The FEC interface mode is now configured in common board_interface_eth_init()
and called by FEC MAC driver when appropriate. Drop the board side duplicates
if the same functionality.
Signed-off-by: Marek Vasut <marex@denx.de>
The EQoS interface mode is now configured in common board_interface_eth_init()
and called by EQoS MAC driver when appropriate. Drop the board side duplicates
if the same functionality.
Signed-off-by: Marek Vasut <marex@denx.de>
The i.MX8MP DHCOM SoM may be populated with either KSZ9131RNXI RGMII PHY
or LAN8740Ai RMII PHY attached to EQoS MAC, and either external RGMII PHY
or LAN8740Ai RMII PHY attached to FEC MAC. The SoM configuration can be
detected for each MAC by reading RX_CTL pull resistor state early on boot.
Make use of this, detect the exact PHY configuration, and patch control DT
accordingly so that the ethernet is configured correctly in U-Boot.
Signed-off-by: Marek Vasut <marex@denx.de>
The DH electronics i.MX8M Plus DHCOM SoM currently supports only 4 GiB
of DRAM population option. Add another population option with 2 GiB of
DRAM. The chips used on the 2 GiB option are 2x K4F6E3S4HM-MGCJ .
Signed-off-by: Marek Vasut <marex@denx.de>
The PCA9450 reset configuration can now be performed by the PCA9450 PMIC
driver itself, remove the hard-coded variant from board code and let the
PMIC driver perform this task using one-liner:
```
$ sed -i '/set WDOG_B_CFG to cold reset/,+2 d' $(git grep -l PCA9450_RESET_CTRL.*0xA1 board/)
```
Venice and i.MX93 EVK required slight manual fix up.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Commit 99c7cc58e1 ("ddr: imx: Add i.MX9 DDR controller driver")
contains an inobvious side-effect which renders all systems using
DRAM controller at 3732 MT/s unbootable. The change is located in
ddrphy_init_set_dfi_clk(), where the switch case statement entry
3732 changed to entry 3733, so any board with DDR calibration data
for 3732 MT/s operations needs to be updated to 3733 MT/s to match
the change.
Since there is currently only one such board, update the board instead
of handling both 3732 and 3733 options in the driver. It is likely the
NXP MX8MP RPA update will follow and use the later value too.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
To reduce code duplication, let the imx8 based DH boards use the common
code for setting up their MAC addresses.
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Add support for DH electronics i.MX8M Plus DHCOM SoM on PDK2 carrier board.
Currently supported are serial console, EQoS and FEC ethernets, eMMC, SD,
SPI NOR and USB 3.0 host.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
