Enable UFS controller driver and matching UFS and SCSI commands. The
former is used to initialize the device, the later is used to perform
low level access to the SCSI interface of the UFS device.
Enable R8A779F0 S4 Spider specific dependencies, the PCA953x driver
and GPIO clock gate driver. This setup is used to toggle 38.4 MHz
clock for the UFS controller.
Enable support for 48bit LBA in block layer to address disks larger
than 512*2^32 ~= 144 PiB. Enable use of 64bit LBA variables in the
rest of U-Boot, instead of the default 32bit ones.
Increase FAT cluster size to 128k as that is what is used by the
filesystem that is populated on the UFS device.
Use 'ufs init && scsi scan' to start the UFS device from U-Boot prompt.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
At this point, system shutdown is not supported by the DM firmware
that TF-A calls. As we can't de-select only this feature[1], declare
complete PSCI reset support as non-functional so that we don't signal
incomplete support to the OS via EFI runtime services. This makes
power-off under Linux work again when booting via EFI.
[1] https://uefi.org/specs/UEFI/2.9_A/08_Services_Runtime_Services.html?highlight=efiresetshutdown#resetsystem
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Switch to using bootstd. Note with this change, we will stop using
distro_bootcmd and instead depend entirely on bootflow method of
starting the system up.
Suggested-by: Tom Rini <trini@konsulko.com>
Suggested-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Align the sandbox64 defconfig with sandbox defconfig. Enable missing
legacy image format support. This fixes ut_bootstd_bootflow_cmd_menu
test.
Suggested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
SPL_SYS_MALLOC_CLEAR_ON_INIT would enable SYS_MALLOC_CLEAR_ON_INIT by
default, but that's not need on JH7110, so disable that.
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Although PCIE driver already exists, board defconfig isn't configured to
enable PCIE enum on boot, thus USB storage device and NVME drive are not
supported by default. So modify defconfig to enable PCIE auto enum, then
start USB subsystem and scan nvme drive on boot.
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Tested-by: Milan P. Stanić <mps@arvanta.net>
This platform is behind on migrations (it is the sole user of the oldest
legacy version of the USB gadget stack and is long overdue for
migration) and with Pali no longer being a maintainer, we remove this
platform.
Signed-off-by: Tom Rini <trini@konsulko.com>
Select the i.MX8MM thermal driver as it is useful for displaying
the CPU temperature and its grading:
CPU: Commercial temperature grade (0C to 95C) at 38C
It also prevents booting when the temperature is above the alert
point.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Use default SAVED_DRAM_TIMING_BASE as that is what upstream TFA expects.
Without this change, the board will fail to suspend/resume e.g. in Linux.
Signed-off-by: Marek Vasut <marex@denx.de>
Use default SAVED_DRAM_TIMING_BASE as that is what upstream TFA expects.
Without this change, the board will fail to suspend/resume e.g. in Linux.
Signed-off-by: Marek Vasut <marex@denx.de>
Use default SAVED_DRAM_TIMING_BASE as that is what upstream TFA expects.
Without this change, the board will fail to suspend/resume e.g. in Linux.
Signed-off-by: Marek Vasut <marex@denx.de>
U-Boot splits DRAM bank spanning addresses below and above the 32bit
boundary into two DRAM banks. Since this platform may come with 4GiB
of DRAM, increase the DRAM bank count to 2.
Signed-off-by: Marek Vasut <marex@denx.de>
This board certainly does use default 'run distro_bootcmd' boot command,
make sure this is set in 'bootcmd' variable.
Fixes: 970bf8603b ("Convert CONFIG_USE_BOOTCOMMAND et al to Kconfig")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Disable this option to reclaim some space, since bootstd requires less
functionality to operate (e.g. hush parser).
Signed-off-by: Simon Glass <sjg@chromium.org>
Drop use of the distro scripts and use standard boot instead.
We don't need to specify the mmc devices individually, since they are
used in order from 0 to 2, and standard boot uses that order anyway.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a new event which handles this function. Convert existing use of
the function to use the new event instead.
Make sure that EVENT is enabled by affected boards, by selecting it from
the LAST_STAGE_INIT option. For x86, enable it by default since all boards
need it.
For controlcenterdc, inline the get_tpm() function and make sure the event
is not built in SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmTu+QMcHGV1Z2VuLmhy
aXN0ZXZAY29sbGFib3JhLmNvbQAKCRAesx4CDqwvyFqVB/9z5lV4zhqWYiQ+wNZL
Gxs3//DSS5iVHU+xaPRrYQT99Yn2/kfM2LeQ4REBOaOTP7IX2ewmOEro4OUViFuC
kt/WnHD0XzN+2o8akIdVC5YudgVcuX751SQtp5dqcbN6FylSH010+YIZTvaJoNQn
+Wny1ZZhpuNJJEPvLxE/eiJ3jFwvEAjC+jH328uQIeSLknPh93hGJOFc/02F0O2o
s96J1/VZ4qvvQKYw0sgNtGb/0Og7V0RLW27+RfwhH4XJvAIv/A6MioTyRaCS2h7H
tzj/hFXbzGtu+AqrEtMgNjzC7vAx+0266P/Zx/DOWKoWLDIYkWSLpYKLut0E6CUe
+fcB
=L/iw
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2023.10-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2023.10 cycle:
This feature set includes a new board sama5d29 Curiosity, and various
fixes and alignments for sam9x60 and sam9x60 curiosity board.
Add the path to the public key EFI Signature List(ESL) file for the
sandbox variants which enable capsule authentication. This ESL file
gets embedded into the platform's device-tree as part of the build.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Enable the EFI capsule update code on all sandbox variants. This was
already enabled on the sandbox, sandbox64 and sandbox_flattree
variants. The rest of the variants also have the EFI capsule update
module enabled now. With this commit, the mkeficapsule tool also gets
enabled on all variants.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since commit 61040097a9 ("reset: at91: Add reset driver for basic
assert/deassert operations") the compatible "microchip,sam9x60-rstc" for
the sam9x60 reset controller in sam9x60.dtsi is not handled by
CONFIG_SYSRESET_AT91 anymore, but by CONFIG_RESET_AT91 now. This
resulted in the following error message, when trying to reset from
U-Boot shell:
U-Boot> reset
resetting ...
System reset not supported on this platform
### ERROR ### Please RESET the board ###
Fixed by enabling the new driver in the relevant defconfigs. Tested on
sam9x60-curiosity board. Defconfigs for sam9x60ek adapted in the same
way, but without testing. These should be all sam9x60 boards affected
in U-Boot here.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
The board has two SD card slots and we have two defconfigs for booting
from either the first (micro SD) named 'sam9x60_curiosity_mmc_defconfig'
or the second (full size SD) named 'sam9x60_curiosity_mmc1_defconfig'.
For comparable Microchip boards (sama5d27-som1-ek, sama5d29-curiosity,
sama7g5ek) with two card slots the defconfigs only differ in BOOTARGS,
BOOTCOMMAND, and ENV_FAT_DEVICE_AND_PART and the same should be the case
for sam9x60_curiosity.
Here the 'mmc1' config has more options enabled to support the raw NAND
flash populated on the board, so the 'mmc' config (for mmc0) was adapted
by enabling additional options, instead of removing options from mmc1.
The 'mem=128M' argument can be dropped from kernel command line, because
it is redundant to memory node in dts in both Linux and U-Boot:
memory@20000000 {
reg = <0x20000000 0x8000000>;
};
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Similar to MT7981 and MT7986 also MT7988 can have a high number of
reserved-memory regions used by the various hardware offloading
subsystems.
Raise CONFIG_LMB_MAX_REGIONS to 64 to avoid errors when trying to boot
Linux with more then 6 reserved regions:
ERROR: reserving fdt memory region failed (addr=4f700000 size=240000 flags=4)
ERROR: reserving fdt memory region failed (addr=15194000 size=1000 flags=4)
ERROR: reserving fdt memory region failed (addr=15294000 size=1000 flags=4)
ERROR: reserving fdt memory region failed (addr=15394000 size=1000 flags=4)
ERROR: Failed to allocate 0xb161 bytes below 0x80000000.
device tree - allocation error
Fixes: bc4adc97cf ("board: mediatek: add MT7988 reference boards")
Reported-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This should have already been enabled but was missed when converting the
base platform defconfig, fix this here.
Fixes: 3c5aa6cacc ("configs: Enable CONFIG_BLK in am57xx_evm and am57xx_hs_evm")
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The ChromiumOS bootmeth has no tests at present. Before adding more
features. add a basic test.
This creates a disk which can be scanned by the bootmeth, so make sure
things work. It is quite rudimentary, since the kernel is faked, the root
disk is missing and there is no cmdline stored.
Enable the bootmeth for snow so it can build the unit test.
Signed-off-by: Simon Glass <sjg@chromium.org>
Commit 02be57caf7 ("riscv: qemu: Enable usb keyboard as an input
device") adds PCI xHCI support to QEMU RISC-V virtual machines and
enables using a USB keyboard as one of the input devices. Similarly,
enable those for ARM virtual machines as well.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Align the sandbox64 defconfig with sandbox defconfig. Enable missing
PCI register multi-entry support. This fixes ut_dm_dm_test_pci_bus_to_phys
test .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Align the sandbox64 defconfig with sandbox defconfig. Enable missing
CCF and Sandbox CCF drivers. This fixes ut_dm_dm_test_clk_ccf test .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Align the sandbox64 defconfig with sandbox defconfig. Enable missing
12x22 font support. This fixes ut_dm_dm_test_video_text_12x22 test .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Align the sandbox64 defconfig with sandbox defconfig. Enable missing
16bpp and 24bpp video support. This fixes ut_dm_dm_test_video_bmp16
and ut_dm_dm_test_video_bmp24 tests .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Align the sandbox64 defconfig with sandbox defconfig. Enable missing
PINCTRL single driver. This fixes ut_dm_dm_test_pinctrl_single test .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Align the sandbox64 defconfig with sandbox defconfig. Enable missing
BUTTON ADC driver. This fixes ut_dm_dm_test_button_keys_adc test .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Align the sandbox64 defconfig with sandbox defconfig. Enable missing
MC34708 PMIC driver. This fixes ut_dm_dm_test_power_pmic_mc34708_get test .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Align the sandbox64 defconfig with sandbox defconfig. Increase the
console record size. This fixes ut_bootstd_bootflow_cmd_scan_e .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Align the sandbox64 defconfig with sandbox defconfig. Enable missing
SPI NOT bootdev. This fixes ut_bootstd_bootdev_test_cmd_hunt test .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rename defconfig to include SoC name, use similar pattern as other
RK356x boards: <soc>-<name>.dts -> <name>-<soc>_defconfig
Suggested-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This adds support for various new Tegra30 boards (ASUS, LG and HTC) and
has some other minor enhancements, such as enabling the poweroff command
on several Tegra210 and Tegra186 boards.
-----BEGIN PGP SIGNATURE-----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=Bzgn
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-2023.10-rc1' of https://source.denx.de/u-boot/custodians/u-boot-tegra
ARM: tegra: Changes for v2023.10-rc1
This adds support for various new Tegra30 boards (ASUS, LG and HTC) and
has some other minor enhancements, such as enabling the poweroff command
on several Tegra210 and Tegra186 boards.
Display the STMicroelectronics logo with features VIDEO_LOGO and
SPLASH_SCREEN on STMicroelectronics boards.
With CONFIG_SYS_VENDOR = "st", the logo st.bmp is selected, loaded at the
address indicated by splashimage and centered with "splashpos=m,m".
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The MAIN CPSW0 instance of CPSW Ethernet Switch on TI's J7200 SoC
supports SGMII mode. To enable support for utilizing the SGMII
daughtercard with TI's DP83869 PHY, enable the corresponding config.
Also, since the SGMII daughtercard is connected to the I2C GPIO
Expander 2 connector on the J7200 EVM, powering on the Ethernet PHY and
resetting it requires GPIO Hogging capability. Enable it as well.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
We need a platform on which we can test our semihosting code.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Add a new DM driver supporting FTPCI100 IP used in SoC designs.
This implementation is not based on the old non-DM ftpci100 code
dropped from U-Boot.
Enable the driver in sandbox_defconfig to test compilability.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
This is merely a dummy driver that makes sure the DWC3 XHCI driver
finds its reset and PHY controllers. We rely on iBoot to set up
the PHY for us.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
LubanCat2 is a rk3568 based SBC from EmbedFire.
Specification:
- Rockchip rk3568
- LPDDR4/4X 1/2/4/8 GB
- TF scard slot
- eMMC 8/32/64/128 GB
- Gigabit ethernet x 2
- HDMI out
- USB 2.0 Host x 1
- USB 2.0 Type-C OTG x 1
- USB 3.0 Host x 1
- Mini PCIE interface for WIFI/BT module
- M.2 key for 2280 NVME
- 40 pin header
The dts file is sync from linux mainline.
Signed-off-by: Andy Yan <andyshrk@163.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the rk3328 rng details to the u-boot.dtsi and
enable the RNG on the Rock64 to be able to provide
a random seed via UEFI.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
(Fix typo message)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Enable the rockchip efuse driver on the Rock64 to
provide a stable ethernet address on the device.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
On Starfive Visionfive 2, the u-boot environment settings are saved to
on-board SPI flash. Enable relative configs by default and set offset
and size according to upstream linux dts.
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add XHCI_PCI to enable usb3-host functions.
Also add usb command and keyboard config.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This build can be used to boot 32-bit standard-distro builds. Enable some
more options, so that all possible EFI UUIDs are decoded, we can search
memory for tables, support the full set of standard-boot features, have
full logging along with debug UART and can boot from CDROM media.
This mirrors a similar patch for qemu-x86_64
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[Drop the unknown option from defconfig]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Unfortunately the bochs driver does not currently work with distros.
It causes a hang between grub menu selection and the OS displaying
something.
Preliminary investigation shows that GRUB does not jump to the kernel
at all.
This reproduces reliably.
This reverts commit b8956425d5.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com> # qemu-x86_64
[Slightly modify the commit message about preliminary investigation]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
It is not a parse error to have a default value of "0" for a "hex" type
entry, instead of "0x0". However, "0" and "0x0" are not treated the
same even by the tools themselves. Correct this by changing the default
value from "0" to "0x0" for all hex type questions that had the
incorrect default. Fix one instance (in two configs) of a default of "0"
being used on a hex question to be "0x0". Remove the cases where a
defconfig had set a value of "0x0" to be used as the default had been
"0".
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
turn on EFI MM communication
On Corstone-1000 platform MM communication between u-boot
and the secure world (Optee) is done using the FF-A bus.
Changes made are generated using savedefconfig.
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Emulate Secure World's FF-A ABIs and allow testing U-Boot FF-A support
Features of the sandbox FF-A support:
- Introduce an FF-A emulator
- Introduce an FF-A device driver for FF-A comms with emulated Secure World
- Provides test methods allowing to read the status of the inspected ABIs
The sandbox FF-A emulator supports only 64-bit direct messaging.
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
This adds initial support for the Toradex Verdin AM62 Quad 1GB WB IT
V1.0A module and subsequent V1.1 launch configuration SKUs. They are
strapped to boot from their on-module eMMC. U-Boot supports booting
from the on-module eMMC only, DFU support is disabled for now due to
missing AM62x USB support.
The device trees were taken straight from Linux v6.5-rc1.
Boot sequence is:
SYSFW ---> R5 SPL (both in tiboot3.bin) ---> ATF (TF-A) ---> OP-TEE
---> A53 SPL (part of tispl.bin) ---> U-boot proper (u-boot.img)
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the previous updates to the device tree, Ten64
can use Standard Boot 'out of the box'.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The watchdog driver was previously enabled but not used
until U-Boot's fsl-ls1088a.dtsi was updated to describe them.
Some Linux distributions (e.g Debian 11) do not engage the
SP805 watchdogs, causing unexpected resets after boot.
To conserve the user experience, turn off the autostart,
and we will provide a mechanism to turn them on at boot
via env vars.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This restores NVMe functionality after PCI(e) NVMe support
was split out from the NVMe driver.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This patch adds general board files based on MT7988 SoCs.
MT7988 uses one mmc controller for booting from both SD and eMMC,
and the pins of mmc controller booting from SD are also shared with
one of spi controllers.
So two configs are need for these boot types:
1. mt7988_rfb_defconfig - SPI-NOR, SPI-NAND and eMMC
2. mt7988_sd_rfb_defconfig - SPI-NAND and SD
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The Unmatched board is typically booted from NVMe which requires PCI.
When dropping to a console PCI is not initialized yet. 'pci enum' has to be
called.
Change the configuration to call pci_init() in board_init_r().
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Radxa E25 is a network application carrier board for the Radxa CM3I SoM
with a RK3568 SoC. It features dual 2.5G ethernet, mini PCIe, M.2 B Key,
USB3, eMMC, SD, nano SIM card slot and a 26-pin GPIO header.
Features tested on a Radxa E25 v1.4:
- SD-card boot
- eMMC boot
- USB host
- PCIe/Ethernet adapters is detected
- SATA
Device tree is imported from linux next-20230728.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: FUKAUMI Naoki <naoki@radxa.com>
Enable USB 3.0 in all RK3328 boards.
=> usb start
starting USB...
Bus usb@ff5c0000: ehci_generic usb@ff5c0000: Failed to get clocks (ret=-19)
Port not available.
Bus usb@ff5d0000: USB OHCI 1.0
Bus usb@ff600000: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Bus usb@ff580000: 1 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
=> usb tree
USB device tree:
1 Hub (12 Mb/s, 0mA)
U-Boot Root Hub
1 Hub (5 Gb/s, 0mA)
| U-Boot XHCI Host Controller
|
+-2 Mass Storage (5 Gb/s, 224mA)
SanDisk Dual Drive 040130e3ee554b7078843f4eb331646
1 Hub (480 Mb/s, 0mA)
U-Boot Root Hub
Cc: Tianling Shen <cnsztl@gmail.com>
Cc: David Bauer <mail@david-bauer.net>
Cc: Loic Devulder <ldevulder@suse.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Banglang Huang <banglang.huang@foxmail.com>
Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Driver support for rk3328 is not supported so drop this
unused XHCI_DWC3.
Cc: Tianling Shen <cnsztl@gmail.com>
Cc: David Bauer <mail@david-bauer.net>
Cc: Loic Devulder <ldevulder@suse.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Banglang Huang <banglang.huang@foxmail.com>
Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There is an Errata with the built-in I2C controller where various I2C
hardware errors cause a complete lockup of the CPU (which eventually
results in an watchdog reset).
Put the I2C MPP pins into GPIO mode and use the i2c-gpio driver instead.
This uses a bit-banged implementation of an I2C controller and avoids
triggering the Errata.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
ROCK 5A is a Rockchip RK3588S based SBC (Single Board Computer) by Radxa.
There are tree variants depending on the DRAM size : 4G, 8G and 16G.
Specifications:
Rockchip Rk3588S SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
4/8/16GB memory LPDDR4x
Mali G610MC4 GPU
MIPI CSI 2 multiple lanes connector
4-lane MIPI DSI connector
Audio – 3.5mm earphone jack
eMMC module connector
uSD slot (up to 128GB)
2x USB 2.0, 2x USB 3.0
2x micro HDMI 2.1 ports, one up to 8Kp60, the other up to 4Kp60
Gigabit Ethernet RJ45 with optional PoE support
40-pin IO header including UART, SPI, I2C and 5V DC power in
USB PD over USB Type-C
Size: 85mm x 56mm (Raspberry Pi 4 form factor)
Kernel commits:
d1824cf95799 ("arm64: dts: rockchip: Add rock-5a board")
991f136c9f8d ("arm64: dts: rockchip: Update sdhci alias for rock-5a")
304c8a759953 ("arm64: dts: rockchip: Remove empty line from rock-5a")
cda0c2ea65a0 ("arm64: dts: rockchip: Fix RX delay for ethernet phy on rk3588s-rock5a")
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The commit fd6e425be2 ("rockchip: rk3588-rock-5b: Enable boot from SPI
NOR flash") enabled SPI flash support by adding a spi0 alias.
Correct this by adding spi0-spi5 aliases in rk3588s-u-boot.dtsi and
SF_DEFAULT_BUS=5 and SPL_DM_SEQ_ALIAS=y in defconfig. Also enabled
support for parsing and auto discovery of parameters, SFDP.
Fixes: fd6e425be2 ("rockchip: rk3588-rock-5b: Enable boot from SPI NOR flash")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The commit 64f79f88a7 ("rockchip: rk3568-rock-3a: Enable boot from SPI
NOR flash") enabled SPI flash support by overriding the spi0 alias.
Correct this by adding a new spi4 alias in rk356x-u-boot.dtsi and
SF_DEFAULT_BUS=4 and SPL_DM_SEQ_ALIAS=y in defconfig. Also enabled
support for parsing and auto discovery of parameters, SFDP.
Fixes: 64f79f88a7 ("rockchip: rk3568-rock-3a: Enable boot from SPI NOR flash")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
TPL max size is limited to 184 KB, SPL is loaded to 0x0 and TF-A is
loaded to 0x40000, this limit SPL max size to 256 KB. With BootRom only
reading first 2 KB per 4 KB page of SPI flash, 880 KB may be needed for
TPL+SPL in a worst-case scenario. (184 KB + 256 KB) x 2 = 880 KB
Use 0xE0000 (896 KB) as the payload offset in SPI flash, this allows
for a payload of 3168 KB before env offset start to overlap.
Also add CONFIG_ROCKCHIP_SPI_IMAGE=y to build a bootable SPI flash
image, u-boot-rockchip-spi.bin.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <foss+u-boot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
TPL max size is limited to 184 KB, SPL is loaded to 0x0 and TF-A is
loaded to 0x40000, this limit SPL max size to 256 KB. With BootRom only
reading first 2 KB per 4 KB page of SPI flash, 880 KB may be needed for
TPL+SPL in a worst-case scenario. (184 KB + 256 KB) x 2 = 880 KB
Use 0xE0000 (896 KB) as the payload offset in SPI flash, this allows
for a payload of 3168 KB before env offset start to overlap.
Also add CONFIG_ROCKCHIP_SPI_IMAGE=y to build a bootable SPI flash
image, u-boot-rockchip-spi.bin.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <foss+u-boot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
TPL max size is limited to 184 KB, SPL is loaded to 0x0 and TF-A is
loaded to 0x40000, this limit SPL max size to 256 KB. With BootRom only
reading first 2 KB per 4 KB page of SPI flash, 880 KB may be needed for
TPL+SPL in a worst-case scenario. (184 KB + 256 KB) x 2 = 880 KB
Use 0xE0000 (896 KB) as the payload offset in SPI flash, this allows
for a payload of 3168 KB before env offset start to overlap.
Also add CONFIG_ROCKCHIP_SPI_IMAGE=y to build a bootable SPI flash
image, u-boot-rockchip-spi.bin.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <foss+u-boot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
TPL max size is limited to 184 KB, SPL is loaded to 0x0 and TF-A is
loaded to 0x40000, this limit SPL max size to 256 KB. With BootRom only
reading first 2 KB per 4 KB page of SPI flash, 880 KB may be needed for
TPL+SPL in a worst-case scenario. (184 KB + 256 KB) x 2 = 880 KB
Use 0xE0000 (896 KB) as the payload offset in SPI flash, this allows
for a payload of 3168 KB before env offset start to overlap.
Also remove CONFIG_LTO=y now that there is sufficient space for SPL in
SPI flash, and to fix a build issue reported by Peter Robinson.
Fixes: 5713135ecc ("rockchip: rockpro64: Build u-boot-rockchip-spi.bin")
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <foss+u-boot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 SOQuartz compute module is mostly pin-compatible with the RPi
CM4 form factor. Therefore, it can slot into the official Raspberry Pi
CM4 IO carrier board. Add this configuration to U-Boot.
Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 SOQuartz Blade board is a carrier board for the SOQuartz
CM4-compatible compute module. It features PoE, an M.2 slot, an SD card
slot, HDMI, USB, serial and ethernet.
Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- PCIe/NVMe
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 SOQuartz Model A board is a carrier board for the SOQuartz
CM4-compatible compute module. It exposes PCIe, ethernet, USB, HDMI,
CSI, DSI, eDP and a 40 pin GPIO header, and is powered by 12V DC.
Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 Quartz64 Model B is a credit-card sized single-board
computer based on the Rockchip RK3566 SoC. The board features an M.2
PCIe slot, USB3, USB2, eMMC, SD, ethernet, HDMI, analog audio out, a
40 pin GPIO header and a DSI and CSI port, as well as on-board Wi-Fi.
Features tested on a Quartz64-B 4GB v1.4 2022-06-06:
- SD-card boot
- eMMC boot
- SPI Flash boot
- PCIe/NVMe
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 Quartz64 Model A is a single-board computer based on the
Rockchip RK3566 SoC. The board features USB3, SATA, PCIe, HDMI, USB2.0,
CSI, DSI, eDP, eMMC, SD, and an e-paper parallel port, as well as a
20 pin GPIO header.
Features tested on a Quartz64-A 8GB v2.0 2021-04-27:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Change RK3568 devices to use the newer dwc3-generic driver instead of
the old xhci-dwc3 driver for USB 3.0 support.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Commit ec107f04b6 ("rockchip: chromebook_minnie: Enable sound") and
commit 2d0c01b8f0 ("sound: rockchip: Add sound support for jerry")
enable audio support for chromebook_minnie and chromebook_jerry. Enable
it for chromebook_speedy as well, but put the non-upstream sound node
in the board -u-boot.dtsi instead.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sound support for chromebook_jerry needs the MAX98090 codec driver. This
was enabled in commit 2d0c01b8f0 ("sound: rockchip: Add sound support
for jerry"), but apparently lost in commit 7ae2729401 ("configs:
Resync with savedefconfig"). Enable it again.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # chromebook_jerry
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Commit 815ed79d83 ("video: rockchip: Use TrueType fonts with jerry")
enables makes chromebook_jerry use TrueType fonts. Make other veyron
boards switch to it as well.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Commit eba768c545 ("rockchip: jerry: Add serial support") enables
ROCKCHIP_SERIAL for chromebook_jerry to make the serial console work
correctly. Enable it also for other veyron boards.
Also enable logging and disable scrolling multiple lines at once as in
chromebook_jerry, and enable silent console as chromebook_minnie does.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Commit 70e351bdfe ("rockchip: jerry: Enable RESET driver") enables
DM_RESET for chromebook_jerry to fix its display as required by changes
to the Rockchip video drivers. Enable it for other veyron boards as
well.
Fixes: cd529f7ad6 ("rockchip: video: edp: Add missing reset support")
Fixes: 9749d2ea29 ("rockchip: video: vop: Add reset support")
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # chromebook_jerry
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
DEBUG_UART_SKIP_INIT feature is implemented only by s5p (DEBUG_UART_S5P)
and pl01x (DEBUG_UART_PL010 or DEBUG_UART_PL011) serial drivers, but all
ARCH_ROCKCHIP configs rely on default DEBUG_UART_NS16550. The ns16550
serial driver does not depends on DEBUG_UART_SKIP_INIT, so drop it from
rockchip configs.
Signed-off-by: Massimo Pegorer <massimo.pegorer@vimar.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Call to board_debug_uart_init() is useless, as mainline U-Boot can
not build TPL for rk3308, and proprietary ddr.bin to be used as TPL
is responsible to init debug uart. Moreover current implementation
of board_debug_uart_init() is not compatible with ROCK Pi S, as it
sets pins for UART2 channel 1 breaking access to sdmmc due to pinmux
conflict. Debug uart for ROCK Pi S is UART0.
Thus, avoid ROCKCHIP_RK3308 to select DEBUG_UART_BOARD_INIT and allow
to deselct it in rock-pi-s-rk3308_defconfig. The DEBUG_UART_BOARD_INIT
is already implied by ARCH_ROCKCHIP, therefore other boards based on
rk3308 chip are not affected by change.
Signed-off-by: Massimo Pegorer <massimo.pegorer@vimar.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- Resync some of the K3 DTS files with the kernel, and pull in some
required related updates to keep drivers in sync with the dts files
now. Bring in some incremental fixes on top of one of the series I
applied recently as well as updating the iot2050 platform. Also do a
few small updates to the K2 platforms.
This is more complex than it needs to be and makes converting these
boards over to plain text env files more difficult. Remove setting
mtdparts as the DTS already contain the partitions. While here also
drop the conflicting definitions from the K2 defconfigs.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This was regressed by the following commit and is required to build with
additional configs enabled.
Fixes: 14439cd71c ("configs: k3: make consistent bootcmd across all k3 socs")
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Tested-by: Nikhil M Jain <n-jain1@ti.com>
Only accept SPACE to stop autobooting. This is safer to avoid accidental
interruptions on unattended devices.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
This avoids having to maintain to defconfigs that are 99% equivalent.
The approach is to use binman to generate two flash images,
flash-pg1.bin and flash-pg2.bin. With the help of a template dtsi, we
can avoid duplicating the common binman image definitions.
Suggested-by: Andrew Davis <afd@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
The common env bits now come via ti_armv7_common.env, include it.
Furthermore restore the board-specific boot targets and their ordering
that is now enforced k3-wide differently. Finally, enable
CONFIG_LEGACY_IMAGE_FORMAT explicitly which got lost while turning
FIT_SIGNATURE on by default for k3 devices.
Fixes: 53873974 ("include: armv7: Enable distroboot across all configs")
Fixes: 4ae1a247 ("env: Make common bootcmd across all k3 devices")
Fixes: 86fab110 ("Kconfig: Enable FIT_SIGNATURE if ARM64")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Hardkernel ODROID-M1 is a single board computer with a RK3568B2 SoC,
a slightly modified version of the RK3568 SoC.
Features tested on a ODROID-M1 8GB v1.0 2022-06-13:
- SD-card boot
- eMMC boot
- SPI Flash boot
- PCIe/NVMe/AHCI
- SATA port
- USB host
Device tree is imported from linux v6.4.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
