Add compatible "fsl,imxrt-usdhc" to make mmc working on i.MXRT platforms
with CONFIG_DM_MMC=y.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
- Add sdhci driver for Broadcom iProc platform
- Add a driver callback for power-cycle for mmc
- Implement host_power_cycle callback for stm32_sdmmc2
- spl: dm_mmc: Initialize only the required mmc device
NXP fsl_esdhc controller supports two reference clocks:
platform clock and peripheral clock
Peripheral clock can provide higher clock frequency
which is required to be used for tuning of SD UHS mode
and eMMC HS200/HS400 modes.
Peripheral clock is enabled by default by defining config
option FSL_ESDHC_USE_PERIPHERAL_CLK if eMMC HS200/HS400 modes
are supported.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This converts the following to Kconfig:
CONFIG_FSL_USDHC
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Add IMX8M, TARGET_S32V234EVB to FSL_USDHC list]
Signed-off-by: Tom Rini <trini@konsulko.com>
This is a configuration option specific to the tegra controller.
Doing it this way makes it show up directly under the tegra controller
option, indented one level, as "Disable external clock loopback".
The way it is now, it shows up at the end of the controller list, not
indented, as if it's some kind of generic MMC configuration option.
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Tom Warren <twarren@nvidia.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Select SPL_HS200_SUPPORT if SPL_HS400_SUPPORT is selected as is being
done for the U-boot case.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add support in the driver for handling phy specific registers.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Sync the sdhci0 node from kernel. This changes the compatible that is
required to be there in the driver. Change the same for the SD card node
which is not yet supported in kernel. This also syncs the main_pmx0 node
as a side effect.
Also change the name of the driver to match the compatible in kernel.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
eMMC 5.1+ supports HS400 Enhances Strobe mode without the need for
tuning procedure.
The flow is as following:
- set HS_TIMIMG (Highspeed)
- Host change freq to <= 52Mhz
- set the bus width to Enhanced strobe and DDR8Bit(CMD6),
EXT_CSD[183] = 0x86 instead of 0x80
- set HS_TIMING to 0x3 (HS400)
- Host change freq to <= 200Mhz
- Host select HS400 enhanced strobe complete
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This patch rewrites MMC SPI driver using U-Boot DM
framework and get it's working on SiFive Unleashed
board.
Signed-off-by: Bhargav Shah <bhargavshah1988@gmail.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
The SPL_MMC_TINY implements feature-reduced MMC support
on SPL, and as such, it's more consistent and convenient
to find it as part of the SPL configuration.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
The fsl_esdhc driver was for Freescale eSDHC on MPC83XX/MPC85XX
initially. The later QoriQ series PowerPC processors (which were
evolutions of MPC83XX/MPC85XX), QorIQ series ARM processors, and
i.MX series processors were using this driver for their eSDHCs too.
For the two series processors, the eSDHCs are becoming more and
more different. We should have split it into two drivers, like them
(sdhci-of-esdhc.c/sdhci-esdhc-imx.c) in linux kernel.
This patch is just to create a fsl_esdhc_imx driver which is a copy
of fsl_esdhc driver for i.MX processors. We will convert i.MX processors
to use fsl_esdhc_imx, and clean up the two drivers separately in the
future patches.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
This converts the following to Kconfig:
CONFIG_SUPPORT_EMMC_BOOT
As requested by Michal Simek <michal.simek@xilinx.com>, these boards
have no eMMC so CONFIG_SUPPORT_EMMC_BOOT has not been migrated:
xilinx_zynqmp_zc1275_revB
xilinx_zynqmp_zc1751_xm018_dc4
xilinx_zynqmp_zc1751_xm019_dc5
xilinx_zynqmp_zcu100_revC
xilinx_zynqmp_zcu102_rev1_0
xilinx_zynqmp_zcu102_revA
xilinx_zynqmp_zcu102_revB
xilinx_zynqmp_zcu104_revA
xilinx_zynqmp_zcu104_revC
xilinx_zynqmp_zcu106_revA
xilinx_zynqmp_zcu111_revA
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
The Standard Host Controller Interface (SDHCI) specification version
3.00 adds support for Advanced DMA (ADMA) for both 64 and 32 bit widths
of DMA. ADMA2 uses a table of descriptors for aggregating DMA requests.
This significantly improves read and write throughput.
Add Support for the same.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Add the DM_MMC-compatible DesignWare MMC driver support for Synopsys
ARC devboards. It is created to switch ARC devboards to use DM_MMC.
It required information such as clocks (Bus Interface Unit clock,
Card Interface Unit clock) and SDIO bus width.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
The bounce buffer is used by a few drivers (most of the MMC drivers)
to overcome limitations in their respective DMA implementation.
This moves the configuration to Kconfig and makes it user-selectable
(even though it will be a required feature to make those drivers
work): the expected usage is for drivers depending on this to 'select'
it unconditionally from their respective Kconfig (see follow-up
patches).
This commit includes a full migration using moveconfig.py to ensure
that each commit compiles. To ensure bisectability we update
dependencies of various drivers to now select BOUNCE_BUFFER when needed.
[trini: Squash all patches to ensure bisectability]
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br> [dw_mmc portion]
Reviewed-by: Fabio Estevam <festevam@gmail.com> [mxsmmc portion]
Reviewed-by: Simon Glass <sjg@chromium.org> [tegra portion]
Add driver for the JZ47xx MSC controller.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Allwinner A64 has new mode but doesn't have a mode switch in CCM,
and CCM_MMC_CTRL_MODE_SEL_NEW is not defined, so compilation fails
if MMC_SUNXI_HAS_NEW_MODE is enabled
Introduce new MMC_SUNXI_HAS_MODE_SWITCH option to be able to ifdef usage
of CCM_MMC_CTRL_MODE_SEL_NEW
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
[jagan: update commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
Xilinx is introducing Versal, an adaptive compute acceleration platform
(ACAP), built on 7nm FinFET process technology. Versal ACAPs combine
Scalar Processing Engines, Adaptable Hardware Engines, and Intelligent
Engines with leading-edge memory and interfacing technologies to deliver
powerful heterogeneous acceleration for any application. The Versal AI
Core series has five devices, offering 128 to 400 AI Engines. The series
includes dual-core Arm Cortex™-A72 application processors, dual-core Arm
Cortex-R5 real-time processors, 256KB of on-chip memory with ECC, more
than 1,900 DSP engines optimized for high-precision floating point with
low latency.
The patch is adding necessary infrastructure in place without enabling
platform which is done in separate patch.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
AM654 has an arasan sdhci controller and a mmc phy attached to it.
Add basic support for K3 specific arasan sdhci controller.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add HS400 support.
Selecting HS400 needs first select HS200 according to spec, so use
a dedicated function for HS400.
Add HS400 related macros.
Remove the restriction of only using the low 6 bits of
EXT_CSD_CARD_TYPE, using all the 8 bits.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add support for loading U-Boot on the Broadcom 7445 SoC. This port
assumes Broadcom's BOLT bootloader is acting as the second stage
bootloader, and U-Boot is acting as the third stage bootloader, loaded
as an ELF program by BOLT.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Convert CONFIG_SUPPORT_EMMC_RPMB to Kconfig. Split the command handling
from the underlying support and expose this through CMD_MMC_RPMB.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Add Kconfig entry for the Renesas SDHI variant of the controller
and split the Makefile entries accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
nsd32_mmc was created to support ftsdc010 dm.
It is not necessary to separate both, so merge it
to ftsdc010.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
Convert CONFIG_FTSDC010_SDIO to Kconfig.
So CONFIG_FTSDC010_SDIO can also be
removed from config_whitelist.txt.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
This patch added Kconfig support for CONFIG_ZYNQ_SDHCI_MIN_FREQ
and enabled it in respective defconfig.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch added Kconfig support for CONFIG_ZYNQ_SDHCI_MAX_FREQ
and enabled it in respective defconfig.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Some platforms don't have ADMA controllers. For those platforms, compiling
it out reduces the size of the binary by about 600 bytes.
Leaving the support in doesn't break things as the driver checks at runtime
if the ADMA2 controller is present.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
config_fallbacks.h has some logic that sets HAVE_BLOCK_DEVICE
based on a list of enabled options. Moving HAVE_BLOCK_DEVICE to
Kconfig allows us to drastically shrink the logic in
config_fallbacks.h
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rename HAVE_BLOCK_DEVICE to CONFIG_BLOCK_DEVICE]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_APBH_DMA
CONFIG_APBH_DMA_BURST
CONFIG_APBH_DMA_BURST8
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
[trini: Add in MMC as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
The BCM2835 family of SoCs has 2 different SD controllers: One based on
the SDHCI spec and a custom, home-grown one.
This patch implements a driver for the latter based on the Linux driver.
This is needed so that we can make use of device trees that assume driver
presence of both SD controllers.
Signed-off-by: Alexander Graf <agraf@suse.de>
This allows using CONFIG_IS_ENABLED(MMC_WRITE) to compile out code
needed only if write support is required.
The option is added for u-boot and for SPL
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Not all boards have an eMMC and not all users have a need for this.
Allow to compile it out. By default it is still included.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Supporting USH and HS200 increases the code size as it brings in IO voltage
control, tuning and fatter data structures.
Use Kconfig configuration to select which of those features should be
built in.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This allows to compile out the log message by tweaking the LOGLEVEL.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
With certain SD cards like Kingston 8GB/16GB UHS card, it is seen that
MMC_CMD_ALL_SEND_CID cmd fails on first attempt, but succeeds
subsequently. Therefore, retry MMC_CMD_ALL_SEND_CID cmd a few time
as done in Linux kernel.
Similarly, it is seen that MMC_CMD_SET_BLOCKLEN may fail on first
attempt, therefore retry this cmd a few times as done in kernel.
To make it clear that those are optionnal workarounds, a new Kconfig
option 'MMC_QUIRKS' is added (enabled by default).
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
no functionnal changes.
In order to add the support for the high speed SD and MMC modes, it is
useful to track this information.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert this driver to driver model.
This driver is also used by VEXPRESS platforms which doesn't
use driver model.
Tested on STM32F746 and STM32F769 platforms.
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
