Booting Agilex and Stratix 10 with ATF support.
SPL now loads ATF (BL31), U-Boot proper and DTB from FIT
image. The new boot flow with ATF support is as follow:
SPL -> ATF (BL31) -> U-Boot proper -> OS (Linux)
U-Boot proper now starts at 0x200000 (CONFIG_SYS_TEXT_BASE).
ATF will occupy the address range starting from 0x1000.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Add binman node to device tree to generate the FIT image for u-boot
(u-boot.itb) and OS kernel (kernel.itb).
u-boot.itb contains arm trusted firmware (ATF), u-boot proper and
u-boot device tree for ATF u-boot flow.
kernel.itb contains Linux Image and Linux device tree.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
SPL already setup the Clock Manager with the handoff data
from OCRAM. When the Clock Manager's driver get probed again
in SSBL, it shall skip the handoff data access in OCRAM.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Since SSBL is running in DRAM, it shall setup the stack in DRAM
instead of OCRAM which is occupied by SPL and handoff data.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
In non-secure mode (EL2), FPGA reconfiguration driver calls the
SMC/PSCI services provided by ATF to configure the FPGA.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
In non-secure mode (EL2), Reset Manager driver calls the
SMC/PSCI service provided by ATF to enable/disable the
SOCFPGA bridges.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
In non-secure mode (EL2), MAC driver calls the SMC/PSCI services
provided by ATF to setup the PHY interface.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
In non-secure mode (EL2), MMC driver calls the SMC/PSCI services
provided by ATF to set SDMMC's DRVSEL and SMPLSEL.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Change 'clksel' callback function to allow the code to return a
status.
This patch is a preparation for enabling Arm-Trusted-Firmware (ATF)
in Intel SoC FPGA. This patch does not change functionality.
When using Arm-Trusted-Firmware (ATF) in Intel SoC FPGA, the MMC clock
related register is secure register which is required to be written
via SMC/PCSI call. It is possible that U-Boot fail to write the
register if there is unexpected error between U-Boot and ATF.
As a result, there maybe signal integrity on MMC connection due to
clock. So, the code should reports error to user when 'clksel' fail.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
This header file defines the Secure Monitor Call (SMC) message
protocol for ATF (BL31) PSCI runtime services. It includes all
the PSCI SiP function identifiers for the secure runtime services
provided by ATF. The secure runtime services include System Manager's
registers access, 2nd phase bitstream FPGA reconfiguration, Remote
System Update (RSU) and etc.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
invoke_smc() allow U-Boot proper running in non-secure mode (EL2)
to invoke SMC call to ATF's PSCI runtime services such as
System Manager's registers access, 2nd phase bitstream FPGA
reconfiguration, Remote System Update (RSU) and etc.
smc_send_mailbox() is a send mailbox command helper function which invokes
the ATF's PSCI runtime service (function ID: INTEL_SIP_SMC_MBOX_SEND_CMD)
to send mailbox messages to Secure Device Manager (SDM).
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Standard PSCI function "CPU_ON" provided by ATF is now used
by Linux kernel to bring up the secondary CPUs to enable SMP
booting in Linux on SoC 64bits platform.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Override 'lowlevel_init' to make sure secondary CPUs trapped
in ATF instead of SPL. After ATF is initialized, it will signal
the secondary CPUs to jump from SPL to ATF waiting to be 'activated'
by Linux OS via PSCI call.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Instead of loading u-boot proper image (u-boot.img), SPL
now loads FIT image (u-boot.itb) which includes u-boot
proper, ATF and u-boot proper's DTB.
For OS, u-boot now loads FIT images (kernel.itb) which
includes Linux Image and Linux's DTB.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Add board_fit_config_name_match() for matching board name with
device tree files in FIT image. This will ensure correct DTB
file is loaded for different board type. Currently, we are not
supporting multiple device tree files in FIT image therefore this
function basically do nothing for now.
Users are allowed to override this 'weak' function in their
specific board implementation.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
- Update MAINTAINERS emails for STI and STM32
- Activate OF_LIVE for ST stm32mp15 boards
- Switch to MCO2 for PHY 50 MHz clock for DHCOM boards
- Correction in stm32prog command on uart: always flush DFU on start command
- Update USB-C power detection algorithm on DK boards
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl/+yLkACgkQ4rK92eCq
k3X/Fgf/d/11WyQrVzvpr+nN+4Wl7J+ASmoUz0yKa6ri+lbvhLgh+JXbCRKgRPWu
vNnI07pSoX/QeaMpGBU8Ztg/Onb9/pvffz4WMk1411GoyCpDFuuK3cVSIoqkPfu+
XmgSX0u4BXtve1+ZdWfVBWXawUSEDMmGR3tmz1708c/s/oYpnVeRDcqiqzJ94cWE
yt+SpMPVqMUVQ/rAGkE8ToSMxX7FusEa7SvCg4U2ikoRWs3kPpr/73+tRWlmgGxL
sW8SXSKiOmFyheSBx3d2B9n00kDYTTrQmbW9hlMilZmji7CwZYxgTCMdX0x4DeFP
RDajT2Yju1JmeM+Z8+Ke2tupzvy6QA==
=oK8C
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20210113' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Enable logging features for stm32mp15 boards
- Update MAINTAINERS emails for STI and STM32
- Activate OF_LIVE for ST stm32mp15 boards
- Switch to MCO2 for PHY 50 MHz clock for DHCOM boards
- Correction in stm32prog command on uart: always flush DFU on start command
- Update USB-C power detection algorithm on DK boards
A previous series already update STMicroelectronics emails maintainers
but some files have been omitted (Makefile, .dts, .dtsi and .rst files).
Update Patrick and my email address with the one dedicated to upstream
activities.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Remove the test on data->dfu_seq, because dfu_seq=0 not only when
the DFU is not started (mask with 0xffff). This flush is mandatory
as the final treatment, common with USB, is done in DFU callback.
This patch avoids issue if the received length is a multiple of
the DFU packet.
For example if size of bootfs partition is egual to 0x4000000,
data->dfu_seq=0 at the end of the partition, the flush it not
requested and the phase is not increased in the callback.
U-Boot continue to request the bootfs in the next GetPhase command.
Fixes: 468f0508b5 ("stm32mp: stm32prog: add serial link support")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Activate the live DT to reduce the DT parsing time.
For example the boot time is reduced by 200ms on STM32MP157C-EV1 board
for stm32mp15_basic_defconfig (boot with SPL) or
stm32mp15_trusted_defconfig (boot with TF-A).
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The LAN8710i PHY currently uses 50 MHz clock direct from PLL4P.
To permit PLL4P to run at faster frequency, use MCO2 as a divider.
The PLL4P runs at 100 MHz, supplies MCO2 which divides it by 2 to
50MHz, and supplies the PHY with 50 MHz via pin PG2. The feedback
clock are fed back in via pin PA1.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Change-Id: Ia9bf7119785d49b633a3ae761c3dc4a30b92628a
There shouldn't be a need to use loadables propertyn because u-boot can be
pointed by firmware property. This change should also speedup boot process
because loadables property is list of strings which code is going through.
On the other hand firmware can just point to one image.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
USB-C power supply which are Power Delivery compliant (USB-PD) are able
to provide different voltage/current (for example 5V/3A 9V/3A 12V/2.25A...)
In this case, the power supply need to negotiate the voltage/current to
use with the device using CC1/CC2 USB-C signals.
If this negotiation occurs during ADC measurement (done also on CC1/CC2
USB-C signals) some ADC acquisition can be corrupted which cause wrong
power supply current detection.
To avoid this, the power supply current detection algorithm is updated
as following:
- perform an ADC measurement, if a 3A current is detected, continue the
boot process.
- else, wait 20ms (max tPDDebounce duration) to ensure that USB-PD
negotiation is done and perform another ADC measurement.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Activate the logging features in SPL and U-Boot
(CONFIG_LOG and CONFIG_SPL_LOG) and the command 'log' with
CONFIG_CMD_LOG.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change pr_* to dev_ or log_ macro and define LOG_CATEGORY.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change pr_* to dev_ or log_ macro and define LOG_CATEGORY.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change pr_* to dev_ or log_ macro and define LOG_CATEGORY.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change pr_* to dev_ or log_ macro and define LOG_CATEGORY.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change pr_* to dev_ or log_ macro and define LOG_CATEGORY.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change pr_* to dev_ or log_ macro and define LOG_CATEGORY.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change debug/pr_* to log_* or dev_* macro and define LOG_CATEGORY.
Remove the "%s:" __func__ header as it is managed by dev macro
(dev->name is displayed) or log macro (CONFIG_LOGF_FUNC).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change debug/pr_debug to log_debug or dev_dbg macro and
define LOG_CATEGORY.
Remove the "%s:" __func__ header as it is managed by dev macro
(dev->name is displayed) or log macro (CONFIG_LOGF_FUNC).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change pr_debug to log_debug or dev_dbg macro and define LOG_CATEGORY.
Remove the "%s:" __func__ header as it is managed by dev macro
(dev->name is displayed) or log macro (CONFIG_LOGF_FUNC).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change debug to dev_dbg macro and define LOG_CATEGORY.
Remove the "%s:" __func__ header as it is managed by dev macro
(dev->name is displayed) or log macro (CONFIG_LOGF_FUNC).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Change debug to dev_dbg macro and define LOG_CATEGORY.
Remove the "%s:" __func__ header as it is managed by dev macro
(dev->name is displayed) or log macro (CONFIG_LOGF_FUNC).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change debug to dev_dbg macro and define LOG_CATEGORY.
Remove the "%s:" __func__ header as it is managed by dev macro
(dev->name is displayed).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change debug and pr_ macro to dev macro and define LOG_CATEGORY.
Remove the "%s:" __func__ header as it is managed by dev macro
(dev->name is displayed) or log macro (CONFIG_LOGF_FUNC).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change debug and pr_ macro to dev macro and define LOG_CATEGORY.
Remove the "%s:" __func__ header as it is managed by dev macro
(dev->name is displayed) or log macro (CONFIG_LOGF_FUNC).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change debug and pr_ macro to dev macro and define LOG_CATEGORY.
Remove the "%s:" __func__ header as it is managed by dev macro
(dev->name is displayed) or log macro (CONFIG_LOGF_FUNC).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change debug and pr_err to dev macro and define LOG_CATEGORY.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change debug and pr_err to dev macro and define LOG_CATEGORY.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
