commit ce62bef8fac559e27245259882e45f19cdc293ad upstream.
- fix JIRA A7K8K-5056
- remove TEST_PATTERN write at the load patern stage earlier to WL SUP stage
- the WL SUP stage already writes this pattern to the memory, if the pattern exist at the memory
then the algorithm will fail, since it think that there are no phase to correct
Signed-off-by: Moti Buskila <motib@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
The values of left_edge[0] and right_edge[0] are overwritten before they
are used. Remove the superfluous assignments.
Fixes: 285b3cb939 ("dm: ddr: socfpga: fix gen5 ddr driver to not use bss")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use CONFIG_IS_ENABLED() macro, which provides more convenient
way to check $(SPL)DM_I2C/$(SPL)DM_I2C_GPIO configs
for both SPL and U-Boot proper.
CONFIG_IS_ENABLED(DM_I2C) expands to:
- 1 if CONFIG_SPL_BUILD is undefined and CONFIG_DM_I2C is set to 'y',
- 1 if CONFIG_SPL_BUILD is defined and CONFIG_SPL_DM_I2C is set to 'y',
- 0 otherwise.
All occurences were replaced automatically using these bash cmds:
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C/if !CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C/if CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C)/CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C_GPIO/if !CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C_GPIO/if CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C_GPIO)/CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
When doing DDR scrub, the DDR may enter into self refresh if the
selfref_en is enabled before DDR scrub. This will cause scrub
can't complete that SBRSTAT.scrub_done won't be set.
Since the selfref_en can be programmed during the course of
normal operation, move it after DDR scrub
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl/09LURHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrebjwwf/fHRjYsAY/Yj/+y1xgo3L3sphIvQUqTDF
KkLl+kHdV5r8W/HJULxLQcF2r7pcPEI6TAQxuj3qQ5SUvm2HviS8GHGPawDEwyht
HgBp9VD56+HUadMfnbG//DVS73ycbL4XSKlYqpkINEejtnlttsCIawUXX5cTyGM/
59VkgnKrKvJQRUXvYLa8MTugTs4fkPJGDqhActBk/7SP1SImj+rfalNSqA2/dx6y
2RnPCSzB1x2231KSj+B1NgGlR3Xb8P8zgh20ijcEU/hrlXBTZyi7K7f4SJR30Efu
LYkkuj4VbxcV/25RozR0fmknqCs0QyAI+/dql6TNtbTSPC/jAfj0jQ==
=9kN3
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-5jan21' of git://git.denx.de/u-boot-dm into next
Driver model: make some udevice fields private
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
Most drivers use these access methods but a few do not. Update them.
In some cases the access is not permitted, so mark those with a FIXME tag
for the maintainer to check.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
This name is far too long. Rename it to remove the 'data' bits. This makes
it consistent with the platdata->plat rename.
Signed-off-by: Simon Glass <sjg@chromium.org>
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
LX2162 is LX2160 based SoC, it has same die as of LX2160
with different packaging.
LX2162A support 64-bit 2.9GT/s DDR4 memory, i2c, micro-click module,
microSD card, eMMC support, serial console, qspi nor flash, qsgmii,
sgmii, 25g, 40g, 50g network interface, one usb 3.0 and serdes
interface to support three PCIe gen3 interface.
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
[Fixed whitespace errors]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The sandbox is built with the SDL2 library with invokes the X11 library
which in turn calls getc(). But getc() in glibc is defined as
int getc(FILE *)
This does not match our definition.
int getc(void)
The sandbox crashes when called with parameter -l.
Rename our library symbol getc() to getchar().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently checkpatch is not happy about this file:
total: 14 errors, 2 warnings, 7 checks, 359 lines checked
Improve the coding style so that it can now report:
total: 0 errors, 0 warnings, 6 checks, 360 lines checked
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The Linux coding style guide (Documentation/process/coding-style.rst)
clearly says:
It's a **mistake** to use typedef for structures and pointers.
Besides, using typedef for structures is annoying when you try to make
headers self-contained.
Let's say you have the following function declaration in a header:
void foo(bd_t *bd);
This is not self-contained since bd_t is not defined.
To tell the compiler what 'bd_t' is, you need to include <asm/u-boot.h>
#include <asm/u-boot.h>
void foo(bd_t *bd);
Then, the include direcective pulls in more bloat needlessly.
If you use 'struct bd_info' instead, it is enough to put a forward
declaration as follows:
struct bd_info;
void foo(struct bd_info *bd);
Right, typedef'ing bd_t is a mistake.
I used coccinelle to generate this commit.
The semantic patch that makes this change is as follows:
<smpl>
@@
typedef bd_t;
@@
-bd_t
+struct bd_info
</smpl>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Add logic to automatically update umctl2's setting based
on phy training CDD value for rank to rank space issue
Acked-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Oliver Chen <Oliver.Chen@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
the DRAM Controller in i.MX8MP will support a feature called "Inline ECC".
This is supported for all 3 supported DRAM technologies (LPDDR4, DDR4 and
DDR3L). When this feature is enabled by software, the DRAM Controller
reserves 12.5% of DRAM capacity for ECC information, and presents only
the non-ECC portion (lower 87.5% of the installed capacity of DRAM) to
the rest of the SoC.
The DRAM memory can be divided into 8 regions so that if a use case only
requires ECC protection on a subset of memory, then only that subset of
memory need support inline ECC. If this occurs, then there is no
performance penalty accessing the non-ECC-protected memory (no need to
access ECC for this portion of the memory map). This is all configured
with the DRAM Controller.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The 'selfref_en' should be bit'0', so correct the setting to
enable the auto self-refresh.
Reviewed-by: Jian Li <jian.li@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
There is no DDR_SS_GPR0 exits on i.MX8MN, so skip setting
this register on i.MX8MN.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Measurements on actual hardware shown that the read ODT is early by 3
clocks. Adjust the calculation to avoid this.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
[upstream https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell/pull/22]
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
In the Armada 385 functional spec (MV-S109094-00 Rev. C) the read sample
delay fields are 5 bits wide. Use the correct bitmask of 0x1f when
extracting the value.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
[upstream https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell/pull/22]
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.
Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.
This requires quite a few header-file additions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
The value of local variable ecc is immediately overwritten. So we can
remove the first assignment.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
For some layouts it is necessary to adjust the CK_DELAY parameter to
successfully complete DDR training. Add the ability to specify the
CK_DELAY in the mv_ddr_topology_map.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
This reverts commit 2a5d5d27ed.
The commit breaks uboot boot (hang in ddr init)
on many PowerPC boards like P3041DS, P4080DS
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl48iogACgkQfxc6PpAI
reaVzAf/an3/yKe6r3CVWlcRV6H/dVg1ApnnLpX7jS0p0b++oCVvOiy7z1WPXj3k
b1SSgENDeeZ/8EHio+Gf7ZidH/TGEj7L6YEFwd1t60GMkZiWEkNf4Z53tw482YG+
96hoPD+ySTW+ddIdVHWAFG2I4aEiKHANJAp/ItNdD+rLbrEwNQy+eiK5JTOk80B6
/X8AJCLZeAC1s7vs+2+WolgjT78QGzA9HHalMiublcqh0ivKKk0QeQiOKKPe8JYJ
om5YY1TxayQ60Xmo5f39/SBfzEEklxw83sU9o1tBeYzyVUpu7fQdkxiDbWdsij77
DgwLdeYQJGbN+hdSWE0gjTqyhW+lWA==
=KRoA
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-6feb20' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
sandbox conversion to SDL2
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add DDR2 support to Gen5 DRAM driver. As the DDR2 macro names generated
by Quartus are named differently than the DDR3 ones, use anon unions to
store them in the same structures, without growing their size.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This function parameter usage of load_addr was incorrectly caught in
the clarifying renames of commit bb872dd930, which results in boot
failures on Marvell A38x.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Patch-to: Simon Glass <sjg@chromium.org>
DDR clock out might be unrelated to the number of active chip-select.
For example, the board might have two DDR components, but only one
chip-select. The clk_enable mask allows the board to enable DDR clocks
regardless of active chip-selects.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>
These global variables are quite short and generic. In fact the same name
is more often used locally for struct members and function arguments.
Add a image_ prefix to make them easier to distinguish.
Signed-off-by: Simon Glass <sjg@chromium.org>
We will generate DRAM 4000MT/s as default for i.MX8MP.
So need DRAM PLL to generate 1000Mhz clock to DDR PHY and controller.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The ECC registers in the SDRAM HMC Adapter should always
be accessible (both when ECC is enabled and disabled).
Currently, the registers are accessible only when ECC is enabled.
The ECC Enabled bit is used to determine the status of
ECC by later OSes so always allow access.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Enable TCU access through the Stratix10 CCU so that the
SMMU can access the SDRAM.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
