Commit graph

208 commits

Author SHA1 Message Date
York Sun
eb53941206 powerpc/mpc85xx: software workaround for DDR erratum A-004468
Boot space translation utilizes the pre-translation address to select
the DDR controller target. However, the post-translation address will be
presented to the selected DDR controller. It is possible that the pre-
translation address selects one DDR controller but the post-translation
address exists in a different DDR controller when using certain DDR
controller interleaving modes. The device may fail to boot under these
circumstances. Note that a DDR MSE error will not be detected since DDR
controller bounds registers are programmed to be the same when configured
for DDR controller interleaving.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 14:31:28 -05:00
York Sun
57495e4e5e powerpc/mpc8xxx: Update DDR registers
DDRC ver 4.7 adds DDR_SLOW bit in sdram_cfg_2 register. This bit needs to be
set for speed lower than 1250MT/s.

CDR1 and CDR2 are control driver registers. ODT termination valueis for
IOs are defined. Starting from DDRC 4.7, the decoding of ODT for IOs is
	000 -> Termsel off
	001 -> 120 Ohm
	010 -> 180 Ohm
	011 -> 75 Ohm
	100 -> 110 Ohm
	101 -> 60 Ohm
	110 -> 70 Ohm
	111 -> 47 Ohm

Add two write leveling registers. Each QDS now has its own write leveling
start value. In case of zero value, the value of QDS0 will be used. These
values are board-specific and are set in board files.

Extend DDR register timing_cfg_1 to have 4 bits for each field.

DDR control driver registers and write leveling registers are added to
interactive debugging for easy access.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 14:31:26 -05:00
Roy Zang
111fd19e3b fm/mEMAC: add mEMAC frame work
The multirate ethernet media access controller (mEMAC) interfaces to
10Gbps and below Ethernet/IEEE 802.3 networks via either RGMII/RMII
interfaces or XAUI/XFI/SGMII/QSGMII using the high-speed SerDes interface.

Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 14:31:25 -05:00
York Sun
d2404141f9 powerpc/mpc85xx: Add B4860 and variant SoCs
Add support for Freescale B4860 and variant SoCs. Features of B4860 are
(incomplete list):

Six fully-programmable StarCore SC3900 FVP subsystems, divided into three
    clusters-each core runs up to 1.2 GHz, with an architecture highly
    optimized for wireless base station applications
Four dual-thread e6500 Power Architecture processors organized in one
    cluster-each core runs up to 1.8 GHz
Two DDR3/3L controllers for high-speed, industry-standard memory interface
    each runs at up to 1866.67 MHz
MAPLE-B3 hardware acceleration-for forward error correction schemes
    including Turbo or Viterbi decoding, Turbo encoding and rate matching,
    MIMO MMSE equalization scheme, matrix operations, CRC insertion and
    check, DFT/iDFT and FFT/iFFT calculations, PUSCH/PDSCH acceleration,
    and UMTS chip rate acceleration
CoreNet fabric that fully supports coherency using MESI protocol between
    the e6500 cores, SC3900 FVP cores, memories and external interfaces.
    CoreNet fabric interconnect runs at 667 MHz and supports coherent and
    non-coherent out of order transactions with prioritization and
    bandwidth allocation amongst CoreNet endpoints.
Data Path Acceleration Architecture, which includes the following:
  Frame Manager (FMan), which supports in-line packet parsing and general
    classification to enable policing and QoS-based packet distribution
  Queue Manager (QMan) and Buffer Manager (BMan), which allow offloading
    of queue management, task management, load distribution, flow ordering,
    buffer management, and allocation tasks from the cores
  Security engine (SEC 5.3)-crypto-acceleration for protocols such as
    IPsec, SSL, and 802.16
  RapidIO manager (RMAN) - Support SRIO types 8, 9, 10, and 11 (inbound and
    outbound). Supports types 5, 6 (outbound only)
Large internal cache memory with snooping and stashing capabilities for
    bandwidth saving and high utilization of processor elements. The
    9856-Kbyte internal memory space includes the following:
  32 Kbyte L1 ICache per e6500/SC3900 core
  32 Kbyte L1 DCache per e6500/SC3900 core
  2048 Kbyte unified L2 cache for each SC3900 FVP cluster
  2048 Kbyte unified L2 cache for the e6500 cluster
  Two 512 Kbyte shared L3 CoreNet platform caches (CPC)
Sixteen 10-GHz SerDes lanes serving:
  Two Serial RapidIO interfaces. Each supports up to 4 lanes and a total
    of up to 8 lanes
  Up to 8-lanes Common Public Radio Interface (CPRI) controller for glue-
    less antenna connection
  Two 10-Gbit Ethernet controllers (10GEC)
  Six 1G/2.5-Gbit Ethernet controllers for network communications
  PCI Express controller
  Debug (Aurora)
Two OCeaN DMAs
Various system peripherals
182 32-bit timers

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 14:31:24 -05:00
York Sun
9e75875849 powerpc/mpc85xx: Add T4240 SoC
Add support for Freescale T4240 SoC. Feature of T4240 are
(incomplete list):

12 dual-threaded e6500 cores built on Power Architecture® technology
  Arranged as clusters of four cores sharing a 2 MB L2 cache.
  Up to 1.8 GHz at 1.0 V with 64-bit ISA support (Power Architecture
    v2.06-compliant)
  Three levels of instruction: user, supervisor, and hypervisor
1.5 MB CoreNet Platform Cache (CPC)
Hierarchical interconnect fabric
  CoreNet fabric supporting coherent and non-coherent transactions with
    prioritization and bandwidth allocation amongst CoreNet end-points
  1.6 Tbps coherent read bandwidth
  Queue Manager (QMan) fabric supporting packet-level queue management and
    quality of service scheduling
Three 64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
    support
  Memory prefetch engine (PMan)
Data Path Acceleration Architecture (DPAA) incorporating acceleration for
    the following functions:
  Packet parsing, classification, and distribution (Frame Manager 1.1)
  Queue management for scheduling, packet sequencing, and congestion
    management (Queue Manager 1.1)
  Hardware buffer management for buffer allocation and de-allocation
    (BMan 1.1)
  Cryptography acceleration (SEC 5.0) at up to 40 Gbps
  RegEx Pattern Matching Acceleration (PME 2.1) at up to 10 Gbps
  Decompression/Compression Acceleration (DCE 1.0) at up to 20 Gbps
  DPAA chip-to-chip interconnect via RapidIO Message Manager (RMAN 1.0)
32 SerDes lanes at up to 10.3125 GHz
Ethernet interfaces
  Up to four 10 Gbps Ethernet MACs
  Up to sixteen 1 Gbps Ethernet MACs
  Maximum configuration of 4 x 10 GE + 8 x 1 GE
High-speed peripheral interfaces
  Four PCI Express 2.0/3.0 controllers
  Two Serial RapidIO 2.0 controllers/ports running at up to 5 GHz with
    Type 11 messaging and Type 9 data streaming support
  Interlaken look-aside interface for serial TCAM connection
Additional peripheral interfaces
  Two serial ATA (SATA 2.0) controllers
  Two high-speed USB 2.0 controllers with integrated PHY
  Enhanced secure digital host controller (SD/MMC/eMMC)
  Enhanced serial peripheral interface (eSPI)
  Four I2C controllers
  Four 2-pin or two 4-pin UARTs
  Integrated Flash controller supporting NAND and NOR flash
Two eight-channel DMA engines
Support for hardware virtualization and partitioning enforcement
QorIQ Platform's Trust Architecture 1.1

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 14:31:23 -05:00
York Sun
d1001e3f0c powerpc/corenet2: Add SerDes for corenet2
Create new files to handle 2nd generation Chassis as the registers are
organized differently.

 - Add SerDes protocol parsing and detection
 - Add support of 4 SerDes
 - Add CPRI protocol in fsl_serdes.h
	The Common Public Radio Interface (CPRI) is publicly available
	specification that standardizes the protocol interface between the
	radio equipment control (REC) and the radio equipment (RE) in wireless
	basestations. This allows interoperability of equipment from different
	vendors,and preserves the software investment made by wireless service
	providers.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 14:31:19 -05:00
Timur Tabi
4905443f1c powerpc/85xx: Add P5040 processor support
Add support for the Freescale P5040 SOC, which is similar to the P5020.
Features of the P5040 are:

Four P5040 single-threaded e5500 cores built
    Up to 2.4 GHz with 64-bit ISA support
    Three levels of instruction: user, supervisor, hypervisor
CoreNet platform cache (CPC)
    2.0 MB configures as dual 1 MB blocks hierarchical interconnect fabric
Two 64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
        support Up to 1600MT/s
    Memory pre-fetch engine
DPAA incorporating acceleration for the following functions
    Packet parsing, classification, and distribution (FMAN)
    Queue management for scheduling, packet sequencing and
    congestion management (QMAN)
    Hardware buffer management for buffer allocation and
    de-allocation (BMAN)
    Cryptography acceleration (SEC 5.2) at up to 40 Gbps SerDes
    20 lanes at up to 5 Gbps
    Supports SGMII, XAUI, PCIe rev1.1/2.0, SATA Ethernet interfaces
    Two 10 Gbps Ethernet MACs
    Ten 1 Gbps Ethernet MACs
High-speed peripheral interfaces
    Two PCI Express 2.0/3.0 controllers
Additional peripheral interfaces
    Two serial ATA (SATA 2.0) controllers
    Two high-speed USB 2.0 controllers with integrated PHY
    Enhanced secure digital host controller (SD/MMC/eMMC)
    Enhanced serial peripheral interface (eSPI)
    Two I2C controllers
    Four UARTs
    Integrated flash controller supporting NAND and NOR flash
DMA
    Dual four channel
Support for hardware virtualization and partitioning enforcement
    Extra privileged level for hypervisor support
QorIQ Trust Architecture 1.1
    Secure boot, secure debug, tamper detection, volatile key storage

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 14:31:13 -05:00
Liu Gang
d59c557049 powerpc/srio: Workaround for srio erratrm a004034
Erratum: A-004034
Affects: SRIO

Description: During port initialization, the SRIO port performs
lane synchronization (detecting valid symbols on a lane) and
lane alignment (coordinating multiple lanes to receive valid data
across lanes). Internal errors in lane synchronization and lane
alignment may cause failure to achieve link initialization at
the configured port width.

An SRIO port configured as a 4x port may see one of these scenarios:

1.	One or more lanes fails to achieve lane synchronization.
	Depending on which lanes fail, this may result in downtraining
	from 4x to 1x on lane 0, 4x to 1x on lane R (redundant lane).

2.	The link may fail to achieve lane alignment as a 4x, even
	though all 4 lanes achieve lane synchronization, and downtrain
	to a 1x. An SRIO port configured as a 1x port may fail to complete
	port initialization (PnESCSR[PU] never deasserts) because of
	scenario 1.

Impact: SRIO port may downtrain to 1x, or may fail to complete
link initialization. Once a port completes link initialization
successfully, it will operate normally.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 14:31:12 -05:00
Zang Roy-R61911
4e0be34a85 P4080/esdhc: make the P4080 ESDHC13 errata workaround conditional
P4080 Rev3.0 fixes ESDHC13 errata, so update the code to make the
workaround conditional.
In formal release document, the errata number should be ESDHC13 instead
of ESDHC136.

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 03:04:28 -05:00
Prabhakar Kushwaha
e4879afba3 powerpc/mpc85xx:Enable debugger support to missed e500v2 SoC
Freescale's e500v1 and e500v2 cores (used in mpc85xx chips) have some
restrictions on external debugging (JTAG). Need to define define
CONFIG_SYS_PPC_E500_DEBUG_TLB to enable a temporary TLB entry to be
used during boot to work around the limitations.

Enable missed e500v2 SoC i.e. MPC8536, MPC8544, MPC8548 and MPC8572 for
debug support.

Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Cc: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 12:16:54 -05:00
Scott Wood
33eee330cc powerpc/fsl-corenet: work around erratum A004510
Erratum A004510 says that under certain load conditions, modified
cache lines can be discarded, causing data corruption.

To work around this, several CCSR and DCSR register updates need to be
made in a careful manner, so that there is no other transaction in
corenet when the update is made.

The update is made from a locked cacheline, with a delay before to flush
any previous activity, and a delay after to flush the CCSR/DCSR update.
We can't use a readback because that would be another corenet
transaction, which is not allowed.

We lock the subsequent cacheline to prevent it from being fetched while
we're executing the previous cacheline.  It is filled with nops so that a
branch doesn't cause us to fetch another cacheline.

Ordinarily we are running in a cache-inhibited mapping at this point, so
we temporarily change that.  We make it guarded so that we should never
see a speculative load, and we never do an explicit load.  Thus, only the
I-cache should ever fill from this mapping, and we flush/unlock it
afterward.  Thus we should avoid problems from any potential cache
aliasing between inhibited and non-inhibited mappings.

NOTE that if PAMU is used with this patch, it will need to use a
dedicated LAW as described in the erratum.  This is the responsibility
of the OS that sets up PAMU.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 12:16:54 -05:00
Scott Wood
3e978f5dc8 powerpc/fsl-corenet: remove dead variant symbols
These are not supported as individual build targets, but instead
are supported by another target.

The dead p4040 defines in particular had bitrotted significantly.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 12:16:54 -05:00
Timur Tabi
055ce08004 powerpc/85xx: remove support for the Freescale P3060
The P3060 was cancelled before it went into production, so there's no point
in supporting it.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 12:16:53 -05:00
York Sun
be7bebeac2 powerpc/mpc8xxx: Remove P1015 and P1016 from CPU list
P1015 is the same as P1011 and P1016 is the same as P1012 from software
point of view. They have different packages but share SVRs.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 10:24:16 -05:00
York Sun
57125f222e powerpc/mpc85xx: Make NMG_CPU_A011 workaround conditional
This erratum applies to the following SoCs:
P4080 rev 1.0, 2.0, fixed in rev 3.0
P2041 rev 1.0, 1.1, fixed in rev 2.0
P3041 rev 1.0, 1.1, fixed in rev 2.0.

Workaround for erratum NMG_CPU_A011 is enabled by default. This workaround
may degrade performance. P4080 erratum CPU22 shares the same workaround.
So it is always enabled for P4080. For other SoCs, it can be disabled by
hwconfig with syntax:

fsl_cpu_a011:disable

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 10:24:13 -05:00
York Sun
5e23ab0a31 powerpc/mpc85xx: Workaround for erratum CPU_A011
Erratum NMG_CPU_A011 applies to P4080 rev 1.0, 2.0, fixed in rev 3.0.
It also applies to P3041 rev 1.0, 1.1, P2041 rev 1.0, 1.1. It shares the
same workaround as erratum CPU22. Rearrange registers usage in assembly
code to avoid accidental overwriting.

Signed-off-by: York Sun <yorksun@freescale.com>
2012-07-06 17:30:33 -05:00
Prabhakar Kushwaha
ad75d44239 powerpc/mpc85xx:Add debugger support for e500v2 SoC
Freescale's e500v1 and e500v2 cores (used in mpc85xx chips) have some
restrictions on external debugging (JTAG).

So define CONFIG_SYS_PPC_E500_DEBUG_TLB to enable a temporary TLB entry to be
used during boot to work around the limitations.

Please refer doc/README.mpc85xx for more information

Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
2012-07-06 17:30:31 -05:00
Prabhakar Kushwaha
19a8dbdc45 powerpc/mpc85xx:Add BSC9131/BSC9130/BSC9231 Processor Support
- BSC9131 is integrated device that targets Femto base station market.
   It combines Power Architecture e500v2 and DSP StarCore SC3850 core
   technologies with MAPLE-B2F baseband acceleration processing elements.
 - BSC9130 is exactly same as BSC9131 except that the max e500v2
   core and DSP core frequencies are 800M(these are 1G in case of 9131).
 - BSC9231 is similar to BSC9131 except no MAPLE

The BSC9131 SoC includes the following function and features:
    . Power Architecture subsystem including a e500 processor with 256-Kbyte shared
      L2 cache
    . StarCore SC3850 DSP subsystem with a 512-Kbyte private L2 cache
    . The Multi Accelerator Platform Engine for Femto BaseStation Baseband
      Processing (MAPLE-B2F)
    . A multi-standard baseband algorithm accelerator for Channel Decoding/Encoding,
     Fourier Transforms, UMTS chip rate processing, LTE UP/DL Channel processing,
     and CRC algorithms
    . Consists of accelerators for Convolution, Filtering, Turbo Encoding,
     Turbo Decoding, Viterbi decoding, Chiprate processing, and Matrix Inversion
     operations
    . DDR3/3L memory interface with 32-bit data width without ECC and 16-bit with
     ECC, up to 400-MHz clock/800 MHz data rate
    . Dedicated security engine featuring trusted boot
    . DMA controller
    . OCNDMA with four bidirectional channels
    . Interfaces
    . Two triple-speed Gigabit Ethernet controllers featuring network acceleration
      including IEEE 1588. v2 hardware support and virtualization (eTSEC)
    . eTSEC 1 supports RGMII/RMII
    . eTSEC 2 supports RGMII
    . High-speed USB 2.0 host and device controller with ULPI interface
    . Enhanced secure digital (SD/MMC) host controller (eSDHC)
    . Antenna interface controller (AIC), supporting three industry standard
      JESD207/three custom ADI RF interfaces (two dual port and one single port)
      and three MAXIM's MaxPHY serial interfaces
    . ADI lanes support both full duplex FDD support and half duplex TDD support
    . Universal Subscriber Identity Module (USIM) interface that facilitates
      communication to SIM cards or Eurochip pre-paid phone cards
    . TDM with one TDM port
    . Two DUART, four eSPI, and two I2C controllers
    . Integrated Flash memory controller (IFC)
    . TDM with 256 channels
    . GPIO
    . Sixteen 32-bit timers

The DSP portion of the SoC consists of DSP core (SC3850) and various
accelerators pertaining to DSP operations.

This patch takes care of code pertaining to power side functionality only.

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Akhil Goyal <Akhil.Goyal@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Rajan Srivastava <rajan.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
2012-07-06 17:03:25 -05:00
Liu Gang
7d67ed58a2 powerpc/srio: Rewrite the struct ccsr_rio
Rewrite this struct for the support of two ports and two message
units registers.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
2012-04-24 23:58:32 -05:00
Timur Tabi
3e0529f742 powerpc/85xx: CONFIG_FSL_SATA_V2 should be defined in config_mpc85xx.h
Macro CONFIG_FSL_SATA_V2 is defined if the SOC has a V2 Freescale SATA
controller, so it should be defined in config_mpc85xx.h instead of the various
board header files.  So now CONFIG_FSL_SATA_V2 is always defined on the P1013,
P1022, P2041, P3041, P5010, and P5020.  It was already defined for the
P1010 and P1014.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-29 08:48:06 -06:00
York Sun
4108508a96 powerpc/85xx: Add workaround for erratum A-003474
Erratum A-003474: Internal DDR calibration circuit is not supported

Impact:
Experience shows no significant benefit to device operation with
auto-calibration enabled versus it disabled. To ensure consistent timing
results, Freescale recommends this feature be disabled in future customer
products. There should be no impact to parts that are already operating
in the field.

Workaround:
Prior to setting DDR_SDRAM_CFG[MEM_EN]=1, do the following:
1. Write a value of 0x0000_0015 to the register at offset
	CCSRBAR + DDR OFFSET + 0xf30
2. Write a value of 0x2400_0000 to the register at offset
	CCSRBAR + DDR OFFSET + 0xf54

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-29 08:48:06 -06:00
Kumar Gala
43f082bb7f powerpc/85xx: Add workaround for erratum CPU-A003999
Erratum A-003999: Running Floating Point instructions requires special
initialization.

Impact:
Floating point arithmetic operations may result in an incorrect value.

Workaround:
Perform a read modify write to set bit 7 to a 1 in SPR 977 before
executing any floating point arithmetic operation. This bit can be set
when setting MSR[FP], and can be cleared when clearing MSR[FP].
Alternatively, the bit can be set once at boot time, and never cleared.
There will be no performance degradation due to setting this bit.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-29 08:48:05 -06:00
chenhui zhao
aada81de70 powerpc/mpc8548: Add workaround for erratum NMG_eTSEC129
Erratum NMG_eTSEC129 (eTSEC86 in MPC8548 document) applies to some early
verion silicons. This workaround detects if the eTSEC Rx logic is properly
initialized, and reinitialize the eTSEC Rx logic.

Signed-off-by: Gong Chen <g.chen@freescale.com>
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-08 08:30:32 -06:00
Shengzhou Liu
6d7b061af1 powerpc/p3060: Add SoC related support for P3060 platform
Add P3060 SoC specific information:cores setup, LIODN setup, etc

The P3060 SoC combines six e500mc Power Architecture processor cores with
high-performance datapath acceleration architecture(DPAA), CoreNet fabric
infrastructure, as well as network and peripheral interfaces.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-03 09:36:28 -05:00
Kumar Gala
2b3a1cdd9e powerpc/mpc8548: Add workaround for erratum NMG_LBC103
The erratum NMG_LBC103 is LBIU3 in MPC8548 errata document.
Any local bus transaction may fail during LBIU resynchronization
process when the clock divider [CLKDIV] is changing. Ensure there
is no transaction on the local bus for at least 100 microseconds
after changing clock divider LCRR[CLKDIV].

Refer to the erratum LBIU3 of mpc8548.

Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-03 08:52:15 -05:00
Kumar Gala
5ace2992b5 powerpc/mpc8548: Add workaround for erratum NMG_DDR120
Erratum NMG_DDR120 (DDR19 in MPC8548 errata document) applies to some
early version silicons. The default settings of the DDR IO receiver
biasing may not work at cold temperature. When a failure occurs,
a DDR input latches an incorrect value. The workaround will set the
receiver to an acceptable bias point.

Signed-off-by: Gong Chen
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-03 08:52:14 -05:00
Poonam Aggrwal
bc6bbd6be8 fsl_ifc: Add the workaround for erratum IFC A-003399(enabled on P1010)
Issue: Address masking doesn't work properly.
When sum of the base address, defined by BA, and memory bank size,
defined by AM, exceeds 4GB (0xffff_ffff) then AMASKn[AM] doesn't mask
CSPRn[BA] bits.

Impact:
This will impact booting when we are reprogramming CSPR0(BA) and
AMASK0(AMASK) while executing from NOR Flash.

Workaround:
Re-programming of CSPR(BA) and AMASK is done while not executing from NOR
Flash. The code which programs the BA and AMASK is executed from L2-SRAM.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:04 -05:00
Poonam Aggrwal
fb855f43a1 powerpc/P1010: Add workaround for erratum P1010-A003549 (related to IFC)
Issue:
Peripheral connected to IFC_CS3 may hamper booting from IFC.

Impact:
Boot from IFC may not be successful if IFC_CS3 is used.

Workaround:
If IFC_CS3 is used, gate IFC_CS3 while booting from NAND or NOR.
Also Software should select IFC_CS3 using PMUXCR[26:27] = 0x01.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:04 -05:00
Poonam Aggrwal
42aee64bd9 fsl_ifc: Add the workaround for erratum IFC-A002769 (enable on P1010)
Issue:
The NOR-FCM does not support access to unaligned addresses for 16 bit port size

Impact:
When 16 bit port size is used, accesses not aligned to 16 bit address boundary
will result in incorrect data

Workaround:
The workaround is to switch to GPCM mode for NOR Flash access.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:04 -05:00
Timur Tabi
e46fedfeb2 powerpc/85xx: introduce and document CONFIG_SYS_CCSRBAR macros
Introduce the CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW
macros, which contain the high and low portions of CONFIG_SYS_CCSRBAR_PHYS.
This is necessary for the assembly-language code that relocates CCSR, since
the assembler does not understand 64-bit constants.

CONFIG_SYS_CCSRBAR_PHYS is automatically defined from the
CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW macros, so it
should not be defined in a board header file.  Similarly,
CONFIG_SYS_CCSRBAR_DEFAULT is defined for each SOC in config_mpc85xx.h, so
it should also not be defined in the board header file.

CONFIG_SYS_CCSR_DO_NOT_RELOCATE is a "short-cut" macro that guarantees that
CONFIG_SYS_CCSRBAR_PHYS is set to the same value as CONFIG_SYS_CCSRBAR_DEFAULT,
and so CCSR will not be relocated.

Since CONFIG_SYS_CCSRBAR_DEFAULT is locked to a fixed value, multi-stage U-Boot
builds (e.g. NAND) are required to relocate CCSR only during the last stage
(i.e. the "real" U-Boot).  All other stages should define
CONFIG_SYS_CCSR_DO_NOT_RELOCATE to ensure that CCSR is not relocated.

README is updated with descriptions of all the CONFIG_SYS_CCSRBAR_xxx macros.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:04 -05:00
Kumar Gala
b6c3722dfa powerpc/85xx: Enable internal USB UTMI PHY on p204x/p3041/p50x0
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:03 -05:00
Ramneek Mehresh
1b719e6654 powerpc/85xx: Add ULPI and UTMI USB Phy support for P1010/P1014
Add UTMI and ULPI PHY support for USB controller on qoriq series of
processors with internal UTMI PHY implemented, for example P1010/P1014
 - Use both getenv() and hwconfig to get USB phy type till getenv()
   is depricated
 - Introduce CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY to specify if soc
   has internal UTMI phy

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Acked-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:03 -05:00
Kumar Gala
1f97987a51 powerpc/85xx: Add P2041 processor support
The P2041 is similar to P2040, however has a 10G port and backside L2

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-11 13:24:19 -05:00
Kumar Gala
8f29084a4f powerpc/fsl_pci: Fix device tree fixups for newer platforms
We assumed that only a small set of compatiable strings would be needed
to find the PCIe device tree nodes to be fixed up.  However on newer
platforms the simple rules no longer work.  We need to allow specifying
the PCIe compatiable string for each individual SoC.

We introduce CONFIG_SYS_FSL_PCIE_COMPAT for this purpose and set it if
the default isn't sufficient.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-05-20 00:48:41 -05:00
Kumar Gala
66412c6371 powerpc/85xx: Change timebase divisor to be defined per processor
Introduce new CONFIG_SYS_FSL_TBCLK_DIV on 85xx platforms because
different SoCs have different divisor amounts.  All the PQ3 parts are
/8, the P4080/P4080 is /16, and P2040/P3041/P5020 are /32.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-28 22:09:24 -05:00
Timur Tabi
d90fdba6ca powerpc/85xx: Implement work-around for P4080 erratum SERDES-A001
Bank powerdown through RCW[SRDS_LPD_Bn] for XAUI on FM2 and SGMII on FM1
are swapped.

Erratum SERDES-A001 says that if bank two is kept disabled and after bank
three is enabled, then the PLL for bank three won't lock properly.  The
work-around is to enable and then disable bank two after bank three is
enabled.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-28 22:09:23 -05:00
Timur Tabi
da30b9fd97 powerpc/85xx: Implement work-around for P4080 erratum SERDES-A005
SerDes PLL bandwidth default setting is incorrect when no lanes are
configured as PCI Express.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-28 22:09:23 -05:00
Lei Xu
300097669c powerpc/85xx: Enable ESDHC111 erratum on P2040/P3041/P5010/P5020 SoCs
The workaround for ESDHC111 should also be applied on
P2040/P3041/P5010/P5020 SoCs.

Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-27 22:29:04 -05:00
Roy Zang
86221f09fb powerpc/85xx: Enable Internal USB PHY for p2040, p3041, p5010 and p5020
The P2040, P3041, P5010, and P5020 all have internal USB PHYs that we
need to enable for them to function.

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-27 22:29:04 -05:00
Emil Medve
df8af0b4a6 p4080/serdes: Implement the XAUI workaround for SERDES9 erratum
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-27 22:29:04 -05:00
Priyanka Jain
32c8cfb23c fsl_esdhc: Deal with watermark level register related changes
P1010 and P1014 has v2.3 version of FSL eSDHC controller in which watermark
level register description has been changed:

9-15 bits represent WR_WML[0:6], Max value = 128 represented by 0x00
25-31 bits represent RD_WML[0:6], Max value = 128 represented by 0x00

Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <Poonam.Aggrwal@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-10 11:17:55 -05:00
Haiying Wang
a52d2f816d powerpc/85xx: Add P1021 specific QE and UEC support
P1021 has some QE pins which need to be set in pmuxcr register before
using QE functions. In this patch, pin QE0 and QE3 are set for UCC1 and
UCC5 in Eth mode.  QE9 and QE12 are set for MII management. QE12 needs to
be released after MII access because QE12 pin is muxed with LBCTL signal.

Also added relevant QE support defines unique to P1021.

The P1021 QE is shared on P1012, P1016, and P1025.

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-05 10:18:39 -05:00
Kumar Gala
b5c8753fa1 powerpc/85xx: Fixup determining PME, FMan freq
On CoreNet based SoCs (P2040, P3041, P4080, P5020) we have some
additional rules to determining the various frequencies that PME & FMan
IP blocks run at.

We need to take into account:
* Reduced number of Core Complex PLL clusters
* HWA_ASYNC_DIV (allows for /2 or /4 options)

On P2040/P3041/P5020 we only have 2 Core Complex PLLs and in such SoCs
the PME & FMan blocks utilize the second Core Complex PLL.  On SoCs
like p4080 with 4 Core Complex PLLs we utilize the third Core Complex
PLL for PME & FMan blocks.

On P2040/P3041/P5020 we have the added feature that we can divide the
PLL down further by either /2 or /4 based on HWA_ASYNC_DIV.  On P4080
this options doesn't exist, however HWA_ASYNC_DIV field in RCW should be
set to 0 and this gets a backward compatiable /2 behavior.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:43 -05:00
Kumar Gala
c657d898bc powerpc/85xx: Specify CONFIG_SYS_FM_MURAM_SIZE
CONFIG_SYS_FM_MURAM_SIZE varies from SoC to SoC to specify it in
config_mpc85xx.h for those parts with a Frame Manager.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:42 -05:00
Poonam Aggrwal
1fbf3483b7 powerpc/85xx: Adds some P1010/P1014 SoC configuration defines
Add defines for FSL_SATA_V2, # of DDR controllers, reset value of CCSRBAR
and SDHC erratum.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:42 -05:00
Kumar Gala
093cffbe9a powerpc/85xx: Support for Freescale P1024/P1025 processor
Add Support for Freescale P1024/P1025 (dual core) and
P1015/P1016 (single core) processors.

P1024 is a variant of P1020 processor with a core frequency from
400Mhz to 667Mhz and comes in a 561-pin wirebond power-BGA

P1025 is a variant of P1021 processor with a core frequency from
400Mhz to 667Mhz and comes in a 561-pin wirebond power-BGA

P1015 is a variant of P1024 processor with single core and P1016 is a
variant of P1025 processor with single core.

Added comments in config_mpc85xx.h to denote single core versions of
processors.

Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:42 -05:00
Roy Zang
67a719da2e powerpc/85xx: Add support for Freescale P1023/P1017 Processors
Add P1023 (dual core) & P1017 (single core) specific information:
* SERDES Table
* Added P1023/P1017 to cpu_type_list and SVR list
  (fixed issue with P1013 not being sorted correctly).
* Added P1023/P1027 to config_mpc85xx.h
* Added new LAW type introduced on P1023/P1017
* Updated a few immap register/defines unique to P1023/P1017

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:41 -05:00
Kumar Gala
fdb4dad31e powerpc/85xx: Cleanup some QE related defines
Move some processor specific QE defines into config_mpc85xx.h and use
QE_MURAM_SIZE to cleanup some ifdef mess in the QE immap struct.

Also fixed up some comment style issues in immap_qe.h

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:41 -05:00
Kumar Gala
fbee0f7f09 powerpc/85xx: Add some defines for P2040, P3041, P5010, P5020
Specify the number of DDR controllers, number of frame managers, number
of 1g and 10g ports.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:40 -05:00
Prabhakar Kushwaha
b03a466d6c powerpc/85xx: Handle PCIe initialization requires for P1021 class SoCs
The P1011, P1012, P1015, P1016, P1020, P1021, P1024, & P1025 SoCs require
that we initialize the SERDES registers if the lanes are configured for
PCIe.  Additionally these devices PCIe controller do not support ASPM
and we have to explicitly disable it.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-03-29 07:41:37 -05:00
Jiang Yutang
2d7534a344 powerpc/85xx: Enable various errata on P1022/P1013 SoCs
Enable workaround for errata ELBC A001, ESDHC 111 & SATA A001 on
P1022/P1013 SoCs.

Also updated P1022DS config to properly enable CONFIG_FSL_SATA_V2.

Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-03-28 09:04:26 -05:00
York Sun
91671913f7 powerpc/mpc85xx: implement workaround for errata DDR111 and DDR134
Workaround for the following errata:
DDR111 - MCKE signal may not function correctly at assertion of HRESET
DDR134 - The automatic CAS-to-Preamble feature of the DDR controller can
         calibrate to incorrect values

These two workarounds must be implemented together because they touch
common registers.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-02-03 02:46:13 -06:00
York Sun
eb0aff77c8 powerpc/85xx: Rename MPC8572 DDR erratum to DDR115
Use unique erratum number instead of platform number.
Enable command that reports errata on MPC8572DS.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-02-03 02:46:13 -06:00
Kumar Gala
5103a03a0b fsl_esdhc: Add the workaround for erratum ESDHC-A001 (enable on P2020)
Data timeout counter (SYSCTL[DTOCV]) is not reliable for values of 4, 8,
and 12. Program one more than the desired value: 4 -> 5, 8 -> 9, 12 -> 13.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-02-03 02:46:12 -06:00
Kumar Gala
6e7f0bc0ce powerpc/85xx: Enable ESDHC111 Erratum on P2010/P2020 SoCs
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-02-03 02:46:12 -06:00
Wolfgang Denk
d1a24f0618 Minor Coding Style Cleanup.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-02-02 22:36:10 +01:00
York Sun
fa8d23c0ee mpc85xx: Implement workaround for erratum DDR-A003
Erratum DDR-A003 requires workaround to correctly set RCW10 for registered DIMM.
Also adding polling after enabling DDR controller to ensure completion.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19 22:58:24 -06:00
Kumar Gala
243be8e296 powerpc/8xxx: Introduce 85xx, 86xx, QorIQ config headers
Add new headers that capture common defines for a given SoC/processor
rather than duplicating that information in board config.h and random
other places.

Eventually this should be handled by Kconfig & defconfigs

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
2011-01-19 22:58:23 -06:00