We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.
Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.
This requires quite a few header-file additions.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should not be using typedefs and these make it harder to use
forward declarations (to reduce header file inclusions). Drop the typedef.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this uncommon header out of the common header.
Fix up some style problems in flash.h while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
The inode list uses version and ino, the dirent list uses version and pino.
This information is collected during scanning, reducing accesses to flash
and significantly speeding up ls and read.
Signed-off-by: Petr Borsodi <petr.borsodi@i.cz>
Obsolete nodes (ie. without the JFFS2_NODE_ACCURATE flag) were ignored
because they had seemingly invalid crc. This could lead to finding
the phantom node header in obsolete node data.
Signed-off-by: Petr Borsodi <petr.borsodi@i.cz>
As u-boot doesn't support the metadata_csum feature, writing to a
filesystem with this feature enabled will fail, as expected. However,
during the process, a journal state check is performed, which could
result in:
- a fs recovery if the fs wasn't umounted properly
- the fs being marked dirty
Both these cases result in a superblock change, leading to a mismatch
between the superblock checksum and its contents. Therefore, Linux will
consider the filesystem heavily corrupted and will require e2fsck to be
run manually to boot.
By bypassing the journal state check, this patch ensures the superblock
won't be corrupted if the filesystem has metadata_csum feature enabled.
Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
When logical address of a regular extent is 0, the extent is sparse and
consists of all zeros.
Without this when sparse extents are used in a file reading fails with
Cannot map logical address 0 to physical
Signed-off-by: Marek Behún <marek.behun@nic.cz>
For certain btrfs files with compressed file extent, uboot will fail to
load it:
btrfs_read_extent_reg: disk_bytenr=14229504 disk_len=73728 offset=0 nr_bytes=131
072
decompress_lzo: tot_len=70770
decompress_lzo: in_len=1389
decompress_lzo: in_len=2400
decompress_lzo: in_len=3002
decompress_lzo: in_len=1379
decompress_lzo: in_len=88539136
decompress_lzo: header error, in_len=88539136 clen=65534 tot_len=62580
NOTE: except the last line, all other lines are debug output.
Btrfs lzo compression uses its own format to record compressed size
(segment header, LE32).
However to make decompression easier, we never put such segment header
across page boundary.
In above case, the xxd dump of the lzo compressed data looks like this:
00001fe0: 4cdc 02fc 0bfd 02c0 dc02 0d13 0100 0001 L...............
00001ff0: 0000 0008 0300 0000 0000 0011 0000|0000 ................
00002000: 4705 0000 0001 cc02 0000 0000 0000 1e01 G...............
'|' is the "expected" segment header start position.
But in that page, there are only 2 bytes left, can't contain the 4 bytes
segment header.
So btrfs compression will skip that 2 bytes, put the segment header in
next page directly.
Uboot doesn't have such check, and read the header with 2 bytes offset,
result 0x05470000 (88539136), other than the expected result
0x00000547 (1351), resulting above error.
Follow the btrfs-progs restore implementation, by introducing tot_in to
record total processed bytes (including headers), and do proper page
boundary skip to fix it.
Please note that, current code base doesn't parse fs_info thus we can't
grab sector size easily, so it uses PAGE_SIZE, and relying on fs open
time check to exclude unsupported sector size.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Cc: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Although in theory u-boot fs driver could easily support more sector
sizes, current code base doesn't have good enough way to grab sector
size yet.
This would cause problem for later LZO fixes which rely on sector size.
And considering that most u-boot boards are using 4K page size, which is
also the most common sector size for btrfs, rejecting fs with
non-page-sized sector size shouldn't cause much problem.
This should only be a quick fix before we implement better sector size
support.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Cc: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Just a cleanup. These immediate numbers make my eyes hurt.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Cc: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
We need to align the cache buffer to ARCH_DMA_MINALIGN in order to avoid
access errors like
CACHE: Misaligned operation at range [be0231e0, be0235e0]
seen on the MCIMX7SABRE.
Fixes: d5aee659f2 ("fs: ext4: cache extent data")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl48iogACgkQfxc6PpAI
reaVzAf/an3/yKe6r3CVWlcRV6H/dVg1ApnnLpX7jS0p0b++oCVvOiy7z1WPXj3k
b1SSgENDeeZ/8EHio+Gf7ZidH/TGEj7L6YEFwd1t60GMkZiWEkNf4Z53tw482YG+
96hoPD+ySTW+ddIdVHWAFG2I4aEiKHANJAp/ItNdD+rLbrEwNQy+eiK5JTOk80B6
/X8AJCLZeAC1s7vs+2+WolgjT78QGzA9HHalMiublcqh0ivKKk0QeQiOKKPe8JYJ
om5YY1TxayQ60Xmo5f39/SBfzEEklxw83sU9o1tBeYzyVUpu7fQdkxiDbWdsij77
DgwLdeYQJGbN+hdSWE0gjTqyhW+lWA==
=KRoA
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-6feb20' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
sandbox conversion to SDL2
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
The code for handing file overwrite incorrectly assumed that the file on
disk is always contiguous. This resulted in corrupting disk structure
every time when write to existing fragmented file happened. Fix this
by adding proper check for cluster discontinuity and adjust chunk size
on each partial write.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
This patch partially fixes the issue revealed by the following test
script:
--->8-fat_test1.sh---
#!/bin/bash
make sandbox_defconfig
make
dd if=/dev/zero of=/tmp/10M.img bs=1024 count=10k
mkfs.vfat -v /tmp/10M.img
cat >/tmp/cmds <<EOF
x
host bind 0 /tmp/10M.img
fatls host 0
mw 0x1000000 0x0a434241 0x1000 # "ABC\n"
mw 0x1100000 0x0a464544 0x8000 # "DEF\n"
fatwrite host 0 0x1000000 file0001.raw 0x1000
fatwrite host 0 0x1000000 file0002.raw 0x1000
fatwrite host 0 0x1000000 file0003.raw 0x1000
fatwrite host 0 0x1000000 file0004.raw 0x1000
fatwrite host 0 0x1000000 file0005.raw 0x1000
fatrm host 0 file0002.raw
fatrm host 0 file0004.raw
fatls host 0
fatwrite host 0 0x1100000 file0007.raw 0x4000
fatwrite host 0 0x1100000 file0007.raw 0x4000
reset
EOF
./u-boot </tmp/cmds
#verify
rm -r /tmp/result /tmp/model
mkdir /tmp/result
mkdir /tmp/model
yes ABC | head -c 4096 >/tmp/model/file0001.raw
yes ABC | head -c 4096 >/tmp/model/file0003.raw
yes ABC | head -c 4096 >/tmp/model/file0005.raw
yes DEF | head -c 16384 >/tmp/model/file0007.raw
mcopy -n -i /tmp/10M.img ::file0001.raw /tmp/result
mcopy -n -i /tmp/10M.img ::file0003.raw /tmp/result
mcopy -n -i /tmp/10M.img ::file0005.raw /tmp/result
mcopy -n -i /tmp/10M.img ::file0007.raw /tmp/result
hd /tmp/10M.img
if diff -urq /tmp/model /tmp/result
then
echo Test okay
else
echo Test fail
fi
--->8---
Overwritting a discontiguous test file (file0007.raw) no longer causes
corruption to file0003.raw, which's data lies between the chunks of the
test file. The amount of data written to disk is still incorrect, what
causes damage to the file (file0005.raw), which's data lies next to the
test file. This will be fixed by the next patch.
Feel free to prepare a proper sandbox/py_test based tests based on the
provided test scripts.
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
linux_compat.c is the best place for kmemdup(), which is currenly used
only in ubifs.c, but will also be used when other kernel files
(in my case, lib/crypto/x509_cert_parser.c and pkcs7_parser.c) will be
imported. So just move it.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Unlink test for FAT file system seems to fail at test_unlink2.
(When I added this test, I haven't seen any errors though.)
for example,
===8<===
fs_obj_unlink = ['fat', '/home/akashi/tmp/uboot_sandbox_test/128MB.fat32.img']
def test_unlink2(self, u_boot_console, fs_obj_unlink):
"""
Test Case 2 - delete many files
"""
fs_type,fs_img = fs_obj_unlink
with u_boot_console.log.section('Test Case 2 - unlink (many)'):
output = u_boot_console.run_command('host bind 0 %s' % fs_img)
for i in range(0, 20):
output = u_boot_console.run_command_list([
'%srm host 0:0 dir2/0123456789abcdef%02x' % (fs_type, i),
'%sls host 0:0 dir2/0123456789abcdef%02x' % (fs_type, i)])
assert('' == ''.join(output))
output = u_boot_console.run_command(
'%sls host 0:0 dir2' % fs_type)
> assert('0 file(s), 2 dir(s)' in output)
E AssertionError: assert '0 file(s), 2 dir(s)' in ' ./\r\r\n ../\r\r\n 0 0123456789abcdef11\r\r\n\r\r\n1 file(s), 2 dir(s)'
test/py/tests/test_fs/test_unlink.py:52: AssertionError
===>8===
This can happen when fat_itr_next() wrongly detects an already-
deleted directory entry.
File deletion, which was added in the commit f8240ce95d ("fs: fat:
support unlink"), is implemented by marking its entry for a short name
with DELETED_FLAG, but related entry slots for a long file name are kept
unmodified. (So entries will never be actually deleted from media.)
To handle this case correctly, an additional check for a directory slot
will be needed in fat_itr_next().
In addition, I added extra comments about long file name and short file
name format in FAT file system. Although they are not directly related
to the issue, I hope it will be helpful for better understandings
in general.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
These don't need to be in common.h so move them out into a new header.
Also add some missing comments.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Drop inclusion of crc.h in common.h and use the correct header directly
instead.
With this we can drop the conflicting definition in fw_env.h and rely on
the crc.h header, which is already included.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function is a variant of fs_get_type_name() and returns a filesystem
type with which the current device is associated.
We don't want to export fs_type variable directly because we have to take
care of it consistently within fs.c.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
fs_ls(), fs_mkdir() and fs_unlink() sets fs_type to FS_TYPE_ANY
explicitly, but it is redundant as they call fs_close().
So just remove those lines.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
fs_close() closes the connection to a file system which opened with
either fs_set_blk_dev() or fs_set_dev_with_part(). Many file system
functions implicitly call fs_close(), e.g. fs_closedir(), fs_exist(),
fs_ln(), fs_ls(), fs_mkdir(), fs_read(), fs_size(), fs_write()
and fs_unlink().
So just export it.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When hitting an invalid FAT cluster while reading a file always print an
error message and return an error code.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
File was found on specified location. Info about file was read,
but then immediately destroyed using 'free' call. As a result
file size was set to 0, hence fat process didn't read any data.
Premature 'free' call removed. Resources are freed right before
function return. File is read correctly.
Signed-off-by: Martin Vystrcil <martin.vystrcil@m-linux.cz>
Rename some camel-case variables to match U-Boot style.
Camel case is not generally allowed in U-Boot. Rename this variable to fit
in with the style.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Sometimes an image has multiple CBFS. The current CBFS API is limited to
handling only one at time. Also it keeps track of the CBFS internally in
BSS, which does not work before relocation, for example.
Add a few new functions to overcome these limitations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Move the result variable into the struct also, so that it can be used when
BSS is not available. Add a function to read it.
Note that all functions sill use the BSS version of the data.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
At present there are a number of static variables in BSS. This cannot work
with SPL, at least until BSS is available in board_init_r().
Move the variables into a struct, so it is possible to malloc() it and use
it before BSS is available.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
At present this file has a function at the top, above declarations. This
is normally avoided, so fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Add a new Kconfig option to enable CBFS in SPL. This can be useful when
the memory-init code is in CBFS.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Move env_set_hex() over to the new header file along with env_set_addr()
which uses it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
As part of the effort to remove things from common.h, create a new header
for the gzip functions. Move the function declarations to it and add
missing documentation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
In ext4fs_read_file in ext4fs.c, a memset can overwrite the bounds of
the destination memory region. This patch adds a check to disallow
this.
Signed-off-by: Paul Emge <paulemge@forallsecure.com>
This patch checks for 0 in several ext4 headers and gracefully
fails instead of raising a divide-by-0 exception.
Signed-off-by: Paul Emge <paulemge@forallsecure.com>
in ext4fs_read_file, it is possible for a broken/malicious file
system to cause a memcpy of a negative number of bytes, which
overflows all memory. This patch fixes the issue by checking for
a negative length.
Signed-off-by: Paul Emge <paulemge@forallsecure.com>
ext_cache_read doesn't null cache->buf, after freeing, which results
in a later function double-freeing it. This patch fixes
ext_cache_read to call ext_cache_fini instead of free.
Signed-off-by: Paul Emge <paulemge@forallsecure.com>
JOURNAL is optional for EXT4 (and EXT3) filesystems, so add support for
skipping it. This fixes corrupting EXT4 volumes without JOURNAL after
using uboot's 'ext4write' command.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
The block count entry in the EXT4 filesystem disk structures uses
standard 512-bytes units for most of the typical files. The only
exception are HUGE files, which use the filesystem block size, but those
are not supported by uboot's EXT4 implementation anyway. This patch fixes
the EXT4 code to use proper unit count for inode block count. This fixes
errors reported by fsck.ext4 on disks with non-standard (i.e. 4KiB, in
case of new flash drives) PHYSICAL block size after using 'ext4write'
uboot's command.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
fatload command can be used to load the EFI payload since EFI system
partition is always a FAT partition. Call into EFI code from do_load()
to set the device path from which the last binary was loaded. An EFI
application like grub2 can’t find its configuration file without the
device path set.
Since device path is now set in do_load() there is no need to set it
in do_load_wrapper() for the load command.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Contrary to fat12/16, fat32 can have root directory at any location
and its size can be expanded.
Without this patch, root directory won't grow properly and so we will
eventually fail to add files under root directory. Please note that this
can happen even if you delete many files as deleted directory entries
are not reclaimed but just marked as "deleted" under the current
implementation.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When a long name directory entry is created, multiple directory entries
may be occupied across a directory cluster boundary. Since only one
directory cluster is cached in a directory iterator, a first cluster must
be written back to device before switching over a second cluster.
Without this patch, some added files may be lost even if you don't see
any failures on write operation.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
With the commit below, fat now correctly handles a file read under
a non-cluster-aligned root directory of fat12/16.
Write operation should be fixed in the same manner.
Fixes: commit 9b18358dc0 ("fs: fat: fix reading non-cluster-aligned
root directory")
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Anssi Hannula <anssi.hannula@bitwise.fi>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
fat_itr_root() allocates fatbuf so we free it on the exit path, if
the function fails we should not free it, check the return value
and skip freeing if the function fails.
Signed-off-by: Andrew F. Davis <afd@ti.com>
This adds decompression support for Zstandard, which has been included
in Linux btrfs driver for some time.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
The btrfs implementation methods .ls(), .size() and .read() returns 1 on
failure, but the command handlers expect values <0 on failure.
For example if given a nonexistent path, the load command currently
returns success, and hush scripting does not work.
Fix this by setting return values of these methods to -1 instead of 1 on
failure.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Per Pierre this change shouldn't have been applied as it was superseded
by "fs: btrfs: fix btrfs_search_tree invalid results" which is also
applied now as 1627e5e598.
This reverts commit 633967f981.
Signed-off-by: Tom Rini <trini@konsulko.com>
btrfs_search_tree should return the first item in the tree that is
greater or equal to the searched item.
The search algorithm did not properly handle the edge case where the
searched item is higher than the last item of the node but lower than
the first item of the next node. Instead of properly returning the first
item of the next node, it was returning an invalid path pointer
(pointing to a non-existent item after the last item of the node + 1).
This fixes two issues in the btrfs driver:
- Looking for a ROOT_ITEM could fail if it was the first item of its
leaf node.
- Iterating through DIR_INDEX entries (for readdir) could fail if the
first DIR_INDEX entry was the first item of a leaf node.
Signed-off-by: Pierre Bourdon <delroth@gmail.com>
Cc: Marek Behun <marek.behun@nic.cz>
ROOT_ITEMs in btrfs are referenced without knowing their actual "offset"
value. To perform these searches using only two items from the key, the
btrfs driver uses a special "btrfs_search_tree_key_type" function.
The algorithm used by that function to transform a 3-tuple search into a
2-tuple search was subtly broken, leading to items not being found if
they were the first in their tree node.
This commit fixes btrfs_search_tree_key_type to properly behave in these
situations.
Signed-off-by: Pierre Bourdon <delroth@gmail.com>
Cc: Marek Behun <marek.behun@nic.cz>
Ext4 allows for arbitrarily sized block group descriptors when 64-bit
addressing is enabled, which was previously not properly supported. This
patch dynamically allocates a chunk of memory of the correct size.
Signed-off-by: Benjamin Lim <jarsp.ctf@gmail.com>
A FAT12/FAT16 root directory location is specified by a sector offset and
it might not start at a cluster boundary. It also resides before the
data area (before cluster 2).
However, the current code assumes that the root directory is located at
a beginning of a cluster, causing no files to be found if that is not
the case.
Since the FAT12/FAT16 root directory is located before the data area
and is not aligned to clusters, using unsigned cluster numbers to refer
to the root directory does not work well (the "cluster number" may be
negative, and even allowing it be signed would not make it properly
aligned).
Modify the code to not use the normal cluster numbering when referring to
the root directory of FAT12/FAT16 and instead use a cluster-sized
offsets counted from the root directory start sector.
This is a relatively common case as at least the filesystem formatter on
Win7 seems to create such filesystems by default on 2GB USB sticks when
"FAT" is selected (cluster size 64 sectors, rootdir size 32 sectors,
rootdir starts at half a cluster before cluster 2).
dosfstools mkfs.vfat does not seem to create affected filesystems.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Reviewed-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Tested-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Hi,
when I try to load a sparse file via ext4load, I am getting the error message
'invalid extent'
After a deeper look in the code, it seems to be an issue in the function ext4fs_get_extent_block in fs/ext4/ext4_common.c:
The file starts with 1k of zeros. The blocksize is 1024. So the first extend block contains the following information:
eh_entries: 1
eh_depth: 1
ei_block 1
When the upper layer (ext4fs_read_file) asks for fileblock 0, we are running in the 'invalid extent' error message.
For me it seems, that the code is not prepared for handling a sparse block at the beginning of the file. The following change, solved my problem:
I am really not an expert in ext4 filesystems. Can somebody please have a look at this issue and give me a feedback, if I am totally wrong or not?
The command line is:
ln <interface> <dev[:part]> target linkname
Currently symbolic links are supported only in ext4 and only if the option
CMD_EXT4_WRITE is enabled.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Re-use the functions used to write/create a file, to support creation of a
symbolic link.
The difference with a regular file are small:
- The inode mode is flagged with S_IFLNK instead of S_IFREG
- The ext2_dirent's filetype is FILETYPE_SYMLINK instead of FILETYPE_REG
- Instead of storing the content of a file in allocated blocks, the path
to the target is stored. And if the target's path is short enough, no block
is allocated and the target's path is stored in ext2_inode.b.symlink
As with regulars files, if a file/symlink with the same name exits, it is
unlinked first and then re-created.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Fix ext4 env code]
Signed-off-by: Tom Rini <trini@konsulko.com>
There is no need to modify the buffer passed to ext4fs_write_file().
The memset() call is not required here and was likely copied from the
equivalent part of the ext4fs_read_file() function where we do need it.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
When a file contains extents, U-Boot currently reads extent-related data
for each block in the file, even if that data is located in the same
block each time. This significantly slows down loading of files that use
extents. Implement a very dumb cache to prevent repeatedly reading the
same block. Files with extents now load as fast as files without.
Note: There are many cases where read_allocated_block() is called. This
patch only addresses one of those places; all others still read redundant
data in any case they did before. This is a minimal patch to fix the
load command; other cases aren't fixed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Before printk.h was introduced and MTDDEBUG was removed,
pr_crit() was calling MTDDEBUG(), which was since then
replaced by the current pr_debug().
pr_debug is more appropriate here.
Signed-off-by: Eran Matityahu <eran.m@variscite.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
U-Boot doesn't support metadata_csum feature. Writing to filesystem with
metadata_csum feature makes the filesystem corrupted and unbootable by
Linux:
[ 2.527495] EXT4-fs (mmcblk0p2): ext4_check_descriptors: Checksum for group 0 failed (52188!=0)
[ 2.537421] EXT4-fs (mmcblk0p2): ext4_check_descriptors: Checksum for group 1 failed (5262!=0)
...
[ 2.653308] EXT4-fs (mmcblk0p2): ext4_check_descriptors: Checksum for group 14 failed (42611!=0)
[ 2.662179] EXT4-fs (mmcblk0p2): ext4_check_descriptors: Checksum for group 15 failed (21527!=0)
[ 2.687920] JBD2: journal checksum error
[ 2.691982] EXT4-fs (mmcblk0p2): error loading journal
[ 2.698292] VFS: Cannot open root device "mmcblk0p2" or unknown-block(179,2): error -74
Don't write to filesystem with meatadata_csum feature to not corrupt the
filesystem.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
When compiling with DEBUG=1 an error
fs/fat/fat_write.c:831: undefined reference to `__aeabi_ldivmod'
occurred.
We should use do_div() instead of the modulus operator.
filesize and cur_pos cannot be negative. So let's use u64 to avoid
warnings.
Fixes: cb8af8af5b ("fs: fat: support write with non-zero offset")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Release cluster block immediately when no longer use would help to reduce
64KiB memory allocated to the memory pool.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Drop the statically allocated get_contents_vfatname_block and
dynamically allocate a buffer only if required. This saves
64KiB of memory.
Signed-off-by: Stefan Agner <stefan.ag...@toradex.com>
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Unlike other generic FS accessors, fs_get_info() does not call fs_close()
at the end of it's operation. Thus, using fs_get_info() in do_fs_type()
without calling fs_close() causes potential memory leak by creating new
filesystem structures on each call of do_fs_type().
The test case to trigger this problem is as follows. It is required to
have ext4 filesystem on the first partition of the SDMMC device, since
ext4 requires stateful mount and causes memory allocation.
=> while true ; do mmc rescan ; fstype mmc 1 ; done
Eventually, the mounting of ext4 will fail due to malloc failures
and the filesystem will not be correctly detected.
This patch fixes the problem by adding the missing fs_close().
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
This fixes the automatic lmb initialization and reservation for boards
with more than one DRAM bank.
This fixes the CVE-2018-18439 and -18440 fixes that only allowed to load
files into the firs DRAM bank from fs and via tftp.
Found-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
CONFIG_SPL_FS_EXT4 can be used to include/exclude the FS EXT4 from
SPL build. Excluding the FS EXT4 from SPL build can help to save 20KiB
memory.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Replace CONFIG_SPL_EXT_SUPPORT to CONFIG_SPLY_FS_EXT4 so both
obj-$(CONFIG_$(SPL_)FS_EXT4) and CONFIG_IS_ENABLED(FS_EXT4) can be
used to control the build in both SPL and U-Boot.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Most of the time SPL only needs very simple FAT reading, so having
CONFIG_IS_ENABLED(FAT_WRITE) to exclude it from SPL build would help
to save 64KiB default max clustersize from memory.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Replace CONFIG_SPL_FAT_SUPPORT with CONFIG_SPL_FS_FAT so
obj-$(CONFIG_$(SPL_)FS_FAT) can be used to control the build in both
SPL and U-Boot.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This fixes CVE-2018-18440 ("insufficient boundary checks in filesystem
image load") by using lmb to check the load size of a file against
reserved memory addresses.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This particular commit is causing a regression on stih410-b2260 and
other platforms when reading from FAT16. Noting that I had rebased the
original fix from Thomas onto then-current master, there is also
question from Akashi-san if the change is still needed after other FAT
fixes that have gone in.
This reverts commit a68b0e11ea.
Reported-by: Patrice Chotard <patrice.chotard@st.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Thomas RIENOESSL <thomas.rienoessl@bachmann.info>
Signed-off-by: Tom Rini <trini@konsulko.com>
The call to file_cbfs_fill_cache() is given with the parameter
'start' pointing to the offset by the CBFS base address, but
with the parameter 'size' that equals to the whole CBFS size.
During CBFS walking through, it checks files one by one and
after it pass over the end of the CBFS which is 4GiB boundary
it tries to check files from address 0 and so on, until the
overall size the codes checked hits to the given 'size'.
Fix this by passing 'start' pointing to the CBFS base address.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
cbfs_fileheader.len indicates the content size of the file in the
cbfs, and it has nothing to do with cbfs_fileheader.offset which
is the starting address of the file in the cbfs.
Remove such check in file_cbfs_next_file(). Before this change
'cbfsinit' failed with 'Bad CBFS file'. After this change all cbfs
commands are working as expected.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
[bmeng: keep the necessary header sanity check]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The long name apparently can be accumulated using multiple
13-byte slots. Unfortunately we never checked how many we
can actually fit in the buffer we are reading to.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
The cluster size specifies how many sectors make up a cluster. A
cluster size of zero makes no sense, as it would mean that the
cluster is made up of no sectors. This will later lead into a
division by zero in sect_to_clust(), so better take care of that
early.
The MAX_CLUSTSIZE define can reduced using a define to make some
room in low-memory system. Unfortunately if the code reads a
filesystem with a bigger cluster size it will overflow the buffer.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
As in the case of fs_set_blk_dev(), fs_set_blk_dev_with_part() should
maintain and update fs_dev_part whenever called.
Without this patch, a problem will come up when an efi binary associated
with efi's BOOTxxxx variable is invoked via "bootefi bootmgr".
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This fixes problems accessing drives formated under
Windows as FAT16.
Signed-off-by: Thomas RIENOESSL <thomas.rienoessl@bachmann.info>
[trini: Rebase on top of f528c140c8]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add fs.c under SPL as well as it is needed for fs_loader
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Add as obj-$(CONFIG_FS_LOADER) for non-SPL_FRAMEWORK builds]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add local size_t variable to crypto_comp_decompress as intermediate
storage for destination length to avoid memory corruption and incorrect
results on 64 bit targets.
This is what linux does for the various lz compression implementations.
Signed-off-by: Paul Davey <paul.davey@alliedtelesis.co.nz>
Cc: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
As observed with clang:
fs/fat/fat_write.c:1024:13: warning: comparison of constant 128
with expression of type 'char' is always false
[-Wtautological-constant-out-of-range-compare]
if ((0x80 <= c) && (c <= 0xff))
~~~~ ^ ~
fs/fat/fat_write.c:1024:25: warning: comparison of constant 255
with expression of type 'char' is always true
[-Wtautological-constant-out-of-range-compare]
if ((0x80 <= c) && (c <= 0xff))
~ ^ ~~~~
Fixes: 25bb9dab14 ("fs: fat: check and normalize file name")
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
When traversing slots in a btree (via btrfs_path) with btrfs_next_slot(),
we didn't correctly identify that the last slot in the leaf was reached
and we should jump to the next leaf.
This could lead to any kind of runtime errors or corruptions, like:
* file data not being read at all, or is read partially
* file is read but is corrupted
* (any) metadata being corrupted or not read at all, etc
The easiest way to reproduce this is to read a large enough file that
its EXTENT_DATA items don't fit into a single leaf.
Signed-off-by: Yevgeny Popovych <yevgenyp@pointgrab.com>
Cc: Marek Behun <marek.behun@nic.cz>
Tested-by: Marek Behún <marek.behun@nic.cz>
Avoid CoverityScan warning SIGN_EXTENSION by changing the type of
parameter size of set_cluster().
Avoid leaking stack content when writing an incomplete last sector.
Reported-by: Coverity (CID: 184096)
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Do not leak filename_copy in case of error.
Catch out of memory when calling strdup.
Reported-by: Coverity (CID: 184086)
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The btrfs implementation passes cache-unaligned buffers into the
block layer, which triggers cache alignment problems down in the
block device drivers. Align the buffers to prevent this.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Behun <marek.behun@nic.cz>
The FAT driver supports unaligned reads and writes and EFI applications
will make use of these. So a misaligned buffer is only worth a debug
message.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
In this patch, unlink support is added to FAT file system.
A directory can be deleted only if it is empty.
In this implementation, only a directory entry for a short file name
will be removed. So entries for a long file name can and should be
reclaimed with fsck.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
"unlink" interface is added to file operations.
This is a preparatory change as unlink support for FAT file system
will be added in next patch.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
In this patch, mkdir support is added to FAT file system.
A newly created directory contains only "." and ".." entries.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The starting cluster number of directory is needed to initialize ".."
(parent directory) entry when creating a new directory.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
"mkdir" interface is added to file operations.
This is a preparatory change as mkdir support for FAT file system
will be added in next patch.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
In this patch, all the necessary code for allowing for a file offset
at write is implemented. What plays a major roll here is get_set_cluster(),
which, in contrast to its counterpart, set_cluster(), only operates on
already-allocated clusters, overwriting with data.
So, with a file offset specified, set_contents() seeks and writes data
with set_get_cluster() until the end of a file, and, once it reaches
there, continues writing with set_cluster() for the rest.
Please note that a file will be trimmed as a result of write operation if
write ends before reaching file's end. This is an intended behavior
in order to maintain compatibility with the current interface.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The current write implementation is quite simple: remove existing clusters
and then allocating new ones and filling them with data. This, inevitably,
enforces always writing from the beginning of a file.
As the first step to lift this restriction, fat_file_write() and
set_contents() are modified to accept an additional parameter, file offset
and further re-factored so that, in the next patch, all the necessary code
will be put into set_contents().
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
In this patch, write implementation is overhauled and rewritten by
making full use of directory iterator. The obvious bonus is that we are
now able to write to a file with a directory path, like /A/B/C/FILE.
Please note that, as there is no notion of "current directory" on u-boot,
a file name specified must contain an absolute directory path. Otherwise,
"/" (root directory) is assumed.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
It would be good that FAT write function return error code instead of
just returning -1 as fat_read_file() does.
This patch attempts to address this issue although it is 'best effort
(or estimate)' for now.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
FAT file system's long file name support is a bit complicated and has some
restrictions on its naming. We should be careful about it especially for
write as it may easily end up with wrong file system.
normalize_longname() check for the rules and normalize a file name
if necessary. Please note, however, that this function is yet to be
extended to fully comply with the standard.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This reverts commit 0dc1bfb730.
The succeeding patch series will supersede it.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
In my attempt to re-work write operation, it was revealed that iterator's
"clust" does not always point to a cluster to which a current directory
entry ("dent") belongs.
This patch assures that it is always true by adding "next_clust" which is
used solely for dereferencing a cluster chain.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
FAT's root directory does not have "." nor ".."
So care must be taken when scanning root directory with fat_itr_resolve().
Without this patch, any file path starting with "." or ".." will not be
resolved at all.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
get_fs_info() was introduced in major re-work of read operation by Rob.
We want to reuse this function in write operation by extending it with
additional members in fsdata structure.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
I just stumbled over some cluttered UBIFS messages. It seems some
newline chars are missing in the current U-Boot UBI source.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
In int-ll64.h, we always use the following typedefs:
typedef unsigned int u32;
typedef unsigned long uintptr_t;
typedef unsigned long long u64;
This does not need to match to the compiler's <inttypes.h>.
Do not include it.
The use of PRI* makes the code super-ugly. You can simply use
"l" for printing uintptr_t, "ll" for u64, and no modifier for u32.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In order to make the debug print in file_fat_read_at() a tad more useful,
show the offset the file is being read at alongside the filename.
Suggested-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
fs_fat_write() is not able to write to subdirectories.
Currently if a filepath with a leading slash is passed, the slash is
treated as part of the filename to be created in the root directory.
Strip leading (back-)slashes.
Check that the remaining filename does not contain any illegal characters
(<>:"/\|?*). This way we will throw an error when trying to write to a
subdirectory.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The comparison
logical > item->logical + item->length
in btrfs_map_logical_to_physical is wrong and should be instead
logical >= item->logical + item->length
For example, if
item->logical = 4096
item->length = 4096
and we are looking for logical = 8192, it is not part of item (item is
[4096, 8191]). But the comparison is false and we think we have found
the correct item, although we should be searing in the right subtree.
This fixes some bugs I encountered.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
By checking ubifs source code, s_instances parameter is not
used anymore. So, set this parameter and the associated source
code under __UBOOT__ compilation.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This is the case when reading freshly created filesystem.
The error message is like the following:
btrfs_read_superblock: No valid root_backup found!
Since the data from super_roots/root_backups is not actually used -
decided to rework btrfs_newest_root_backup() into
btrfs_check_super_roots() that will only check if super_roots
array is valid and correctly handle empty scenario.
As a result:
* btrfs_read_superblock() now only checks if super_roots array is valid;
the case when it is empty is considered OK.
* removed root_backup pointer from btrfs_info,
which would be NULL in case of empty super_roots.
* btrfs_read_superblock() verifies number of devices from the superblock
itself, not newest root_backup.
Signed-off-by: Yevgeny Popovych <yevgenyp@pointgrab.com>
Cc: Marek Behun <marek.behun@nic.cz>
Cc: Sergey Struzh <sergeys@pointgrab.com>
This causes errors when translating logical addresses to physical:
btrfs_map_logical_to_physical: Cannot map logical address <addr> to physical
btrfs_file_read: Error reading extent
The behavior of btrfs_map_logical_to_physical() is to stop traversing
CHUNK_TREE when it encounters first non-CHUNK_ITEM, which makes
only some portion of CHUNK_ITEMs being read.
Change it to skip over non-chunk items.
Signed-off-by: Yevgeny Popovych <yevgenyp@pointgrab.com>
Cc: Marek Behun <marek.behun@nic.cz>
Cc: Sergey Struzh <sergeys@pointgrab.com>
Reviewed-by: Marek Behun <marek.behun@nic.cz>
Add fs_get_type_name so we can get the current filesystem type.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Found a crash while issuing ext4ls with a non-existent directory.
Crash test:
=> ext4ls mmc 0 1
** Can not find directory. **
data abort
pc : [<3fd7c2ec>] lr : [<3fd93ed8>]
reloc pc : [<26f142ec>] lr : [<26f2bed8>]
sp : 3f963338 ip : 3fdc3dc4 fp : 3fd6b370
r10: 00000004 r9 : 3f967ec0 r8 : 3f96db68
r7 : 3fdc99b4 r6 : 00000000 r5 : 3f96dc88 r4 : 3fdcbc8c
r3 : fffffffa r2 : 00000000 r1 : 3f96e0bc r0 : 00000002
Flags: nZCv IRQs off FIQs off Mode SVC_32
Resetting CPU ...
resetting ...
Tested on SAMA5D2_Xplained board (sama5d2_xplained_mmc_defconfig)
Looks like crash is introduced by commit:
"fa9ca8a" fs/ext4/ext4fs.c: Free dirnode in error path of ext4fs_ls
Issue is that dirnode is not initialized, and then freed if the call
to ext4_ls fails. ext4_ls will not change the value of dirnode in this case
thus we have a crash with data abort.
I added initialization and a check for dirname being NULL.
Fixes: "fa9ca8a" fs/ext4/ext4fs.c: Free dirnode in error path of ext4fs_ls
Cc: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch solves assert failed displayed in the console during a boot.
The root cause is that the ubifs_inode is not already allocated when
ubifs_printdir and ubifs_finddir functions are called.
Trace showing the issue:
feed 'boot.scr.uimg', ino 94, new f_pos 0x17b40ece
dent->ch.sqnum '7132', creat_sqnum 3886945402880
UBIFS assert failed in ubifs_finddir at 436
INODE ALLOCATION: creat_sqnum '7129'
Found U-Boot script /boot.scr.uimg
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
The mutex lock and unlock functions are stubbed out and mutex_is_locked
was 0. This caused asserts to fail in ubifs code when checking that the
mutex was locked. For example,
UBIFS assert failed in ubifs_change_lp at 540
UBIFS assert failed in ubifs_release_lprops at 278
Assume that the "mutex" is locked since that is the normal case when it
is checked in the ubifs code.
Signed-off-by: Bradley Bolen <bradleybolen@gmail.com>
Introduce another difference from upstream (kernel) source in
fs/ubifs/super.c: adding preprocessor condition as y variable in
mount_ubifs() depends on CONFIG_UBIFS_SILENCE_MSG:
fs/ubifs/super.c:1337:15: error: variable ?y? set but not used [-Werror=unused-but-set-variable]
long long x, y;
Not setting CONFIG_UBIFS_SILENCE_MSG in am335x_igep003x_defconfig and
igep0032_defconfig. Although it was defined in their config headers, it
depends on CMD_UBIFS which is not set for them.
Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Heiko Schocher <hs@denx.de>
Use of CONFIG_UBIFS_SILENCE_MSG was added in
147162dac6 ("ubi: ubifs: Turn off verbose prints")
Then it was removed in
ff94bc40af ("mtd, ubi, ubifs: resync with Linux-3.14")
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
When printing a size_t value we need to use %zu for portability between
32bit and 64bit targets.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Behun <marek.behun@nic.cz>
Loading files stored with lzo compression from a btrfs filesystem was
producing unaligned memory accesses, which were causing a data abort
and a reset on an Orange Pi Zero.
The change in hash.c is not triggered by any error but follows the
same pattern. Please confirm.
Fixed according to doc/README.unaligned-memory-access.txt
Signed-off-by: Alberto Sánchez Molero <alsamolero@gmail.com>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
fat.h unconditionally defines CONFIG_SUPPORT_VFAT (and has done since
2003), so as a result VFAT support is always enabled regardless of
whether a board config defines it or not. Drop this unnecessary option.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Migrate the following symbols to Kconfig:
CONFIG_FS_EXT4
CONFIG_EXT4_WRITE
The definitions in config_fallbacks.h can now be expressed in Kconfig.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
The message "reading %s\n" may be interesting when
debugging but otherwise it is superfluous.
Only output the message when debugging.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The message
"** %s shorter than offset + len **\n"
may be interesting when debugging but it does not indicate an
error.
So we should not write it if we are not in debug mode.
Fixes: 7a3e70cfd8 fs/fs.c: read up to EOF when len would read past EOF
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
commit 21a24c3bf3 ("fs/fat: fix case for FAT shortnames") made it
possible that get_name() returns file names with some upper cases.
find_directory_entry() must be updated to take this account, and use
case-insensitive functions to compare file names.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This header was renamed to rawnand.h in Linux.
The following is the corresponding commit in Linux.
commit d4092d76a4a4e57b65910899948a83cc8646c5a5
Author: Boris Brezillon <boris.brezillon@free-electrons.com>
Date: Fri Aug 4 17:29:10 2017 +0200
mtd: nand: Rename nand.h into rawnand.h
We are planning to share more code between different NAND based
devices (SPI NAND, OneNAND and raw NANDs), but before doing that
we need to move the existing include/linux/mtd/nand.h file into
include/linux/mtd/rawnand.h so we can later create a nand.h header
containing all common structure and function prototypes.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Before this patch one could receive following errors when executing "fatls"
command on machine with cache enabled (ex i.MX6Q) :
=> fatls mmc 0:1
CACHE: Misaligned operation at range [4f59dfc8, 4f59e7c8]
CACHE: Misaligned operation at range [4f59dfc8, 4f59e7c8]
ERROR: v7_outer_cache_inval_range - start address is not aligned - 0x4f59dfc8
ERROR: v7_outer_cache_inval_range - stop address is not aligned - 0x4f59e7c8
CACHE: Misaligned operation at range [4f59dfc8, 4f59e7c8]
CACHE: Misaligned operation at range [4f59dfc8, 4f59e7c8]
ERROR: v7_outer_cache_inval_range - start address is not aligned - 0x4f59dfc8
ERROR: v7_outer_cache_inval_range - stop address is not aligned - 0x4f59e7c8
To alleviate this problem - the calloc()s have been replaced with
malloc_cache_aligned() and memset().
After those changes the buffers are properly aligned (with both start
address and size) to SoC cache line.
Fixes: 09fa964bba ("fs/fat: Fix 'CACHE: Misaligned operation at range' warnings")
Suggested-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
It is unwise to first dereference a variable
and then to check if it was NULL.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The iterator variable of list_for_each is never NULL.
if (1 || A) is always true.
Use break if entry found.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Some fixes when reading EXT files and directory entries were identified
after using e2fuzz to corrupt an EXT3 filesystem:
- Stop reading directory entries if the offset becomes badly aligned.
- Avoid overwriting memory by clamping the length used to zero the buffer
in ext4fs_read_file. Also sanity check blocksize.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Reviewed-by: Stefano Babic <sbabic@denx.de>
All users of this macro have been converted. Remove MTDDEBUG and
related CONFIG options.
ubifs_dbg_msg_key() is kept. It is silent unless DEBUG is defined.
I am not touching scripts/config_whitelist.txt. The deprecated options
will be dropped by the next resync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This makes gcc no longer expect an out-of-line version of the
functions being present elsewhere.
This fixes a failure to build on several marvell targets with gcc-7 on
Debian:
https://bugs.debian.org/877963
Signed-off-by: Adrian Bunk <bunk@debian.org>
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Hello,
I ran into a problem with the JFFS2 filesystem driver implemented in U-Boot.
I've got a NAND device that has correctable ECC errors (corrected somewhere in mtd/nand/nand_base.c).
The NAND driver tells the filesystem layer (jffs2_1pass.c) above that there occurred correctable ECC errors and returns with a "value > 0".
The JFFS2 driver recognizes the corrected ECC errors as real error and skips this block because the only accepts a "return value == 0" as correct.
This problem exists for over 8 years (I checked version 2010.09) so I'm a little bit worried that I interpreted something wrong or didn't get the whole context.
Can someone confirm this bug (and the bugfix) in the u-boot jffs2 driver?
There was a mail in 2012 that mentioned the same problem, but there was no patch:
http://u-boot.10912.n7.nabble.com/JFFS2-seems-to-drop-nand-data-with-ECC-corrections-td142008.html
Sometime after this discussion the return value of nand_read() changed from -EUCLEAN as correctable ECC error to a positive value with the count of ECC corrected errors.
With kind reguards,
Uwe Engling
The variable res should be initialized to 0 in these functions,
because if the searched key is not found, the variable is used
uninitialized.
Reported-by: Coverity (CID: 167335)
Reported-by: Coverity (CID: 167336)
Reported-by: Coverity (CID: 167337)
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Check malloc() return values and properly unwind on errors so
memory allocated for fat_itr structures get freed properly.
Also fixes a leak of fsdata.fatbuf in fat_size().
Fixes: 2460098cff ("fs/fat: Reduce stack usage")
Reported-by: Coverity (CID: 167225, 167233, 167234)
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Tom Rini <trini@konsulko.com>
The 'block' field of fat_itr needs to be properly aligned for DMA and
while it does have '__aligned(ARCH_DMA_MINALIGN)', the fat_itr structure
itself needs to be properly aligned as well.
While at it use malloc_cache_aligned() for the other aligned allocations
in the file as well.
Fixes: 2460098cff ("fs/fat: Reduce stack usage")
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Tom Rini <trini@konsulko.com>
As reported by Coverity, we did not free dirnode in the case of failure.
Do so now.
Reported-by: Coverity (CID: 131221)
Cc: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
If we end up back in the root directory via a '..' directory entry, set
itr->is_root accordingly. Failing to do that gives spews like
"Invalid FAT entry" and being unable to access directory entries located
past the first cluster of the root directory.
Fixes: 8eafae209c ("fat/fs: convert to directory iterators")
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
The current code doesn't compute the group descriptor checksum correctly
for the filesystems that e2fsprogs 1.43.4 creates (they have
'Group descriptor size: 64' as reported by tune2fs). Extend the checksum
calculation to be done as ext4_group_desc_csum() does in Linux.
This fixes these errors in dmesg from running fs-test.sh and makes it
succeed again:
[1671902.620699] EXT4-fs (loop1): ext4_check_descriptors: Checksum for group 0 failed (35782!=10965)
[1671902.620706] EXT4-fs (loop1): group descriptors corrupted!
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
U-Boot widely uses error() as a bit noisier variant of printf().
This macro causes name conflict with the following line in
include/linux/compiler-gcc.h:
# define __compiletime_error(message) __attribute__((error(message)))
This prevents us from using __compiletime_error(), and makes it
difficult to fully sync BUILD_BUG macros with Linux. (Notice
Linux's BUILD_BUG_ON_MSG is implemented by using compiletime_assert().)
Let's convert error() into now treewide-available pr_err().
Done with the help of Coccinelle, excluing tools/ directory.
The semantic patch I used is as follows:
// <smpl>
@@@@
-error
+pr_err
(...)
// </smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Re-run Coccinelle]
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds the proper implementation for the BTRFS filesystem.
The implementation currently supports only read-only mode and
the filesystem can be only on a single device.
Checksums of data chunks is unimplemented.
Compression is implemented (ZLIB + LZO).
Signed-off-by: Marek Behun <marek.behun@nic.cz>
create mode 100644 fs/btrfs/btrfs.h
create mode 100644 fs/btrfs/chunk-map.c
create mode 100644 fs/btrfs/compression.c
create mode 100644 fs/btrfs/ctree.c
create mode 100644 fs/btrfs/dev.c
create mode 100644 fs/btrfs/dir-item.c
create mode 100644 fs/btrfs/extent-io.c
create mode 100644 fs/btrfs/hash.c
create mode 100644 fs/btrfs/inode.c
create mode 100644 fs/btrfs/root.c
create mode 100644 fs/btrfs/subvolume.c
create mode 100644 fs/btrfs/super.c
BTRFS on disk structures are stored in Little Endian. Add functions
to convert this structures to cpu and to disk format.
On Little Endian hosts, these functions do nothing.
On Big Endian the CALL_MACRO_FROM_EACH from variadic-macro.h is used
to define all the members for each structure on which cpu_to_le* or
le*_to_cpu is to be called.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
create mode 100644 fs/btrfs/conv-funcs.h
Add btrfs_tree.h and ctree.h from Linux which contains constants
and structures for the BTRFS filesystem.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
create mode 100644 fs/btrfs/btrfs_tree.h
create mode 100644 fs/btrfs/ctree.h
The ext4, reiserfs and zfs filesystems all have their own implementation
of the same function, *_devread. Generalize this function into fs_devread
and put the code into fs/fs_internal.c.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
[trini: Move fs/fs_internal.o hunk to the end of fs/Makefile as all
cases need it]
Signed-off-by: Tom Rini <trini@konsulko.com>
We have limited stack in SPL builds. Drop itrblock and move to
malloc/free of itr to move this off of the stack. As part of this fix a
double-free issue in fat_size().
Signed-off-by: Tom Rini <trini@konsulko.com>
---
Rework to use malloc/free as moving this to a global overflows some SH
targets.
A new fatbuf was allocated by get_fs_info() (called by fat_itr_root()),
but not freed, resulting in eventually running out of memory. Spotted
by running 'ls -r' in a large FAT filesystem from Shell.efi.
fatbuf is mainly used to cache FAT entry lookups (get_fatent())..
possibly once fat_write.c it can move into the iterator to simplify
this.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Use the clust_to_sect() helper that was introduced earlier, and add an
inverse sect_to_clust(), plus update the various spots that open-coded
this conversion previously.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Noticed when comparing our output to linux. There are some lcase bits
which control whether filename and/or extension should be downcase'd.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a generic implementation of 'ls' using opendir/readdir/closedir, and
replace fat's custom implementation. Other filesystems should move to
the generic implementation after they add opendir/readdir/closedir
support.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Spotted by chance, when trying to remove file_fat_ls(), I noticed there
were some dead users of the API.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Acked-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Implement the readdir interface using the directory iterators.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Needed to support efi file protocol. The fallback.efi loader wants
to be able to read the contents of the /EFI directory to find an OS
to boot.
Modelled after POSIX opendir()/readdir()/closedir(). Unlike the other
fs APIs, this is stateful (ie. state is held in the FS_DIR "directory
stream"), to avoid re-traversing of the directory structure at each
step. The directory stream must be released with closedir() when it
is no longer needed.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
And drop a whole lot of ugly code!
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Untangle directory traversal into a simple iterator, to replace the
existing multi-purpose do_fat_read_at() + get_dentfromdir().
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Want to re-use this in fat dirent iterator in next patch.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
While &p_jdb[fs->blksz] is a valid expression (it points *one* char
sized element past the end of the array, e.g. &p_jdb[fs->blksz + 1] is
invalid (according to the C standard (C99/C11)).
Changing this to tag = (struct ext3_journal_block_tag *)(p_jdb + ofs);
Cc: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Suggested-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reported-by: Coverity (CID: 165117, 165110)
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
The overflow calculation was incorrect. Adding the start block of the
partition is not needed because the sectors are already relative to the
beginning of the partition. If you attempted to write a file smaller
than cur_part_info.start blocks on a full partition the old calculation
fails to catch the overflow. This would cause an infinite loop in the
determine_fatent function.
Old, incorrect calculation:
ending sector of new file = start sector + file size (in sectors)
last sector = partition start + total sectors on the partition
Adding the partition start block number is not needed because sectors
are already relative to the start of the partition.
New calculation:
ending sector of new file = start sector + file size (in sectors)
last sector = total sectors on the partition
Signed-off-by: Reno Farnesi <nfarnesi4@gmail.com>
The function blk_dread will return -ENOSYS on failure or on success the
number of blocks read, which must be the number asked to read (otherwise
it failed somewhere). Correct this check.
Signed-off-by: Tom Rini <trini@konsulko.com>
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.
Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
We are now using an env_ prefix for environment functions. Rename these
commonly used functions, for consistency. Also add function comments in
common.h.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
We are now using an env_ prefix for environment functions. Rename setenv()
for consistency. Also add function comments in common.h.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_CMD_YAFFS2
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
As part of preparation for nand DM conversion the new API has been
introduced to remove direct access to nand_info array. So, use it here
instead of accessing to nand_info array directly.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
At present CONFIG_CMD_SATA enables the 'sata' command which also brings
in SATA support. Some boards may wish to enable SATA without the command.
Add a separate CONFIG to permit this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch fixes the below warning by typecasting it properly
fs/ubifs/ubifs.c: In function 'ubifs_load':
fs/ubifs/ubifs.c:942:29: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
err = ubifs_read(filename, (void *)addr, 0, size, &actread);
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add Kconfig symbols for various configurations
supported by FAT filesystem support code.
CONFIG_SUPPORT_VFAT has been left out since its
force enabled in include/fat.h and probably
should get removed at some point.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
[trini: add select FS_FAT for CMD_FAT and SPL_FAT_SUPPORT]
Signed-off-by: Tom Rini <trini@konsulko.com>
Rather than using CMD_JFFS2 for both the filesystem and its command, we
should have a separate option for each. This allows us to enable JFFS2
support without the command, if desired, which reduces U-Boot's size
slightly.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present IDE support is controlled by CONFIG_CMD_IDE. Add a separate
CONFIG_IDE option so that IDE support can be enabled without requiring
the 'ide' command.
Update existing users and move the ide driver into drivers/block since
it should not be in common/.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than using CMD_CRAMFS for both the filesystem and its command, we
should have a separate option for each. This allows us to enable CRAMFS
support without the command, if desired, which reduces U-Boot's size
slightly.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: imply FS_CRAMFS for keymile]
Signed-off-by: Tom Rini <trini@konsulko.com>
Rather than using CMD_CBFS for both the filesystem and its command, we
should have a separate option for each. This allows us to enable CBFS
support without the command, if desired, which reduces U-Boot's size
slightly.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: imply FS_CBFS on SYS_COREBOOT]
Signed-off-by: Tom Rini <trini@konsulko.com>
In file ext4fs.c funtion ext4fs_read_file() compares an
unsigned expression with < 0 like below
lbaint_t blknr;
blknr = read_allocated_block(&(node->inode), i);
if (blknr < 0)
return -1;
blknr is of type ulong/uint64_t. read_allocated_block() returns
long int. So comparing blknr with < 0 will always be false. Instead
declare blknr as long int.
Similarly ext4/dev.c does a similar comparison. Drop the redundant
comparison.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
If !parent, the changed line is not reached.
So there is no need to check the value again.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Handle symlinks to files in the current directory. Other cases could be
handled with additional code, but this is a start.
Add explicit errors for absolute paths and links found in the middle of
a path (directories). Other cases like '..' or '.' will result with the
file not being found as when those path components are explicitly
provided.
Add a helper to decompress a null-terminated link name which is shared
with cramfs_list_inode.
Signed-off-by: Tyler Hall <tylerwhall@gmail.com>
Using a variably-sized type is incorrect here since we're reading a
fixed file format. Fixes cramfs on 64-bit platforms.
Signed-off-by: Tyler Hall <tylerwhall@gmail.com>
We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is
not completed. Finish this work by the tool.
During this move, let's rename it to CONFIG_MTD_NOR_FLASH.
Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH"
than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will
make the code more readable. Besides, negative meaning symbols do
not fit in obj-$(CONFIG_...) style Makefiles.
This commit was created as follows:
[1] Edit "default n" to "default y" in the config entry in
common/Kconfig.
[2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH"
[3] Rename the instances in defconfigs by the following:
find . -path './configs/*_defconfig' | xargs sed -i \
-e '/CONFIG_SYS_NO_FLASH=y/d' \
-e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/'
[4] Change the conditionals by the following:
find . -name '*.[ch]' | xargs sed -i \
-e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \
-e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \
-e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \
-e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/'
[5] Modify the following manually
- Rename the rest of instances
- Remove the description from README
- Create the new Kconfig entry in drivers/mtd/Kconfig
- Remove the old Kconfig entry from common/Kconfig
- Remove the garbage comments from include/configs/*.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Doing unaligned reads is not supported on all architectures, use
byte sized reads of the little endian buffer.
Rename off16 to off8, as it reflects the buffer offset in byte
granularity (offset is in entry, i.e. 12 bit, granularity).
Fix a regression introduced in 8d48c92b45
Reported-by: Oleksandr Tymoshenko <gonzo@bluezbox.com>
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Tested-by: Oleksandr Tymoshenko <gonzo@bluezbox.com>
We convert CONFIG_PARTITION_UUIDS to Kconfig first. But in order to cleanly
update all of the config files we must also update CMD_PART and CMD_GPT to also
be in Kconfig in order to avoid complex logic elsewhere to update all of the
config files.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
genext2fs creates revision level 0 filesystems, which are not readable
by u-boot due to the initialized group descriptor size field.
f798b1dda1
Reported-by: Kever Yang <kever.yang@rock-chips.com>
Reported-by: FrostyBytes@protonmail.com
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Instead of shuffling bits from two adjacent 16 bit words, use one 16 bit
word with the appropriate byte offset in the buffer.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
get_fatent_value(...) flushes changed FAT entries to disk when fetching
the next FAT blocks, in every other aspect it is identical to
get_fatent(...).
Provide a stub implementation for flush_dirty_fat_buffer if
CONFIG_FAT_WRITE is not set. Calling flush_dirty_fat_buffer during read
only operation is fine as it checks if any buffers needs flushing.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
