoC supports 2 different speeds at 1GHz and 600MHz.
Modyfied the CPU Name to show which SoC is used in the EVM.
Modified the DDR3 configuration to reflect New SoC supports
2 different CPU and DDR3 speeds, 1GHz/1066MT and 600MHz/800MT.

Added new inline function board_it_k2g_g1() for the new FlipChip 1GHz,
and set the u-boot env variable board_name accordingly.

Modified findfdt script in u-boot environment variable to include new k2g board type.

Signed-off-by: Rex Chang <rchang@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-01-19 15:49:24 -05:00
Vignesh R
e36edcec0a board: ti: dra7xx: Select MCAN instead of DCAN on DRA76 EVM
MCAN can be accessed via DCAN1 or DCAN2. Determining which DCAN instance
to use if any at all is done through
CTRL_CORE_CONTROL_SPARE_RW.SEL_ALT_MCAN. Since general pinmuxing is
handled in U-boot. Handle this additional pinmuxing requirement in U-boot
to ensure that MCAN is used by default via the DCAN1 pins.

Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
[fcooper@ti.com: Update commit message and use DCAN1 not DCAN2 for MCAN]
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2018-01-19 15:49:23 -05:00
Tom Rini
086ebcd40e Merge git://git.denx.de/u-boot-fsl-qoriq 2018-01-17 13:48:35 -05:00
Tom Rini
1f0ce3259e freescale: Ensure common commands are not included in SPL binary
Both the "qixis_reset" and esbc_validate" commands can only be used in
full U-Boot so do not build them in SPL.  As part of this rework the
qixis code to declare things as static and make use of __weak for
function aliases.

Cc; York Sun <york.sun@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-17 10:30:45 -08:00
Andre Przywara
8837af154c sunxi: arm64: correct usage of DT node address in FIT generation
The DT spec demands a unit-address in a node name to match the "reg"
property in that node. Newer dtc versions will throw warnings if this is
not the case.
Adjust the FIT build script for 64-bit Allwinner boards to remove the
bogus addresses from the node names and avoid the warnings.
This avoids a warning with recent versions of the dtc tool.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2018-01-15 18:29:21 -07:00
Tom Rini
8e9801c283 Merge git://git.denx.de/u-boot-imx 2018-01-15 16:44:18 -05:00
Jorge Ramirez-Ortiz
9337dfb434 db410c: use the device tree parsed by the lk loader.
We dont need to keep copies of the properties that we are going to
fixup since we will be using the dtb provided by the firmware.

Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
2018-01-15 16:29:03 -05:00
Jorge Ramirez-Ortiz
0689eb7470 db410c: replace reset driver with psci
this should be the norm for armv8 platforms.

Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
2018-01-15 16:29:03 -05:00
Jorge Ramirez-Ortiz
e2beb872f7 db410c: update wlan and bt mac addresses from firmware
The firmware that runs before u-boot modifies u-boot's device tree
adding the local-mac-address and local-bd-address properties for the
compatibles "qcom,wcnss-bt" and "qcom,wcnss-wlan".

This commit reads that firmware, retrieves the properties and fixups
the device tree that is passed to the kernel before booting.

Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
2018-01-15 16:29:03 -05:00
Jorge Ramirez-Ortiz
100fb0bd99 db820c: stop autoboot when vol- pressed
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
2018-01-15 16:29:02 -05:00
Jorge Ramirez-Ortiz
4b684a6b82 db820c: add qualcomm dragonboard 820C support
This commit adds support for 96Boards Dragonboard820C.

The board is based on APQ8086 Qualcomm Soc, complying with the
96Boards specification.

Features
 - 4x Kyro CPU (64 bit) up to 2.15GHz
 - USB2.0
 - USB3.0
 - ISP
 - Qualcomm Hexagon DSP
 - SD 3.0 (UHS-I)
 - UFS 2.0
 - Qualcomm Adreno 530 GPU
 - GPS
 - BT 4.2
 - Wi-Fi 2.4GHz, 5GHz (802.11ac)
 - PCIe 2.0
 - MIPI-CSI, MIPI-DSI
 - I2S

U-Boot boots chained from LK (LK implements the fastboot protocol) in
64-bit mode.

For detailed build instructions see readme.txt in the board directory.

Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
2018-01-15 16:29:02 -05:00
Tom Rini
68ae7772af arm: ls1021atwr: Rework local commands to not be included in SPL
Move some of the code for the "lane_bank" and "cpld" code local
commands so that they are not built for SPL as they can only be
used in full U-Boot.  This means we can mark a few functions as
static as well now.

Cc: Alison Wang <alison.wang@freescale.com>
Cc: Sumit Garg <sumit.garg@nxp.com>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
Tested-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-15 12:44:24 -08:00
Tom Rini
3a72a0efcc powerpc: P1010RDB: Rework local command to not be included in SPL
Add a CONFIG_SPL_BUILD guard around the code for the "mux" command so
it is not included in SPL.

Cc: Qiang Zhao <qiang.zhao@nxp.com>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Qiang Zhao <qiang.zhao@nxp.com>
2018-01-15 12:44:24 -08:00
Priyanka Jain
da28a03ed4 board/ls2081ard: Correct code to get QMAP value in checkboard
QMAP value contains information about QSPI chip-selects. These bits
are used to display information of boot device in checkboard()
function.

QMAP value is stored in most significant 3-bits of 8-bit register
brdcfg[0] in Qixis, this patch corrects code to get QMAP bits using
below logic:
	(brdcfg[0] >> 5) & 0x7

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-15 12:44:23 -08:00
Priyanka Jain
f436fbfeb1 board/ls2081ardb: Update board related prints
Remove Board Arch print as its value is always constant '1' and does
not contain any important information to display during boot.
Add print to display Board FPGA version.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-15 12:44:23 -08:00
Sumit Garg
86c773fe83 configs: SECURE_BOOT: Enable CONFIG_CMD_EXT4_WRITE
As part of chain of trust with confidentiality along with distro
boot, linux kernel image needs to be stored in encrypted form on
ext4 boot partition. So enable CONFIG_CMD_EXT4_WRITE in case of
Secure boot on ARM based platforms.

Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-15 12:44:23 -08:00
Bhaskar Upadhaya
b0ce187b1f board: ls1012a: LS1012A-2G5RDB board support
LS1012A-2G5RDB belongs to LS1012A family with features 2 2.5G SGMII
PFE MAC, SATA, USB 2.0/3.0, WiFi DDR, eMMC, QuadSPI, UART.

Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-15 11:56:33 -08:00
Christopher Spinrath
dbeaa1d131 ARM: imx: cm_fx6: export board and soc info to env
Like many other i.MX6 based boards, there are multiple variants of
the cm-fx6 module featuring different SoC variants. Furthermore, the
module can be paired with multiple baseboards.

At the same time modern distribution like Fedora require U-Boot to
select a proper devicetree which depends on the SoC variant and the
baseboard.

Thus, export the SoC variant and the actual board to the environment
following the conventions of other i.MX6 devices (e.g. the NXP boards)
such that the environment can select a devicetree file to load.

For now, we only know for sure that the cm-fx6 module and the SB-fx6m
baseboard amount to a Utilite Computer variant (depending on the SoC).
Further combinations may be added in the future; e.g. CompuLab's
evaluation board once someone can verify the identification string
stored in its eeprom.

Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2018-01-12 14:28:04 +01:00
Fabio Estevam
0f194018f2 mx6memcal: spl: Disambiguate the error message
Currently mmdc_do_dqs_calibration() and mmdc_do_write_level_calibration()
show the same error message, which is confusing for debugging.

Disambiguate the mmdc_do_dqs_calibration() error message.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-12 14:28:04 +01:00
Fabio Estevam
941fcabfa7 mx6memcal: spl: Also take i.MX6ULL into account
i.MX6ULL also does not support 64-bit DDR bus, so add it to the
check logic.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-12 14:28:04 +01:00
Fabio Estevam
db00e921fd mx6memcal: Fix the UART ports for mx6sabresd/auto boards
mx6sabresd board uses the following pins for console:

PAD_CSI0_DAT10__UART1_TX_DATA
PAD_CSI0_DAT11__UART1_RX_DATA

,so put it in the same config option as wandboard.

mx6sabreauto board uses the following pins for console:

PAD_KEY_COL0__UART4_TX_DATA
PAD_KEY_ROW0__UART4_RX_DATA

So do not mention sabreauto board as part of the UART1_SD3_DAT6_7 option.

The config option for sabreauto can be added later when needed.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-12 14:28:04 +01:00
Tom Rini
64c7abf023 toradex: imx6: Rework PF0100 fuse programming commands to not be in SPL
The code for programming the OTP fuses on the PMIC PF0100 can only be
used in full U-Boot, so do not build / link it into SPL.

Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Max Krummenacher <max.krummenacher@toradex.com>
2018-01-12 14:28:04 +01:00
Tom Rini
bf52330a50 imx: ventana: Rework CONFIG_CMD_GSC code to not be included in SPL
The command can only be used from full U-Boot, so do not build it into
SPL.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-12 14:28:04 +01:00
Tom Rini
c10b1c43fd imx: ventana: Rework CONFIG_CMD_EECONFIG code to not be included in SPL
The command can only be used from full U-Boot, so do not build it into
SPL.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-12 14:28:04 +01:00
Peng Fan
e80f9e1a37 imx: mx6sxsabresd: config wdog pinmux
Because kernel set WDOG_B mux before pad with the common pinctrl
framwork now and wdog reset will be triggered once set WDOG_B mux
with default pad setting, we set pad setting here to workaround this.
Since imx_iomux_v3_setup_pad also set mux before pad setting, we set
as GPIO mux firstly here to workaround it.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-12 14:28:04 +01:00
Peng Fan
5dfc9d3766 imx: mx6sxsabresd: Enable DM driver
Enable I2C/MMC/GPIO/REGUALTOR/PMIC/USB DM drivers.
There are some dependency, such as when DM MMC enabled, USB compile error.
Also the i.MX I2C MMC DM driver does not support legacy GPIO interface.
So enable them all together.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-12 14:28:04 +01:00
Peng Fan
f8e450a7f6 board: freescale: common: add pfuze dm code
Add pfuze dm code, this code could be enabled with CONFIG_DM_PMIC_PFUZE100.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-12 14:28:04 +01:00
Stefano Babic
fb8cac9366 mx6: Support SKS-Kinkel sksimx6 Board
Board  has 1GB RAM and boots from SD Card

U-Boot SPL 2018.01-rc3-00005-ga1898b8 (Jan 02 2018 - 13:48:54)
BT_FUSE_SEL already fused, will do nothing
Trying to boot from MMC1

U-Boot 2018.01-rc3-00005-ga1898b8 (Jan 02 2018 - 13:48:54 +0100)

CPU:   Freescale i.MX6DL rev1.2 996 MHz (running at 792 MHz)
CPU:   Commercial temperature grade (0C to 95C) at 40C
Reset cause: POR
I2C:   ready
DRAM:  1 GiB
MMC:   FSL_SDHC: 0
In:    serial
Out:   serial
Err:   serial
Net:   FEC [PRIME]

Signed-off-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-12 14:28:04 +01:00
Rick Chen
7885ea8568 riscv: board: Add nx25-ae250 to support RISC-V
Add nx25-ae250 board to do platform initializations.

Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Signed-off-by: Greentime Hu <green.hu@gmail.com>
2018-01-12 08:05:12 -05:00
Tom Rini
373b900341 Merge git://git.denx.de/u-boot-sunxi 2018-01-11 14:14:19 -05:00
Tom Rini
1a62f8597c Merge git://git.denx.de/u-boot-video 2018-01-11 13:43:36 -05:00
Tom Rini
6bf634223a Merge git://git.denx.de/u-boot-fsl-qoriq 2018-01-11 11:18:49 -05:00
Hannes Schmelzer
193f6fb9e8 board/BuR: drop LCDC clock manipulation from board code
The clock selection is done now from the am335x-fb code, so there is no
more need doing this in the board code.

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
2018-01-11 15:20:30 +01:00
Hannes Schmelzer
0fcec57752 board/BuR: provide real clock-frequency instead a divider
Actual am335x-fb implementation takes now a real clock frequency instead
a divider. So this component doesn't need to know anymore some base
frequency of the LCDC, we simply provide the pixel-clock frequency.

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
2018-01-11 15:19:51 +01:00
Sumit Garg
1cabeb88eb ls1088ardb: Add SD Secure boot target support
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
[YS: run moveconfig.py -s]
Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-10 12:32:45 -08:00
Sumit Garg
10e7eaf04a armv8: ls1088a: SPL size reduction
Using changes in this patch we were able to reduce approx 8k
size of u-boot-spl.bin image. Following is breif description of
changes to reduce SPL size:
1. Changes in board/freescale/ls1088a/Makefile to remove
   compilation of eth.c and cpld.c in case of SPL build.
2. Changes in board/freescale/ls1088a/ls1088a.c to keep
   board_early_init_f funcations in case of SPL build.
3. Changes in ls1088a_common.h & ls1088ardb.h to remove driver
   specific macros due to which static data was being compiled in
   case of SPL build.

Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-10 12:31:31 -08:00
Ahmed Mansour
44262327aa drivers/misc: Share qbman init between archs
This patch adds changes necessary to move functionality present in
PowerPC folders with ARM architectures that have DPAA1 QBMan hardware

- Create new board/freescale/common/fsl_portals.c to house shared
  device tree fixups for DPAA1 devices with ARM and PowerPC cores
- Add new header file to top includes directory to allow files in
  both architectures to grab the function prototypes
- Port inhibit_portals() from PowerPC to ARM. This function is used in
  setup to disable interrupts on all QMan and BMan portals. It is
  needed because the interrupts are enabled by default for all portals
  including unused/uninitialised portals. When the kernel attempts to
  go to deep sleep the unused portals prevent it from doing so

Signed-off-by: Ahmed Mansour <ahmed.mansour@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-10 12:28:47 -08:00
Tom Rini
084edbb689 Merge git://git.denx.de/u-boot-marvell 2018-01-10 08:05:57 -05:00
Tom Rini
ec75fab302 build: Drop CONFIG_SPL_BUILD guards in some cases
Given gcc-6.1 and later we can now safely have strings discarded when
the functions are unused.  This lets us drop certain cases of not
building something so that we don't have the strings brought in when the
code was discarded.  Simplify the code now by dropping guards we don't
need now.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Chander Kashyap <k.chander@samsung.com>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-01-10 08:05:52 -05:00
Patrice Chotard
c0cdd5adc8 board: stm32: add stm32f469-discovery board support
This board offers :

 _ STM32F469NIH6 microcontroller featuring 2 Mbytes of Flash memory
   and 324 Kbytes of RAM in BGA216 package
 _ On-board ST-LINK/V2-1 SWD debugger, supporting USB reenumeration capability:
     _ Mbed-enabled (mbed.org)
     _ USB functions: USB virtual COM port, mass storage, debug port
 _ 4 inches 800x480 pixel TFT color LCD with MIPI DSI interface and capacitive
   touch screen
 _ SAI Audio DAC, with a stereo headphone output jack
 _ 3 MEMS microphones
 _ MicroSD card connector
 _ I2C extension connector
 _ 4Mx32bit SDRAM
 _ 128-Mbit Quad-SPI NOR Flash
 _ Reset and wake-up buttons
 _ 4 color user LEDs
 _ USB OTG FS with Micro-AB connector
 _ Three power supply options:
 _ Expansion connectors and Arduino™ UNO V3 connectors

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-01-10 08:05:47 -05:00
Patrice Chotard
c8f787760e board: stm32f429-disco: switch to DM STM32 pinctrl and gpio driver
Use available DM stm32f7_gpio.c and pinctrl_stm32.c drivers
instead of board GPIO initialization.

Remove stm32_gpio.c which is no more used and migrate
structs stm32_gpio_regs and stm32_gpio_priv into
arch-stm32f4/gpio.h to not break compilation.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-01-10 08:05:46 -05:00