Commit graph

282 commits

Author SHA1 Message Date
Shengzhou Liu
d36740462a driver/ddr/fsl: Check condition for erratum A-009803
Add condition of checking the enabled of address parity
for erratum A-009803, if parity is not enabled, the
workaround of erratum A-009803 should not be applied.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-03 14:12:49 -07:00
York Sun
b06f6f2f03 drivers/ddr/fsl: Disabling data init if ECC is not enabled
If ECC is not enabled, data init can be disabled to speed up booting.

Signed-off-by: York Sun <york.sun@nxp.com>
2016-06-03 14:12:48 -07:00
York Sun
5605dc6135 drivers/ddr/fsl: Fix timing_cfg_2 register
Commit 34e026f9 added one extra bit to wr_lat for timing_cfg_2, but
with wrong bit position. It is bit 13 in big-endian, or left shift
18 from LSB. This error hasn't had any impact because we don't have
fast enough DDR4 using the extra bit so far.

Signed-off-by: York Sun <york.sun@nxp.com>
2016-06-03 14:12:06 -07:00
Shengzhou Liu
d8e5163ad8 drivers/ddr/fsl: Update clk_adjust of sdram_clk_cntl
The clk_adjust is of SDRAM_CLK_CNTL[5:8] 4-bits on MPC85xx and P-series,
but is of SDRAM_CLK_CNTL[5:9] 5-bits on T-series and LS-series SoCs.
We should update it to adapt the case that clk_adjust is odd data.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-03 14:06:35 -07:00
Tom Rini
fc15b9beed Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2016-05-24 13:42:03 -04:00
Marek Vasut
29b59353fe arm: mvebu: a38x: Weed out floating point use
For reason unknown, recently, the DDR init code writers are really fond
of hiding some small floating point operating deep in their creations.
This patch removes one from the Marvell A38x code.

Instead of returning size of chip as float from ddr3_get_device_size()
in GiB units, return it as int in MiB units. Since this would interfere
with the huge switch code in ddr3_calc_mem_cs_size(), rework the code
to match the change.

Before this patch, the cs_mem_size variable could have these values:
 ( { 16, 32 } x { 8, 16 } x { 0.01, 0.5, 1, 2, 4, 8 } ) / 8 =
   { 0.000000, 0.001250, 0.002500, 0.005000, 0.062500, 0.125000,
     0.250000, 0.500000, 1.000000, 2.000000, 4.000000, }
The switch code checked for a subset of the resulting RAM sizes, which
is in range 128 MiB ... 2048 MiB.

With this patch, the cs_mem_size variable can have these values:
 ( { 16, 32 } x { 8, 16 } x { 0, 512, 1024, 2048, 4096, 8192 } ) / 8 =
   { 0, 64, 128, 256, 512, 1024, 2048, 4096 }
To retain previous behavior, filter out 0 MiB (invalid size), 64 MiB
and 4096 MiB options.

Removing the floating point stuff also saves 1.5k from text segment:
  clearfog       :  spl/u-boot-spl:all -1592  spl/u-boot-spl:text -1592

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2016-05-20 11:01:00 +02:00
Shengzhou Liu
019a147b65 driver/ddr/fsl: Add workaround for erratum A-010165
During DDR-2133 operation, the transmit data eye margins determined
during the memory controller initialization may be sub-optimal, set
DEBUG_29[12] and DEBUG_29[13:16] = 4'b0100 before MEM_EN is set.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-18 08:51:47 -07:00
Shengzhou Liu
5fc62fe570 driver/ddr/fsl: Add workaround for erratum A-009801
The initial training for the DDRC may provide results that are not
optimized. The workaround provides better read timing margins.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-17 09:26:53 -07:00
Shengzhou Liu
4a68489e12 drivers/ddr/fsl: update workaround for erratum A-008511
Per the latest erratum document, update step 4 and step 8, only
DEBUG_29[21] is changed, all other bits should not be changed.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-17 09:26:42 -07:00
Vagrant Cascadian
eae4b2b67b Fix spelling of "occurred".
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-02 18:37:09 -04:00
Marek Vasut
e026b984e6 ddr: altera: Repair DQ window centering code
The code uses a lot of signed numbers, which ended up in variables
of unsigned type, which resulted in all sorts of underflows. This
in turn caused incorrect calibration on certain boards. Moreover,
repair the readout of the DQ delay, which was being pulled from
wrong register.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
2016-04-20 11:28:45 +02:00
Marek Vasut
85f76628a0 ddr: altera: Staticize global variables
Just staticize global variables in sequencer, since there is no
point in having these symbols available outside of the DDR code.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
2016-04-20 11:28:45 +02:00
Marek Vasut
ea9aa2414e ddr: altera: Make DLEVEL behavior inclusive
Originally, the DLEVEL selects the debug level within the sequencer code,
but only displays the messages on that particular debug level. Tweak the
handling such that for particular debug level, debug messages on that
level and lower are displayed. This allows better regulation of debug
message verbosity.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
2016-04-20 11:28:45 +02:00
Marek Vasut
70ed80af46 ddr: altera: Zero DM IN delay in scc_mgr_zero_group()
This one last set of delay configuration registers was not properly
zeroed out originally, fix it and zero them out.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
2016-04-20 11:28:45 +02:00
Marek Vasut
f3f777cdf0 ddr: altera: Remove unnecessary ODT mode config
There is no point in resetting the ODT setting if the write test
failed, since the code will always retry the calibration and thus
reconfigure the ODT anyway OR the code will fail calibration and
halt.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
2016-04-20 11:28:44 +02:00
Marek Vasut
f5f8c411de ddr: altera: Remove unnecessary update of the SCC
Every invocation of the scc_mgr_set_dqs_en_delay_all_ranks() is
followed by SCC manager update. Moreover, only this function
triggers the SCC manager update internally. Thus, remove the
internal invocation to avoid triggering the update twice.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
2016-04-20 11:28:44 +02:00
Marek Vasut
164eb23f49 ddr: altera: Fix DRAM end value in protection rule
The hi address bitfield in the protection rule must be set to
the last address in the region which the rule represents. The
behavior is now in-line with code generated by Quartus 15.1 .

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
2016-04-20 11:28:44 +02:00
Marek Vasut
8e9e62c946 ddr: altera: Fix scc_mgr_set() argument order
The code should be setting registers to zero, not one register to value.
Swap the order of arguments to correct the behavior. The behavior is now
in-line with code generated by Quartus 15.1 .

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
2016-04-20 11:28:44 +02:00
Marek Vasut
bba7711092 ddr: altera: Tweak DQS tracking enable handling
In the most unlikely case the DQS tracking was to be disabled,
make sure we do not errornously re-enable it. Note that DQS
tracking is enabled on all systems observed thus far.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
2016-04-20 11:28:44 +02:00
Marek Vasut
abaf83619c ddr: altera: Replace ad-hoc constant with macro
The bit 22 is in fact DQS tracking enable bit (dqstrken) and there
is a macro for this bit already, so use it.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
2016-04-20 11:28:43 +02:00
Alexander Merkle
dd8d8da3d7 Fix typo choosen in comments and printf logs
Minor change: chosen is written with one "o".
No code change here, only comment & printf.

Signed-off-by: Alexander Merkle <alexander.merkle@lauterbach.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-03-27 09:12:23 -04:00
Dirk Eibach
44876bf9e8 arm: mvebu: Fix ddr3_init() cpu config
Armada 38x has a maximum of two cores. Probably copy/paste
bug from Armada XP.

Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
2016-03-24 09:36:40 +01:00
Shengzhou Liu
dd8e740c78 driver/ddr/fsl: Add workaround for erratum A-009803
During initial DDR training, false parity errors may be detected.
This patch adds workaround to fix the erratum.
Tested on LS2085QDS and LS2080RDB.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-21 12:42:13 -07:00
Shengzhou Liu
eb118807a4 driver/ddr/fsl: Add address parity support for DDR4 UDIMM/discrete
Add support of address parity for DDR4 UDIMM or discrete memory.
It requires to configurate corresponding MR5[2:0] and
TIMING_CFG_7[PAR_LAT]. Parity can be turned on by hwconfig,
e.g. hwconfig=fsl_ddr:parity=on.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-21 12:42:13 -07:00
Bin Meng
a187559e3d Use correct spelling of "U-Boot"
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
2016-02-06 12:00:59 +01:00
Purna Chandra Mandal
9ffa7a35ef drivers: ddr: Add DDR2 SDRAM controller driver for Microchip PIC32.
This driver initializes PIC32 DDR2 SDRAM controller and internal DDR2 Phy module.
DDR2 controller operates in half-rate mode (upto 533MHZ frequency).

Signed-off-by: Paul Thacker <paul.thacker@microchip.com>
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-02-01 22:14:01 +01:00
Ed Swarthout
81dfdee0dc drivers/ddr/fsl: fsl_ddr_sdram_size remove unused controllers
Following commit 61bd2f75, exclude unused DDR controller from
calculating RAM size for SPL boot.

Signed-off-by: Ed Swarthout <Ed.Swarthout@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25 08:24:16 -08:00
Shengzhou Liu
a994b3deb0 driver/ddr/fsl: Add workaround for A009663
Erratum A-009663 workaround requires to set DDR_INTERVAL[BSTOPRE] to 0
before setting DDR_SDRAM_CFG[MEM_EN] and set DDR_INTERVAL[BSTOPRE]
to the desired value after DDR initialization has completed.

When DDR controller is configured to operate in auto-precharge
mode(DDR_INTERVAL[BSTOPRE]=0), this workaround is not needed.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25 08:24:15 -08:00
Shengzhou Liu
0d3972cfcd fsl/ddr: Add workaround for ERRATUM_A009942
During the receive data training, the DDRC may complete on a
non-optimal setting that could lead to data corruption or
initialization failure.

Workaround: before setting MEM_EN, set DEBUG_29 register with
specific value for different data rates.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25 08:24:14 -08:00
Tom Rini
5b8031ccb4 Add more SPDX-License-Identifier tags
In a number of places we had wordings of the GPL (or LGPL in a few
cases) license text that were split in such a way that it wasn't caught
previously.  Convert all of these to the correct SPDX-License-Identifier
tag.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-01-19 08:31:21 -05:00
Marek Vasut
1720fad0f1 ddr: altera: Init the rule ID in debug code
Init the rule ID, otherwise the debug code will always dump the
protection settings entry 0.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
2016-01-16 07:07:22 +01:00
Phil Sutter
4444d230ac mvebu: axp: Rename MV_DDR_32BIT to CONFIG_DDR_32BIT
This should make it clear that this symbol is meant to be defined by
board headers.

Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-01-14 14:08:59 +01:00
Phil Sutter
7e1e59a7b7 axp: Fix debugging support in DDR3 write leveling
If MV_DEBUG_WL is defined, DEBUG_WL_S and DEBUG_WL_D macros are missing.
In addition to that, get rid of debug output printing non-existent
counter variable.

Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-01-14 14:08:59 +01:00
Stefan Roese
698ffab239 arm: mvebu: Make ECC support configurable on Armada XP
Currently, ECC support is enabled for all Armada XP boards. So the
DDR3 driver tries to configure the controller with ECC support, even
on boards without ECC. This patch makes this ECC optional which now
can be configured on a board-per-board basis.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Phil Sutter <phil@nwl.cc>
2016-01-14 14:08:59 +01:00
Stefan Roese
cdf1d240ba arm: mvebu: ddr: Fix compilation warning
gcc 5.1 generates this new warning (for Armada 38x platforms):

drivers/ddr/marvell/a38x/ddr3_debug.c: In function 'hws_ddr3_tip_read_training_result':
drivers/ddr/marvell/a38x/ddr3_debug.c:177:40: warning: 'sizeof' on array
  function parameter 'result' will return size of 'enum hws_result (*)[1]' [-Wsizeof-array-argument]
  memcpy(result, training_result, sizeof(result));
                                        ^
drivers/ddr/marvell/a38x/ddr3_debug.c:171:31: note: declared here
  u32 dev_num, enum hws_result result[MAX_STAGE_LIMIT][MAX_INTERFACE_NUM])
                               ^

Since this functions is not referenced anywhere, lets just remove it.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
2016-01-14 14:08:59 +01:00
Yao Yuan
000f4e7686 move erratum a008336 and a008514 to soc specific file
As the errata A008336 and A008514 do not apply to all LS series SoCs
(such as LS1021A, LS1043A) we move them to an soc specific file

Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-12-15 08:57:32 +08:00
Shengzhou Liu
a46b1852de fsl/ddr: updated ddr errata-A008378 for arm and power SoCs
DDR errata-A008378 applies to LS1021-20-22A-R1.0, T1023-R1.0,
T1024-R1.0, T1040-42-20-22-R1.0/R1.1, it has been fixed on
LS102x Rev2.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-12-13 18:27:28 -08:00
York Sun
6c6e006a20 driver/ddr/fsl: Update timing config for heavy load
In case four chip-selects are all active, the turnaround times need to
increase to avoid overlapping under heavy load.

Signed-off-by: York Sun <yorksun@freescale.com>
2015-12-13 18:27:27 -08:00
York Sun
7cc079989d driver/ddr/fsl: Update workaround for A008511 for vref range
The workaround requires different setting for range 1 vs 2.
Also adjust timeout value for waiting for controller to be idle.

Signed-off-by: York Sun <yorksun@freescale.com>
2015-12-13 18:27:27 -08:00
York Sun
8a51429e00 driver/ddr/fsl: Update MR5 RTT park
For four chip-selects enabled case, RTT is parked on all of them.

Signed-off-by: York Sun <yorksun@freescale.com>
2015-12-13 18:27:27 -08:00
York Sun
0fb7197436 driver/ddr/fsl: Update DDR4 MR6 for Vref range
MR6 bit 6 is set accrodingly for range 1 or 2, per JEDEC spec.

Signed-off-by: York Sun <yorksun@freescale.com>
2015-12-13 18:27:27 -08:00
York Sun
19601dd99c driver/ddr/fsl: Update DDR4 RTT values
DDR4 has different RTT value and code according to JEDEC spec. Update
the macros and options .

Signed-off-by: York Sun <yorksun@freescale.com>
2015-12-13 18:27:27 -08:00
York Sun
da305b9f57 drivers/ddr/fsl: Fix typo in BIST test for DDR4
BIST test code has a typo, resulting the binding registers not
maintained as expected. This typo results BIST runs twice on
the covered memory.

Signed-off-by: York Sun <yorksun@freescale.com>
Reported-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
2015-11-30 09:11:12 -08:00
York Sun
61bd2f75f5 drivers/ddr/fsl: Enable detection of one DDR controller operation for LSCH3
Freescale LSCH3 platforms use two DDR controlers interleaving mode out of
reset. It can be configured to disable one controller. To support this
operation, the driver needs to detect and skip the disabled controller.

Signed-off-by: York Sun <yorksun@freescale.com>
2015-11-30 09:11:11 -08:00
Prabhakar Kushwaha
06b5301043 armv8: ls2085a: Add support of LS2085A SoC
Freescale's LS2085A is a another personality of LS2080A SoC with
support of AIOP and DP-DDR.
This Patch adds support of LS2085A Personality.

Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Updated MAINTAINERS files
           Dropped #ifdef in cpu.h
           Add CONFIG_SYS_NS16550=y in defconfig]
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 09:10:47 -08:00
Prabhakar Kushwaha
449372148f armv8: LS2080A: Rename LS2085A to reflect LS2080A
LS2080A is a prime personality of Freescale’s LS2085A. It is a non-AIOP
personality without support of DP-DDR, L2 switch, 1588, PCIe endpoint etc.
So renaming existing LS2085A code base to reflect LS2080A (Prime personality)

Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Dropped #ifdef in cpu.c for cpu_type_list]
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 08:53:04 -08:00
Dirk Eibach
a21b4f0f99 arm: mvebu: Fix SAR1_CPU_CORE_MASK
SAR1_CPU_CORE_MASK was wrong, probably copy/paste
from another architecture.

Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
2015-11-17 23:41:41 +01:00
Kevin Smith
544acb07ec arm: mvebu: a38x: Remove unsupported topologies
A lot of extra configuration information was left over in the
Marvell serdes and DDR3 initialization code for boards that
U-boot does not support.  Remove this extra config information,
and the concept of fixing up board topologies with information
loaded from an EEPROM.  If this needs to be done, it should be
handled in the board file, not in core code.

Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
2015-11-17 23:41:41 +01:00
Tom Rini
da58dec866 Various Makefiles: Add SPDX-License-Identifier tags
After consulting with some of the SPDX team, the conclusion is that
Makefiles are worth adding SPDX-License-Identifier tags too, and most of
ours have one.  This adds tags to ones that lack them and converts a few
that had full (or in one case, very partial) license blobs into the
equivalent tag.

Cc: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-11-10 09:19:52 -05:00
Joakim Tjernlund
e368c20607 drivers/ddr/fsl_ddr: Make SR_IE configurable
SR_IE(Self-refresh interrupt enable) is needed for
Hardware Based Self-Refresh. Make it configurable and let
board code handle the rest.

Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-30 09:19:41 -07:00